include/configs/lx2160a_common.h

   1 /* SPDX-License-Identifier: GPL-2.0+ */
   2 /*
   3  * Copyright 2018-2021 NXP
   4  */
   5
   6 #ifndef __LX2_COMMON_H
   7 #define __LX2_COMMON_H
   8
   9 #include <asm/arch/stream_id_lsch3.h>
  10 #include <asm/arch/config.h>
  11 #include <asm/arch/soc.h>
  12
  13 #define CONFIG_REMAKE_ELF
  14 #define CONFIG_FSL_TZPC_BP147
  15 #define CONFIG_FSL_MEMAC
  16
  17 #define CONFIG_SYS_INIT_SP_ADDR         CONFIG_SYS_TEXT_BASE
  18 #define CONFIG_SYS_FLASH_BASE           0x20000000
  19
  20 /* DDR */
  21 #define CONFIG_SYS_FSL_DDR_INTLV_256B   /* force 256 byte interleaving */
  22 #define CONFIG_VERY_BIG_RAM
  23 #define CONFIG_SYS_DDR_SDRAM_BASE               0x80000000UL
  24 #define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY       0
  25 #define CONFIG_SYS_DDR_BLOCK2_BASE              0x2080000000ULL
  26 #define CONFIG_SYS_FSL_DDR_MAIN_NUM_CTRLS       2
  27 #define CONFIG_SYS_SDRAM_SIZE                   0x200000000UL
  28 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE
  29 #define CONFIG_MEM_INIT_VALUE           0xdeadbeef
  30 #define SPD_EEPROM_ADDRESS1             0x51
  31 #define SPD_EEPROM_ADDRESS2             0x52
  32 #define SPD_EEPROM_ADDRESS3             0x53
  33 #define SPD_EEPROM_ADDRESS4             0x54
  34 #define SPD_EEPROM_ADDRESS5             0x55
  35 #define SPD_EEPROM_ADDRESS6             0x56
  36 #define SPD_EEPROM_ADDRESS              SPD_EEPROM_ADDRESS1
  37 #define CONFIG_SYS_SPD_BUS_NUM          0       /* SPD on I2C bus 0 */
  38 #define CONFIG_DIMM_SLOTS_PER_CTLR      2
  39 #define CONFIG_CHIP_SELECTS_PER_CTRL    4
  40 #define CONFIG_SYS_MONITOR_LEN          (936 * 1024)
  41
  42 /* Miscellaneous configurable options */
  43
  44 /* SMP Definitinos  */
  45 #define CPU_RELEASE_ADDR                secondary_boot_addr
  46
  47 /* Generic Timer Definitions */
  48 /*
  49  * This is not an accurate number. It is used in start.S. The frequency
  50  * will be udpated later when get_bus_freq(0) is available.
  51  */
  52
  53 #define COUNTER_FREQUENCY               25000000        /* 25MHz */
  54
  55 /* Serial Port */
  56 #define CONFIG_PL011_CLOCK              (get_bus_freq(0) / 4)
  57 #define CONFIG_SYS_SERIAL0              0x21c0000
  58 #define CONFIG_SYS_SERIAL1              0x21d0000
  59 #define CONFIG_SYS_SERIAL2              0x21e0000
  60 #define CONFIG_SYS_SERIAL3              0x21f0000
  61 /*below might needs to be removed*/
  62 #define CONFIG_PL01x_PORTS              {(void *)CONFIG_SYS_SERIAL0, \
  63                                         (void *)CONFIG_SYS_SERIAL1, \
  64                                         (void *)CONFIG_SYS_SERIAL2, \
  65                                         (void *)CONFIG_SYS_SERIAL3 }
  66
  67 /* MC firmware */
  68 #define CONFIG_SYS_LS_MC_DPC_MAX_LENGTH         0x20000
  69 #define CONFIG_SYS_LS_MC_DRAM_DPC_OFFSET        0x00F00000
  70 #define CONFIG_SYS_LS_MC_DPL_MAX_LENGTH         0x20000
  71 #define CONFIG_SYS_LS_MC_DRAM_DPL_OFFSET        0x00F20000
  72 #define CONFIG_SYS_LS_MC_BOOT_TIMEOUT_MS        5000
  73
  74 /* Define phy_reset function to boot the MC based on mcinitcmd.
  75  * This happens late enough to properly fixup u-boot env MAC addresses.
  76  */
  77 #define CONFIG_RESET_PHY_R
  78
  79 /*
  80  * Carve out a DDR region which will not be used by u-boot/Linux
  81  *
  82  * It will be used by MC and Debug Server. The MC region must be
  83  * 512MB aligned, so the min size to hide is 512MB.
  84  */
  85 #ifdef CONFIG_FSL_MC_ENET
  86 #define CONFIG_SYS_LS_MC_DRAM_BLOCK_MIN_SIZE    (256UL * 1024 * 1024)
  87 #endif
  88
  89 /* I2C bus multiplexer */
  90 #define I2C_MUX_PCA_ADDR_PRI            0x77 /* Primary Mux*/
  91 #define I2C_MUX_CH_DEFAULT              0x8
  92
  93 /* RTC */
  94 #define RTC
  95 #define CONFIG_SYS_I2C_RTC_ADDR         0x51  /* Channel 3*/
  96
  97 /* EEPROM */
  98 #define CONFIG_SYS_I2C_EEPROM_NXID
  99 #define CONFIG_SYS_EEPROM_BUS_NUM               0
 100
 101 /* Qixis */
 102 #define CONFIG_FSL_QIXIS
 103 #define CONFIG_QIXIS_I2C_ACCESS
 104 #define CONFIG_SYS_I2C_FPGA_ADDR                0x66
 105
 106 /* PCI */
 107 #ifdef CONFIG_PCI
 108 #define CONFIG_SYS_PCI_64BIT
 109 #define CONFIG_PCI_SCAN_SHOW
 110 #endif
 111
 112 /* SATA */
 113
 114 #ifdef CONFIG_SCSI
 115 #define CONFIG_SCSI_AHCI_PLAT
 116 #define CONFIG_SYS_SATA1                AHCI_BASE_ADDR1
 117 #define CONFIG_SYS_SATA2                AHCI_BASE_ADDR2
 118 #define CONFIG_SYS_SCSI_MAX_SCSI_ID     1
 119 #define CONFIG_SYS_SCSI_MAX_LUN         1
 120 #define CONFIG_SYS_SCSI_MAX_DEVICE      (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
 121                                         CONFIG_SYS_SCSI_MAX_LUN)
 122 #endif
 123
 124 /* USB */
 125 #ifdef CONFIG_USB_HOST
 126 #ifndef CONFIG_TARGET_LX2162AQDS
 127 #define CONFIG_USB_MAX_CONTROLLER_COUNT 2
 128 #endif
 129 #endif
 130
 131 /* GPIO */
 132 #ifdef CONFIG_DM_GPIO
 133 #ifndef CONFIG_MPC8XXX_GPIO
 134 #define CONFIG_MPC8XXX_GPIO
 135 #endif
 136 #endif
 137
 138 #ifndef __ASSEMBLY__
 139 unsigned long get_board_sys_clk(void);
 140 #endif
 141
 142 #define CONFIG_SYS_CLK_FREQ             get_board_sys_clk()
 143 #define COUNTER_FREQUENCY_REAL          (CONFIG_SYS_CLK_FREQ / 4)
 144
 145 #define CONFIG_HWCONFIG
 146 #define HWCONFIG_BUFFER_SIZE            128
 147
 148 /* Monitor Command Prompt */
 149 #define CONFIG_SYS_CBSIZE               512     /* Console I/O Buffer Size */
 150 #define CONFIG_SYS_PBSIZE               (CONFIG_SYS_CBSIZE + \
 151                                         sizeof(CONFIG_SYS_PROMPT) + 16)
 152 #define CONFIG_SYS_BARGSIZE             CONFIG_SYS_CBSIZE /* Boot args buffer */
 153 #define CONFIG_SYS_MAXARGS              64      /* max command args */
 154
 155 #define CONFIG_SYS_BOOTM_LEN   (64 << 20)      /* Increase max gunzip size */
 156
 157 /* Initial environment variables */
 158 #define XSPI_MC_INIT_CMD                                \
 159         "sf probe 0:0 && "                              \
 160         "sf read 0x80640000 0x640000 0x80000 && "       \
 161         "sf read $fdt_addr_r 0xf00000 0x100000 && "     \
 162         "env exists secureboot && "                     \
 163         "esbc_validate 0x80640000 && "                  \
 164         "esbc_validate 0x80680000; "                    \
 165         "sf read 0x80a00000 0xa00000 0x300000 && "      \
 166         "sf read 0x80e00000 0xe00000 0x100000; "        \
 167         "fsl_mc start mc 0x80a00000 0x80e00000\0"
 168
 169 #define SD_MC_INIT_CMD                          \
 170         "mmc read 0x80a00000 0x5000 0x1200;"    \
 171         "mmc read 0x80e00000 0x7000 0x800;"     \
 172         "mmc read $fdt_addr_r 0x7800 0x800;"    \
 173         "env exists secureboot && "             \
 174         "mmc read 0x80640000 0x3200 0x20 && "   \
 175         "mmc read 0x80680000 0x3400 0x20 && "   \
 176         "esbc_validate 0x80640000 && "          \
 177         "esbc_validate 0x80680000 ;"            \
 178         "fsl_mc start mc 0x80a00000 0x80e00000\0"
 179
 180 #define SD2_MC_INIT_CMD                         \
 181         "mmc dev 1; mmc read 0x80a00000 0x5000 0x1200;" \
 182         "mmc read 0x80e00000 0x7000 0x800;"     \
 183         "mmc read $fdt_addr_r 0x7800 0x800;"    \
 184         "env exists secureboot && "             \
 185         "mmc read 0x80640000 0x3200 0x20 && "   \
 186         "mmc read 0x80680000 0x3400 0x20 && "   \
 187         "esbc_validate 0x80640000 && "          \
 188         "esbc_validate 0x80680000 ;"            \
 189         "fsl_mc start mc 0x80a00000 0x80e00000\0"
 190
 191 #define EXTRA_ENV_SETTINGS                      \
 192         "hwconfig=fsl_ddr:bank_intlv=auto\0"    \
 193         "ramdisk_addr=0x800000\0"               \
 194         "ramdisk_size=0x2000000\0"              \
 195         "fdt_high=0xa0000000\0"                 \
 196         "initrd_high=0xffffffffffffffff\0"      \
 197         "fdt_addr=0x64f00000\0"                 \
 198         "kernel_start=0x1000000\0"              \
 199         "kernelheader_start=0x600000\0"         \
 200         "scriptaddr=0x80000000\0"               \
 201         "scripthdraddr=0x80080000\0"            \
 202         "fdtheader_addr_r=0x80100000\0"         \
 203         "kernelheader_addr_r=0x80200000\0"      \
 204         "kernel_addr_r=0x81000000\0"            \
 205         "kernelheader_size=0x40000\0"           \
 206         "fdt_addr_r=0x90000000\0"               \
 207         "load_addr=0xa0000000\0"                \
 208         "kernel_size=0x2800000\0"               \
 209         "kernel_addr_sd=0x8000\0"               \
 210         "kernelhdr_addr_sd=0x3000\0"            \
 211         "kernel_size_sd=0x14000\0"              \
 212         "kernelhdr_size_sd=0x20\0"              \
 213         "console=ttyAMA0,38400n8\0"             \
 214         BOOTENV                                 \
 215         "mcmemsize=0x70000000\0"                \
 216         XSPI_MC_INIT_CMD                                \
 217         "scan_dev_for_boot_part="               \
 218                 "part list ${devtype} ${devnum} devplist; "     \
 219                 "env exists devplist || setenv devplist 1; "    \
 220                 "for distro_bootpart in ${devplist}; do "       \
 221                         "if fstype ${devtype} "                 \
 222                                 "${devnum}:${distro_bootpart} " \
 223                                 "bootfstype; then "             \
 224                                 "run scan_dev_for_boot; "       \
 225                         "fi; "                                  \
 226                 "done\0"                                        \
 227         "boot_a_script="                                        \
 228                 "load ${devtype} ${devnum}:${distro_bootpart} " \
 229                         "${scriptaddr} ${prefix}${script}; "    \
 230                 "env exists secureboot && load ${devtype} "     \
 231                         "${devnum}:${distro_bootpart} "         \
 232                         "${scripthdraddr} ${prefix}${boot_script_hdr} " \
 233                         "&& esbc_validate ${scripthdraddr};"    \
 234                 "source ${scriptaddr}\0"
 235
 236 #define XSPI_NOR_BOOTCOMMAND                                            \
 237                         "sf probe 0:0; "                                \
 238                         "sf read 0x806c0000 0x6c0000 0x40000; "         \
 239                         "env exists mcinitcmd && env exists secureboot" \
 240                         " && esbc_validate 0x806c0000; "                \
 241                         "sf read 0x80d00000 0xd00000 0x100000; "        \
 242                         "env exists mcinitcmd && "                      \
 243                         "fsl_mc lazyapply dpl 0x80d00000; "             \
 244                         "run distro_bootcmd;run xspi_bootcmd; "         \
 245                         "env exists secureboot && esbc_halt;"
 246
 247 #define SD_BOOTCOMMAND                                          \
 248                 "env exists mcinitcmd && mmcinfo; "             \
 249                 "mmc read 0x80d00000 0x6800 0x800; "            \
 250                 "env exists mcinitcmd && env exists secureboot "        \
 251                 " && mmc read 0x806C0000 0x3600 0x20 "          \
 252                 "&& esbc_validate 0x806C0000;env exists mcinitcmd "     \
 253                 "&& fsl_mc lazyapply dpl 0x80d00000;"           \
 254                 "run distro_bootcmd;run sd_bootcmd;"            \
 255                 "env exists secureboot && esbc_halt;"
 256
 257 #define SD2_BOOTCOMMAND                                         \
 258                 "mmc dev 1; env exists mcinitcmd && mmcinfo; "  \
 259                 "mmc read 0x80d00000 0x6800 0x800; "            \
 260                 "env exists mcinitcmd && env exists secureboot "        \
 261                 " && mmc read 0x806C0000 0x3600 0x20 "          \
 262                 "&& esbc_validate 0x806C0000;env exists mcinitcmd "     \
 263                 "&& fsl_mc lazyapply dpl 0x80d00000;"           \
 264                 "run distro_bootcmd;run sd2_bootcmd;"           \
 265                 "env exists secureboot && esbc_halt;"
 266
 267 #define BOOT_TARGET_DEVICES(func) \
 268         func(USB, usb, 0) \
 269         func(MMC, mmc, 0) \
 270         func(MMC, mmc, 1) \
 271         func(SCSI, scsi, 0) \
 272         func(DHCP, dhcp, na)
 273 #include <config_distro_bootcmd.h>
 274
 275 #endif /* __LX2_COMMON_H */