include/configs/mx6cuboxi.h

   1 /*
   2  * Copyright (C) 2015 Freescale Semiconductor, Inc.
   3  *
   4  * Configuration settings for the SolidRun mx6 based boards
   5  *
   6  * SPDX-License-Identifier:     GPL-2.0+
   7  */
   8 #ifndef __MX6CUBOXI_CONFIG_H
   9 #define __MX6CUBOXI_CONFIG_H
  10
  11 #include <config_distro_defaults.h>
  12 #include "mx6_common.h"
  13
  14 #include "imx6_spl.h"
  15
  16 #define CONFIG_IMX_THERMAL
  17
  18 #define CONFIG_SYS_MALLOC_LEN           (10 * SZ_1M)
  19 #define CONFIG_BOARD_EARLY_INIT_F
  20 #define CONFIG_BOARD_LATE_INIT
  21 #define CONFIG_MXC_UART
  22
  23 /* MMC Configs */
  24 #define CONFIG_SYS_FSL_ESDHC_ADDR       USDHC2_BASE_ADDR
  25
  26 /* Ethernet Configuration */
  27 #define CONFIG_FEC_MXC
  28 #define CONFIG_MII
  29 #define IMX_FEC_BASE                    ENET_BASE_ADDR
  30 #define CONFIG_FEC_XCV_TYPE             RGMII
  31 #define CONFIG_FEC_MXC_PHYADDR          0
  32 #define CONFIG_PHYLIB
  33 #define CONFIG_PHY_ATHEROS
  34
  35 /* Framebuffer */
  36 #define CONFIG_VIDEO_IPUV3
  37 #define CONFIG_IPUV3_CLK                260000000
  38 #define CONFIG_CFB_CONSOLE
  39 #define CONFIG_VGA_AS_SINGLE_DEVICE
  40 #define CONFIG_VIDEO_BMP_RLE8
  41 #define CONFIG_SPLASH_SCREEN
  42 #define CONFIG_SPLASH_SCREEN_ALIGN
  43 #define CONFIG_BMP_16BPP
  44 #define CONFIG_VIDEO_LOGO
  45 #define CONFIG_VIDEO_BMP_LOGO
  46 #define CONFIG_IMX_HDMI
  47 #define CONFIG_CMD_HDMIDETECT
  48 #define CONFIG_IMX_VIDEO_SKIP
  49
  50 /* USB */
  51 #define CONFIG_USB_EHCI
  52 #define CONFIG_USB_EHCI_MX6
  53 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
  54 #define CONFIG_MXC_USB_PORTSC           (PORT_PTS_UTMI | PORT_PTS_PTW)
  55 #define CONFIG_MXC_USB_FLAGS            0
  56 #define CONFIG_USB_MAX_CONTROLLER_COUNT 2
  57 #define CONFIG_USB_KEYBOARD
  58 #define CONFIG_SYS_USB_EVENT_POLL
  59 #define CONFIG_PREBOOT \
  60         "if hdmidet; then " \
  61                 "usb start; "                  \
  62                 "setenv stdin  serial,usbkbd; "\
  63                 "setenv stdout serial,vga; "   \
  64                 "setenv stderr serial,vga; "   \
  65         "else " \
  66                 "setenv stdin  serial; " \
  67                 "setenv stdout serial; " \
  68                 "setenv stderr serial; " \
  69         "fi;"
  70
  71 /* Command definition */
  72
  73 #define CONFIG_MXC_UART_BASE    UART1_BASE
  74 #define CONSOLE_DEV     "ttymxc0"
  75 #define CONFIG_SYS_FSL_USDHC_NUM        1
  76 #define CONFIG_SYS_MMC_ENV_DEV          0       /* SDHC2 */
  77
  78 #define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
  79 #ifndef CONFIG_SPL_BUILD
  80 #define CONFIG_EXTRA_ENV_SETTINGS \
  81         "fdtfile=undefined\0" \
  82         "fdt_addr_r=0x18000000\0" \
  83         "fdt_addr=0x18000000\0" \
  84         "kernel_addr_r=" __stringify(CONFIG_LOADADDR) "\0"  \
  85         "pxefile_addr_r=" __stringify(CONFIG_LOADADDR) "\0" \
  86         "scriptaddr=" __stringify(CONFIG_LOADADDR) "\0" \
  87         "ramdisk_addr_r=0x13000000\0" \
  88         "ramdiskaddr=0x13000000\0" \
  89         "initrd_high=0xffffffff\0" \
  90         "fdt_high=0xffffffff\0" \
  91         "ip_dyn=yes\0" \
  92         "console=" CONSOLE_DEV "\0" \
  93         "bootm_size=0x10000000\0" \
  94         "mmcdev=" __stringify(CONFIG_SYS_MMC_ENV_DEV) "\0" \
  95         "update_sd_firmware=" \
  96                 "if test ${ip_dyn} = yes; then " \
  97                         "setenv get_cmd dhcp; " \
  98                 "else " \
  99                         "setenv get_cmd tftp; " \
 100                 "fi; " \
 101                 "if mmc dev ${mmcdev}; then "   \
 102                         "if ${get_cmd} ${update_sd_firmware_filename}; then " \
 103                                 "setexpr fw_sz ${filesize} / 0x200; " \
 104                                 "setexpr fw_sz ${fw_sz} + 1; "  \
 105                                 "mmc write ${loadaddr} 0x2 ${fw_sz}; " \
 106                         "fi; "  \
 107                 "fi\0" \
 108         "findfdt="\
 109                 "if test $board_name = HUMMINGBOARD && test $board_rev = MX6Q ; then " \
 110                         "setenv fdtfile imx6q-hummingboard.dtb; fi; " \
 111                 "if test $board_name = HUMMINGBOARD && test $board_rev = MX6DL ; then " \
 112                         "setenv fdtfile imx6dl-hummingboard.dtb; fi; " \
 113                 "if test $board_name = CUBOXI && test $board_rev = MX6Q ; then " \
 114                         "setenv fdtfile imx6q-cubox-i.dtb; fi; " \
 115                 "if test $board_name = CUBOXI && test $board_rev = MX6DL ; then " \
 116                         "setenv fdtfile imx6dl-cubox-i.dtb; fi; " \
 117                 "if test $fdtfile = undefined; then " \
 118                         "echo WARNING: Could not determine dtb to use; fi; \0" \
 119         BOOTENV
 120
 121 #define CONFIG_BOOTCOMMAND \
 122         "run findfdt; " \
 123         "run distro_bootcmd"
 124
 125 #define BOOT_TARGET_DEVICES(func) \
 126         func(MMC, mmc, 0) \
 127         func(USB, usb, 0) \
 128         func(PXE, pxe, na) \
 129         func(DHCP, dhcp, na)
 130
 131 #include <config_distro_bootcmd.h>
 132
 133 #else
 134 #define CONFIG_EXTRA_ENV_SETTINGS
 135 #endif /* CONFIG_SPL_BUILD */
 136
 137 /* Physical Memory Map */
 138 #define CONFIG_NR_DRAM_BANKS           1
 139 #define CONFIG_SYS_SDRAM_BASE          MMDC0_ARB_BASE_ADDR
 140 #define CONFIG_SYS_INIT_RAM_ADDR       IRAM_BASE_ADDR
 141 #define CONFIG_SYS_INIT_RAM_SIZE       IRAM_SIZE
 142
 143 #define CONFIG_SYS_INIT_SP_OFFSET \
 144         (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 145 #define CONFIG_SYS_INIT_SP_ADDR \
 146         (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
 147
 148 /* Environment organization */
 149 #define CONFIG_ENV_SIZE                 (8 * 1024)
 150 #define CONFIG_ENV_IS_IN_MMC
 151 #define CONFIG_ENV_OFFSET               (8 * 64 * 1024)
 152
 153 #endif                         /* __MX6CUBOXI_CONFIG_H */