include/configs/lx2160ardb.h

   1 /* SPDX-License-Identifier: GPL-2.0+ */
   2 /*
   3  * Copyright 2018,2020 NXP
   4  */
   5
   6 #ifndef __LX2_RDB_H
   7 #define __LX2_RDB_H
   8
   9 #include "lx2160a_common.h"
  10
  11 /* Qixis */
  12 #define QIXIS_XMAP_MASK                 0x07
  13 #define QIXIS_XMAP_SHIFT                5
  14 #define QIXIS_RST_CTL_RESET_EN          0x30
  15 #define QIXIS_LBMAP_DFLTBANK            0x00
  16 #define QIXIS_LBMAP_ALTBANK             0x20
  17 #define QIXIS_LBMAP_QSPI                0x00
  18 #define QIXIS_RCW_SRC_QSPI              0xff
  19 #define QIXIS_RST_CTL_RESET             0x31
  20 #define QIXIS_RCFG_CTL_RECONFIG_IDLE    0x20
  21 #define QIXIS_RCFG_CTL_RECONFIG_START   0x21
  22 #define QIXIS_RCFG_CTL_WATCHDOG_ENBLE   0x08
  23 #define QIXIS_LBMAP_MASK                0x0f
  24 #define QIXIS_LBMAP_SD
  25 #define QIXIS_LBMAP_EMMC
  26 #define QIXIS_RCW_SRC_SD           0x08
  27 #define QIXIS_RCW_SRC_EMMC         0x09
  28 #define NON_EXTENDED_DUTCFG
  29
  30 /* VID */
  31
  32 #define I2C_MUX_CH_VOL_MONITOR          0xA
  33 /* Voltage monitor on channel 2*/
  34 #define I2C_VOL_MONITOR_ADDR            0x63
  35 #define I2C_VOL_MONITOR_BUS_V_OFFSET    0x2
  36 #define I2C_VOL_MONITOR_BUS_V_OVF       0x1
  37 #define I2C_VOL_MONITOR_BUS_V_SHIFT     3
  38 #define CONFIG_VID_FLS_ENV              "lx2160ardb_vdd_mv"
  39 #define CONFIG_VID
  40
  41 /* The lowest and highest voltage allowed*/
  42 #define VDD_MV_MIN                      775
  43 #define VDD_MV_MAX                      855
  44
  45 /* PM Bus commands code for LTC3882*/
  46 #define PMBUS_CMD_PAGE                  0x0
  47 #define PMBUS_CMD_READ_VOUT             0x8B
  48 #define PMBUS_CMD_PAGE_PLUS_WRITE       0x05
  49 #define PMBUS_CMD_VOUT_COMMAND          0x21
  50 #define PWM_CHANNEL0                    0x0
  51
  52 #define CONFIG_VOL_MONITOR_LTC3882_SET
  53 #define CONFIG_VOL_MONITOR_LTC3882_READ
  54
  55 /* RTC */
  56 #define CONFIG_SYS_RTC_BUS_NUM          4
  57
  58 /* MAC/PHY configuration */
  59 #if defined(CONFIG_FSL_MC_ENET)
  60 #define CONFIG_MII
  61 #define CONFIG_ETHPRIME         "DPMAC1@xgmii"
  62
  63 #define AQR107_PHY_ADDR1        0x04
  64 #define AQR107_PHY_ADDR2        0x05
  65 #define AQR107_IRQ_MASK         0x0C
  66
  67 #define CORTINA_NO_FW_UPLOAD
  68 #define CORTINA_PHY_ADDR1       0x0
  69 #define INPHI_PHY_ADDR1         0x0
  70
  71 #define RGMII_PHY_ADDR1         0x01
  72 #define RGMII_PHY_ADDR2         0x02
  73
  74 #endif
  75
  76 /* EMC2305 */
  77 #define I2C_MUX_CH_EMC2305              0x09
  78 #define I2C_EMC2305_ADDR                0x4D
  79 #define I2C_EMC2305_CMD         0x40
  80 #define I2C_EMC2305_PWM         0x80
  81
  82 /* EEPROM */
  83 #define CONFIG_ID_EEPROM
  84 #define CONFIG_SYS_I2C_EEPROM_NXID
  85 #define CONFIG_SYS_EEPROM_BUS_NUM                  0
  86 #define CONFIG_SYS_I2C_EEPROM_ADDR                 0x57
  87 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN      1
  88 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS     3
  89 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
  90
  91 /* Initial environment variables */
  92 #define CONFIG_EXTRA_ENV_SETTINGS               \
  93         EXTRA_ENV_SETTINGS                      \
  94         "boot_scripts=lx2160ardb_boot.scr\0"    \
  95         "boot_script_hdr=hdr_lx2160ardb_bs.out\0"       \
  96         "BOARD=lx2160ardb\0"                    \
  97         "xspi_bootcmd=echo Trying load from flexspi..;"         \
  98                 "sf probe 0:0 && sf read $load_addr "           \
  99                 "$kernel_start $kernel_size ; env exists secureboot &&" \
 100                 "sf read $kernelheader_addr_r $kernelheader_start "     \
 101                 "$kernelheader_size && esbc_validate ${kernelheader_addr_r}; "\
 102                 " bootm $load_addr#$BOARD\0"                    \
 103         "sd_bootcmd=echo Trying load from sd card..;"           \
 104                 "mmcinfo; mmc read $load_addr "                 \
 105                 "$kernel_addr_sd $kernel_size_sd ;"             \
 106                 "env exists secureboot && mmc read $kernelheader_addr_r "\
 107                 "$kernelhdr_addr_sd $kernelhdr_size_sd "        \
 108                 " && esbc_validate ${kernelheader_addr_r};"     \
 109                 "bootm $load_addr#$BOARD\0"                     \
 110         "sd2_bootcmd=echo Trying load from emmc card..;"        \
 111                 "mmc dev 1; mmcinfo; mmc read $load_addr "      \
 112                 "$kernel_addr_sd $kernel_size_sd ;"             \
 113                 "env exists secureboot && mmc read $kernelheader_addr_r "\
 114                 "$kernelhdr_addr_sd $kernelhdr_size_sd "        \
 115                 " && esbc_validate ${kernelheader_addr_r};"     \
 116                 "bootm $load_addr#$BOARD\0"
 117
 118 #include <asm/fsl_secure_boot.h>
 119
 120 #endif /* __LX2_RDB_H */