include/configs/mx53loco.h

   1 /*
   2  * Copyright (C) 2011 Freescale Semiconductor, Inc.
   3  * Jason Liu <r64343@freescale.com>
   4  *
   5  * Configuration settings for Freescale MX53 low cost board.
   6  *
   7  * SPDX-License-Identifier:     GPL-2.0+
   8  */
   9
  10 #ifndef __CONFIG_H
  11 #define __CONFIG_H
  12
  13 #define CONFIG_MX53
  14
  15 #define CONFIG_MACH_TYPE        MACH_TYPE_MX53_LOCO
  16
  17 #include <asm/arch/imx-regs.h>
  18
  19 #define CONFIG_CMDLINE_TAG
  20 #define CONFIG_SETUP_MEMORY_TAGS
  21 #define CONFIG_INITRD_TAG
  22
  23 #define CONFIG_SYS_FSL_CLK
  24
  25 /* Size of malloc() pool */
  26 #define CONFIG_SYS_MALLOC_LEN           (10 * 1024 * 1024)
  27
  28 #define CONFIG_BOARD_EARLY_INIT_F
  29 #define CONFIG_BOARD_LATE_INIT
  30 #define CONFIG_MXC_GPIO
  31 #define CONFIG_REVISION_TAG
  32
  33 #define CONFIG_MXC_UART
  34 #define CONFIG_MXC_UART_BASE    UART1_BASE
  35
  36 /* MMC Configs */
  37 #define CONFIG_FSL_ESDHC
  38 #define CONFIG_SYS_FSL_ESDHC_ADDR       0
  39 #define CONFIG_SYS_FSL_ESDHC_NUM        2
  40
  41 #define CONFIG_GENERIC_MMC
  42 #define CONFIG_DOS_PARTITION
  43
  44 /* Eth Configs */
  45 #define CONFIG_MII
  46
  47 #define CONFIG_FEC_MXC
  48 #define IMX_FEC_BASE    FEC_BASE_ADDR
  49 #define CONFIG_FEC_MXC_PHYADDR  0x1F
  50
  51 /* USB Configs */
  52 #define CONFIG_USB_EHCI
  53 #define CONFIG_USB_EHCI_MX5
  54 #define CONFIG_USB_HOST_ETHER
  55 #define CONFIG_USB_ETHER_ASIX
  56 #define CONFIG_USB_ETHER_MCS7830
  57 #define CONFIG_USB_ETHER_SMSC95XX
  58 #define CONFIG_MXC_USB_PORT     1
  59 #define CONFIG_MXC_USB_PORTSC   (PORT_PTS_UTMI | PORT_PTS_PTW)
  60 #define CONFIG_MXC_USB_FLAGS    0
  61
  62 /* I2C Configs */
  63 #define CONFIG_SYS_I2C
  64 #define CONFIG_SYS_I2C_MXC
  65 #define CONFIG_SYS_I2C_MXC_I2C1         /* enable I2C bus 1 */
  66 #define CONFIG_SYS_I2C_MXC_I2C2         /* enable I2C bus 2 */
  67 #define CONFIG_SYS_I2C_MXC_I2C3         /* enable I2C bus 3 */
  68
  69 /* PMIC Controller */
  70 #define CONFIG_POWER
  71 #define CONFIG_POWER_I2C
  72 #define CONFIG_DIALOG_POWER
  73 #define CONFIG_POWER_FSL
  74 #define CONFIG_POWER_FSL_MC13892
  75 #define CONFIG_SYS_DIALOG_PMIC_I2C_ADDR 0x48
  76 #define CONFIG_SYS_FSL_PMIC_I2C_ADDR    0x8
  77
  78 /* allow to overwrite serial and ethaddr */
  79 #define CONFIG_ENV_OVERWRITE
  80 #define CONFIG_CONS_INDEX               1
  81 #define CONFIG_BAUDRATE                 115200
  82
  83 /* Command definition */
  84 #define CONFIG_SUPPORT_RAW_INITRD
  85
  86
  87 #define CONFIG_ETHPRIME         "FEC0"
  88
  89 #define CONFIG_LOADADDR         0x72000000      /* loadaddr env var */
  90 #define CONFIG_SYS_TEXT_BASE    0x77800000
  91
  92 #define CONFIG_EXTRA_ENV_SETTINGS \
  93         "script=boot.scr\0" \
  94         "image=zImage\0" \
  95         "fdt_addr=0x71000000\0" \
  96         "boot_fdt=try\0" \
  97         "ip_dyn=yes\0" \
  98         "mmcdev=0\0" \
  99         "mmcpart=1\0" \
 100         "mmcroot=/dev/mmcblk0p2 rw rootwait\0" \
 101         "mmcargs=setenv bootargs console=ttymxc0,${baudrate} root=${mmcroot}\0" \
 102         "loadbootscript=" \
 103                 "load mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
 104         "bootscript=echo Running bootscript from mmc ...; " \
 105                 "source\0" \
 106         "loadimage=load mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
 107         "loadfdt=load mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
 108         "mmcboot=echo Booting from mmc ...; " \
 109                 "run mmcargs; " \
 110                 "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
 111                         "if run loadfdt; then " \
 112                                 "bootz ${loadaddr} - ${fdt_addr}; " \
 113                         "else " \
 114                                 "if test ${boot_fdt} = try; then " \
 115                                         "bootz; " \
 116                                 "else " \
 117                                         "echo WARN: Cannot load the DT; " \
 118                                 "fi; " \
 119                         "fi; " \
 120                 "else " \
 121                         "bootz; " \
 122                 "fi;\0" \
 123         "netargs=setenv bootargs console=ttymxc0,${baudrate} " \
 124                 "root=/dev/nfs " \
 125                 "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
 126         "netboot=echo Booting from net ...; " \
 127                 "run netargs; " \
 128                 "if test ${ip_dyn} = yes; then " \
 129                         "setenv get_cmd dhcp; " \
 130                 "else " \
 131                         "setenv get_cmd tftp; " \
 132                 "fi; " \
 133                 "${get_cmd} ${image}; " \
 134                 "if test ${boot_fdt} = yes ||  test ${boot_fdt} = try; then " \
 135                         "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
 136                                 "bootz ${loadaddr} - ${fdt_addr}; " \
 137                         "else " \
 138                                 "if test ${boot_fdt} = try; then " \
 139                                         "bootz; " \
 140                                 "else " \
 141                                         "echo ERROR: Cannot load the DT; " \
 142                                         "exit; " \
 143                                 "fi; " \
 144                         "fi; " \
 145                 "else " \
 146                         "bootz; " \
 147                 "fi;\0"
 148
 149 #define CONFIG_BOOTCOMMAND \
 150         "mmc dev ${mmcdev}; if mmc rescan; then " \
 151                 "if run loadbootscript; then " \
 152                         "run bootscript; " \
 153                 "else " \
 154                         "if run loadimage; then " \
 155                                 "run mmcboot; " \
 156                         "else run netboot; " \
 157                         "fi; " \
 158                 "fi; " \
 159         "else run netboot; fi"
 160
 161 #define CONFIG_ARP_TIMEOUT      200UL
 162
 163 /* Miscellaneous configurable options */
 164 #define CONFIG_SYS_LONGHELP             /* undef to save memory */
 165 #define CONFIG_AUTO_COMPLETE
 166 #define CONFIG_SYS_CBSIZE               512     /* Console I/O Buffer Size */
 167
 168 #define CONFIG_SYS_MAXARGS      16      /* max number of command args */
 169 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
 170
 171 #define CONFIG_SYS_MEMTEST_START       0x70000000
 172 #define CONFIG_SYS_MEMTEST_END         0x70010000
 173
 174 #define CONFIG_SYS_LOAD_ADDR            CONFIG_LOADADDR
 175
 176 #define CONFIG_CMDLINE_EDITING
 177
 178 /* Physical Memory Map */
 179 #define CONFIG_NR_DRAM_BANKS    2
 180 #define PHYS_SDRAM_1                    CSD0_BASE_ADDR
 181 #define PHYS_SDRAM_1_SIZE               (gd->bd->bi_dram[0].size)
 182 #define PHYS_SDRAM_2                    CSD1_BASE_ADDR
 183 #define PHYS_SDRAM_2_SIZE               (gd->bd->bi_dram[1].size)
 184 #define PHYS_SDRAM_SIZE                 (gd->ram_size)
 185
 186 #define CONFIG_SYS_SDRAM_BASE           (PHYS_SDRAM_1)
 187 #define CONFIG_SYS_INIT_RAM_ADDR        (IRAM_BASE_ADDR)
 188 #define CONFIG_SYS_INIT_RAM_SIZE        (IRAM_SIZE)
 189
 190 #define CONFIG_SYS_INIT_SP_OFFSET \
 191         (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 192 #define CONFIG_SYS_INIT_SP_ADDR \
 193         (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
 194
 195 /* FLASH and environment organization */
 196 #define CONFIG_SYS_NO_FLASH
 197
 198 #define CONFIG_ENV_OFFSET      (6 * 64 * 1024)
 199 #define CONFIG_ENV_SIZE        (8 * 1024)
 200 #define CONFIG_ENV_IS_IN_MMC
 201 #define CONFIG_SYS_MMC_ENV_DEV 0
 202
 203 #define CONFIG_CMD_SATA
 204 #ifdef CONFIG_CMD_SATA
 205         #define CONFIG_DWC_AHSATA
 206         #define CONFIG_SYS_SATA_MAX_DEVICE      1
 207         #define CONFIG_DWC_AHSATA_PORT_ID       0
 208         #define CONFIG_DWC_AHSATA_BASE_ADDR     SATA_BASE_ADDR
 209         #define CONFIG_LBA48
 210         #define CONFIG_LIBATA
 211 #endif
 212
 213 /* Framebuffer and LCD */
 214 #define CONFIG_PREBOOT
 215 #define CONFIG_VIDEO_IPUV3
 216 #define CONFIG_VIDEO_BMP_RLE8
 217 #define CONFIG_SPLASH_SCREEN
 218 #define CONFIG_BMP_16BPP
 219 #define CONFIG_VIDEO_LOGO
 220 #define CONFIG_IPUV3_CLK        200000000
 221
 222 #endif                          /* __CONFIG_H */