include/configs/mpc5121ads.h

   1 /*
   2  * (C) Copyright 2007-2009 DENX Software Engineering
   3  *
   4  * SPDX-License-Identifier:     GPL-2.0+
   5  */
   6
   7 /*
   8  * MPC5121ADS board configuration file
   9  */
  10
  11 #ifndef __CONFIG_H
  12 #define __CONFIG_H
  13
  14 #define CONFIG_MPC5121ADS 1
  15
  16 /*
  17  * Memory map for the MPC5121ADS board:
  18  *
  19  * 0x0000_0000 - 0x0FFF_FFFF    DDR RAM (256 MB)
  20  * 0x3000_0000 - 0x3001_FFFF    SRAM (128 KB)
  21  * 0x8000_0000 - 0x803F_FFFF    IMMR (4 MB)
  22  * 0x8200_0000 - 0x8200_001F    CPLD (32 B)
  23  * 0x8400_0000 - 0x82FF_FFFF    PCI I/O space (16 MB)
  24  * 0xA000_0000 - 0xAFFF_FFFF    PCI memory space (256 MB)
  25  * 0xB000_0000 - 0xBFFF_FFFF    PCI memory mapped I/O space (256 MB)
  26  * 0xFC00_0000 - 0xFFFF_FFFF    NOR Boot FLASH (64 MB)
  27  */
  28
  29 /*
  30  * High Level Configuration Options
  31  */
  32 #define CONFIG_E300             1       /* E300 Family */
  33
  34 #define CONFIG_SYS_TEXT_BASE    0xFFF00000
  35
  36 /* video */
  37 #ifdef CONFIG_FSL_DIU_FB
  38 #define CONFIG_SYS_DIU_ADDR     (CONFIG_SYS_IMMR + 0x2100)
  39 #define CONFIG_CMD_BMP
  40 #define CONFIG_VIDEO_LOGO
  41 #define CONFIG_VIDEO_BMP_LOGO
  42 #endif
  43
  44 /* CONFIG_PCI is defined at config time */
  45
  46 #ifdef CONFIG_MPC5121ADS_REV2
  47 #define CONFIG_SYS_MPC512X_CLKIN        66000000        /* in Hz */
  48 #else
  49 #define CONFIG_SYS_MPC512X_CLKIN        33333333        /* in Hz */
  50 #define CONFIG_PCI
  51 #endif
  52
  53 #define CONFIG_BOARD_EARLY_INIT_F               /* call board_early_init_f() */
  54 #define CONFIG_MISC_INIT_R
  55
  56 #define CONFIG_SYS_IMMR         0x80000000
  57
  58 #define CONFIG_SYS_MEMTEST_START        0x00200000      /* memtest region */
  59 #define CONFIG_SYS_MEMTEST_END          0x00400000
  60
  61 /*
  62  * DDR Setup - manually set all parameters as there's no SPD etc.
  63  */
  64 #ifdef CONFIG_MPC5121ADS_REV2
  65 #define CONFIG_SYS_DDR_SIZE             256             /* MB */
  66 #else
  67 #define CONFIG_SYS_DDR_SIZE             512             /* MB */
  68 #endif
  69 #define CONFIG_SYS_DDR_BASE             0x00000000      /* DDR is system memory*/
  70 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_BASE
  71 #define CONFIG_SYS_MAX_RAM_SIZE         0x20000000
  72
  73 #define CONFIG_SYS_IOCTRL_MUX_DDR       0x00000036
  74
  75 /* DDR Controller Configuration
  76  *
  77  * SYS_CFG:
  78  *      [31:31] MDDRC Soft Reset:       Diabled
  79  *      [30:30] DRAM CKE pin:           Enabled
  80  *      [29:29] DRAM CLK:               Enabled
  81  *      [28:28] Command Mode:           Enabled (For initialization only)
  82  *      [27:25] DRAM Row Select:        dram_row[15:0] = magenta_address[25:10]
  83  *      [24:21] DRAM Bank Select:       dram_bank[1:0] = magenta_address[11:10]
  84  *      [20:19] Read Test:              DON'T USE
  85  *      [18:18] Self Refresh:           Enabled
  86  *      [17:17] 16bit Mode:             Disabled
  87  *      [16:13] Ready Delay:            2
  88  *      [12:12] Half DQS Delay:         Disabled
  89  *      [11:11] Quarter DQS Delay:      Disabled
  90  *      [10:08] Write Delay:            2
  91  *      [07:07] Early ODT:              Disabled
  92  *      [06:06] On DIE Termination:     Disabled
  93  *      [05:05] FIFO Overflow Clear:    DON'T USE here
  94  *      [04:04] FIFO Underflow Clear:   DON'T USE here
  95  *      [03:03] FIFO Overflow Pending:  DON'T USE here
  96  *      [02:02] FIFO Underlfow Pending: DON'T USE here
  97  *      [01:01] FIFO Overlfow Enabled:  Enabled
  98  *      [00:00] FIFO Underflow Enabled: Enabled
  99  * TIME_CFG0
 100  *      [31:16] DRAM Refresh Time:      0 CSB clocks
 101  *      [15:8]  DRAM Command Time:      0 CSB clocks
 102  *      [07:00] DRAM Precharge Time:    0 CSB clocks
 103  * TIME_CFG1
 104  *      [31:26] DRAM tRFC:
 105  *      [25:21] DRAM tWR1:
 106  *      [20:17] DRAM tWRT1:
 107  *      [16:11] DRAM tDRR:
 108  *      [10:05] DRAM tRC:
 109  *      [04:00] DRAM tRAS:
 110  * TIME_CFG2
 111  *      [31:28] DRAM tRCD:
 112  *      [27:23] DRAM tFAW:
 113  *      [22:19] DRAM tRTW1:
 114  *      [18:15] DRAM tCCD:
 115  *      [14:10] DRAM tRTP:
 116  *      [09:05] DRAM tRP:
 117  *      [04:00] DRAM tRPA
 118  */
 119 #ifdef CONFIG_MPC5121ADS_REV2
 120 #define CONFIG_SYS_MDDRC_SYS_CFG        0xE8604A00
 121 #define CONFIG_SYS_MDDRC_TIME_CFG1      0x54EC1168
 122 #define CONFIG_SYS_MDDRC_TIME_CFG2      0x35210864
 123 #else
 124 #define CONFIG_SYS_MDDRC_SYS_CFG        0xEA804A00
 125 #define CONFIG_SYS_MDDRC_TIME_CFG1      0x68EC1168
 126 #define CONFIG_SYS_MDDRC_TIME_CFG2      0x34310864
 127 #endif
 128 #define CONFIG_SYS_MDDRC_TIME_CFG0      0x06183D2E
 129
 130 #define CONFIG_SYS_MDDRC_SYS_CFG_ELPIDA         0xEA802B00
 131 #define CONFIG_SYS_MDDRC_TIME_CFG1_ELPIDA       0x690e1189
 132 #define CONFIG_SYS_MDDRC_TIME_CFG2_ELPIDA       0x35310864
 133
 134 #define CONFIG_SYS_DDRCMD_NOP           0x01380000
 135 #define CONFIG_SYS_DDRCMD_PCHG_ALL      0x01100400
 136 #define CONFIG_SYS_DDRCMD_EM2           0x01020000
 137 #define CONFIG_SYS_DDRCMD_EM3           0x01030000
 138 #define CONFIG_SYS_DDRCMD_EN_DLL        0x01010000
 139 #define CONFIG_SYS_DDRCMD_RFSH          0x01080000
 140
 141 #define DDRCMD_EMR_OCD(pr, ohm) ( \
 142         (1 << 24)          | /* MDDRC Command Request   */ \
 143         (1 << 16)          | /* MODE Reg BA[2:0]        */ \
 144         (0 << 12)          | /* Outputs 0=Enabled       */ \
 145         (0 << 11)          | /* RDQS                    */ \
 146         (1 << 10)          | /* DQS#                    */ \
 147         (pr <<  7)         | /* OCD prog 7=deflt,0=exit */ \
 148                     /* ODT Rtt[1:0] 0=0,1=75,2=150,3=50 */ \
 149         ((ohm & 0x2) <<  5)| /* Rtt1                    */ \
 150         (0 <<  3)          | /* additive posted CAS#    */ \
 151         ((ohm & 0x1) <<  2)| /* Rtt0                    */ \
 152         (0 <<  0)          | /* Output Drive Strength   */ \
 153         (0 <<  0))           /* DLL Enable 0=Normal     */
 154
 155 #define CONFIG_SYS_DDRCMD_OCD_DEFAULT   DDRCMD_EMR_OCD(7, 0)
 156 #define CONFIG_SYS_ELPIDA_OCD_EXIT      DDRCMD_EMR_OCD(0, 0)
 157
 158 #define DDRCMD_MODE_REG(cas, wr) ( \
 159         (1 << 24)    | /* MDDRC Command Request                 */ \
 160         (0 << 16)    | /* MODE Reg BA[2:0]                      */ \
 161         ((wr-1) << 9)| /* Write Recovery                        */ \
 162         (cas << 4)   | /* CAS                                   */ \
 163         (0 << 3)     | /* Burst Type:0=Sequential,1=Interleaved */ \
 164         (2 << 0))      /* 4 or 8 Burst Length:0x2=4 0x3=8       */
 165
 166 #define CONFIG_SYS_MICRON_INIT_DEV_OP   DDRCMD_MODE_REG(3, 3)
 167 #define CONFIG_SYS_ELPIDA_INIT_DEV_OP   DDRCMD_MODE_REG(4, 4)
 168 #define CONFIG_SYS_ELPIDA_RES_DLL       (DDRCMD_MODE_REG(4, 4) | (1 << 8))
 169
 170 /* DDR Priority Manager Configuration */
 171 #define CONFIG_SYS_MDDRCGRP_PM_CFG1     0x00077777
 172 #define CONFIG_SYS_MDDRCGRP_PM_CFG2     0x00000000
 173 #define CONFIG_SYS_MDDRCGRP_HIPRIO_CFG  0x00000001
 174 #define CONFIG_SYS_MDDRCGRP_LUT0_MU     0xFFEEDDCC
 175 #define CONFIG_SYS_MDDRCGRP_LUT0_ML     0xBBAAAAAA
 176 #define CONFIG_SYS_MDDRCGRP_LUT1_MU     0x66666666
 177 #define CONFIG_SYS_MDDRCGRP_LUT1_ML     0x55555555
 178 #define CONFIG_SYS_MDDRCGRP_LUT2_MU     0x44444444
 179 #define CONFIG_SYS_MDDRCGRP_LUT2_ML     0x44444444
 180 #define CONFIG_SYS_MDDRCGRP_LUT3_MU     0x55555555
 181 #define CONFIG_SYS_MDDRCGRP_LUT3_ML     0x55555558
 182 #define CONFIG_SYS_MDDRCGRP_LUT4_MU     0x11111111
 183 #define CONFIG_SYS_MDDRCGRP_LUT4_ML     0x11111122
 184 #define CONFIG_SYS_MDDRCGRP_LUT0_AU     0xaaaaaaaa
 185 #define CONFIG_SYS_MDDRCGRP_LUT0_AL     0xaaaaaaaa
 186 #define CONFIG_SYS_MDDRCGRP_LUT1_AU     0x66666666
 187 #define CONFIG_SYS_MDDRCGRP_LUT1_AL     0x66666666
 188 #define CONFIG_SYS_MDDRCGRP_LUT2_AU     0x11111111
 189 #define CONFIG_SYS_MDDRCGRP_LUT2_AL     0x11111111
 190 #define CONFIG_SYS_MDDRCGRP_LUT3_AU     0x11111111
 191 #define CONFIG_SYS_MDDRCGRP_LUT3_AL     0x11111111
 192 #define CONFIG_SYS_MDDRCGRP_LUT4_AU     0x11111111
 193 #define CONFIG_SYS_MDDRCGRP_LUT4_AL     0x11111111
 194
 195 /*
 196  * NOR FLASH on the Local Bus
 197  */
 198 #undef CONFIG_BKUP_FLASH
 199 #define CONFIG_SYS_FLASH_CFI                            /* use the Common Flash Interface */
 200 #define CONFIG_FLASH_CFI_DRIVER                 /* use the CFI driver */
 201 #ifdef CONFIG_BKUP_FLASH
 202 #define CONFIG_SYS_FLASH_BASE           0xFF800000      /* start of FLASH   */
 203 #define CONFIG_SYS_FLASH_SIZE           0x00800000      /* max flash size in bytes */
 204 #else
 205 #define CONFIG_SYS_FLASH_BASE           0xFC000000      /* start of FLASH   */
 206 #define CONFIG_SYS_FLASH_SIZE           0x04000000      /* max flash size in bytes */
 207 #endif
 208 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
 209 #define CONFIG_SYS_MAX_FLASH_BANKS      1               /* number of banks */
 210 #define CONFIG_SYS_FLASH_BANKS_LIST     {CONFIG_SYS_FLASH_BASE}
 211 #define CONFIG_SYS_MAX_FLASH_SECT       256             /* max sectors per device */
 212
 213 #undef CONFIG_SYS_FLASH_CHECKSUM
 214
 215 /*
 216  * NAND FLASH
 217  * drivers/mtd/nand/mpc5121_nfc.c (rev 2 silicon only)
 218  */
 219 #define CONFIG_CMD_NAND                                 /* enable NAND support */
 220 #define CONFIG_JFFS2_NAND                               /* with JFFS2 on it */
 221 #define CONFIG_NAND_MPC5121_NFC
 222 #define CONFIG_SYS_NAND_BASE            0x40000000
 223
 224 #define CONFIG_SYS_MAX_NAND_DEVICE      2
 225 #define CONFIG_SYS_NAND_SELECT_DEVICE   /* driver supports mutipl. chips */
 226
 227 /*
 228  * Configuration parameters for MPC5121 NAND driver
 229  */
 230 #define CONFIG_FSL_NFC_WIDTH 1
 231 #define CONFIG_FSL_NFC_WRITE_SIZE 2048
 232 #define CONFIG_FSL_NFC_SPARE_SIZE 64
 233 #define CONFIG_FSL_NFC_CHIPS CONFIG_SYS_MAX_NAND_DEVICE
 234
 235 /*
 236  * CPLD registers area is really only 32 bytes in size, but the smallest possible LP
 237  * window is 64KB
 238  */
 239 #define CONFIG_SYS_CPLD_BASE            0x82000000
 240 #define CONFIG_SYS_CPLD_SIZE            0x00010000      /* 64 KB */
 241 #define CONFIG_SYS_CS2_START            CONFIG_SYS_CPLD_BASE
 242 #define CONFIG_SYS_CS2_SIZE             CONFIG_SYS_CPLD_SIZE
 243
 244 #define CONFIG_SYS_SRAM_BASE            0x30000000
 245 #define CONFIG_SYS_SRAM_SIZE            0x00020000      /* 128 KB */
 246
 247 #define CONFIG_SYS_CS0_CFG              0x05059310      /* ALE active low, data size 4bytes */
 248 #define CONFIG_SYS_CS2_CFG              0x05059010      /* ALE active low, data size 1byte */
 249 #define CONFIG_SYS_CS_ALETIMING 0x00000005      /* Use alternative CS timing for CS0 and CS2 */
 250
 251 /* Use SRAM for initial stack */
 252 #define CONFIG_SYS_INIT_RAM_ADDR        CONFIG_SYS_SRAM_BASE            /* Initial RAM address */
 253 #define CONFIG_SYS_INIT_RAM_SIZE        CONFIG_SYS_SRAM_SIZE            /* Size of used area in RAM */
 254
 255 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 256 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 257
 258 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE            /* Start of monitor */
 259 #define CONFIG_SYS_MONITOR_LEN          (512 * 1024)            /* Reserve 512 kB for Mon */
 260 #ifdef  CONFIG_FSL_DIU_FB
 261 #define CONFIG_SYS_MALLOC_LEN           (6 * 1024 * 1024)       /* Reserved for malloc */
 262 #else
 263 #define CONFIG_SYS_MALLOC_LEN           (512 * 1024)
 264 #endif
 265
 266 /*
 267  * Serial Port
 268  */
 269 #define CONFIG_CONS_INDEX     1
 270
 271 /*
 272  * Serial console configuration
 273  */
 274 #define CONFIG_PSC_CONSOLE      3       /* console is on PSC3 */
 275 #define CONFIG_SYS_PSC3
 276 #if CONFIG_PSC_CONSOLE != 3
 277 #error CONFIG_PSC_CONSOLE must be 3
 278 #endif
 279 #define CONFIG_BAUDRATE         115200  /* ... at 115200 bps */
 280 #define CONFIG_SYS_BAUDRATE_TABLE  \
 281         {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
 282
 283 #define CONSOLE_FIFO_TX_SIZE    FIFOC_PSC3_TX_SIZE
 284 #define CONSOLE_FIFO_TX_ADDR    FIFOC_PSC3_TX_ADDR
 285 #define CONSOLE_FIFO_RX_SIZE    FIFOC_PSC3_RX_SIZE
 286 #define CONSOLE_FIFO_RX_ADDR    FIFOC_PSC3_RX_ADDR
 287
 288 #define CONFIG_CMDLINE_EDITING  1       /* add command line history     */
 289
 290 /*
 291  * Clocks in use
 292  */
 293 #define SCCR1_CLOCKS_EN (CLOCK_SCCR1_CFG_EN |                           \
 294                          CLOCK_SCCR1_DDR_EN |                           \
 295                          CLOCK_SCCR1_FEC_EN |                           \
 296                          CLOCK_SCCR1_LPC_EN |                           \
 297                          CLOCK_SCCR1_NFC_EN |                           \
 298                          CLOCK_SCCR1_PATA_EN |                          \
 299                          CLOCK_SCCR1_PCI_EN |                           \
 300                          CLOCK_SCCR1_PSC_EN(CONFIG_PSC_CONSOLE) |       \
 301                          CLOCK_SCCR1_PSCFIFO_EN |                       \
 302                          CLOCK_SCCR1_TPR_EN)
 303
 304 #define SCCR2_CLOCKS_EN (CLOCK_SCCR2_DIU_EN |           \
 305                          CLOCK_SCCR2_I2C_EN |           \
 306                          CLOCK_SCCR2_MEM_EN |           \
 307                          CLOCK_SCCR2_SPDIF_EN |         \
 308                          CLOCK_SCCR2_USB1_EN |          \
 309                          CLOCK_SCCR2_USB2_EN)
 310
 311 /*
 312  * PCI
 313  */
 314 #ifdef CONFIG_PCI
 315 #define CONFIG_PCI_INDIRECT_BRIDGE
 316
 317 /*
 318  * General PCI
 319  */
 320 #define CONFIG_SYS_PCI_MEM_BASE 0xA0000000
 321 #define CONFIG_SYS_PCI_MEM_PHYS CONFIG_SYS_PCI_MEM_BASE
 322 #define CONFIG_SYS_PCI_MEM_SIZE 0x10000000      /* 256M */
 323 #define CONFIG_SYS_PCI_MMIO_BASE        (CONFIG_SYS_PCI_MEM_BASE + CONFIG_SYS_PCI_MEM_SIZE)
 324 #define CONFIG_SYS_PCI_MMIO_PHYS        CONFIG_SYS_PCI_MMIO_BASE
 325 #define CONFIG_SYS_PCI_MMIO_SIZE        0x10000000      /* 256M */
 326 #define CONFIG_SYS_PCI_IO_BASE          0x00000000
 327 #define CONFIG_SYS_PCI_IO_PHYS          0x84000000
 328 #define CONFIG_SYS_PCI_IO_SIZE          0x01000000      /* 16M */
 329
 330 #define CONFIG_PCI_PNP                  /* do pci plug-and-play */
 331
 332 #define CONFIG_PCI_SCAN_SHOW            /* show pci devices on startup */
 333
 334 #endif
 335
 336 /* I2C */
 337 #define CONFIG_HARD_I2C                 /* I2C with hardware support */
 338 #define CONFIG_I2C_MULTI_BUS
 339 #define CONFIG_SYS_I2C_SPEED            100000  /* I2C speed and slave address */
 340 #define CONFIG_SYS_I2C_SLAVE            0x7F
 341 #if 0
 342 #define CONFIG_SYS_I2C_NOPROBES {{0,0x69}}      /* Don't probe these addrs */
 343 #endif
 344
 345 /*
 346  * IIM - IC Identification Module
 347  */
 348 #undef CONFIG_FSL_IIM
 349
 350 /*
 351  * EEPROM configuration
 352  */
 353 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN          2       /* 16-bit EEPROM address */
 354 #define CONFIG_SYS_I2C_EEPROM_ADDR              0x50    /* Atmel: AT24C32A-10TQ-2.7 */
 355 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS   10      /* 10ms of delay */
 356 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS       5       /* 32-Byte Page Write Mode */
 357
 358 /*
 359  * Ethernet configuration
 360  */
 361 #define CONFIG_MPC512x_FEC      1
 362 #define CONFIG_PHY_ADDR         0x1
 363 #define CONFIG_MII              1       /* MII PHY management           */
 364 #define CONFIG_FEC_AN_TIMEOUT   1
 365 #define CONFIG_HAS_ETH0
 366
 367 /*
 368  * Configure on-board RTC
 369  */
 370 #define CONFIG_RTC_M41T62                       /* use M41T62 rtc via i2 */
 371 #define CONFIG_SYS_I2C_RTC_ADDR         0x68    /* at address 0x68              */
 372
 373 /*
 374  * USB  Support
 375  */
 376
 377 #if defined(CONFIG_CMD_USB)
 378 #define CONFIG_USB_EHCI                         /* Enable EHCI Support  */
 379 #define CONFIG_USB_EHCI_FSL                     /* On a FSL platform    */
 380 #define CONFIG_EHCI_MMIO_BIG_ENDIAN             /* With big-endian regs */
 381 #define CONFIG_EHCI_DESC_BIG_ENDIAN
 382 #define CONFIG_EHCI_IS_TDI
 383 #endif
 384
 385 /*
 386  * Environment
 387  */
 388 #define CONFIG_ENV_IS_IN_FLASH  1
 389 /* This has to be a multiple of the Flash sector size */
 390 #define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
 391 #define CONFIG_ENV_SIZE         0x2000
 392 #ifdef CONFIG_BKUP_FLASH
 393 #define CONFIG_ENV_SECT_SIZE    0x20000 /* one sector (256K) for env */
 394 #else
 395 #define CONFIG_ENV_SECT_SIZE    0x40000 /* one sector (256K) for env */
 396 #endif
 397
 398 /* Address and size of Redundant Environment Sector     */
 399 #define CONFIG_ENV_ADDR_REDUND  (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
 400 #define CONFIG_ENV_SIZE_REDUND  (CONFIG_ENV_SIZE)
 401
 402 #define CONFIG_LOADS_ECHO       1       /* echo on for serial download */
 403 #define CONFIG_SYS_LOADS_BAUD_CHANGE    1       /* allow baudrate change */
 404
 405 #define CONFIG_CMD_DATE
 406 #define CONFIG_CMD_EEPROM
 407 #define CONFIG_CMD_IDE
 408 #define CONFIG_CMD_JFFS2
 409 #define CONFIG_CMD_REGINFO
 410
 411 #undef CONFIG_CMD_FUSE
 412
 413 #if defined(CONFIG_PCI)
 414 #define CONFIG_CMD_PCI
 415 #endif
 416
 417 /*
 418  * Dynamic MTD partition support
 419  */
 420 #define CONFIG_CMD_MTDPARTS
 421 #define CONFIG_MTD_DEVICE               /* needed for mtdparts commands */
 422 #define CONFIG_FLASH_CFI_MTD
 423 #define MTDIDS_DEFAULT          "nor0=fc000000.flash,nand0=mpc5121.nand"
 424
 425 /*
 426  * NOR flash layout:
 427  *
 428  * FC000000 - FEABFFFF 42.75 MiB        User Data
 429  * FEAC0000 - FFABFFFF  16 MiB          Root File System
 430  * FFAC0000 - FFEBFFFF   4 MiB          Linux Kernel
 431  * FFEC0000 - FFEFFFFF 256 KiB          Device Tree
 432  * FFF00000 - FFFFFFFF   1 MiB          U-Boot (up to 512 KiB) and 2 x * env
 433  *
 434  * NAND flash layout: one big partition
 435  */
 436 #define MTDPARTS_DEFAULT        "mtdparts=fc000000.flash:43776k(user)," \
 437                                                 "16m(rootfs),"          \
 438                                                 "4m(kernel),"           \
 439                                                 "256k(dtb),"            \
 440                                                 "1m(u-boot);"           \
 441                                         "mpc5121.nand:-(data)"
 442
 443 #if defined(CONFIG_CMD_IDE) || defined(CONFIG_CMD_EXT2) || defined(CONFIG_CMD_USB)
 444
 445 #define CONFIG_DOS_PARTITION
 446 #define CONFIG_MAC_PARTITION
 447 #define CONFIG_ISO_PARTITION
 448
 449 #define CONFIG_SUPPORT_VFAT
 450
 451 #endif /* defined(CONFIG_CMD_IDE) */
 452
 453 /*
 454  * Watchdog timeout = CONFIG_SYS_WATCHDOG_VALUE * 65536 / IPS clock.
 455  * For example, when IPS is set to 66MHz and CONFIG_SYS_WATCHDOG_VALUE is set
 456  * to 0xFFFF, watchdog timeouts after about 64s. For details refer
 457  * to chapter 36 of the MPC5121e Reference Manual.
 458  */
 459 /* #define CONFIG_WATCHDOG */           /* enable watchdog */
 460 #define CONFIG_SYS_WATCHDOG_VALUE 0xFFFF
 461
 462  /*
 463  * Miscellaneous configurable options
 464  */
 465 #define CONFIG_SYS_LONGHELP                     /* undef to save memory */
 466 #define CONFIG_SYS_LOAD_ADDR    0x2000000       /* default load address */
 467
 468 #ifdef CONFIG_CMD_KGDB
 469         #define CONFIG_SYS_CBSIZE       1024    /* Console I/O Buffer Size */
 470 #else
 471         #define CONFIG_SYS_CBSIZE       256     /* Console I/O Buffer Size */
 472 #endif
 473
 474 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) /* Print Buffer Size */
 475 #define CONFIG_SYS_MAXARGS      16              /* max number of command args */
 476 #define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE       /* Boot Argument Buffer Size */
 477
 478 /*
 479  * For booting Linux, the board info and command line data
 480  * have to be in the first 256 MB of memory, since this is
 481  * the maximum mapped by the Linux kernel during initialization.
 482  */
 483 #define CONFIG_SYS_BOOTMAPSZ    (256 << 20)     /* Initial Memory map for Linux*/
 484
 485 /* Cache Configuration */
 486 #define CONFIG_SYS_DCACHE_SIZE          32768
 487 #define CONFIG_SYS_CACHELINE_SIZE       32
 488 #ifdef CONFIG_CMD_KGDB
 489 #define CONFIG_SYS_CACHELINE_SHIFT      5       /*log base 2 of the above value*/
 490 #endif
 491
 492 #define CONFIG_SYS_HID0_INIT    0x000000000
 493 #define CONFIG_SYS_HID0_FINAL   (HID0_ENABLE_MACHINE_CHECK | HID0_ICE)
 494 #define CONFIG_SYS_HID2 HID2_HBE
 495
 496 #define CONFIG_HIGH_BATS        1       /* High BATs supported */
 497
 498 #ifdef CONFIG_CMD_KGDB
 499 #define CONFIG_KGDB_BAUDRATE    230400  /* speed of kgdb serial port */
 500 #endif
 501
 502 /*
 503  * Environment Configuration
 504  */
 505 #define CONFIG_TIMESTAMP
 506
 507 #define CONFIG_HOSTNAME         mpc5121ads
 508 #define CONFIG_BOOTFILE         "mpc5121ads/uImage"
 509 #define CONFIG_ROOTPATH         "/opt/eldk/ppc_6xx"
 510
 511 #define CONFIG_LOADADDR         400000  /* default location for tftp and bootm */
 512
 513 #undef  CONFIG_BOOTARGS                 /* the boot command will set bootargs */
 514
 515 #define CONFIG_BAUDRATE         115200
 516
 517 #define CONFIG_PREBOOT  "echo;" \
 518         "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
 519         "echo"
 520
 521 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
 522         "u-boot_addr_r=200000\0"                                        \
 523         "kernel_addr_r=600000\0"                                        \
 524         "fdt_addr_r=880000\0"                                           \
 525         "ramdisk_addr_r=900000\0"                                       \
 526         "u-boot_addr=FFF00000\0"                                        \
 527         "kernel_addr=FFAC0000\0"                                        \
 528         "fdt_addr=FFEC0000\0"                                           \
 529         "ramdisk_addr=FEAC0000\0"                                       \
 530         "ramdiskfile=mpc5121ads/uRamdisk\0"                             \
 531         "u-boot=mpc5121ads/u-boot.bin\0"                                \
 532         "bootfile=mpc5121ads/uImage\0"                                  \
 533         "fdtfile=mpc5121ads/mpc5121ads.dtb\0"                           \
 534         "rootpath=/opt/eldk/ppc_6xx\n"                                  \
 535         "netdev=eth0\0"                                                 \
 536         "consdev=ttyPSC0\0"                                             \
 537         "nfsargs=setenv bootargs root=/dev/nfs rw "                     \
 538                 "nfsroot=${serverip}:${rootpath}\0"                     \
 539         "ramargs=setenv bootargs root=/dev/ram rw\0"                    \
 540         "addip=setenv bootargs ${bootargs} "                            \
 541                 "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"      \
 542                 ":${hostname}:${netdev}:off panic=1\0"                  \
 543         "addtty=setenv bootargs ${bootargs} "                           \
 544                 "console=${consdev},${baudrate}\0"                      \
 545         "flash_nfs=run nfsargs addip addtty;"                           \
 546                 "bootm ${kernel_addr} - ${fdt_addr}\0"                  \
 547         "flash_self=run ramargs addip addtty;"                          \
 548                 "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0"    \
 549         "net_nfs=tftp ${kernel_addr_r} ${bootfile};"                    \
 550                 "tftp ${fdt_addr_r} ${fdtfile};"                        \
 551                 "run nfsargs addip addtty;"                             \
 552                 "bootm ${kernel_addr_r} - ${fdt_addr_r}\0"              \
 553         "net_self=tftp ${kernel_addr_r} ${bootfile};"                   \
 554                 "tftp ${ramdisk_addr_r} ${ramdiskfile};"                \
 555                 "tftp ${fdt_addr_r} ${fdtfile};"                        \
 556                 "run ramargs addip addtty;"                             \
 557                 "bootm ${kernel_addr_r} ${ramdisk_addr_r} ${fdt_addr_r}\0"\
 558         "load=tftp ${u-boot_addr_r} ${u-boot}\0"                        \
 559         "update=protect off ${u-boot_addr} +${filesize};"               \
 560                 "era ${u-boot_addr} +${filesize};"                      \
 561                 "cp.b ${u-boot_addr_r} ${u-boot_addr} ${filesize}\0"    \
 562         "upd=run load update\0"                                         \
 563         ""
 564
 565 #define CONFIG_BOOTCOMMAND      "run flash_self"
 566
 567 #define CONFIG_OF_SUPPORT_OLD_DEVICE_TREES      1
 568
 569 #define OF_CPU                  "PowerPC,5121@0"
 570 #define OF_SOC_COMPAT           "fsl,mpc5121-immr"
 571 #define OF_TBCLK                (bd->bi_busfreq / 4)
 572 #define OF_STDOUT_PATH          "/soc@80000000/serial@11300"
 573
 574 /*-----------------------------------------------------------------------
 575  * IDE/ATA stuff
 576  *-----------------------------------------------------------------------
 577  */
 578
 579 #undef  CONFIG_IDE_8xx_PCCARD           /* Use IDE with PC Card Adapter */
 580 #undef  CONFIG_IDE_8xx_DIRECT           /* Direct IDE    not supported  */
 581 #undef  CONFIG_IDE_LED                  /* LED   for IDE not supported  */
 582
 583 #define CONFIG_IDE_RESET                /* reset for IDE supported      */
 584 #define CONFIG_IDE_PREINIT
 585
 586 #define CONFIG_SYS_IDE_MAXBUS           1       /* max. 1 IDE bus               */
 587 #define CONFIG_SYS_IDE_MAXDEVICE        2       /* max. 1 drive per IDE bus     */
 588
 589 #define CONFIG_SYS_ATA_IDE0_OFFSET      0x0000
 590 #define CONFIG_SYS_ATA_BASE_ADDR        get_pata_base()
 591
 592 /* Offset for data I/O                  RefMan MPC5121EE Table 28-10    */
 593 #define CONFIG_SYS_ATA_DATA_OFFSET      (0x00A0)
 594
 595 /* Offset for normal register accesses  */
 596 #define CONFIG_SYS_ATA_REG_OFFSET       (CONFIG_SYS_ATA_DATA_OFFSET)
 597
 598 /* Offset for alternate registers       RefMan MPC5121EE Table 28-23    */
 599 #define CONFIG_SYS_ATA_ALT_OFFSET       (0x00D8)
 600
 601 /* Interval between registers   */
 602 #define CONFIG_SYS_ATA_STRIDE           4
 603
 604 #define ATA_BASE_ADDR                   get_pata_base()
 605
 606 /*
 607  * Control register bit definitions
 608  */
 609 #define FSL_ATA_CTRL_FIFO_RST_B         0x80000000
 610 #define FSL_ATA_CTRL_ATA_RST_B          0x40000000
 611 #define FSL_ATA_CTRL_FIFO_TX_EN         0x20000000
 612 #define FSL_ATA_CTRL_FIFO_RCV_EN        0x10000000
 613 #define FSL_ATA_CTRL_DMA_PENDING        0x08000000
 614 #define FSL_ATA_CTRL_DMA_ULTRA          0x04000000
 615 #define FSL_ATA_CTRL_DMA_WRITE          0x02000000
 616 #define FSL_ATA_CTRL_IORDY_EN           0x01000000
 617
 618 #endif  /* __CONFIG_H */