include/configs/m28evk.h

   1 /*
   2  * Copyright (C) 2011 Marek Vasut <marek.vasut@gmail.com>
   3  * on behalf of DENX Software Engineering GmbH
   4  *
   5  * SPDX-License-Identifier:     GPL-2.0+
   6  */
   7 #ifndef __CONFIGS_M28EVK_H__
   8 #define __CONFIGS_M28EVK_H__
   9
  10 /* System configurations */
  11 #define CONFIG_MX28                             /* i.MX28 SoC */
  12 #define MACH_TYPE_M28EVK        3613
  13 #define CONFIG_MACH_TYPE        MACH_TYPE_M28EVK
  14
  15 #define CONFIG_FIT
  16
  17 #define CONFIG_TIMESTAMP                /* Print image info with timestamp */
  18
  19 /* U-Boot Commands */
  20 #define CONFIG_SYS_NO_FLASH
  21 #define CONFIG_DISPLAY_CPUINFO
  22 #define CONFIG_DOS_PARTITION
  23 #define CONFIG_FAT_WRITE
  24
  25 #define CONFIG_CMD_ASKENV
  26 #define CONFIG_CMD_BMP
  27 #define CONFIG_CMD_CACHE
  28 #define CONFIG_CMD_DATE
  29 #define CONFIG_CMD_DHCP
  30 #define CONFIG_CMD_EEPROM
  31 #define CONFIG_CMD_EXT4
  32 #define CONFIG_CMD_EXT4_WRITE
  33 #define CONFIG_CMD_FAT
  34 #define CONFIG_CMD_FS_GENERIC
  35 #define CONFIG_CMD_GREPENV
  36 #define CONFIG_CMD_I2C
  37 #define CONFIG_CMD_MII
  38 #define CONFIG_CMD_MMC
  39 #define CONFIG_CMD_NAND
  40 #define CONFIG_CMD_NAND_TRIMFFS
  41 #define CONFIG_CMD_PING
  42 #define CONFIG_CMD_SF
  43 #define CONFIG_CMD_SPI
  44 #define CONFIG_CMD_USB
  45 #define CONFIG_VIDEO
  46
  47
  48 /* Memory configuration */
  49 #define CONFIG_NR_DRAM_BANKS            1               /* 1 bank of DRAM */
  50 #define PHYS_SDRAM_1                    0x40000000      /* Base address */
  51 #define PHYS_SDRAM_1_SIZE               0x20000000      /* Max 512 MB RAM */
  52 #define CONFIG_SYS_SDRAM_BASE           PHYS_SDRAM_1
  53
  54 /* Environment */
  55 #define CONFIG_ENV_SIZE                 (16 * 1024)
  56 #define CONFIG_ENV_IS_IN_NAND
  57
  58 /* Environment is in NAND */
  59 #if defined(CONFIG_CMD_NAND) && defined(CONFIG_ENV_IS_IN_NAND)
  60 #define CONFIG_ENV_SIZE_REDUND          CONFIG_ENV_SIZE
  61 #define CONFIG_ENV_SECT_SIZE            (128 * 1024)
  62 #define CONFIG_ENV_RANGE                (4 * CONFIG_ENV_SECT_SIZE)
  63 #define CONFIG_ENV_OFFSET               (24 * CONFIG_ENV_SECT_SIZE) /* 3 MiB */
  64 #define CONFIG_ENV_OFFSET_REDUND        \
  65                 (CONFIG_ENV_OFFSET + CONFIG_ENV_RANGE)
  66
  67 #define CONFIG_CMD_UBI
  68 #define CONFIG_CMD_UBIFS
  69 #define CONFIG_CMD_MTDPARTS
  70 #define CONFIG_RBTREE
  71 #define CONFIG_LZO
  72 #define CONFIG_MTD_DEVICE
  73 #define CONFIG_MTD_PARTITIONS
  74 #define MTDIDS_DEFAULT                  "nand0=gpmi-nand"
  75 #define MTDPARTS_DEFAULT                        \
  76         "mtdparts=gpmi-nand:"                   \
  77                 "3m(u-boot),"                   \
  78                 "512k(env1),"                   \
  79                 "512k(env2),"                   \
  80                 "14m(boot),"                    \
  81                 "238m(data),"                   \
  82                 "-@4096k(UBI)"
  83 #else
  84 #define CONFIG_ENV_IS_NOWHERE
  85 #endif
  86
  87 /* FEC Ethernet on SoC */
  88 #ifdef CONFIG_CMD_NET
  89 #define CONFIG_FEC_MXC
  90 #endif
  91
  92 /* EEPROM */
  93 #ifdef CONFIG_CMD_EEPROM
  94 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN  2
  95 #endif
  96
  97 /* RTC */
  98 #ifdef CONFIG_CMD_DATE
  99 /* Use the internal RTC in the MXS chip */
 100 #define CONFIG_RTC_INTERNAL
 101 #ifdef CONFIG_RTC_INTERNAL
 102 #define CONFIG_RTC_MXS
 103 #else
 104 #define CONFIG_RTC_M41T62
 105 #define CONFIG_SYS_I2C_RTC_ADDR         0x68
 106 #define CONFIG_SYS_M41T11_BASE_YEAR     2000
 107 #endif
 108 #endif
 109
 110 /* USB */
 111 #ifdef CONFIG_CMD_USB
 112 #define CONFIG_EHCI_MXS_PORT0
 113 #define CONFIG_EHCI_MXS_PORT1
 114 #define CONFIG_USB_MAX_CONTROLLER_COUNT 2
 115 #define CONFIG_USB_STORAGE
 116 #endif
 117
 118 /* SPI */
 119 #ifdef CONFIG_CMD_SPI
 120 #define CONFIG_DEFAULT_SPI_BUS          2
 121 #define CONFIG_DEFAULT_SPI_CS           0
 122 #define CONFIG_DEFAULT_SPI_MODE         SPI_MODE_0
 123
 124 /* SPI FLASH */
 125 #ifdef CONFIG_CMD_SF
 126 #define CONFIG_SF_DEFAULT_BUS           2
 127 #define CONFIG_SF_DEFAULT_CS            0
 128 #define CONFIG_SF_DEFAULT_SPEED         40000000
 129 #define CONFIG_SF_DEFAULT_MODE          SPI_MODE_0
 130
 131 #define CONFIG_ENV_SPI_BUS              2
 132 #define CONFIG_ENV_SPI_CS               0
 133 #define CONFIG_ENV_SPI_MAX_HZ           40000000
 134 #define CONFIG_ENV_SPI_MODE             SPI_MODE_0
 135 #endif
 136
 137 #endif
 138
 139 /* LCD */
 140 #ifdef CONFIG_VIDEO
 141 #define CONFIG_VIDEO_LOGO
 142 #define CONFIG_SPLASH_SCREEN
 143 #define CONFIG_CMD_BMP
 144 #define CONFIG_BMP_16BPP
 145 #define CONFIG_VIDEO_BMP_RLE8
 146 #define CONFIG_VIDEO_BMP_GZIP
 147 #define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE  (2 << 20)
 148 #endif
 149
 150 /* Booting Linux */
 151 #define CONFIG_BOOTDELAY        3
 152 #define CONFIG_BOOTFILE         "fitImage"
 153 #define CONFIG_BOOTARGS         "console=ttyAMA0,115200n8 "
 154 #define CONFIG_BOOTCOMMAND      "run mmc_mmc"
 155 #define CONFIG_LOADADDR         0x42000000
 156 #define CONFIG_SYS_LOAD_ADDR    CONFIG_LOADADDR
 157
 158 /* Extra Environment */
 159 #define CONFIG_PREBOOT          "run try_bootscript"
 160 #define CONFIG_HOSTNAME         m28evk
 161
 162 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
 163         "consdev=ttyAMA0\0"                                             \
 164         "baudrate=115200\0"                                             \
 165         "bootscript=boot.scr\0"                                         \
 166         "bootdev=/dev/mmcblk0p2\0"                                      \
 167         "rootdev=/dev/mmcblk0p3\0"                                      \
 168         "netdev=eth0\0"                                                 \
 169         "hostname=m28evk\0"                                             \
 170         "rootpath=/opt/eldk-5.5/armv5te/rootfs-qte-sdk\0"               \
 171         "kernel_addr_r=0x42000000\0"                                    \
 172         "videomode=video=ctfb:x:800,y:480,depth:18,mode:0,pclk:30066,"  \
 173                 "le:0,ri:256,up:0,lo:45,hs:1,vs:1,sync:100663296,"      \
 174                 "vmode:0\0"                                             \
 175         "update_nand_full_filename=u-boot.nand\0"                       \
 176         "update_nand_firmware_filename=u-boot.sb\0"                     \
 177         "update_sd_firmware_filename=u-boot.sd\0"                       \
 178         "update_nand_firmware_maxsz=0x100000\0"                         \
 179         "update_nand_stride=0x40\0"     /* MX28 datasheet ch. 12.12 */  \
 180         "update_nand_count=0x4\0"       /* MX28 datasheet ch. 12.12 */  \
 181         "update_nand_get_fcb_size="     /* Get size of FCB blocks */    \
 182                 "nand device 0 ; "                                      \
 183                 "nand info ; "                                          \
 184                 "setexpr fcb_sz ${update_nand_stride} * ${update_nand_count};" \
 185                 "setexpr update_nand_fcb ${fcb_sz} * ${nand_writesize}\0" \
 186         "update_nand_full="             /* Update FCB, DBBT and FW */   \
 187                 "if tftp ${update_nand_full_filename} ; then "          \
 188                 "run update_nand_get_fcb_size ; "                       \
 189                 "nand scrub -y 0x0 ${filesize} ; "                      \
 190                 "nand write.raw ${loadaddr} 0x0 ${fcb_sz} ; "           \
 191                 "setexpr update_off ${loadaddr} + ${update_nand_fcb} ; " \
 192                 "setexpr update_sz ${filesize} - ${update_nand_fcb} ; " \
 193                 "nand write ${update_off} ${update_nand_fcb} ${update_sz} ; " \
 194                 "fi\0"                                                  \
 195         "update_nand_firmware="         /* Update only firmware */      \
 196                 "if tftp ${update_nand_firmware_filename} ; then "      \
 197                 "run update_nand_get_fcb_size ; "                       \
 198                 "setexpr fcb_sz ${update_nand_fcb} * 2 ; " /* FCB + DBBT */ \
 199                 "setexpr fw_sz ${update_nand_firmware_maxsz} * 2 ; "    \
 200                 "setexpr fw_off ${fcb_sz} + ${update_nand_firmware_maxsz};" \
 201                 "nand erase ${fcb_sz} ${fw_sz} ; "                      \
 202                 "nand write ${loadaddr} ${fcb_sz} ${filesize} ; "       \
 203                 "nand write ${loadaddr} ${fw_off} ${filesize} ; "       \
 204                 "fi\0"                                                  \
 205         "update_sd_firmware="           /* Update the SD firmware partition */ \
 206                 "if mmc rescan ; then "                                 \
 207                 "if tftp ${update_sd_firmware_filename} ; then "        \
 208                 "setexpr fw_sz ${filesize} / 0x200 ; "  /* SD block size */ \
 209                 "setexpr fw_sz ${fw_sz} + 1 ; "                         \
 210                 "mmc write ${loadaddr} 0x800 ${fw_sz} ; "               \
 211                 "fi ; "                                                 \
 212                 "fi\0"                                                  \
 213         "addcons="                                                      \
 214                 "setenv bootargs ${bootargs} "                          \
 215                 "console=${consdev},${baudrate}\0"                      \
 216         "addip="                                                        \
 217                 "setenv bootargs ${bootargs} "                          \
 218                 "ip=${ipaddr}:${serverip}:${gatewayip}:"                \
 219                         "${netmask}:${hostname}:${netdev}:off\0"        \
 220         "addmisc="                                                      \
 221                 "setenv bootargs ${bootargs} ${miscargs}\0"             \
 222         "adddfltmtd="                                                   \
 223                 "if test \"x${mtdparts}\" == \"x\" ; then "             \
 224                         "mtdparts default ; "                           \
 225                 "fi\0"                                                  \
 226         "addmtd="                                                       \
 227                 "run adddfltmtd ; "                                     \
 228                 "setenv bootargs ${bootargs} ${mtdparts}\0"             \
 229         "addargs=run addcons addmtd addmisc\0"                          \
 230         "mmcload="                                                      \
 231                 "mmc rescan ; "                                         \
 232                 "load mmc 0:2 ${kernel_addr_r} ${bootfile}\0"           \
 233         "ubiload="                                                      \
 234                 "ubi part UBI ; ubifsmount ubi0:rootfs ; "              \
 235                 "ubifsload ${kernel_addr_r} /boot/${bootfile}\0"        \
 236         "netload="                                                      \
 237                 "tftp ${kernel_addr_r} ${hostname}/${bootfile}\0"       \
 238         "miscargs=nohlt panic=1\0"                                      \
 239         "mmcargs=setenv bootargs root=${rootdev} rw rootwait\0"         \
 240         "ubiargs="                                                      \
 241                 "setenv bootargs ubi.mtd=5 "                            \
 242                 "root=ubi0:rootfs rootfstype=ubifs\0"                   \
 243         "nfsargs="                                                      \
 244                 "setenv bootargs root=/dev/nfs rw "                     \
 245                         "nfsroot=${serverip}:${rootpath},v3,tcp\0"      \
 246         "mmc_mmc="                                                      \
 247                 "run mmcload mmcargs addargs ; "                        \
 248                 "bootm ${kernel_addr_r}\0"                              \
 249         "mmc_ubi="                                                      \
 250                 "run mmcload ubiargs addargs ; "                        \
 251                 "bootm ${kernel_addr_r}\0"                              \
 252         "mmc_nfs="                                                      \
 253                 "run mmcload nfsargs addip addargs ; "                  \
 254                 "bootm ${kernel_addr_r}\0"                              \
 255         "ubi_mmc="                                                      \
 256                 "run ubiload mmcargs addargs ; "                        \
 257                 "bootm ${kernel_addr_r}\0"                              \
 258         "ubi_ubi="                                                      \
 259                 "run ubiload ubiargs addargs ; "                        \
 260                 "bootm ${kernel_addr_r}\0"                              \
 261         "ubi_nfs="                                                      \
 262                 "run ubiload nfsargs addip addargs ; "                  \
 263                 "bootm ${kernel_addr_r}\0"                              \
 264         "net_mmc="                                                      \
 265                 "run netload mmcargs addargs ; "                        \
 266                 "bootm ${kernel_addr_r}\0"                              \
 267         "net_ubi="                                                      \
 268                 "run netload ubiargs addargs ; "                        \
 269                 "bootm ${kernel_addr_r}\0"                              \
 270         "net_nfs="                                                      \
 271                 "run netload nfsargs addip addargs ; "                  \
 272                 "bootm ${kernel_addr_r}\0"                              \
 273         "try_bootscript="                                               \
 274                 "mmc rescan;"                                           \
 275                 "if test -e mmc 0:2 ${bootscript} ; then "              \
 276                 "if load mmc 0:2 ${kernel_addr_r} ${bootscript};"       \
 277                 "then ; "                                               \
 278                         "echo Running bootscript... ; "                 \
 279                         "source ${kernel_addr_r} ; "                    \
 280                 "fi ; "                                                 \
 281                 "fi\0"
 282
 283 /* The rest of the configuration is shared */
 284 #include <configs/mxs.h>
 285
 286 #endif /* __CONFIGS_M28EVK_H__ */