include/configs/ls1088ardb.h

   1 /* SPDX-License-Identifier: GPL-2.0+ */
   2 /*
   3  * Copyright 2017 NXP
   4  */
   5
   6 #ifndef __LS1088A_RDB_H
   7 #define __LS1088A_RDB_H
   8
   9 #include "ls1088a_common.h"
  10
  11 #ifdef CONFIG_TFABOOT
  12 #define CONFIG_SYS_MMC_ENV_DEV          0
  13
  14 #define CONFIG_ENV_SIZE                 0x2000          /* 8KB */
  15 #define CONFIG_ENV_OFFSET               0x500000
  16 #define CONFIG_ENV_ADDR                 (CONFIG_SYS_FLASH_BASE + \
  17                                          CONFIG_ENV_OFFSET)
  18 #define CONFIG_ENV_SECT_SIZE            0x40000
  19 #else
  20 #if defined(CONFIG_QSPI_BOOT)
  21 #define CONFIG_ENV_SIZE                 0x2000          /* 8KB */
  22 #define CONFIG_ENV_SECT_SIZE            0x40000
  23 #elif defined(CONFIG_SD_BOOT)
  24 #define CONFIG_ENV_OFFSET               (3 * 1024 * 1024)
  25 #define CONFIG_SYS_MMC_ENV_DEV          0
  26 #define CONFIG_ENV_SIZE                 0x2000
  27 #else
  28 #define CONFIG_ENV_IS_IN_FLASH
  29 #define CONFIG_ENV_ADDR                 (CONFIG_SYS_FLASH_BASE + 0x300000)
  30 #define CONFIG_ENV_SECT_SIZE            0x20000
  31 #define CONFIG_ENV_SIZE                 0x20000
  32 #endif
  33 #endif /* CONFIG_TFABOOT */
  34
  35 #if defined(CONFIG_TFABOOT) || \
  36         defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
  37 #ifndef CONFIG_SPL_BUILD
  38 #define CONFIG_QIXIS_I2C_ACCESS
  39 #endif
  40 #define SYS_NO_FLASH
  41 #undef CONFIG_CMD_IMLS
  42 #endif
  43
  44 #define CONFIG_SYS_CLK_FREQ             100000000
  45 #define CONFIG_DDR_CLK_FREQ             100000000
  46 #define COUNTER_FREQUENCY_REAL          25000000        /* 25MHz */
  47 #define COUNTER_FREQUENCY               25000000        /* 25MHz */
  48
  49 #define CONFIG_DDR_SPD
  50 #ifdef CONFIG_EMU
  51 #define CONFIG_SYS_FSL_DDR_EMU
  52 #define CONFIG_SYS_MXC_I2C1_SPEED       40000000
  53 #define CONFIG_SYS_MXC_I2C2_SPEED       40000000
  54 #else
  55 #define CONFIG_DDR_ECC
  56 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
  57 #define CONFIG_MEM_INIT_VALUE           0xdeadbeef
  58 #endif
  59 #define SPD_EEPROM_ADDRESS      0x51
  60 #define CONFIG_SYS_SPD_BUS_NUM  0       /* SPD on I2C bus 0 */
  61 #define CONFIG_DIMM_SLOTS_PER_CTLR      1
  62
  63
  64 #if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
  65 #define CONFIG_SYS_NOR0_CSPR_EXT        (0x0)
  66 #define CONFIG_SYS_NOR_AMASK            IFC_AMASK(128 * 1024 * 1024)
  67 #define CONFIG_SYS_NOR_AMASK_EARLY      IFC_AMASK(64 * 1024 * 1024)
  68
  69 #define CONFIG_SYS_NOR0_CSPR                                    \
  70         (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS)             | \
  71         CSPR_PORT_SIZE_16                                       | \
  72         CSPR_MSEL_NOR                                           | \
  73         CSPR_V)
  74 #define CONFIG_SYS_NOR0_CSPR_EARLY                              \
  75         (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS_EARLY)       | \
  76         CSPR_PORT_SIZE_16                                       | \
  77         CSPR_MSEL_NOR                                           | \
  78         CSPR_V)
  79 #define CONFIG_SYS_NOR_CSOR     CSOR_NOR_ADM_SHIFT(6)
  80 #define CONFIG_SYS_NOR_FTIM0    (FTIM0_NOR_TACSE(0x1) | \
  81                                 FTIM0_NOR_TEADC(0x1) | \
  82                                 FTIM0_NOR_TEAHC(0x1))
  83 #define CONFIG_SYS_NOR_FTIM1    (FTIM1_NOR_TACO(0x1) | \
  84                                 FTIM1_NOR_TRAD_NOR(0x1))
  85 #define CONFIG_SYS_NOR_FTIM2    (FTIM2_NOR_TCS(0x0) | \
  86                                 FTIM2_NOR_TCH(0x0) | \
  87                                 FTIM2_NOR_TWP(0x1))
  88 #define CONFIG_SYS_NOR_FTIM3    0x04000000
  89 #define CONFIG_SYS_IFC_CCR      0x01000000
  90
  91 #ifndef SYS_NO_FLASH
  92 #define CONFIG_SYS_FLASH_QUIET_TEST
  93 #define CONFIG_FLASH_SHOW_PROGRESS      45 /* count down from 45/5: 9..1 */
  94
  95 #define CONFIG_SYS_MAX_FLASH_BANKS      1       /* number of banks */
  96 #define CONFIG_SYS_MAX_FLASH_SECT       1024    /* sectors per device */
  97 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000   /* Flash Erase Timeout (ms) */
  98 #define CONFIG_SYS_FLASH_WRITE_TOUT     500     /* Flash Write Timeout (ms) */
  99
 100 #define CONFIG_SYS_FLASH_EMPTY_INFO
 101 #define CONFIG_SYS_FLASH_BANKS_LIST     { CONFIG_SYS_FLASH_BASE }
 102 #endif
 103 #endif
 104
 105 #ifndef SPL_NO_IFC
 106 #define CONFIG_NAND_FSL_IFC
 107 #endif
 108
 109 #define CONFIG_SYS_NAND_MAX_ECCPOS      256
 110 #define CONFIG_SYS_NAND_MAX_OOBFREE     2
 111
 112 #define CONFIG_SYS_NAND_CSPR_EXT        (0x0)
 113 #define CONFIG_SYS_NAND_CSPR    (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
 114                                 | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
 115                                 | CSPR_MSEL_NAND        /* MSEL = NAND */ \
 116                                 | CSPR_V)
 117 #define CONFIG_SYS_NAND_AMASK   IFC_AMASK(64 * 1024)
 118
 119 #define CONFIG_SYS_NAND_CSOR    (CSOR_NAND_ECC_ENC_EN   /* ECC on encode */ \
 120                                 | CSOR_NAND_ECC_DEC_EN  /* ECC on decode */ \
 121                                 | CSOR_NAND_ECC_MODE_4  /* 4-bit ECC */ \
 122                                 | CSOR_NAND_RAL_3       /* RAL = 3Byes */ \
 123                                 | CSOR_NAND_PGS_2K      /* Page Size = 2K */ \
 124                                 | CSOR_NAND_SPRZ_64/* Spare size = 64 */ \
 125                                 | CSOR_NAND_PB(64))     /*Pages Per Block = 64*/
 126
 127 #define CONFIG_SYS_NAND_ONFI_DETECTION
 128
 129 /* ONFI NAND Flash mode0 Timing Params */
 130 #define CONFIG_SYS_NAND_FTIM0           (FTIM0_NAND_TCCST(0x07) | \
 131                                         FTIM0_NAND_TWP(0x18)   | \
 132                                         FTIM0_NAND_TWCHT(0x07) | \
 133                                         FTIM0_NAND_TWH(0x0a))
 134 #define CONFIG_SYS_NAND_FTIM1           (FTIM1_NAND_TADLE(0x32) | \
 135                                         FTIM1_NAND_TWBE(0x39)  | \
 136                                         FTIM1_NAND_TRR(0x0e)   | \
 137                                         FTIM1_NAND_TRP(0x18))
 138 #define CONFIG_SYS_NAND_FTIM2           (FTIM2_NAND_TRAD(0x0f) | \
 139                                         FTIM2_NAND_TREH(0x0a) | \
 140                                         FTIM2_NAND_TWHRE(0x1e))
 141 #define CONFIG_SYS_NAND_FTIM3           0x0
 142
 143 #define CONFIG_SYS_NAND_BASE_LIST       { CONFIG_SYS_NAND_BASE }
 144 #define CONFIG_SYS_MAX_NAND_DEVICE      1
 145 #define CONFIG_MTD_NAND_VERIFY_WRITE
 146 #define CONFIG_CMD_NAND
 147
 148 #define CONFIG_SYS_NAND_BLOCK_SIZE      (128 * 1024)
 149
 150 #ifndef SPL_NO_QIXIS
 151 #define CONFIG_FSL_QIXIS
 152 #endif
 153
 154 #define CONFIG_SYS_I2C_FPGA_ADDR        0x66
 155 #define QIXIS_BRDCFG4_OFFSET            0x54
 156 #define QIXIS_LBMAP_SWITCH              2
 157 #define QIXIS_QMAP_MASK                 0xe0
 158 #define QIXIS_QMAP_SHIFT                5
 159 #define QIXIS_LBMAP_MASK                0x1f
 160 #define QIXIS_LBMAP_SHIFT               5
 161 #define QIXIS_LBMAP_DFLTBANK            0x00
 162 #define QIXIS_LBMAP_ALTBANK             0x20
 163 #define QIXIS_LBMAP_SD                  0x00
 164 #define QIXIS_LBMAP_EMMC                0x00
 165 #define QIXIS_LBMAP_SD_QSPI             0x00
 166 #define QIXIS_LBMAP_QSPI                0x00
 167 #define QIXIS_RCW_SRC_SD                0x40
 168 #define QIXIS_RCW_SRC_EMMC              0x41
 169 #define QIXIS_RCW_SRC_QSPI              0x62
 170 #define QIXIS_RST_CTL_RESET             0x31
 171 #define QIXIS_RCFG_CTL_RECONFIG_IDLE    0x20
 172 #define QIXIS_RCFG_CTL_RECONFIG_START   0x21
 173 #define QIXIS_RCFG_CTL_WATCHDOG_ENBLE   0x08
 174 #define QIXIS_RST_FORCE_MEM             0x01
 175
 176 #define CONFIG_SYS_FPGA_CSPR_EXT        (0x0)
 177 #define CONFIG_SYS_FPGA_CSPR            (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS_EARLY) \
 178                                         | CSPR_PORT_SIZE_8 \
 179                                         | CSPR_MSEL_GPCM \
 180                                         | CSPR_V)
 181 #define SYS_FPGA_CSPR_FINAL     (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \
 182                                         | CSPR_PORT_SIZE_8 \
 183                                         | CSPR_MSEL_GPCM \
 184                                         | CSPR_V)
 185
 186 #define CONFIG_SYS_FPGA_AMASK           IFC_AMASK(64*1024)
 187 #define CONFIG_SYS_FPGA_CSOR            CSOR_GPCM_ADM_SHIFT(0)
 188 /* QIXIS Timing parameters*/
 189 #define SYS_FPGA_CS_FTIM0       (FTIM0_GPCM_TACSE(0x0e) | \
 190                                         FTIM0_GPCM_TEADC(0x0e) | \
 191                                         FTIM0_GPCM_TEAHC(0x0e))
 192 #define SYS_FPGA_CS_FTIM1       (FTIM1_GPCM_TACO(0xff) | \
 193                                         FTIM1_GPCM_TRAD(0x3f))
 194 #define SYS_FPGA_CS_FTIM2       (FTIM2_GPCM_TCS(0xf) | \
 195                                         FTIM2_GPCM_TCH(0xf) | \
 196                                         FTIM2_GPCM_TWP(0x3E))
 197 #define SYS_FPGA_CS_FTIM3       0x0
 198
 199 #if defined(CONFIG_TFABOOT) || \
 200         defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
 201 #define CONFIG_SYS_CSPR0_EXT            CONFIG_SYS_NAND_CSPR_EXT
 202 #define CONFIG_SYS_CSPR0                CONFIG_SYS_NAND_CSPR
 203 #define CONFIG_SYS_AMASK0               CONFIG_SYS_NAND_AMASK
 204 #define CONFIG_SYS_CSOR0                CONFIG_SYS_NAND_CSOR
 205 #define CONFIG_SYS_CS0_FTIM0            CONFIG_SYS_NAND_FTIM0
 206 #define CONFIG_SYS_CS0_FTIM1            CONFIG_SYS_NAND_FTIM1
 207 #define CONFIG_SYS_CS0_FTIM2            CONFIG_SYS_NAND_FTIM2
 208 #define CONFIG_SYS_CS0_FTIM3            CONFIG_SYS_NAND_FTIM3
 209 #define CONFIG_SYS_CSPR2_EXT            CONFIG_SYS_FPGA_CSPR_EXT
 210 #define CONFIG_SYS_CSPR2                CONFIG_SYS_FPGA_CSPR
 211 #define CONFIG_SYS_CSPR2_FINAL          SYS_FPGA_CSPR_FINAL
 212 #define CONFIG_SYS_AMASK2               CONFIG_SYS_FPGA_AMASK
 213 #define CONFIG_SYS_CSOR2                CONFIG_SYS_FPGA_CSOR
 214 #define CONFIG_SYS_CS2_FTIM0            SYS_FPGA_CS_FTIM0
 215 #define CONFIG_SYS_CS2_FTIM1            SYS_FPGA_CS_FTIM1
 216 #define CONFIG_SYS_CS2_FTIM2            SYS_FPGA_CS_FTIM2
 217 #define CONFIG_SYS_CS2_FTIM3            SYS_FPGA_CS_FTIM3
 218 #else
 219 #define CONFIG_SYS_CSPR0_EXT            CONFIG_SYS_NOR0_CSPR_EXT
 220 #define CONFIG_SYS_CSPR0                CONFIG_SYS_NOR0_CSPR_EARLY
 221 #define CONFIG_SYS_CSPR0_FINAL          CONFIG_SYS_NOR0_CSPR
 222 #define CONFIG_SYS_AMASK0               CONFIG_SYS_NOR_AMASK
 223 #define CONFIG_SYS_CSOR0                CONFIG_SYS_NOR_CSOR
 224 #define CONFIG_SYS_CS0_FTIM0            CONFIG_SYS_NOR_FTIM0
 225 #define CONFIG_SYS_CS0_FTIM1            CONFIG_SYS_NOR_FTIM1
 226 #define CONFIG_SYS_CS0_FTIM2            CONFIG_SYS_NOR_FTIM2
 227 #define CONFIG_SYS_CS0_FTIM3            CONFIG_SYS_NOR_FTIM3
 228 #endif
 229
 230 #define CONFIG_SYS_LS_MC_BOOT_TIMEOUT_MS 5000
 231
 232 #define I2C_MUX_CH_VOL_MONITOR          0xA
 233 /* Voltage monitor on channel 2*/
 234 #define I2C_VOL_MONITOR_ADDR           0x63
 235 #define I2C_VOL_MONITOR_BUS_V_OFFSET   0x2
 236 #define I2C_VOL_MONITOR_BUS_V_OVF      0x1
 237 #define I2C_VOL_MONITOR_BUS_V_SHIFT    3
 238 #define I2C_SVDD_MONITOR_ADDR           0x4F
 239
 240 #define CONFIG_VID_FLS_ENV              "ls1088ardb_vdd_mv"
 241 #define CONFIG_VID
 242
 243 /* The lowest and highest voltage allowed for LS1088ARDB */
 244 #define VDD_MV_MIN                      819
 245 #define VDD_MV_MAX                      1212
 246
 247 #define CONFIG_VOL_MONITOR_LTC3882_SET
 248 #define CONFIG_VOL_MONITOR_LTC3882_READ
 249
 250 /* PM Bus commands code for LTC3882*/
 251 #define PMBUS_CMD_PAGE                  0x0
 252 #define PMBUS_CMD_READ_VOUT             0x8B
 253 #define PMBUS_CMD_PAGE_PLUS_WRITE       0x05
 254 #define PMBUS_CMD_VOUT_COMMAND          0x21
 255
 256 #define PWM_CHANNEL0                    0x0
 257
 258 /*
 259  * I2C bus multiplexer
 260  */
 261 #define I2C_MUX_PCA_ADDR_PRI            0x77
 262 #define I2C_MUX_PCA_ADDR_SEC            0x76 /* Secondary multiplexer */
 263 #define I2C_RETIMER_ADDR                0x18
 264 #define I2C_MUX_CH_DEFAULT              0x8
 265 #define I2C_MUX_CH5                     0xD
 266
 267 #ifndef SPL_NO_RTC
 268 /*
 269 * RTC configuration
 270 */
 271 #define RTC
 272 #define CONFIG_SYS_I2C_RTC_ADDR         0x51  /* Channel 3*/
 273 #endif
 274
 275 /* EEPROM */
 276 #define CONFIG_ID_EEPROM
 277 #define CONFIG_SYS_I2C_EEPROM_NXID
 278 #define CONFIG_SYS_EEPROM_BUS_NUM               0
 279 #define CONFIG_SYS_I2C_EEPROM_ADDR              0x57
 280 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN          1
 281 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS       3
 282 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS   5
 283
 284 #ifndef SPL_NO_QSPI
 285 /* QSPI device */
 286 #if defined(CONFIG_TFABOOT) || \
 287         defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
 288 #define FSL_QSPI_FLASH_SIZE             (1 << 26)
 289 #define FSL_QSPI_FLASH_NUM              2
 290 #endif
 291 #endif
 292
 293 #define CONFIG_CMD_MEMINFO
 294 #define CONFIG_SYS_MEMTEST_START        0x80000000
 295 #define CONFIG_SYS_MEMTEST_END          0x9fffffff
 296
 297 #ifdef CONFIG_SPL_BUILD
 298 #define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE
 299 #else
 300 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
 301 #endif
 302
 303 #define CONFIG_FSL_MEMAC
 304
 305 #ifndef SPL_NO_ENV
 306 /* Initial environment variables */
 307 #ifdef CONFIG_TFABOOT
 308 #define QSPI_MC_INIT_CMD                                \
 309         "sf probe 0:0;sf read 0x80000000 0xA00000 0x100000;"    \
 310         "sf read 0x80100000 0xE00000 0x100000;"                         \
 311         "env exists secureboot && "                     \
 312         "sf read 0x80700000 0x700000 0x40000 && "       \
 313         "sf read 0x80740000 0x740000 0x40000 && "       \
 314         "esbc_validate 0x80700000 && "                  \
 315         "esbc_validate 0x80740000 ;"                    \
 316         "fsl_mc start mc 0x80000000 0x80100000\0"
 317 #define SD_MC_INIT_CMD                          \
 318         "mmcinfo;mmc read 0x80000000 0x5000 0x800;"             \
 319         "mmc read 0x80100000 0x7000 0x800;"                             \
 320         "env exists secureboot && "                     \
 321         "mmc read 0x80700000 0x3800 0x10 && "           \
 322         "mmc read 0x80740000 0x3A00 0x10 && "           \
 323         "esbc_validate 0x80700000 && "                  \
 324         "esbc_validate 0x80740000 ;"                    \
 325         "fsl_mc start mc 0x80000000 0x80100000\0"
 326 #else
 327 #if defined(CONFIG_QSPI_BOOT)
 328 #define MC_INIT_CMD                             \
 329         "mcinitcmd=sf probe 0:0;sf read 0x80000000 0xA00000 0x100000;"  \
 330         "sf read 0x80100000 0xE00000 0x100000;"                         \
 331         "env exists secureboot && "                     \
 332         "sf read 0x80700000 0x700000 0x40000 && "       \
 333         "sf read 0x80740000 0x740000 0x40000 && "       \
 334         "esbc_validate 0x80700000 && "                  \
 335         "esbc_validate 0x80740000 ;"                    \
 336         "fsl_mc start mc 0x80000000 0x80100000\0"       \
 337         "mcmemsize=0x70000000\0"
 338 #elif defined(CONFIG_SD_BOOT)
 339 #define MC_INIT_CMD                             \
 340         "mcinitcmd=mmcinfo;mmc read 0x80000000 0x5000 0x800;"           \
 341         "mmc read 0x80100000 0x7000 0x800;"                             \
 342         "env exists secureboot && "                     \
 343         "mmc read 0x80700000 0x3800 0x10 && "           \
 344         "mmc read 0x80740000 0x3A00 0x10 && "           \
 345         "esbc_validate 0x80700000 && "                  \
 346         "esbc_validate 0x80740000 ;"                    \
 347         "fsl_mc start mc 0x80000000 0x80100000\0"       \
 348         "mcmemsize=0x70000000\0"
 349 #endif
 350 #endif /* CONFIG_TFABOOT */
 351
 352 #undef CONFIG_EXTRA_ENV_SETTINGS
 353 #ifdef CONFIG_TFABOOT
 354 #define CONFIG_EXTRA_ENV_SETTINGS               \
 355         "BOARD=ls1088ardb\0"                    \
 356         "hwconfig=fsl_ddr:bank_intlv=auto\0"    \
 357         "ramdisk_addr=0x800000\0"               \
 358         "ramdisk_size=0x2000000\0"              \
 359         "fdt_high=0xa0000000\0"                 \
 360         "initrd_high=0xffffffffffffffff\0"      \
 361         "fdt_addr=0x64f00000\0"                 \
 362         "kernel_addr=0x1000000\0"               \
 363         "kernel_addr_sd=0x8000\0"               \
 364         "kernelhdr_addr_sd=0x4000\0"            \
 365         "kernel_start=0x580100000\0"            \
 366         "kernelheader_start=0x580800000\0"      \
 367         "scriptaddr=0x80000000\0"               \
 368         "scripthdraddr=0x80080000\0"            \
 369         "fdtheader_addr_r=0x80100000\0"         \
 370         "kernelheader_addr=0x800000\0"          \
 371         "kernelheader_addr_r=0x80200000\0"      \
 372         "kernel_addr_r=0x81000000\0"            \
 373         "kernelheader_size=0x40000\0"           \
 374         "fdt_addr_r=0x90000000\0"               \
 375         "load_addr=0xa0000000\0"                \
 376         "kernel_size=0x2800000\0"               \
 377         "kernel_size_sd=0x14000\0"              \
 378         "kernelhdr_size_sd=0x10\0"              \
 379         QSPI_MC_INIT_CMD                        \
 380         "mcmemsize=0x70000000\0"                \
 381         BOOTENV                                 \
 382         "boot_scripts=ls1088ardb_boot.scr\0"    \
 383         "boot_script_hdr=hdr_ls1088ardb_bs.out\0"       \
 384         "scan_dev_for_boot_part="               \
 385                 "part list ${devtype} ${devnum} devplist; "     \
 386                 "env exists devplist || setenv devplist 1; "    \
 387                 "for distro_bootpart in ${devplist}; do "       \
 388                         "if fstype ${devtype} "                 \
 389                                 "${devnum}:${distro_bootpart} " \
 390                                 "bootfstype; then "             \
 391                                 "run scan_dev_for_boot; "       \
 392                         "fi; "                                  \
 393                 "done\0"                                        \
 394         "boot_a_script="                                        \
 395                 "load ${devtype} ${devnum}:${distro_bootpart} " \
 396                 "${scriptaddr} ${prefix}${script}; "            \
 397         "env exists secureboot && load ${devtype} "             \
 398                 "${devnum}:${distro_bootpart} "                 \
 399                 "${scripthdraddr} ${prefix}${boot_script_hdr}; "\
 400                 "env exists secureboot "                        \
 401                 "&& esbc_validate ${scripthdraddr};"            \
 402                 "source ${scriptaddr}\0"                        \
 403         "installer=load mmc 0:2 $load_addr "                    \
 404                 "/flex_installer_arm64.itb; "                   \
 405                 "env exists mcinitcmd && run mcinitcmd && "     \
 406                 "mmc read 0x80001000 0x6800 0x800;"             \
 407                 "fsl_mc lazyapply dpl 0x80001000;"                      \
 408                 "bootm $load_addr#ls1088ardb\0"                 \
 409         "qspi_bootcmd=echo Trying load from qspi..;"            \
 410                 "sf probe && sf read $load_addr "               \
 411                 "$kernel_addr $kernel_size ; env exists secureboot "    \
 412                 "&& sf read $kernelheader_addr_r $kernelheader_addr "   \
 413                 "$kernelheader_size && esbc_validate ${kernelheader_addr_r}; "\
 414                 "bootm $load_addr#$BOARD\0"                     \
 415                 "sd_bootcmd=echo Trying load from sd card..;"           \
 416                 "mmcinfo; mmc read $load_addr "                 \
 417                 "$kernel_addr_sd $kernel_size_sd ;"             \
 418                 "env exists secureboot && mmc read $kernelheader_addr_r "\
 419                 "$kernelhdr_addr_sd $kernelhdr_size_sd "        \
 420                 " && esbc_validate ${kernelheader_addr_r};"     \
 421                 "bootm $load_addr#$BOARD\0"
 422 #else
 423 #define CONFIG_EXTRA_ENV_SETTINGS               \
 424         "BOARD=ls1088ardb\0"                    \
 425         "hwconfig=fsl_ddr:bank_intlv=auto\0"    \
 426         "ramdisk_addr=0x800000\0"               \
 427         "ramdisk_size=0x2000000\0"              \
 428         "fdt_high=0xa0000000\0"                 \
 429         "initrd_high=0xffffffffffffffff\0"      \
 430         "fdt_addr=0x64f00000\0"                 \
 431         "kernel_addr=0x1000000\0"               \
 432         "kernel_addr_sd=0x8000\0"               \
 433         "kernelhdr_addr_sd=0x4000\0"            \
 434         "kernel_start=0x580100000\0"            \
 435         "kernelheader_start=0x580800000\0"      \
 436         "scriptaddr=0x80000000\0"               \
 437         "scripthdraddr=0x80080000\0"            \
 438         "fdtheader_addr_r=0x80100000\0"         \
 439         "kernelheader_addr=0x800000\0"          \
 440         "kernelheader_addr_r=0x80200000\0"      \
 441         "kernel_addr_r=0x81000000\0"            \
 442         "kernelheader_size=0x40000\0"           \
 443         "fdt_addr_r=0x90000000\0"               \
 444         "load_addr=0xa0000000\0"                \
 445         "kernel_size=0x2800000\0"               \
 446         "kernel_size_sd=0x14000\0"              \
 447         "kernelhdr_size_sd=0x10\0"              \
 448         MC_INIT_CMD                             \
 449         BOOTENV                                 \
 450         "boot_scripts=ls1088ardb_boot.scr\0"    \
 451         "boot_script_hdr=hdr_ls1088ardb_bs.out\0"       \
 452         "scan_dev_for_boot_part="               \
 453                 "part list ${devtype} ${devnum} devplist; "     \
 454                 "env exists devplist || setenv devplist 1; "    \
 455                 "for distro_bootpart in ${devplist}; do "       \
 456                         "if fstype ${devtype} "                 \
 457                                 "${devnum}:${distro_bootpart} " \
 458                                 "bootfstype; then "             \
 459                                 "run scan_dev_for_boot; "       \
 460                         "fi; "                                  \
 461                 "done\0"                                        \
 462         "boot_a_script="                                        \
 463                 "load ${devtype} ${devnum}:${distro_bootpart} " \
 464                 "${scriptaddr} ${prefix}${script}; "            \
 465         "env exists secureboot && load ${devtype} "             \
 466                 "${devnum}:${distro_bootpart} "                 \
 467                 "${scripthdraddr} ${prefix}${boot_script_hdr} " \
 468                 "&& esbc_validate ${scripthdraddr};"            \
 469                 "source ${scriptaddr}\0"                        \
 470         "installer=load mmc 0:2 $load_addr "                    \
 471                 "/flex_installer_arm64.itb; "                   \
 472                 "env exists mcinitcmd && run mcinitcmd && "     \
 473                 "mmc read 0x80001000 0x6800 0x800;"             \
 474                 "fsl_mc lazyapply dpl 0x80001000;"                      \
 475                 "bootm $load_addr#ls1088ardb\0"                 \
 476         "qspi_bootcmd=echo Trying load from qspi..;"            \
 477                 "sf probe && sf read $load_addr "               \
 478                 "$kernel_addr $kernel_size ; env exists secureboot "    \
 479                 "&& sf read $kernelheader_addr_r $kernelheader_addr "   \
 480                 "$kernelheader_size && esbc_validate ${kernelheader_addr_r}; "\
 481                 "bootm $load_addr#$BOARD\0"                     \
 482                 "sd_bootcmd=echo Trying load from sd card..;"           \
 483                 "mmcinfo; mmc read $load_addr "                 \
 484                 "$kernel_addr_sd $kernel_size_sd ;"             \
 485                 "env exists secureboot && mmc read $kernelheader_addr_r "\
 486                 "$kernelhdr_addr_sd $kernelhdr_size_sd "        \
 487                 " && esbc_validate ${kernelheader_addr_r};"     \
 488                 "bootm $load_addr#$BOARD\0"
 489 #endif /* CONFIG_TFABOOT */
 490
 491 #undef CONFIG_BOOTCOMMAND
 492 #ifdef CONFIG_TFABOOT
 493 #define QSPI_NOR_BOOTCOMMAND                                    \
 494                 "sf read 0x80001000 0xd00000 0x100000;"         \
 495                 "env exists mcinitcmd && env exists secureboot "        \
 496                 " && sf read 0x80780000 0x780000 0x100000 "     \
 497                 "&& esbc_validate 0x80780000;env exists mcinitcmd "     \
 498                 "&& fsl_mc lazyapply dpl 0x80001000;"           \
 499                 "run distro_bootcmd;run qspi_bootcmd;"          \
 500                 "env exists secureboot && esbc_halt;"
 501 #define SD_BOOTCOMMAND                                          \
 502                 "env exists mcinitcmd && mmcinfo; "             \
 503                 "mmc read 0x80001000 0x6800 0x800; "            \
 504                 "env exists mcinitcmd && env exists secureboot "        \
 505                 " && mmc read 0x80780000 0x3C00 0x10 "          \
 506                 "&& esbc_validate 0x80780000;env exists mcinitcmd "     \
 507                 "&& fsl_mc lazyapply dpl 0x80001000;"           \
 508                 "run distro_bootcmd;run sd_bootcmd;"            \
 509                 "env exists secureboot && esbc_halt;"
 510 #else
 511 #if defined(CONFIG_QSPI_BOOT)
 512 /* Try to boot an on-QSPI kernel first, then do normal distro boot */
 513 #define CONFIG_BOOTCOMMAND                                      \
 514                 "sf read 0x80001000 0xd00000 0x100000;"         \
 515                 "env exists mcinitcmd && env exists secureboot "        \
 516                 " && sf read 0x80780000 0x780000 0x100000 "     \
 517                 "&& esbc_validate 0x80780000;env exists mcinitcmd "     \
 518                 "&& fsl_mc lazyapply dpl 0x80001000;"           \
 519                 "run distro_bootcmd;run qspi_bootcmd;"          \
 520                 "env exists secureboot && esbc_halt;"
 521
 522 /* Try to boot an on-SD kernel first, then do normal distro boot */
 523 #elif defined(CONFIG_SD_BOOT)
 524 #define CONFIG_BOOTCOMMAND                                      \
 525                 "env exists mcinitcmd && mmcinfo; "             \
 526                 "mmc read 0x80001000 0x6800 0x800; "            \
 527                 "env exists mcinitcmd && env exists secureboot "        \
 528                 " && mmc read 0x80780000 0x3C00 0x10 "          \
 529                 "&& esbc_validate 0x80780000;env exists mcinitcmd "     \
 530                 "&& fsl_mc lazyapply dpl 0x80001000;"           \
 531                 "run distro_bootcmd;run sd_bootcmd;"            \
 532                 "env exists secureboot && esbc_halt;"
 533 #endif
 534 #endif /* CONFIG_TFABOOT */
 535
 536 /* MAC/PHY configuration */
 537 #ifdef CONFIG_FSL_MC_ENET
 538 #define CONFIG_PHYLIB
 539
 540 #define CONFIG_PHY_VITESSE
 541 #define AQ_PHY_ADDR1                    0x00
 542 #define AQR105_IRQ_MASK                 0x00000004
 543
 544 #define QSGMII1_PORT1_PHY_ADDR          0x0c
 545 #define QSGMII1_PORT2_PHY_ADDR          0x0d
 546 #define QSGMII1_PORT3_PHY_ADDR          0x0e
 547 #define QSGMII1_PORT4_PHY_ADDR          0x0f
 548 #define QSGMII2_PORT1_PHY_ADDR          0x1c
 549 #define QSGMII2_PORT2_PHY_ADDR          0x1d
 550 #define QSGMII2_PORT3_PHY_ADDR          0x1e
 551 #define QSGMII2_PORT4_PHY_ADDR          0x1f
 552
 553 #define CONFIG_ETHPRIME         "DPMAC1@xgmii"
 554 #define CONFIG_PHY_GIGE
 555 #endif
 556 #endif
 557
 558 /*  MMC  */
 559 #ifdef CONFIG_MMC
 560 #define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
 561 #endif
 562
 563 #ifndef SPL_NO_ENV
 564
 565 #define BOOT_TARGET_DEVICES(func) \
 566         func(MMC, mmc, 0) \
 567         func(SCSI, scsi, 0) \
 568         func(DHCP, dhcp, na)
 569 #include <config_distro_bootcmd.h>
 570 #endif
 571
 572 #include <asm/fsl_secure_boot.h>
 573
 574 #endif /* __LS1088A_RDB_H */