include/configs/lx2160a_common.h

   1 /* SPDX-License-Identifier: GPL-2.0+ */
   2 /*
   3  * Copyright 2018-2021 NXP
   4  */
   5
   6 #ifndef __LX2_COMMON_H
   7 #define __LX2_COMMON_H
   8
   9 #include <asm/arch/stream_id_lsch3.h>
  10 #include <asm/arch/config.h>
  11 #include <asm/arch/soc.h>
  12
  13 #define CONFIG_FSL_MEMAC
  14
  15 #define CONFIG_SYS_FLASH_BASE           0x20000000
  16
  17 /* DDR */
  18 #define CONFIG_SYS_FSL_DDR_INTLV_256B   /* force 256 byte interleaving */
  19 #define CONFIG_VERY_BIG_RAM
  20 #define CONFIG_SYS_DDR_SDRAM_BASE               0x80000000UL
  21 #define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY       0
  22 #define CONFIG_SYS_DDR_BLOCK2_BASE              0x2080000000ULL
  23 #define CONFIG_SYS_FSL_DDR_MAIN_NUM_CTRLS       2
  24 #define CONFIG_SYS_SDRAM_SIZE                   0x200000000UL
  25 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE
  26 #define CONFIG_MEM_INIT_VALUE           0xdeadbeef
  27 #define SPD_EEPROM_ADDRESS1             0x51
  28 #define SPD_EEPROM_ADDRESS2             0x52
  29 #define SPD_EEPROM_ADDRESS3             0x53
  30 #define SPD_EEPROM_ADDRESS4             0x54
  31 #define SPD_EEPROM_ADDRESS5             0x55
  32 #define SPD_EEPROM_ADDRESS6             0x56
  33 #define SPD_EEPROM_ADDRESS              SPD_EEPROM_ADDRESS1
  34 #define CONFIG_SYS_MONITOR_LEN          (936 * 1024)
  35
  36 /* Miscellaneous configurable options */
  37
  38 /* SMP Definitinos  */
  39 #define CPU_RELEASE_ADDR                secondary_boot_addr
  40
  41 /* Generic Timer Definitions */
  42 /*
  43  * This is not an accurate number. It is used in start.S. The frequency
  44  * will be udpated later when get_bus_freq(0) is available.
  45  */
  46
  47
  48 /* Serial Port */
  49 #define CONFIG_PL011_CLOCK              (get_bus_freq(0) / 4)
  50 #define CONFIG_SYS_SERIAL0              0x21c0000
  51 #define CONFIG_SYS_SERIAL1              0x21d0000
  52 #define CONFIG_SYS_SERIAL2              0x21e0000
  53 #define CONFIG_SYS_SERIAL3              0x21f0000
  54 /*below might needs to be removed*/
  55 #define CONFIG_PL01x_PORTS              {(void *)CONFIG_SYS_SERIAL0, \
  56                                         (void *)CONFIG_SYS_SERIAL1, \
  57                                         (void *)CONFIG_SYS_SERIAL2, \
  58                                         (void *)CONFIG_SYS_SERIAL3 }
  59
  60 /* MC firmware */
  61 #define CONFIG_SYS_LS_MC_DPC_MAX_LENGTH         0x20000
  62 #define CONFIG_SYS_LS_MC_DRAM_DPC_OFFSET        0x00F00000
  63 #define CONFIG_SYS_LS_MC_DPL_MAX_LENGTH         0x20000
  64 #define CONFIG_SYS_LS_MC_DRAM_DPL_OFFSET        0x00F20000
  65 #define CONFIG_SYS_LS_MC_BOOT_TIMEOUT_MS        5000
  66
  67 /*
  68  * Carve out a DDR region which will not be used by u-boot/Linux
  69  *
  70  * It will be used by MC and Debug Server. The MC region must be
  71  * 512MB aligned, so the min size to hide is 512MB.
  72  */
  73 #ifdef CONFIG_FSL_MC_ENET
  74 #define CONFIG_SYS_LS_MC_DRAM_BLOCK_MIN_SIZE    (256UL * 1024 * 1024)
  75 #endif
  76
  77 /* I2C bus multiplexer */
  78 #define I2C_MUX_PCA_ADDR_PRI            0x77 /* Primary Mux*/
  79 #define I2C_MUX_CH_DEFAULT              0x8
  80
  81 /* RTC */
  82 #define RTC
  83 #define CONFIG_SYS_I2C_RTC_ADDR         0x51  /* Channel 3*/
  84
  85 /* EEPROM */
  86 #define CONFIG_SYS_I2C_EEPROM_NXID
  87 #define CONFIG_SYS_EEPROM_BUS_NUM               0
  88
  89 /* Qixis */
  90 #define CONFIG_SYS_I2C_FPGA_ADDR                0x66
  91
  92 /* USB */
  93
  94 #define COUNTER_FREQUENCY_REAL          (get_board_sys_clk() / 4)
  95
  96 #define CONFIG_HWCONFIG
  97 #define HWCONFIG_BUFFER_SIZE            128
  98
  99 #define CONFIG_SYS_BOOTM_LEN   (64 << 20)      /* Increase max gunzip size */
 100
 101 /* Initial environment variables */
 102 #define XSPI_MC_INIT_CMD                                \
 103         "sf probe 0:0 && "                              \
 104         "sf read 0x80640000 0x640000 0x80000 && "       \
 105         "sf read $fdt_addr_r 0xf00000 0x100000 && "     \
 106         "env exists secureboot && "                     \
 107         "esbc_validate 0x80640000 && "                  \
 108         "esbc_validate 0x80680000; "                    \
 109         "sf read 0x80a00000 0xa00000 0x300000 && "      \
 110         "sf read 0x80e00000 0xe00000 0x100000; "        \
 111         "fsl_mc start mc 0x80a00000 0x80e00000\0"
 112
 113 #define SD_MC_INIT_CMD                          \
 114         "mmc read 0x80a00000 0x5000 0x1200;"    \
 115         "mmc read 0x80e00000 0x7000 0x800;"     \
 116         "mmc read $fdt_addr_r 0x7800 0x800;"    \
 117         "env exists secureboot && "             \
 118         "mmc read 0x80640000 0x3200 0x20 && "   \
 119         "mmc read 0x80680000 0x3400 0x20 && "   \
 120         "esbc_validate 0x80640000 && "          \
 121         "esbc_validate 0x80680000 ;"            \
 122         "fsl_mc start mc 0x80a00000 0x80e00000\0"
 123
 124 #define SD2_MC_INIT_CMD                         \
 125         "mmc dev 1; mmc read 0x80a00000 0x5000 0x1200;" \
 126         "mmc read 0x80e00000 0x7000 0x800;"     \
 127         "mmc read $fdt_addr_r 0x7800 0x800;"    \
 128         "env exists secureboot && "             \
 129         "mmc read 0x80640000 0x3200 0x20 && "   \
 130         "mmc read 0x80680000 0x3400 0x20 && "   \
 131         "esbc_validate 0x80640000 && "          \
 132         "esbc_validate 0x80680000 ;"            \
 133         "fsl_mc start mc 0x80a00000 0x80e00000\0"
 134
 135 #define EXTRA_ENV_SETTINGS                      \
 136         "hwconfig=fsl_ddr:bank_intlv=auto\0"    \
 137         "ramdisk_addr=0x800000\0"               \
 138         "ramdisk_size=0x2000000\0"              \
 139         "fdt_high=0xa0000000\0"                 \
 140         "initrd_high=0xffffffffffffffff\0"      \
 141         "kernel_start=0x1000000\0"              \
 142         "kernelheader_start=0x600000\0"         \
 143         "scriptaddr=0x80000000\0"               \
 144         "scripthdraddr=0x80080000\0"            \
 145         "fdtheader_addr_r=0x80100000\0"         \
 146         "kernelheader_addr_r=0x80200000\0"      \
 147         "kernel_addr_r=0x81000000\0"            \
 148         "kernelheader_size=0x40000\0"           \
 149         "fdt_addr_r=0x90000000\0"               \
 150         "load_addr=0xa0000000\0"                \
 151         "kernel_size=0x2800000\0"               \
 152         "kernel_addr_sd=0x8000\0"               \
 153         "kernelhdr_addr_sd=0x3000\0"            \
 154         "kernel_size_sd=0x14000\0"              \
 155         "kernelhdr_size_sd=0x20\0"              \
 156         "console=ttyAMA0,38400n8\0"             \
 157         BOOTENV                                 \
 158         "mcmemsize=0x70000000\0"                \
 159         XSPI_MC_INIT_CMD                                \
 160         "scan_dev_for_boot_part="               \
 161                 "part list ${devtype} ${devnum} devplist; "     \
 162                 "env exists devplist || setenv devplist 1; "    \
 163                 "for distro_bootpart in ${devplist}; do "       \
 164                         "if fstype ${devtype} "                 \
 165                                 "${devnum}:${distro_bootpart} " \
 166                                 "bootfstype; then "             \
 167                                 "run scan_dev_for_boot; "       \
 168                         "fi; "                                  \
 169                 "done\0"                                        \
 170         "boot_a_script="                                        \
 171                 "load ${devtype} ${devnum}:${distro_bootpart} " \
 172                         "${scriptaddr} ${prefix}${script}; "    \
 173                 "env exists secureboot && load ${devtype} "     \
 174                         "${devnum}:${distro_bootpart} "         \
 175                         "${scripthdraddr} ${prefix}${boot_script_hdr} " \
 176                         "&& esbc_validate ${scripthdraddr};"    \
 177                 "source ${scriptaddr}\0"
 178
 179 #define XSPI_NOR_BOOTCOMMAND                                            \
 180                         "sf probe 0:0; "                                \
 181                         "sf read 0x806c0000 0x6c0000 0x40000; "         \
 182                         "env exists mcinitcmd && env exists secureboot" \
 183                         " && esbc_validate 0x806c0000; "                \
 184                         "sf read 0x80d00000 0xd00000 0x100000; "        \
 185                         "env exists mcinitcmd && "                      \
 186                         "fsl_mc lazyapply dpl 0x80d00000; "             \
 187                         "run distro_bootcmd;run xspi_bootcmd; "         \
 188                         "env exists secureboot && esbc_halt;"
 189
 190 #define SD_BOOTCOMMAND                                          \
 191                 "env exists mcinitcmd && mmcinfo; "             \
 192                 "mmc read 0x80d00000 0x6800 0x800; "            \
 193                 "env exists mcinitcmd && env exists secureboot "        \
 194                 " && mmc read 0x806C0000 0x3600 0x20 "          \
 195                 "&& esbc_validate 0x806C0000;env exists mcinitcmd "     \
 196                 "&& fsl_mc lazyapply dpl 0x80d00000;"           \
 197                 "run distro_bootcmd;run sd_bootcmd;"            \
 198                 "env exists secureboot && esbc_halt;"
 199
 200 #define SD2_BOOTCOMMAND                                         \
 201                 "mmc dev 1; env exists mcinitcmd && mmcinfo; "  \
 202                 "mmc read 0x80d00000 0x6800 0x800; "            \
 203                 "env exists mcinitcmd && env exists secureboot "        \
 204                 " && mmc read 0x806C0000 0x3600 0x20 "          \
 205                 "&& esbc_validate 0x806C0000;env exists mcinitcmd "     \
 206                 "&& fsl_mc lazyapply dpl 0x80d00000;"           \
 207                 "run distro_bootcmd;run sd2_bootcmd;"           \
 208                 "env exists secureboot && esbc_halt;"
 209
 210 #ifdef CONFIG_CMD_USB
 211 #define BOOT_TARGET_DEVICES_USB(func) func(USB, usb, 0)
 212 #else
 213 #define BOOT_TARGET_DEVICES_USB(func)
 214 #endif
 215
 216 #ifdef CONFIG_MMC
 217 #define BOOT_TARGET_DEVICES_MMC(func, instance) func(MMC, mmc, instance)
 218 #else
 219 #define BOOT_TARGET_DEVICES_MMC(func)
 220 #endif
 221
 222 #ifdef CONFIG_SCSI
 223 #define BOOT_TARGET_DEVICES_SCSI(func) func(SCSI, scsi, 0)
 224 #else
 225 #define BOOT_TARGET_DEVICES_SCSI(func)
 226 #endif
 227
 228 #ifdef CONFIG_CMD_DHCP
 229 #define BOOT_TARGET_DEVICES_DHCP(func) func(DHCP, dhcp, na)
 230 #else
 231 #define BOOT_TARGET_DEVICES_DHCP(func)
 232 #endif
 233
 234 #define BOOT_TARGET_DEVICES(func) \
 235         BOOT_TARGET_DEVICES_USB(func) \
 236         BOOT_TARGET_DEVICES_MMC(func, 0) \
 237         BOOT_TARGET_DEVICES_MMC(func, 1) \
 238         BOOT_TARGET_DEVICES_SCSI(func) \
 239         BOOT_TARGET_DEVICES_DHCP(func)
 240 #include <config_distro_bootcmd.h>
 241
 242 #endif /* __LX2_COMMON_H */