include/configs/ls1088ardb.h

   1 /* SPDX-License-Identifier: GPL-2.0+ */
   2 /*
   3  * Copyright 2017 NXP
   4  */
   5
   6 #ifndef __LS1088A_RDB_H
   7 #define __LS1088A_RDB_H
   8
   9 #include "ls1088a_common.h"
  10
  11 #if defined(CONFIG_QSPI_BOOT)
  12 #define CONFIG_ENV_SIZE                 0x2000          /* 8KB */
  13 #define CONFIG_ENV_SECT_SIZE            0x40000
  14 #elif defined(CONFIG_SD_BOOT)
  15 #define CONFIG_ENV_OFFSET               (3 * 1024 * 1024)
  16 #define CONFIG_SYS_MMC_ENV_DEV          0
  17 #define CONFIG_ENV_SIZE                 0x2000
  18 #else
  19 #define CONFIG_ENV_IS_IN_FLASH
  20 #define CONFIG_ENV_ADDR                 (CONFIG_SYS_FLASH_BASE + 0x300000)
  21 #define CONFIG_ENV_SECT_SIZE            0x20000
  22 #define CONFIG_ENV_SIZE                 0x20000
  23 #endif
  24
  25 #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
  26 #ifndef CONFIG_SPL_BUILD
  27 #define CONFIG_QIXIS_I2C_ACCESS
  28 #endif
  29 #define SYS_NO_FLASH
  30 #undef CONFIG_CMD_IMLS
  31 #endif
  32
  33 #define CONFIG_SYS_CLK_FREQ             100000000
  34 #define CONFIG_DDR_CLK_FREQ             100000000
  35 #define COUNTER_FREQUENCY_REAL          25000000        /* 25MHz */
  36 #define COUNTER_FREQUENCY               25000000        /* 25MHz */
  37
  38 #define CONFIG_DDR_SPD
  39 #ifdef CONFIG_EMU
  40 #define CONFIG_SYS_FSL_DDR_EMU
  41 #define CONFIG_SYS_MXC_I2C1_SPEED       40000000
  42 #define CONFIG_SYS_MXC_I2C2_SPEED       40000000
  43 #else
  44 #define CONFIG_DDR_ECC
  45 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
  46 #define CONFIG_MEM_INIT_VALUE           0xdeadbeef
  47 #endif
  48 #define SPD_EEPROM_ADDRESS      0x51
  49 #define CONFIG_SYS_SPD_BUS_NUM  0       /* SPD on I2C bus 0 */
  50 #define CONFIG_DIMM_SLOTS_PER_CTLR      1
  51
  52
  53 #if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
  54 #define CONFIG_SYS_NOR0_CSPR_EXT        (0x0)
  55 #define CONFIG_SYS_NOR_AMASK            IFC_AMASK(128 * 1024 * 1024)
  56 #define CONFIG_SYS_NOR_AMASK_EARLY      IFC_AMASK(64 * 1024 * 1024)
  57
  58 #define CONFIG_SYS_NOR0_CSPR                                    \
  59         (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS)             | \
  60         CSPR_PORT_SIZE_16                                       | \
  61         CSPR_MSEL_NOR                                           | \
  62         CSPR_V)
  63 #define CONFIG_SYS_NOR0_CSPR_EARLY                              \
  64         (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS_EARLY)       | \
  65         CSPR_PORT_SIZE_16                                       | \
  66         CSPR_MSEL_NOR                                           | \
  67         CSPR_V)
  68 #define CONFIG_SYS_NOR_CSOR     CSOR_NOR_ADM_SHIFT(6)
  69 #define CONFIG_SYS_NOR_FTIM0    (FTIM0_NOR_TACSE(0x1) | \
  70                                 FTIM0_NOR_TEADC(0x1) | \
  71                                 FTIM0_NOR_TEAHC(0x1))
  72 #define CONFIG_SYS_NOR_FTIM1    (FTIM1_NOR_TACO(0x1) | \
  73                                 FTIM1_NOR_TRAD_NOR(0x1))
  74 #define CONFIG_SYS_NOR_FTIM2    (FTIM2_NOR_TCS(0x0) | \
  75                                 FTIM2_NOR_TCH(0x0) | \
  76                                 FTIM2_NOR_TWP(0x1))
  77 #define CONFIG_SYS_NOR_FTIM3    0x04000000
  78 #define CONFIG_SYS_IFC_CCR      0x01000000
  79
  80 #ifndef SYS_NO_FLASH
  81 #define CONFIG_SYS_FLASH_QUIET_TEST
  82 #define CONFIG_FLASH_SHOW_PROGRESS      45 /* count down from 45/5: 9..1 */
  83
  84 #define CONFIG_SYS_MAX_FLASH_BANKS      1       /* number of banks */
  85 #define CONFIG_SYS_MAX_FLASH_SECT       1024    /* sectors per device */
  86 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000   /* Flash Erase Timeout (ms) */
  87 #define CONFIG_SYS_FLASH_WRITE_TOUT     500     /* Flash Write Timeout (ms) */
  88
  89 #define CONFIG_SYS_FLASH_EMPTY_INFO
  90 #define CONFIG_SYS_FLASH_BANKS_LIST     { CONFIG_SYS_FLASH_BASE }
  91 #endif
  92 #endif
  93
  94 #ifndef SPL_NO_IFC
  95 #define CONFIG_NAND_FSL_IFC
  96 #endif
  97
  98 #define CONFIG_SYS_NAND_MAX_ECCPOS      256
  99 #define CONFIG_SYS_NAND_MAX_OOBFREE     2
 100
 101 #define CONFIG_SYS_NAND_CSPR_EXT        (0x0)
 102 #define CONFIG_SYS_NAND_CSPR    (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
 103                                 | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
 104                                 | CSPR_MSEL_NAND        /* MSEL = NAND */ \
 105                                 | CSPR_V)
 106 #define CONFIG_SYS_NAND_AMASK   IFC_AMASK(64 * 1024)
 107
 108 #define CONFIG_SYS_NAND_CSOR    (CSOR_NAND_ECC_ENC_EN   /* ECC on encode */ \
 109                                 | CSOR_NAND_ECC_DEC_EN  /* ECC on decode */ \
 110                                 | CSOR_NAND_ECC_MODE_4  /* 4-bit ECC */ \
 111                                 | CSOR_NAND_RAL_3       /* RAL = 3Byes */ \
 112                                 | CSOR_NAND_PGS_2K      /* Page Size = 2K */ \
 113                                 | CSOR_NAND_SPRZ_64/* Spare size = 64 */ \
 114                                 | CSOR_NAND_PB(64))     /*Pages Per Block = 64*/
 115
 116 #define CONFIG_SYS_NAND_ONFI_DETECTION
 117
 118 /* ONFI NAND Flash mode0 Timing Params */
 119 #define CONFIG_SYS_NAND_FTIM0           (FTIM0_NAND_TCCST(0x07) | \
 120                                         FTIM0_NAND_TWP(0x18)   | \
 121                                         FTIM0_NAND_TWCHT(0x07) | \
 122                                         FTIM0_NAND_TWH(0x0a))
 123 #define CONFIG_SYS_NAND_FTIM1           (FTIM1_NAND_TADLE(0x32) | \
 124                                         FTIM1_NAND_TWBE(0x39)  | \
 125                                         FTIM1_NAND_TRR(0x0e)   | \
 126                                         FTIM1_NAND_TRP(0x18))
 127 #define CONFIG_SYS_NAND_FTIM2           (FTIM2_NAND_TRAD(0x0f) | \
 128                                         FTIM2_NAND_TREH(0x0a) | \
 129                                         FTIM2_NAND_TWHRE(0x1e))
 130 #define CONFIG_SYS_NAND_FTIM3           0x0
 131
 132 #define CONFIG_SYS_NAND_BASE_LIST       { CONFIG_SYS_NAND_BASE }
 133 #define CONFIG_SYS_MAX_NAND_DEVICE      1
 134 #define CONFIG_MTD_NAND_VERIFY_WRITE
 135 #define CONFIG_CMD_NAND
 136
 137 #define CONFIG_SYS_NAND_BLOCK_SIZE      (128 * 1024)
 138
 139 #ifndef SPL_NO_QIXIS
 140 #define CONFIG_FSL_QIXIS
 141 #endif
 142
 143 #define CONFIG_SYS_I2C_FPGA_ADDR        0x66
 144 #define QIXIS_BRDCFG4_OFFSET            0x54
 145 #define QIXIS_LBMAP_SWITCH              2
 146 #define QIXIS_QMAP_MASK                 0xe0
 147 #define QIXIS_QMAP_SHIFT                5
 148 #define QIXIS_LBMAP_MASK                0x1f
 149 #define QIXIS_LBMAP_SHIFT               5
 150 #define QIXIS_LBMAP_DFLTBANK            0x00
 151 #define QIXIS_LBMAP_ALTBANK             0x20
 152 #define QIXIS_LBMAP_SD                  0x00
 153 #define QIXIS_LBMAP_EMMC                0x00
 154 #define QIXIS_LBMAP_SD_QSPI             0x00
 155 #define QIXIS_LBMAP_QSPI                0x00
 156 #define QIXIS_RCW_SRC_SD                0x40
 157 #define QIXIS_RCW_SRC_EMMC              0x41
 158 #define QIXIS_RCW_SRC_QSPI              0x62
 159 #define QIXIS_RST_CTL_RESET             0x31
 160 #define QIXIS_RCFG_CTL_RECONFIG_IDLE    0x20
 161 #define QIXIS_RCFG_CTL_RECONFIG_START   0x21
 162 #define QIXIS_RCFG_CTL_WATCHDOG_ENBLE   0x08
 163 #define QIXIS_RST_FORCE_MEM             0x01
 164
 165 #define CONFIG_SYS_FPGA_CSPR_EXT        (0x0)
 166 #define CONFIG_SYS_FPGA_CSPR            (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS_EARLY) \
 167                                         | CSPR_PORT_SIZE_8 \
 168                                         | CSPR_MSEL_GPCM \
 169                                         | CSPR_V)
 170 #define SYS_FPGA_CSPR_FINAL     (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \
 171                                         | CSPR_PORT_SIZE_8 \
 172                                         | CSPR_MSEL_GPCM \
 173                                         | CSPR_V)
 174
 175 #define CONFIG_SYS_FPGA_AMASK           IFC_AMASK(64*1024)
 176 #define CONFIG_SYS_FPGA_CSOR            CSOR_GPCM_ADM_SHIFT(0)
 177 /* QIXIS Timing parameters*/
 178 #define SYS_FPGA_CS_FTIM0       (FTIM0_GPCM_TACSE(0x0e) | \
 179                                         FTIM0_GPCM_TEADC(0x0e) | \
 180                                         FTIM0_GPCM_TEAHC(0x0e))
 181 #define SYS_FPGA_CS_FTIM1       (FTIM1_GPCM_TACO(0xff) | \
 182                                         FTIM1_GPCM_TRAD(0x3f))
 183 #define SYS_FPGA_CS_FTIM2       (FTIM2_GPCM_TCS(0xf) | \
 184                                         FTIM2_GPCM_TCH(0xf) | \
 185                                         FTIM2_GPCM_TWP(0x3E))
 186 #define SYS_FPGA_CS_FTIM3       0x0
 187
 188 #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
 189 #define CONFIG_SYS_CSPR0_EXT            CONFIG_SYS_NAND_CSPR_EXT
 190 #define CONFIG_SYS_CSPR0                CONFIG_SYS_NAND_CSPR
 191 #define CONFIG_SYS_AMASK0               CONFIG_SYS_NAND_AMASK
 192 #define CONFIG_SYS_CSOR0                CONFIG_SYS_NAND_CSOR
 193 #define CONFIG_SYS_CS0_FTIM0            CONFIG_SYS_NAND_FTIM0
 194 #define CONFIG_SYS_CS0_FTIM1            CONFIG_SYS_NAND_FTIM1
 195 #define CONFIG_SYS_CS0_FTIM2            CONFIG_SYS_NAND_FTIM2
 196 #define CONFIG_SYS_CS0_FTIM3            CONFIG_SYS_NAND_FTIM3
 197 #define CONFIG_SYS_CSPR2_EXT            CONFIG_SYS_FPGA_CSPR_EXT
 198 #define CONFIG_SYS_CSPR2                CONFIG_SYS_FPGA_CSPR
 199 #define CONFIG_SYS_CSPR2_FINAL          SYS_FPGA_CSPR_FINAL
 200 #define CONFIG_SYS_AMASK2               CONFIG_SYS_FPGA_AMASK
 201 #define CONFIG_SYS_CSOR2                CONFIG_SYS_FPGA_CSOR
 202 #define CONFIG_SYS_CS2_FTIM0            SYS_FPGA_CS_FTIM0
 203 #define CONFIG_SYS_CS2_FTIM1            SYS_FPGA_CS_FTIM1
 204 #define CONFIG_SYS_CS2_FTIM2            SYS_FPGA_CS_FTIM2
 205 #define CONFIG_SYS_CS2_FTIM3            SYS_FPGA_CS_FTIM3
 206 #else
 207 #define CONFIG_SYS_CSPR0_EXT            CONFIG_SYS_NOR0_CSPR_EXT
 208 #define CONFIG_SYS_CSPR0                CONFIG_SYS_NOR0_CSPR_EARLY
 209 #define CONFIG_SYS_CSPR0_FINAL          CONFIG_SYS_NOR0_CSPR
 210 #define CONFIG_SYS_AMASK0               CONFIG_SYS_NOR_AMASK
 211 #define CONFIG_SYS_CSOR0                CONFIG_SYS_NOR_CSOR
 212 #define CONFIG_SYS_CS0_FTIM0            CONFIG_SYS_NOR_FTIM0
 213 #define CONFIG_SYS_CS0_FTIM1            CONFIG_SYS_NOR_FTIM1
 214 #define CONFIG_SYS_CS0_FTIM2            CONFIG_SYS_NOR_FTIM2
 215 #define CONFIG_SYS_CS0_FTIM3            CONFIG_SYS_NOR_FTIM3
 216 #endif
 217
 218
 219 #define CONFIG_SYS_LS_MC_BOOT_TIMEOUT_MS 5000
 220
 221 #define I2C_MUX_CH_VOL_MONITOR          0xA
 222 /* Voltage monitor on channel 2*/
 223 #define I2C_VOL_MONITOR_ADDR           0x63
 224 #define I2C_VOL_MONITOR_BUS_V_OFFSET   0x2
 225 #define I2C_VOL_MONITOR_BUS_V_OVF      0x1
 226 #define I2C_VOL_MONITOR_BUS_V_SHIFT    3
 227 #define I2C_SVDD_MONITOR_ADDR           0x4F
 228
 229 #define CONFIG_VID_FLS_ENV              "ls1088ardb_vdd_mv"
 230 #define CONFIG_VID
 231
 232 /* The lowest and highest voltage allowed for LS1088ARDB */
 233 #define VDD_MV_MIN                      819
 234 #define VDD_MV_MAX                      1212
 235
 236 #define CONFIG_VOL_MONITOR_LTC3882_SET
 237 #define CONFIG_VOL_MONITOR_LTC3882_READ
 238
 239 /* PM Bus commands code for LTC3882*/
 240 #define PMBUS_CMD_PAGE                  0x0
 241 #define PMBUS_CMD_READ_VOUT             0x8B
 242 #define PMBUS_CMD_PAGE_PLUS_WRITE       0x05
 243 #define PMBUS_CMD_VOUT_COMMAND          0x21
 244
 245 #define PWM_CHANNEL0                    0x0
 246
 247 /*
 248  * I2C bus multiplexer
 249  */
 250 #define I2C_MUX_PCA_ADDR_PRI            0x77
 251 #define I2C_MUX_PCA_ADDR_SEC            0x76 /* Secondary multiplexer */
 252 #define I2C_RETIMER_ADDR                0x18
 253 #define I2C_MUX_CH_DEFAULT              0x8
 254 #define I2C_MUX_CH5                     0xD
 255
 256 #ifndef SPL_NO_RTC
 257 /*
 258 * RTC configuration
 259 */
 260 #define RTC
 261 #define CONFIG_RTC_PCF8563 1
 262 #define CONFIG_SYS_I2C_RTC_ADDR         0x51  /* Channel 3*/
 263 #define CONFIG_CMD_DATE
 264 #endif
 265
 266 /* EEPROM */
 267 #define CONFIG_ID_EEPROM
 268 #define CONFIG_SYS_I2C_EEPROM_NXID
 269 #define CONFIG_SYS_EEPROM_BUS_NUM               0
 270 #define CONFIG_SYS_I2C_EEPROM_ADDR              0x57
 271 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN          1
 272 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS       3
 273 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS   5
 274
 275 #ifndef SPL_NO_QSPI
 276 /* QSPI device */
 277 #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
 278 #define FSL_QSPI_FLASH_SIZE             (1 << 26)
 279 #define FSL_QSPI_FLASH_NUM              2
 280 #endif
 281 #endif
 282
 283 #define CONFIG_CMD_MEMINFO
 284 #define CONFIG_SYS_MEMTEST_START        0x80000000
 285 #define CONFIG_SYS_MEMTEST_END          0x9fffffff
 286
 287 #ifdef CONFIG_SPL_BUILD
 288 #define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE
 289 #else
 290 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
 291 #endif
 292
 293 #define CONFIG_FSL_MEMAC
 294
 295 #ifndef SPL_NO_ENV
 296 /* Initial environment variables */
 297 #if defined(CONFIG_QSPI_BOOT)
 298 #define MC_INIT_CMD                             \
 299         "mcinitcmd=sf probe 0:0;sf read 0x80000000 0xA00000 0x100000;"  \
 300         "sf read 0x80100000 0xE00000 0x100000;"                         \
 301         "env exists secureboot && "                     \
 302         "sf read 0x80700000 0x700000 0x40000 && "       \
 303         "sf read 0x80740000 0x740000 0x40000 && "       \
 304         "esbc_validate 0x80700000 && "                  \
 305         "esbc_validate 0x80740000 ;"                    \
 306         "fsl_mc start mc 0x80000000 0x80100000\0"       \
 307         "mcmemsize=0x70000000\0"
 308 #elif defined(CONFIG_SD_BOOT)
 309 #define MC_INIT_CMD                             \
 310         "mcinitcmd=mmcinfo;mmc read 0x80000000 0x5000 0x800;"           \
 311         "mmc read 0x80100000 0x7000 0x800;"                             \
 312         "env exists secureboot && "                     \
 313         "mmc read 0x80700000 0x3800 0x10 && "           \
 314         "mmc read 0x80740000 0x3A00 0x10 && "           \
 315         "esbc_validate 0x80700000 && "                  \
 316         "esbc_validate 0x80740000 ;"                    \
 317         "fsl_mc start mc 0x80000000 0x80100000\0"       \
 318         "mcmemsize=0x70000000\0"
 319 #endif
 320
 321 #undef CONFIG_EXTRA_ENV_SETTINGS
 322 #define CONFIG_EXTRA_ENV_SETTINGS               \
 323         "BOARD=ls1088ardb\0"                    \
 324         "hwconfig=fsl_ddr:bank_intlv=auto\0"    \
 325         "ramdisk_addr=0x800000\0"               \
 326         "ramdisk_size=0x2000000\0"              \
 327         "fdt_high=0xa0000000\0"                 \
 328         "initrd_high=0xffffffffffffffff\0"      \
 329         "fdt_addr=0x64f00000\0"                 \
 330         "kernel_addr=0x1000000\0"               \
 331         "kernel_addr_sd=0x8000\0"               \
 332         "kernelhdr_addr_sd=0x4000\0"            \
 333         "kernel_start=0x580100000\0"            \
 334         "kernelheader_start=0x580800000\0"      \
 335         "scriptaddr=0x80000000\0"               \
 336         "scripthdraddr=0x80080000\0"            \
 337         "fdtheader_addr_r=0x80100000\0"         \
 338         "kernelheader_addr=0x800000\0"          \
 339         "kernelheader_addr_r=0x80200000\0"      \
 340         "kernel_addr_r=0x81000000\0"            \
 341         "kernelheader_size=0x40000\0"           \
 342         "fdt_addr_r=0x90000000\0"               \
 343         "load_addr=0xa0000000\0"                \
 344         "kernel_size=0x2800000\0"               \
 345         "kernel_size_sd=0x14000\0"              \
 346         "kernelhdr_size_sd=0x10\0"              \
 347         MC_INIT_CMD                             \
 348         BOOTENV                                 \
 349         "boot_scripts=ls1088ardb_boot.scr\0"    \
 350         "boot_script_hdr=hdr_ls1088ardb_bs.out\0"       \
 351         "scan_dev_for_boot_part="               \
 352                 "part list ${devtype} ${devnum} devplist; "     \
 353                 "env exists devplist || setenv devplist 1; "    \
 354                 "for distro_bootpart in ${devplist}; do "       \
 355                         "if fstype ${devtype} "                 \
 356                                 "${devnum}:${distro_bootpart} " \
 357                                 "bootfstype; then "             \
 358                                 "run scan_dev_for_boot; "       \
 359                         "fi; "                                  \
 360                 "done\0"                                        \
 361         "scan_dev_for_boot="                                    \
 362                 "echo Scanning ${devtype} "                     \
 363                 "${devnum}:${distro_bootpart}...; "             \
 364                 "for prefix in ${boot_prefixes}; do "           \
 365                         "run scan_dev_for_scripts; "            \
 366                 "done;\0"                                       \
 367         "boot_a_script="                                        \
 368                 "load ${devtype} ${devnum}:${distro_bootpart} " \
 369                 "${scriptaddr} ${prefix}${script}; "            \
 370         "env exists secureboot && load ${devtype} "             \
 371                 "${devnum}:${distro_bootpart} "                 \
 372                 "${scripthdraddr} ${prefix}${boot_script_hdr} " \
 373                 "&& esbc_validate ${scripthdraddr};"            \
 374                 "source ${scriptaddr}\0"                        \
 375         "installer=load mmc 0:2 $load_addr "                    \
 376                 "/flex_installer_arm64.itb; "                   \
 377                 "env exists mcinitcmd && run mcinitcmd && "     \
 378                 "mmc read 0x80001000 0x6800 0x800;"             \
 379                 "fsl_mc lazyapply dpl 0x80001000;"                      \
 380                 "bootm $load_addr#ls1088ardb\0"                 \
 381         "qspi_bootcmd=echo Trying load from qspi..;"            \
 382                 "sf probe && sf read $load_addr "               \
 383                 "$kernel_addr $kernel_size ; env exists secureboot "    \
 384                 "&& sf read $kernelheader_addr_r $kernelheader_addr "   \
 385                 "$kernelheader_size && esbc_validate ${kernelheader_addr_r}; "\
 386                 "bootm $load_addr#$BOARD\0"                     \
 387                 "sd_bootcmd=echo Trying load from sd card..;"           \
 388                 "mmcinfo; mmc read $load_addr "                 \
 389                 "$kernel_addr_sd $kernel_size_sd ;"             \
 390                 "env exists secureboot && mmc read $kernelheader_addr_r "\
 391                 "$kernelhdr_addr_sd $kernelhdr_size_sd "        \
 392                 " && esbc_validate ${kernelheader_addr_r};"     \
 393                 "bootm $load_addr#$BOARD\0"
 394
 395 #undef CONFIG_BOOTCOMMAND
 396 #if defined(CONFIG_QSPI_BOOT)
 397 /* Try to boot an on-QSPI kernel first, then do normal distro boot */
 398 #define CONFIG_BOOTCOMMAND                                      \
 399                 "sf read 0x80001000 0xd00000 0x100000;"         \
 400                 "env exists mcinitcmd && env exists secureboot "        \
 401                 " && sf read 0x80780000 0x780000 0x100000 "     \
 402                 "&& esbc_validate 0x80780000;env exists mcinitcmd "     \
 403                 "&& fsl_mc lazyapply dpl 0x80001000;"           \
 404                 "run distro_bootcmd;run qspi_bootcmd;"          \
 405                 "env exists secureboot && esbc_halt;"
 406
 407 /* Try to boot an on-SD kernel first, then do normal distro boot */
 408 #elif defined(CONFIG_SD_BOOT)
 409 #define CONFIG_BOOTCOMMAND                                      \
 410                 "env exists mcinitcmd && mmcinfo; "             \
 411                 "mmc read 0x80001000 0x6800 0x800; "            \
 412                 "env exists mcinitcmd && env exists secureboot "        \
 413                 " && mmc read 0x80780000 0x3C00 0x10 "          \
 414                 "&& esbc_validate 0x80780000;env exists mcinitcmd "     \
 415                 "&& fsl_mc lazyapply dpl 0x80001000;"           \
 416                 "run distro_bootcmd;run sd_bootcmd;"            \
 417                 "env exists secureboot && esbc_halt;"
 418 #endif
 419
 420 /* MAC/PHY configuration */
 421 #ifdef CONFIG_FSL_MC_ENET
 422 #define CONFIG_PHYLIB
 423
 424 #define CONFIG_PHY_VITESSE
 425 #define AQ_PHY_ADDR1                    0x00
 426 #define AQR105_IRQ_MASK                 0x00000004
 427
 428 #define QSGMII1_PORT1_PHY_ADDR          0x0c
 429 #define QSGMII1_PORT2_PHY_ADDR          0x0d
 430 #define QSGMII1_PORT3_PHY_ADDR          0x0e
 431 #define QSGMII1_PORT4_PHY_ADDR          0x0f
 432 #define QSGMII2_PORT1_PHY_ADDR          0x1c
 433 #define QSGMII2_PORT2_PHY_ADDR          0x1d
 434 #define QSGMII2_PORT3_PHY_ADDR          0x1e
 435 #define QSGMII2_PORT4_PHY_ADDR          0x1f
 436
 437 #define CONFIG_ETHPRIME         "DPMAC1@xgmii"
 438 #define CONFIG_PHY_GIGE
 439 #endif
 440 #endif
 441
 442 /*  MMC  */
 443 #ifdef CONFIG_MMC
 444 #define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
 445 #endif
 446
 447 #ifndef SPL_NO_ENV
 448
 449 #define BOOT_TARGET_DEVICES(func) \
 450         func(MMC, mmc, 0) \
 451         func(SCSI, scsi, 0)
 452 #include <config_distro_bootcmd.h>
 453 #endif
 454
 455 #include <asm/fsl_secure_boot.h>
 456
 457 #endif /* __LS1088A_RDB_H */