include/configs/ls2080ardb.h

   1 /*
   2  * Copyright 2015 Freescale Semiconductor
   3  *
   4  * SPDX-License-Identifier:     GPL-2.0+
   5  */
   6
   7 #ifndef __LS2_RDB_H
   8 #define __LS2_RDB_H
   9
  10 #include "ls2080a_common.h"
  11
  12 #undef CONFIG_CONS_INDEX
  13 #define CONFIG_CONS_INDEX       2
  14
  15 #define I2C_MUX_CH_VOL_MONITOR          0xa
  16 #define I2C_VOL_MONITOR_ADDR            0x38
  17 #define CONFIG_VOL_MONITOR_IR36021_READ
  18 #define CONFIG_VOL_MONITOR_IR36021_SET
  19
  20 #define CONFIG_VID_FLS_ENV              "ls2080ardb_vdd_mv"
  21 #ifndef CONFIG_SPL_BUILD
  22 #define CONFIG_VID
  23 #endif
  24 /* step the IR regulator in 5mV increments */
  25 #define IR_VDD_STEP_DOWN                5
  26 #define IR_VDD_STEP_UP                  5
  27 /* The lowest and highest voltage allowed for LS2080ARDB */
  28 #define VDD_MV_MIN                      819
  29 #define VDD_MV_MAX                      1212
  30
  31 #ifndef __ASSEMBLY__
  32 unsigned long get_board_sys_clk(void);
  33 #endif
  34
  35 #define CONFIG_SYS_FSL_CLK
  36 #define CONFIG_SYS_CLK_FREQ             get_board_sys_clk()
  37 #define CONFIG_DDR_CLK_FREQ             133333333
  38 #define COUNTER_FREQUENCY_REAL          (CONFIG_SYS_CLK_FREQ/4)
  39
  40 #define CONFIG_DDR_SPD
  41 #define CONFIG_DDR_ECC
  42 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
  43 #define CONFIG_MEM_INIT_VALUE           0xdeadbeef
  44 #define SPD_EEPROM_ADDRESS1     0x51
  45 #define SPD_EEPROM_ADDRESS2     0x52
  46 #define SPD_EEPROM_ADDRESS3     0x53
  47 #define SPD_EEPROM_ADDRESS4     0x54
  48 #define SPD_EEPROM_ADDRESS5     0x55
  49 #define SPD_EEPROM_ADDRESS6     0x56    /* dummy address */
  50 #define SPD_EEPROM_ADDRESS      SPD_EEPROM_ADDRESS1
  51 #define CONFIG_SYS_SPD_BUS_NUM  0       /* SPD on I2C bus 0 */
  52 #define CONFIG_DIMM_SLOTS_PER_CTLR              2
  53 #define CONFIG_CHIP_SELECTS_PER_CTRL            4
  54 #ifdef CONFIG_SYS_FSL_HAS_DP_DDR
  55 #define CONFIG_DP_DDR_DIMM_SLOTS_PER_CTLR       1
  56 #endif
  57 #define CONFIG_FSL_DDR_BIST     /* enable built-in memory test */
  58
  59 /* SATA */
  60 #define CONFIG_LIBATA
  61 #define CONFIG_SCSI_AHCI
  62 #define CONFIG_SCSI_AHCI_PLAT
  63 #define CONFIG_SCSI
  64 #define CONFIG_DOS_PARTITION
  65 #define CONFIG_BOARD_LATE_INIT
  66
  67 #define CONFIG_SYS_SATA1                        AHCI_BASE_ADDR1
  68 #define CONFIG_SYS_SATA2                        AHCI_BASE_ADDR2
  69
  70 #define CONFIG_SYS_SCSI_MAX_SCSI_ID             1
  71 #define CONFIG_SYS_SCSI_MAX_LUN                 1
  72 #define CONFIG_SYS_SCSI_MAX_DEVICE              (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
  73                                                 CONFIG_SYS_SCSI_MAX_LUN)
  74
  75 /* undefined CONFIG_FSL_DDR_SYNC_REFRESH for simulator */
  76
  77 #define CONFIG_SYS_NOR0_CSPR_EXT        (0x0)
  78 #define CONFIG_SYS_NOR_AMASK            IFC_AMASK(128*1024*1024)
  79 #define CONFIG_SYS_NOR_AMASK_EARLY      IFC_AMASK(64*1024*1024)
  80
  81 #define CONFIG_SYS_NOR0_CSPR                                    \
  82         (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS)             | \
  83         CSPR_PORT_SIZE_16                                       | \
  84         CSPR_MSEL_NOR                                           | \
  85         CSPR_V)
  86 #define CONFIG_SYS_NOR0_CSPR_EARLY                              \
  87         (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS_EARLY)       | \
  88         CSPR_PORT_SIZE_16                                       | \
  89         CSPR_MSEL_NOR                                           | \
  90         CSPR_V)
  91 #define CONFIG_SYS_NOR_CSOR     CSOR_NOR_ADM_SHIFT(12)
  92 #define CONFIG_SYS_NOR_FTIM0    (FTIM0_NOR_TACSE(0x4) | \
  93                                 FTIM0_NOR_TEADC(0x5) | \
  94                                 FTIM0_NOR_TEAHC(0x5))
  95 #define CONFIG_SYS_NOR_FTIM1    (FTIM1_NOR_TACO(0x35) | \
  96                                 FTIM1_NOR_TRAD_NOR(0x1a) |\
  97                                 FTIM1_NOR_TSEQRAD_NOR(0x13))
  98 #define CONFIG_SYS_NOR_FTIM2    (FTIM2_NOR_TCS(0x4) | \
  99                                 FTIM2_NOR_TCH(0x4) | \
 100                                 FTIM2_NOR_TWPH(0x0E) | \
 101                                 FTIM2_NOR_TWP(0x1c))
 102 #define CONFIG_SYS_NOR_FTIM3    0x04000000
 103 #define CONFIG_SYS_IFC_CCR      0x01000000
 104
 105 #ifndef CONFIG_SYS_NO_FLASH
 106 #define CONFIG_FLASH_CFI_DRIVER
 107 #define CONFIG_SYS_FLASH_CFI
 108 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
 109 #define CONFIG_SYS_FLASH_QUIET_TEST
 110 #define CONFIG_FLASH_SHOW_PROGRESS      45 /* count down from 45/5: 9..1 */
 111
 112 #define CONFIG_SYS_MAX_FLASH_BANKS      1       /* number of banks */
 113 #define CONFIG_SYS_MAX_FLASH_SECT       1024    /* sectors per device */
 114 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000   /* Flash Erase Timeout (ms) */
 115 #define CONFIG_SYS_FLASH_WRITE_TOUT     500     /* Flash Write Timeout (ms) */
 116
 117 #define CONFIG_SYS_FLASH_EMPTY_INFO
 118 #define CONFIG_SYS_FLASH_BANKS_LIST     { CONFIG_SYS_FLASH_BASE,\
 119                                          CONFIG_SYS_FLASH_BASE + 0x40000000}
 120 #endif
 121
 122 #define CONFIG_NAND_FSL_IFC
 123 #define CONFIG_SYS_NAND_MAX_ECCPOS      256
 124 #define CONFIG_SYS_NAND_MAX_OOBFREE     2
 125
 126 #define CONFIG_SYS_NAND_CSPR_EXT        (0x0)
 127 #define CONFIG_SYS_NAND_CSPR    (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
 128                                 | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
 129                                 | CSPR_MSEL_NAND        /* MSEL = NAND */ \
 130                                 | CSPR_V)
 131 #define CONFIG_SYS_NAND_AMASK   IFC_AMASK(64 * 1024)
 132
 133 #define CONFIG_SYS_NAND_CSOR    (CSOR_NAND_ECC_ENC_EN   /* ECC on encode */ \
 134                                 | CSOR_NAND_ECC_DEC_EN  /* ECC on decode */ \
 135                                 | CSOR_NAND_ECC_MODE_4  /* 4-bit ECC */ \
 136                                 | CSOR_NAND_RAL_3       /* RAL = 3Byes */ \
 137                                 | CSOR_NAND_PGS_4K      /* Page Size = 4K */ \
 138                                 | CSOR_NAND_SPRZ_224    /* Spare size = 224 */ \
 139                                 | CSOR_NAND_PB(128))    /* Pages Per Block 128*/
 140
 141 #define CONFIG_SYS_NAND_ONFI_DETECTION
 142
 143 /* ONFI NAND Flash mode0 Timing Params */
 144 #define CONFIG_SYS_NAND_FTIM0           (FTIM0_NAND_TCCST(0x0e) | \
 145                                         FTIM0_NAND_TWP(0x30)   | \
 146                                         FTIM0_NAND_TWCHT(0x0e) | \
 147                                         FTIM0_NAND_TWH(0x14))
 148 #define CONFIG_SYS_NAND_FTIM1           (FTIM1_NAND_TADLE(0x64) | \
 149                                         FTIM1_NAND_TWBE(0xab)  | \
 150                                         FTIM1_NAND_TRR(0x1c)   | \
 151                                         FTIM1_NAND_TRP(0x30))
 152 #define CONFIG_SYS_NAND_FTIM2           (FTIM2_NAND_TRAD(0x1e) | \
 153                                         FTIM2_NAND_TREH(0x14) | \
 154                                         FTIM2_NAND_TWHRE(0x3c))
 155 #define CONFIG_SYS_NAND_FTIM3           0x0
 156
 157 #define CONFIG_SYS_NAND_BASE_LIST       { CONFIG_SYS_NAND_BASE }
 158 #define CONFIG_SYS_MAX_NAND_DEVICE      1
 159 #define CONFIG_MTD_NAND_VERIFY_WRITE
 160 #define CONFIG_CMD_NAND
 161
 162 #define CONFIG_SYS_NAND_BLOCK_SIZE      (512 * 1024)
 163
 164 #define CONFIG_FSL_QIXIS        /* use common QIXIS code */
 165 #define QIXIS_LBMAP_SWITCH              0x06
 166 #define QIXIS_LBMAP_MASK                0x0f
 167 #define QIXIS_LBMAP_SHIFT               0
 168 #define QIXIS_LBMAP_DFLTBANK            0x00
 169 #define QIXIS_LBMAP_ALTBANK             0x04
 170 #define QIXIS_LBMAP_NAND                0x09
 171 #define QIXIS_RST_CTL_RESET             0x31
 172 #define QIXIS_RST_CTL_RESET_EN          0x30
 173 #define QIXIS_RCFG_CTL_RECONFIG_IDLE    0x20
 174 #define QIXIS_RCFG_CTL_RECONFIG_START   0x21
 175 #define QIXIS_RCFG_CTL_WATCHDOG_ENBLE   0x08
 176 #define QIXIS_RCW_SRC_NAND              0x119
 177 #define QIXIS_RST_FORCE_MEM             0x01
 178
 179 #define CONFIG_SYS_CSPR3_EXT    (0x0)
 180 #define CONFIG_SYS_CSPR3        (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS_EARLY) \
 181                                 | CSPR_PORT_SIZE_8 \
 182                                 | CSPR_MSEL_GPCM \
 183                                 | CSPR_V)
 184 #define CONFIG_SYS_CSPR3_FINAL  (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \
 185                                 | CSPR_PORT_SIZE_8 \
 186                                 | CSPR_MSEL_GPCM \
 187                                 | CSPR_V)
 188
 189 #define CONFIG_SYS_AMASK3       IFC_AMASK(64*1024)
 190 #define CONFIG_SYS_CSOR3        CSOR_GPCM_ADM_SHIFT(12)
 191 /* QIXIS Timing parameters for IFC CS3 */
 192 #define CONFIG_SYS_CS3_FTIM0            (FTIM0_GPCM_TACSE(0x0e) | \
 193                                         FTIM0_GPCM_TEADC(0x0e) | \
 194                                         FTIM0_GPCM_TEAHC(0x0e))
 195 #define CONFIG_SYS_CS3_FTIM1            (FTIM1_GPCM_TACO(0xff) | \
 196                                         FTIM1_GPCM_TRAD(0x3f))
 197 #define CONFIG_SYS_CS3_FTIM2            (FTIM2_GPCM_TCS(0xf) | \
 198                                         FTIM2_GPCM_TCH(0xf) | \
 199                                         FTIM2_GPCM_TWP(0x3E))
 200 #define CONFIG_SYS_CS3_FTIM3            0x0
 201
 202 #if defined(CONFIG_SPL) && defined(CONFIG_NAND)
 203 #define CONFIG_SYS_CSPR2_EXT            CONFIG_SYS_NOR0_CSPR_EXT
 204 #define CONFIG_SYS_CSPR2                CONFIG_SYS_NOR0_CSPR_EARLY
 205 #define CONFIG_SYS_CSPR2_FINAL          CONFIG_SYS_NOR0_CSPR
 206 #define CONFIG_SYS_AMASK2               CONFIG_SYS_NOR_AMASK
 207 #define CONFIG_SYS_CSOR2                CONFIG_SYS_NOR_CSOR
 208 #define CONFIG_SYS_CS2_FTIM0            CONFIG_SYS_NOR_FTIM0
 209 #define CONFIG_SYS_CS2_FTIM1            CONFIG_SYS_NOR_FTIM1
 210 #define CONFIG_SYS_CS2_FTIM2            CONFIG_SYS_NOR_FTIM2
 211 #define CONFIG_SYS_CS2_FTIM3            CONFIG_SYS_NOR_FTIM3
 212 #define CONFIG_SYS_CSPR0_EXT            CONFIG_SYS_NAND_CSPR_EXT
 213 #define CONFIG_SYS_CSPR0                CONFIG_SYS_NAND_CSPR
 214 #define CONFIG_SYS_AMASK0               CONFIG_SYS_NAND_AMASK
 215 #define CONFIG_SYS_CSOR0                CONFIG_SYS_NAND_CSOR
 216 #define CONFIG_SYS_CS0_FTIM0            CONFIG_SYS_NAND_FTIM0
 217 #define CONFIG_SYS_CS0_FTIM1            CONFIG_SYS_NAND_FTIM1
 218 #define CONFIG_SYS_CS0_FTIM2            CONFIG_SYS_NAND_FTIM2
 219 #define CONFIG_SYS_CS0_FTIM3            CONFIG_SYS_NAND_FTIM3
 220
 221 #define CONFIG_ENV_IS_IN_NAND
 222 #define CONFIG_ENV_OFFSET               (2048 * 1024)
 223 #define CONFIG_ENV_SECT_SIZE            0x20000
 224 #define CONFIG_ENV_SIZE                 0x2000
 225 #define CONFIG_SPL_PAD_TO               0x80000
 226 #define CONFIG_SYS_NAND_U_BOOT_OFFS     (1024 * 1024)
 227 #define CONFIG_SYS_NAND_U_BOOT_SIZE     (512 * 1024)
 228 #else
 229 #define CONFIG_SYS_CSPR0_EXT            CONFIG_SYS_NOR0_CSPR_EXT
 230 #define CONFIG_SYS_CSPR0                CONFIG_SYS_NOR0_CSPR_EARLY
 231 #define CONFIG_SYS_CSPR0_FINAL          CONFIG_SYS_NOR0_CSPR
 232 #define CONFIG_SYS_AMASK0               CONFIG_SYS_NOR_AMASK
 233 #define CONFIG_SYS_CSOR0                CONFIG_SYS_NOR_CSOR
 234 #define CONFIG_SYS_CS0_FTIM0            CONFIG_SYS_NOR_FTIM0
 235 #define CONFIG_SYS_CS0_FTIM1            CONFIG_SYS_NOR_FTIM1
 236 #define CONFIG_SYS_CS0_FTIM2            CONFIG_SYS_NOR_FTIM2
 237 #define CONFIG_SYS_CS0_FTIM3            CONFIG_SYS_NOR_FTIM3
 238 #define CONFIG_SYS_CSPR2_EXT            CONFIG_SYS_NAND_CSPR_EXT
 239 #define CONFIG_SYS_CSPR2                CONFIG_SYS_NAND_CSPR
 240 #define CONFIG_SYS_AMASK2               CONFIG_SYS_NAND_AMASK
 241 #define CONFIG_SYS_CSOR2                CONFIG_SYS_NAND_CSOR
 242 #define CONFIG_SYS_CS2_FTIM0            CONFIG_SYS_NAND_FTIM0
 243 #define CONFIG_SYS_CS2_FTIM1            CONFIG_SYS_NAND_FTIM1
 244 #define CONFIG_SYS_CS2_FTIM2            CONFIG_SYS_NAND_FTIM2
 245 #define CONFIG_SYS_CS2_FTIM3            CONFIG_SYS_NAND_FTIM3
 246
 247 #define CONFIG_ENV_IS_IN_FLASH
 248 #define CONFIG_ENV_ADDR                 (CONFIG_SYS_FLASH_BASE + 0x200000)
 249 #define CONFIG_ENV_SECT_SIZE            0x20000
 250 #define CONFIG_ENV_SIZE                 0x2000
 251 #endif
 252
 253 /* Debug Server firmware */
 254 #define CONFIG_SYS_DEBUG_SERVER_FW_IN_NOR
 255 #define CONFIG_SYS_DEBUG_SERVER_FW_ADDR 0x580D00000ULL
 256
 257 #define CONFIG_SYS_LS_MC_BOOT_TIMEOUT_MS 5000
 258
 259 /*
 260  * I2C
 261  */
 262 #define I2C_MUX_PCA_ADDR                0x75
 263 #define I2C_MUX_PCA_ADDR_PRI            0x75 /* Primary Mux*/
 264
 265 /* I2C bus multiplexer */
 266 #define I2C_MUX_CH_DEFAULT      0x8
 267
 268 /* SPI */
 269 #ifdef CONFIG_FSL_DSPI
 270 #define CONFIG_SPI_FLASH
 271 #define CONFIG_SPI_FLASH_BAR
 272 #define CONFIG_SPI_FLASH_STMICRO
 273 #endif
 274
 275 /*
 276  * RTC configuration
 277  */
 278 #define RTC
 279 #define CONFIG_RTC_DS3231               1
 280 #define CONFIG_SYS_I2C_RTC_ADDR         0x68
 281 #define CONFIG_CMD_DATE
 282
 283 /* EEPROM */
 284 #define CONFIG_ID_EEPROM
 285 #define CONFIG_CMD_EEPROM
 286 #define CONFIG_SYS_I2C_EEPROM_NXID
 287 #define CONFIG_SYS_EEPROM_BUS_NUM       0
 288 #define CONFIG_SYS_I2C_EEPROM_ADDR      0x57
 289 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN  1
 290 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
 291 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
 292
 293 #define CONFIG_FSL_MEMAC
 294
 295 #ifdef CONFIG_PCI
 296 #define CONFIG_PCI_SCAN_SHOW
 297 #define CONFIG_CMD_PCI
 298 #endif
 299
 300 /*  MMC  */
 301 #ifdef CONFIG_MMC
 302 #define CONFIG_FSL_ESDHC
 303 #define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
 304 #define CONFIG_GENERIC_MMC
 305 #define CONFIG_DOS_PARTITION
 306 #endif
 307
 308 #define CONFIG_MISC_INIT_R
 309
 310 /*
 311  * USB
 312  */
 313 #define CONFIG_HAS_FSL_XHCI_USB
 314 #define CONFIG_USB_XHCI_FSL
 315 #define CONFIG_USB_MAX_CONTROLLER_COUNT         2
 316 #define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS      2
 317
 318 #undef CONFIG_CMDLINE_EDITING
 319 #include <config_distro_defaults.h>
 320
 321 #define BOOT_TARGET_DEVICES(func) \
 322         func(USB, usb, 0) \
 323         func(MMC, mmc, 0) \
 324         func(SCSI, scsi, 0) \
 325         func(DHCP, dhcp, na)
 326 #include <config_distro_bootcmd.h>
 327
 328 /* Initial environment variables */
 329 #undef CONFIG_EXTRA_ENV_SETTINGS
 330 #define CONFIG_EXTRA_ENV_SETTINGS               \
 331         "hwconfig=fsl_ddr:bank_intlv=auto\0"    \
 332         "scriptaddr=0x80800000\0"               \
 333         "kernel_addr_r=0x81000000\0"            \
 334         "pxefile_addr_r=0x81000000\0"           \
 335         "fdt_addr_r=0x88000000\0"               \
 336         "ramdisk_addr_r=0x89000000\0"           \
 337         "loadaddr=0x80100000\0"                 \
 338         "kernel_addr=0x100000\0"                \
 339         "ramdisk_addr=0x800000\0"               \
 340         "ramdisk_size=0x2000000\0"              \
 341         "fdt_high=0xa0000000\0"                 \
 342         "initrd_high=0xffffffffffffffff\0"      \
 343         "kernel_start=0x581100000\0"            \
 344         "kernel_load=0xa0000000\0"              \
 345         "kernel_size=0x2800000\0"               \
 346         "fdtfile=fsl-ls2080a-rdb.dtb\0"         \
 347         "mcinitcmd=fsl_mc start mc 0x580300000" \
 348         " 0x580800000 \0"                       \
 349         BOOTENV
 350
 351 #undef CONFIG_BOOTARGS
 352 #define CONFIG_BOOTARGS         "console=ttyS1,115200 root=/dev/ram0 " \
 353                                 "earlycon=uart8250,mmio,0x21c0600 " \
 354                                 "ramdisk_size=0x2000000 default_hugepagesz=2m" \
 355                                 " hugepagesz=2m hugepages=256"
 356
 357 #undef CONFIG_BOOTCOMMAND
 358 /* Try to boot an on-NOR kernel first, then do normal distro boot */
 359 #define CONFIG_BOOTCOMMAND "run mcinitcmd && fsl_mc lazyapply dpl 0x580700000" \
 360                            " && cp.b $kernel_start $kernel_load $kernel_size" \
 361                            " && bootm $kernel_load" \
 362                            " || run distro_bootcmd"
 363
 364 /* MAC/PHY configuration */
 365 #ifdef CONFIG_FSL_MC_ENET
 366 #define CONFIG_PHYLIB_10G
 367 #define CONFIG_PHY_AQUANTIA
 368 #define CONFIG_PHY_CORTINA
 369 #define CONFIG_PHYLIB
 370 #define CONFIG_SYS_CORTINA_FW_IN_NOR
 371 #define CONFIG_CORTINA_FW_ADDR          0x581000000
 372 #define CONFIG_CORTINA_FW_LENGTH        0x40000
 373
 374 #define CORTINA_PHY_ADDR1       0x10
 375 #define CORTINA_PHY_ADDR2       0x11
 376 #define CORTINA_PHY_ADDR3       0x12
 377 #define CORTINA_PHY_ADDR4       0x13
 378 #define AQ_PHY_ADDR1            0x00
 379 #define AQ_PHY_ADDR2            0x01
 380 #define AQ_PHY_ADDR3            0x02
 381 #define AQ_PHY_ADDR4            0x03
 382 #define AQR405_IRQ_MASK         0x36
 383
 384 #define CONFIG_MII
 385 #define CONFIG_ETHPRIME         "DPMAC1@xgmii"
 386 #define CONFIG_PHY_GIGE
 387 #define CONFIG_PHY_AQUANTIA
 388 #endif
 389
 390 #include <asm/fsl_secure_boot.h>
 391
 392 #endif /* __LS2_RDB_H */