include/configs/ls1046a_common.h

   1 /* SPDX-License-Identifier: GPL-2.0+ */
   2 /*
   3  * Copyright 2016 Freescale Semiconductor
   4  * Copyright 2019-2021 NXP
   5  */
   6
   7 #ifndef __LS1046A_COMMON_H
   8 #define __LS1046A_COMMON_H
   9
  10 /* SPL build */
  11 #ifdef CONFIG_SPL_BUILD
  12 #define SPL_NO_QBMAN
  13 #define SPL_NO_FMAN
  14 #define SPL_NO_ENV
  15 #define SPL_NO_MISC
  16 #define SPL_NO_QSPI
  17 #define SPL_NO_USB
  18 #define SPL_NO_SATA
  19 #endif
  20 #if defined(CONFIG_SPL_BUILD) && \
  21         (defined(CONFIG_NAND_BOOT) || defined(CONFIG_QSPI_BOOT))
  22 #define SPL_NO_MMC
  23 #endif
  24 #if defined(CONFIG_SPL_BUILD)           && \
  25         !defined(CONFIG_SPL_FSL_LS_PPA)
  26 #define SPL_NO_IFC
  27 #endif
  28
  29 #include <asm/arch/config.h>
  30 #include <asm/arch/stream_id_lsch2.h>
  31
  32 /* Link Definitions */
  33
  34 #define CONFIG_VERY_BIG_RAM
  35 #define CONFIG_SYS_DDR_SDRAM_BASE       0x80000000
  36 #define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY       0
  37 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE
  38 #define CONFIG_SYS_DDR_BLOCK2_BASE      0x880000000ULL
  39
  40 #define CPU_RELEASE_ADDR               secondary_boot_addr
  41
  42 /* Serial Port */
  43 #define CONFIG_SYS_NS16550_SERIAL
  44 #define CONFIG_SYS_NS16550_REG_SIZE     1
  45 #define CONFIG_SYS_NS16550_CLK          (get_serial_clock())
  46
  47 /* SD boot SPL */
  48 #ifdef CONFIG_SD_BOOT
  49 #define CONFIG_SPL_STACK                0x10020000
  50 #define CONFIG_SPL_BSS_START_ADDR       0x8f000000
  51 #define CONFIG_SYS_SPL_MALLOC_START     (CONFIG_SPL_BSS_START_ADDR + \
  52                                         CONFIG_SPL_BSS_MAX_SIZE)
  53 #define CONFIG_SYS_SPL_MALLOC_SIZE      0x100000
  54
  55 #ifdef CONFIG_NXP_ESBC
  56 #define CONFIG_U_BOOT_HDR_SIZE                          (16 << 10)
  57 /*
  58  * HDR would be appended at end of image and copied to DDR along
  59  * with U-Boot image. Here u-boot max. size is 512K. So if binary
  60  * size increases then increase this size in case of secure boot as
  61  * it uses raw u-boot image instead of fit image.
  62  */
  63 #define CONFIG_SYS_MONITOR_LEN          (0x100000 + CONFIG_U_BOOT_HDR_SIZE)
  64 #else
  65 #define CONFIG_SYS_MONITOR_LEN          0x100000
  66 #endif /* ifdef CONFIG_NXP_ESBC */
  67 #endif
  68
  69 #if defined(CONFIG_QSPI_BOOT) && defined(CONFIG_SPL)
  70 #define CONFIG_SPL_TARGET               "spl/u-boot-spl.pbl"
  71 #define CONFIG_SPL_STACK                0x10020000
  72 #define CONFIG_SPL_BSS_START_ADDR       0x8f000000
  73 #define CONFIG_SYS_SPL_MALLOC_START     (CONFIG_SPL_BSS_START_ADDR + \
  74                                         CONFIG_SPL_BSS_MAX_SIZE)
  75 #define CONFIG_SYS_SPL_MALLOC_SIZE      0x100000
  76 #define CONFIG_SYS_MONITOR_LEN          0x100000
  77 #endif
  78
  79 /* NAND SPL */
  80 #ifdef CONFIG_NAND_BOOT
  81 #define CONFIG_SPL_STACK                0x1001f000
  82 #define CONFIG_SYS_NAND_U_BOOT_DST      CONFIG_SYS_TEXT_BASE
  83 #define CONFIG_SYS_NAND_U_BOOT_START    CONFIG_SYS_TEXT_BASE
  84
  85 #define CONFIG_SPL_BSS_START_ADDR       0x8f000000
  86 #define CONFIG_SYS_SPL_MALLOC_START     (CONFIG_SPL_BSS_START_ADDR + \
  87                                         CONFIG_SPL_BSS_MAX_SIZE)
  88 #define CONFIG_SYS_SPL_MALLOC_SIZE      0x100000
  89 #define CONFIG_SYS_MONITOR_LEN          0xa0000
  90 #endif
  91
  92 /* GPIO */
  93
  94 /* I2C */
  95
  96 /* PCIe */
  97 #define CONFIG_PCIE1            /* PCIE controller 1 */
  98 #define CONFIG_PCIE2            /* PCIE controller 2 */
  99 #define CONFIG_PCIE3            /* PCIE controller 3 */
 100
 101 #ifdef CONFIG_PCI
 102 #define CONFIG_PCI_SCAN_SHOW
 103 #endif
 104
 105 /* SATA */
 106 #ifndef SPL_NO_SATA
 107 #define CONFIG_SYS_SATA                         AHCI_BASE_ADDR
 108 #endif
 109
 110 /* FMan ucode */
 111 #ifndef SPL_NO_FMAN
 112 #define CONFIG_SYS_DPAA_FMAN
 113 #ifdef CONFIG_SYS_DPAA_FMAN
 114 #define CONFIG_SYS_FM_MURAM_SIZE        0x60000
 115 #endif
 116 #define CONFIG_SYS_FDT_PAD              (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
 117 #endif
 118
 119 /* Miscellaneous configurable options */
 120
 121 #define CONFIG_HWCONFIG
 122 #define HWCONFIG_BUFFER_SIZE            128
 123
 124 #ifndef CONFIG_SPL_BUILD
 125 #define BOOT_TARGET_DEVICES(func) \
 126         func(SCSI, scsi, 0) \
 127         func(MMC, mmc, 0) \
 128         func(USB, usb, 0) \
 129         func(DHCP, dhcp, na)
 130 #include <config_distro_bootcmd.h>
 131 #endif
 132
 133 #if defined(CONFIG_TARGET_LS1046AFRWY)
 134 #define LS1046A_BOOT_SRC_AND_HDR\
 135         "boot_scripts=ls1046afrwy_boot.scr\0"   \
 136         "boot_script_hdr=hdr_ls1046afrwy_bs.out\0"
 137 #elif defined(CONFIG_TARGET_LS1046AQDS)
 138 #define LS1046A_BOOT_SRC_AND_HDR\
 139         "boot_scripts=ls1046aqds_boot.scr\0"    \
 140         "boot_script_hdr=hdr_ls1046aqds_bs.out\0"
 141 #else
 142 #define LS1046A_BOOT_SRC_AND_HDR\
 143         "boot_scripts=ls1046ardb_boot.scr\0"    \
 144         "boot_script_hdr=hdr_ls1046ardb_bs.out\0"
 145 #endif
 146 #ifndef SPL_NO_MISC
 147 /* Initial environment variables */
 148 #define CONFIG_EXTRA_ENV_SETTINGS               \
 149         "hwconfig=fsl_ddr:bank_intlv=auto\0"    \
 150         "ramdisk_addr=0x800000\0"               \
 151         "ramdisk_size=0x2000000\0"              \
 152         "bootm_size=0x10000000\0"               \
 153         "kernel_addr=0x61000000\0"              \
 154         "scriptaddr=0x80000000\0"               \
 155         "scripthdraddr=0x80080000\0"            \
 156         "fdtheader_addr_r=0x80100000\0"         \
 157         "kernelheader_addr_r=0x80200000\0"      \
 158         "load_addr=0xa0000000\0"            \
 159         "kernel_addr_r=0x81000000\0"            \
 160         "fdt_addr_r=0x90000000\0"               \
 161         "ramdisk_addr_r=0xa0000000\0"           \
 162         "kernel_start=0x1000000\0"              \
 163         "kernelheader_start=0x600000\0"         \
 164         "kernel_load=0xa0000000\0"              \
 165         "kernel_size=0x2800000\0"               \
 166         "kernelheader_size=0x40000\0"           \
 167         "kernel_addr_sd=0x8000\0"               \
 168         "kernel_size_sd=0x14000\0"              \
 169         "kernelhdr_addr_sd=0x3000\0"            \
 170         "kernelhdr_size_sd=0x10\0"              \
 171         "console=ttyS0,115200\0"                \
 172          CONFIG_MTDPARTS_DEFAULT "\0"           \
 173         BOOTENV                                 \
 174         LS1046A_BOOT_SRC_AND_HDR                \
 175         "scan_dev_for_boot_part="               \
 176                 "part list ${devtype} ${devnum} devplist; "   \
 177                 "env exists devplist || setenv devplist 1; "  \
 178                 "for distro_bootpart in ${devplist}; do "     \
 179                   "if fstype ${devtype} "                  \
 180                         "${devnum}:${distro_bootpart} "      \
 181                         "bootfstype; then "                  \
 182                         "run scan_dev_for_boot; "            \
 183                   "fi; "                                   \
 184                 "done\0"                                   \
 185         "boot_a_script="                                  \
 186                 "load ${devtype} ${devnum}:${distro_bootpart} "  \
 187                         "${scriptaddr} ${prefix}${script}; "    \
 188                 "env exists secureboot && load ${devtype} "     \
 189                         "${devnum}:${distro_bootpart} "         \
 190                         "${scripthdraddr} ${prefix}${boot_script_hdr}; " \
 191                         "env exists secureboot "        \
 192                         "&& esbc_validate ${scripthdraddr};"    \
 193                 "source ${scriptaddr}\0"          \
 194         "qspi_bootcmd=echo Trying load from qspi..;"      \
 195                 "sf probe && sf read $load_addr "         \
 196                 "$kernel_start $kernel_size; env exists secureboot "    \
 197                 "&& sf read $kernelheader_addr_r $kernelheader_start "  \
 198                 "$kernelheader_size && esbc_validate ${kernelheader_addr_r}; " \
 199                 "bootm $load_addr#$board\0"             \
 200         "nand_bootcmd=echo Trying load from nand..;"      \
 201                 "nand info; nand read $load_addr "         \
 202                 "$kernel_start $kernel_size; env exists secureboot "    \
 203                 "&& nand read $kernelheader_addr_r $kernelheader_start " \
 204                 "$kernelheader_size && esbc_validate ${kernelheader_addr_r}; " \
 205                 "bootm $load_addr#$board\0"             \
 206         "nor_bootcmd=echo Trying load from nor..;"      \
 207                 "cp.b $kernel_addr $load_addr "         \
 208                 "$kernel_size; env exists secureboot "  \
 209                 "&& cp.b $kernelheader_addr $kernelheader_addr_r "      \
 210                 "$kernelheader_size && esbc_validate ${kernelheader_addr_r}; " \
 211                 "bootm $load_addr#$board\0"     \
 212         "sd_bootcmd=echo Trying load from SD ..;"       \
 213                 "mmcinfo; mmc read $load_addr "         \
 214                 "$kernel_addr_sd $kernel_size_sd && "   \
 215                 "env exists secureboot && mmc read $kernelheader_addr_r "               \
 216                 "$kernelhdr_addr_sd $kernelhdr_size_sd "                \
 217                 " && esbc_validate ${kernelheader_addr_r};"     \
 218                 "bootm $load_addr#$board\0"
 219
 220 #endif
 221
 222 #define CONFIG_SYS_BOOTM_LEN   (64 << 20)      /* Increase max gunzip size */
 223
 224 #include <asm/arch/soc.h>
 225
 226 #endif /* __LS1046A_COMMON_H */