include/configs/lx2160a_common.h

   1 /* SPDX-License-Identifier: GPL-2.0+ */
   2 /*
   3  * Copyright 2018-2021 NXP
   4  */
   5
   6 #ifndef __LX2_COMMON_H
   7 #define __LX2_COMMON_H
   8
   9 #include <asm/arch/stream_id_lsch3.h>
  10 #include <asm/arch/config.h>
  11 #include <asm/arch/soc.h>
  12
  13 #define CFG_SYS_FLASH_BASE              0x20000000
  14
  15 /* DDR */
  16 #define CFG_SYS_DDR_SDRAM_BASE          0x80000000UL
  17 #define CFG_SYS_FSL_DDR_SDRAM_BASE_PHY  0
  18 #define CFG_SYS_DDR_BLOCK2_BASE         0x2080000000ULL
  19 #define CFG_SYS_SDRAM_SIZE                      0x200000000UL
  20 #define CFG_SYS_SDRAM_BASE              CFG_SYS_DDR_SDRAM_BASE
  21 #define SPD_EEPROM_ADDRESS1             0x51
  22 #define SPD_EEPROM_ADDRESS2             0x52
  23 #define SPD_EEPROM_ADDRESS3             0x53
  24 #define SPD_EEPROM_ADDRESS4             0x54
  25 #define SPD_EEPROM_ADDRESS5             0x55
  26 #define SPD_EEPROM_ADDRESS6             0x56
  27 #define SPD_EEPROM_ADDRESS              SPD_EEPROM_ADDRESS1
  28
  29 /* Miscellaneous configurable options */
  30
  31 /* SMP Definitinos  */
  32 #define CPU_RELEASE_ADDR                secondary_boot_addr
  33
  34 /* Generic Timer Definitions */
  35 /*
  36  * This is not an accurate number. It is used in start.S. The frequency
  37  * will be udpated later when get_bus_freq(0) is available.
  38  */
  39
  40
  41 /* Serial Port */
  42 #define CFG_PL011_CLOCK         (get_bus_freq(0) / 4)
  43 #define CFG_SYS_SERIAL0         0x21c0000
  44 #define CFG_SYS_SERIAL1         0x21d0000
  45 #define CFG_SYS_SERIAL2         0x21e0000
  46 #define CFG_SYS_SERIAL3         0x21f0000
  47 /*below might needs to be removed*/
  48 #define CFG_PL01x_PORTS         {(void *)CFG_SYS_SERIAL0, \
  49                                         (void *)CFG_SYS_SERIAL1, \
  50                                         (void *)CFG_SYS_SERIAL2, \
  51                                         (void *)CFG_SYS_SERIAL3 }
  52
  53 /* MC firmware */
  54 #define CFG_SYS_LS_MC_DPC_MAX_LENGTH            0x20000
  55 #define CFG_SYS_LS_MC_DRAM_DPC_OFFSET   0x00F00000
  56 #define CFG_SYS_LS_MC_DPL_MAX_LENGTH            0x20000
  57 #define CFG_SYS_LS_MC_DRAM_DPL_OFFSET   0x00F20000
  58 #define CFG_SYS_LS_MC_BOOT_TIMEOUT_MS   5000
  59
  60 /*
  61  * Carve out a DDR region which will not be used by u-boot/Linux
  62  *
  63  * It will be used by MC and Debug Server. The MC region must be
  64  * 512MB aligned, so the min size to hide is 512MB.
  65  */
  66 #ifdef CONFIG_FSL_MC_ENET
  67 #define CFG_SYS_LS_MC_DRAM_BLOCK_MIN_SIZE       (256UL * 1024 * 1024)
  68 #endif
  69
  70 /* I2C bus multiplexer */
  71 #define I2C_MUX_PCA_ADDR_PRI            0x77 /* Primary Mux*/
  72 #define I2C_MUX_CH_DEFAULT              0x8
  73
  74 /* RTC */
  75 #define CFG_SYS_I2C_RTC_ADDR            0x51  /* Channel 3*/
  76
  77 /* Qixis */
  78 #define CFG_SYS_I2C_FPGA_ADDR           0x66
  79
  80 /* USB */
  81
  82 #define COUNTER_FREQUENCY_REAL          (get_board_sys_clk() / 4)
  83
  84 #define HWCONFIG_BUFFER_SIZE            128
  85
  86 /* Initial environment variables */
  87 #define XSPI_MC_INIT_CMD                                \
  88         "sf probe 0:0 && "                              \
  89         "sf read 0x80640000 0x640000 0x80000 && "       \
  90         "sf read $fdt_addr_r 0xf00000 0x100000 && "     \
  91         "env exists secureboot && "                     \
  92         "esbc_validate 0x80640000 && "                  \
  93         "esbc_validate 0x80680000; "                    \
  94         "sf read 0x80a00000 0xa00000 0x300000 && "      \
  95         "sf read 0x80e00000 0xe00000 0x100000; "        \
  96         "fsl_mc start mc 0x80a00000 0x80e00000\0"
  97
  98 #define SD_MC_INIT_CMD                          \
  99         "mmc read 0x80a00000 0x5000 0x1200;"    \
 100         "mmc read 0x80e00000 0x7000 0x800;"     \
 101         "mmc read $fdt_addr_r 0x7800 0x800;"    \
 102         "env exists secureboot && "             \
 103         "mmc read 0x80640000 0x3200 0x20 && "   \
 104         "mmc read 0x80680000 0x3400 0x20 && "   \
 105         "esbc_validate 0x80640000 && "          \
 106         "esbc_validate 0x80680000 ;"            \
 107         "fsl_mc start mc 0x80a00000 0x80e00000\0"
 108
 109 #define SD2_MC_INIT_CMD                         \
 110         "mmc dev 1; mmc read 0x80a00000 0x5000 0x1200;" \
 111         "mmc read 0x80e00000 0x7000 0x800;"     \
 112         "mmc read $fdt_addr_r 0x7800 0x800;"    \
 113         "env exists secureboot && "             \
 114         "mmc read 0x80640000 0x3200 0x20 && "   \
 115         "mmc read 0x80680000 0x3400 0x20 && "   \
 116         "esbc_validate 0x80640000 && "          \
 117         "esbc_validate 0x80680000 ;"            \
 118         "fsl_mc start mc 0x80a00000 0x80e00000\0"
 119
 120 #define EXTRA_ENV_SETTINGS                      \
 121         "hwconfig=fsl_ddr:bank_intlv=auto\0"    \
 122         "ramdisk_addr=0x800000\0"               \
 123         "ramdisk_size=0x2000000\0"              \
 124         "fdt_high=0xa0000000\0"                 \
 125         "initrd_high=0xffffffffffffffff\0"      \
 126         "kernel_start=0x1000000\0"              \
 127         "kernelheader_start=0x600000\0"         \
 128         "scriptaddr=0x80000000\0"               \
 129         "scripthdraddr=0x80080000\0"            \
 130         "fdtheader_addr_r=0x80100000\0"         \
 131         "kernelheader_addr_r=0x80200000\0"      \
 132         "kernel_addr_r=0x81000000\0"            \
 133         "kernelheader_size=0x40000\0"           \
 134         "fdt_addr_r=0x90000000\0"               \
 135         "load_addr=0xa0000000\0"                \
 136         "kernel_size=0x2800000\0"               \
 137         "kernel_addr_sd=0x8000\0"               \
 138         "kernelhdr_addr_sd=0x3000\0"            \
 139         "kernel_size_sd=0x14000\0"              \
 140         "kernelhdr_size_sd=0x20\0"              \
 141         "console=ttyAMA0,38400n8\0"             \
 142         BOOTENV                                 \
 143         "mcmemsize=0x70000000\0"                \
 144         XSPI_MC_INIT_CMD                                \
 145         "scan_dev_for_boot_part="               \
 146                 "part list ${devtype} ${devnum} devplist; "     \
 147                 "env exists devplist || setenv devplist 1; "    \
 148                 "for distro_bootpart in ${devplist}; do "       \
 149                         "if fstype ${devtype} "                 \
 150                                 "${devnum}:${distro_bootpart} " \
 151                                 "bootfstype; then "             \
 152                                 "run scan_dev_for_boot; "       \
 153                         "fi; "                                  \
 154                 "done\0"                                        \
 155         "boot_a_script="                                        \
 156                 "load ${devtype} ${devnum}:${distro_bootpart} " \
 157                         "${scriptaddr} ${prefix}${script}; "    \
 158                 "env exists secureboot && load ${devtype} "     \
 159                         "${devnum}:${distro_bootpart} "         \
 160                         "${scripthdraddr} ${prefix}${boot_script_hdr} " \
 161                         "&& esbc_validate ${scripthdraddr};"    \
 162                 "source ${scriptaddr}\0"
 163
 164 #define XSPI_NOR_BOOTCOMMAND                                            \
 165                         "sf probe 0:0; "                                \
 166                         "sf read 0x806c0000 0x6c0000 0x40000; "         \
 167                         "env exists mcinitcmd && env exists secureboot" \
 168                         " && esbc_validate 0x806c0000; "                \
 169                         "sf read 0x80d00000 0xd00000 0x100000; "        \
 170                         "env exists mcinitcmd && "                      \
 171                         "fsl_mc lazyapply dpl 0x80d00000; "             \
 172                         "run distro_bootcmd;run xspi_bootcmd; "         \
 173                         "env exists secureboot && esbc_halt;"
 174
 175 #define SD_BOOTCOMMAND                                          \
 176                 "env exists mcinitcmd && mmcinfo; "             \
 177                 "mmc read 0x80d00000 0x6800 0x800; "            \
 178                 "env exists mcinitcmd && env exists secureboot "        \
 179                 " && mmc read 0x806C0000 0x3600 0x20 "          \
 180                 "&& esbc_validate 0x806C0000;env exists mcinitcmd "     \
 181                 "&& fsl_mc lazyapply dpl 0x80d00000;"           \
 182                 "run distro_bootcmd;run sd_bootcmd;"            \
 183                 "env exists secureboot && esbc_halt;"
 184
 185 #define SD2_BOOTCOMMAND                                         \
 186                 "mmc dev 1; env exists mcinitcmd && mmcinfo; "  \
 187                 "mmc read 0x80d00000 0x6800 0x800; "            \
 188                 "env exists mcinitcmd && env exists secureboot "        \
 189                 " && mmc read 0x806C0000 0x3600 0x20 "          \
 190                 "&& esbc_validate 0x806C0000;env exists mcinitcmd "     \
 191                 "&& fsl_mc lazyapply dpl 0x80d00000;"           \
 192                 "run distro_bootcmd;run sd2_bootcmd;"           \
 193                 "env exists secureboot && esbc_halt;"
 194
 195 #ifdef CONFIG_CMD_USB
 196 #define BOOT_TARGET_DEVICES_USB(func) func(USB, usb, 0)
 197 #else
 198 #define BOOT_TARGET_DEVICES_USB(func)
 199 #endif
 200
 201 #ifdef CONFIG_MMC
 202 #define BOOT_TARGET_DEVICES_MMC(func, instance) func(MMC, mmc, instance)
 203 #else
 204 #define BOOT_TARGET_DEVICES_MMC(func)
 205 #endif
 206
 207 #ifdef CONFIG_SCSI
 208 #define BOOT_TARGET_DEVICES_SCSI(func) func(SCSI, scsi, 0)
 209 #else
 210 #define BOOT_TARGET_DEVICES_SCSI(func)
 211 #endif
 212
 213 #ifdef CONFIG_CMD_DHCP
 214 #define BOOT_TARGET_DEVICES_DHCP(func) func(DHCP, dhcp, na)
 215 #else
 216 #define BOOT_TARGET_DEVICES_DHCP(func)
 217 #endif
 218
 219 #define BOOT_TARGET_DEVICES(func) \
 220         BOOT_TARGET_DEVICES_USB(func) \
 221         BOOT_TARGET_DEVICES_MMC(func, 0) \
 222         BOOT_TARGET_DEVICES_MMC(func, 1) \
 223         BOOT_TARGET_DEVICES_SCSI(func) \
 224         BOOT_TARGET_DEVICES_DHCP(func)
 225 #include <config_distro_bootcmd.h>
 226
 227 #endif /* __LX2_COMMON_H */