include/configs/ls1043aqds.h

   1 /*
   2  * Copyright 2015 Freescale Semiconductor, Inc.
   3  *
   4  * SPDX-License-Identifier:     GPL-2.0+
   5  */
   6
   7 #ifndef __LS1043AQDS_H__
   8 #define __LS1043AQDS_H__
   9
  10 #include "ls1043a_common.h"
  11
  12 #if defined(CONFIG_NAND_BOOT) || defined(CONFIG_SD_BOOT)
  13 #define CONFIG_SYS_TEXT_BASE            0x82000000
  14 #elif defined(CONFIG_QSPI_BOOT)
  15 #define CONFIG_SYS_TEXT_BASE            0x40010000
  16 #else
  17 #define CONFIG_SYS_TEXT_BASE            0x60100000
  18 #endif
  19
  20 #ifndef __ASSEMBLY__
  21 unsigned long get_board_sys_clk(void);
  22 unsigned long get_board_ddr_clk(void);
  23 #endif
  24
  25 #define CONFIG_SYS_CLK_FREQ             get_board_sys_clk()
  26 #define CONFIG_DDR_CLK_FREQ             get_board_ddr_clk()
  27
  28 #define CONFIG_SKIP_LOWLEVEL_INIT
  29
  30 #define CONFIG_LAYERSCAPE_NS_ACCESS
  31
  32 #define CONFIG_DIMM_SLOTS_PER_CTLR      1
  33 /* Physical Memory Map */
  34 #define CONFIG_CHIP_SELECTS_PER_CTRL    4
  35 #define CONFIG_NR_DRAM_BANKS            2
  36
  37 #define CONFIG_DDR_SPD
  38 #define SPD_EEPROM_ADDRESS              0x51
  39 #define CONFIG_SYS_SPD_BUS_NUM          0
  40
  41 #define CONFIG_FSL_DDR_INTERACTIVE      /* Interactive debugging */
  42
  43 #define CONFIG_DDR_ECC
  44 #ifdef CONFIG_DDR_ECC
  45 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
  46 #define CONFIG_MEM_INIT_VALUE           0xdeadbeef
  47 #endif
  48
  49 #ifdef CONFIG_SYS_DPAA_FMAN
  50 #define CONFIG_FMAN_ENET
  51 #define CONFIG_PHYLIB
  52 #define CONFIG_PHY_VITESSE
  53 #define CONFIG_PHY_REALTEK
  54 #define CONFIG_PHYLIB_10G
  55 #define RGMII_PHY1_ADDR         0x1
  56 #define RGMII_PHY2_ADDR         0x2
  57 #define SGMII_CARD_PORT1_PHY_ADDR 0x1C
  58 #define SGMII_CARD_PORT2_PHY_ADDR 0x1D
  59 #define SGMII_CARD_PORT3_PHY_ADDR 0x1E
  60 #define SGMII_CARD_PORT4_PHY_ADDR 0x1F
  61 /* PHY address on QSGMII riser card on slot 1 */
  62 #define QSGMII_CARD_PORT1_PHY_ADDR_S1 0x4
  63 #define QSGMII_CARD_PORT2_PHY_ADDR_S1 0x5
  64 #define QSGMII_CARD_PORT3_PHY_ADDR_S1 0x6
  65 #define QSGMII_CARD_PORT4_PHY_ADDR_S1 0x7
  66 /* PHY address on QSGMII riser card on slot 2 */
  67 #define QSGMII_CARD_PORT1_PHY_ADDR_S2 0x8
  68 #define QSGMII_CARD_PORT2_PHY_ADDR_S2 0x9
  69 #define QSGMII_CARD_PORT3_PHY_ADDR_S2 0xA
  70 #define QSGMII_CARD_PORT4_PHY_ADDR_S2 0xB
  71 #endif
  72
  73 #ifdef CONFIG_RAMBOOT_PBL
  74 #define CONFIG_SYS_FSL_PBL_PBI board/freescale/ls1043aqds/ls1043aqds_pbi.cfg
  75 #endif
  76
  77 #ifdef CONFIG_NAND_BOOT
  78 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/ls1043aqds/ls1043aqds_rcw_nand.cfg
  79 #endif
  80
  81 #ifdef CONFIG_SD_BOOT
  82 #ifdef CONFIG_SD_BOOT_QSPI
  83 #define CONFIG_SYS_FSL_PBL_RCW \
  84         board/freescale/ls1043aqds/ls1043aqds_rcw_sd_qspi.cfg
  85 #else
  86 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/ls1043aqds/ls1043aqds_rcw_sd_ifc.cfg
  87 #endif
  88 #endif
  89
  90 /* LPUART */
  91 #ifdef CONFIG_LPUART
  92 #define CONFIG_LPUART_32B_REG
  93 #endif
  94
  95 /* SATA */
  96 #define CONFIG_LIBATA
  97 #define CONFIG_SCSI_AHCI
  98 #define CONFIG_SCSI_AHCI_PLAT
  99 #define CONFIG_SCSI
 100 #define CONFIG_DOS_PARTITION
 101 #define CONFIG_BOARD_LATE_INIT
 102
 103 #define CONFIG_PARTITION_UUIDS
 104 #define CONFIG_EFI_PARTITION
 105 #define CONFIG_CMD_GPT
 106
 107 /* EEPROM */
 108 #define CONFIG_ID_EEPROM
 109 #define CONFIG_SYS_I2C_EEPROM_NXID
 110 #define CONFIG_SYS_EEPROM_BUS_NUM               0
 111 #define CONFIG_SYS_I2C_EEPROM_ADDR              0x57
 112 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN          1
 113 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS       3
 114 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS   5
 115
 116 #define CONFIG_SYS_SATA                         AHCI_BASE_ADDR
 117
 118 #define CONFIG_SYS_SCSI_MAX_SCSI_ID             1
 119 #define CONFIG_SYS_SCSI_MAX_LUN                 1
 120 #define CONFIG_SYS_SCSI_MAX_DEVICE              (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
 121                                                 CONFIG_SYS_SCSI_MAX_LUN)
 122
 123 /*
 124  * IFC Definitions
 125  */
 126 #if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
 127 #define CONFIG_SYS_NOR0_CSPR_EXT        (0x0)
 128 #define CONFIG_SYS_NOR0_CSPR    (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
 129                                 CSPR_PORT_SIZE_16 | \
 130                                 CSPR_MSEL_NOR | \
 131                                 CSPR_V)
 132 #define CONFIG_SYS_NOR1_CSPR_EXT        (0x0)
 133 #define CONFIG_SYS_NOR1_CSPR    (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS \
 134                                 + 0x8000000) | \
 135                                 CSPR_PORT_SIZE_16 | \
 136                                 CSPR_MSEL_NOR | \
 137                                 CSPR_V)
 138 #define CONFIG_SYS_NOR_AMASK            IFC_AMASK(128 * 1024 * 1024)
 139
 140 #define CONFIG_SYS_NOR_CSOR             (CSOR_NOR_ADM_SHIFT(4) | \
 141                                         CSOR_NOR_TRHZ_80)
 142 #define CONFIG_SYS_NOR_FTIM0            (FTIM0_NOR_TACSE(0x4) | \
 143                                         FTIM0_NOR_TEADC(0x5) | \
 144                                         FTIM0_NOR_TEAHC(0x5))
 145 #define CONFIG_SYS_NOR_FTIM1            (FTIM1_NOR_TACO(0x35) | \
 146                                         FTIM1_NOR_TRAD_NOR(0x1a) | \
 147                                         FTIM1_NOR_TSEQRAD_NOR(0x13))
 148 #define CONFIG_SYS_NOR_FTIM2            (FTIM2_NOR_TCS(0x4) | \
 149                                         FTIM2_NOR_TCH(0x4) | \
 150                                         FTIM2_NOR_TWPH(0xe) | \
 151                                         FTIM2_NOR_TWP(0x1c))
 152 #define CONFIG_SYS_NOR_FTIM3            0
 153
 154 #define CONFIG_SYS_MAX_FLASH_BANKS      1       /* number of banks */
 155 #define CONFIG_SYS_MAX_FLASH_SECT       1024    /* sectors per device */
 156 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000   /* Flash Erase Timeout (ms) */
 157 #define CONFIG_SYS_FLASH_WRITE_TOUT     500     /* Flash Write Timeout (ms) */
 158
 159 #define CONFIG_SYS_FLASH_EMPTY_INFO
 160 #define CONFIG_SYS_FLASH_BANKS_LIST     {CONFIG_SYS_FLASH_BASE_PHYS, \
 161                                         CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000}
 162
 163 #define CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS
 164 #define CONFIG_SYS_WRITE_SWAPPED_DATA
 165
 166 /*
 167  * NAND Flash Definitions
 168  */
 169 #define CONFIG_NAND_FSL_IFC
 170
 171 #define CONFIG_SYS_NAND_BASE            0x7e800000
 172 #define CONFIG_SYS_NAND_BASE_PHYS       CONFIG_SYS_NAND_BASE
 173
 174 #define CONFIG_SYS_NAND_CSPR_EXT        (0x0)
 175
 176 #define CONFIG_SYS_NAND_CSPR    (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
 177                                 | CSPR_PORT_SIZE_8      \
 178                                 | CSPR_MSEL_NAND        \
 179                                 | CSPR_V)
 180 #define CONFIG_SYS_NAND_AMASK   IFC_AMASK(64*1024)
 181 #define CONFIG_SYS_NAND_CSOR    (CSOR_NAND_ECC_ENC_EN   /* ECC on encode */ \
 182                                 | CSOR_NAND_ECC_DEC_EN  /* ECC on decode */ \
 183                                 | CSOR_NAND_ECC_MODE_4  /* 4-bit ECC */ \
 184                                 | CSOR_NAND_RAL_3       /* RAL = 3 Bytes */ \
 185                                 | CSOR_NAND_PGS_2K      /* Page Size = 2K */ \
 186                                 | CSOR_NAND_SPRZ_64     /* Spare size = 64 */ \
 187                                 | CSOR_NAND_PB(64))     /* 64 Pages Per Block */
 188
 189 #define CONFIG_SYS_NAND_ONFI_DETECTION
 190
 191 #define CONFIG_SYS_NAND_FTIM0           (FTIM0_NAND_TCCST(0x7) | \
 192                                         FTIM0_NAND_TWP(0x18)   | \
 193                                         FTIM0_NAND_TWCHT(0x7) | \
 194                                         FTIM0_NAND_TWH(0xa))
 195 #define CONFIG_SYS_NAND_FTIM1           (FTIM1_NAND_TADLE(0x32) | \
 196                                         FTIM1_NAND_TWBE(0x39)  | \
 197                                         FTIM1_NAND_TRR(0xe)   | \
 198                                         FTIM1_NAND_TRP(0x18))
 199 #define CONFIG_SYS_NAND_FTIM2           (FTIM2_NAND_TRAD(0xf) | \
 200                                         FTIM2_NAND_TREH(0xa) | \
 201                                         FTIM2_NAND_TWHRE(0x1e))
 202 #define CONFIG_SYS_NAND_FTIM3           0x0
 203
 204 #define CONFIG_SYS_NAND_BASE_LIST       { CONFIG_SYS_NAND_BASE }
 205 #define CONFIG_SYS_MAX_NAND_DEVICE      1
 206 #define CONFIG_MTD_NAND_VERIFY_WRITE
 207 #define CONFIG_CMD_NAND
 208
 209 #define CONFIG_SYS_NAND_BLOCK_SIZE      (128 * 1024)
 210 #endif
 211
 212 #ifdef CONFIG_NAND_BOOT
 213 #define CONFIG_SPL_PAD_TO               0x20000         /* block aligned */
 214 #define CONFIG_SYS_NAND_U_BOOT_OFFS     CONFIG_SPL_PAD_TO
 215 #define CONFIG_SYS_NAND_U_BOOT_SIZE     (640 << 10)
 216 #endif
 217
 218 #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
 219 #define CONFIG_QIXIS_I2C_ACCESS
 220 #define CONFIG_SYS_I2C_EARLY_INIT
 221 #define CONFIG_SYS_NO_FLASH
 222 #endif
 223
 224 /*
 225  * QIXIS Definitions
 226  */
 227 #define CONFIG_FSL_QIXIS
 228
 229 #ifdef CONFIG_FSL_QIXIS
 230 #define QIXIS_BASE                      0x7fb00000
 231 #define QIXIS_BASE_PHYS                 QIXIS_BASE
 232 #define CONFIG_SYS_I2C_FPGA_ADDR        0x66
 233 #define QIXIS_LBMAP_SWITCH              6
 234 #define QIXIS_LBMAP_MASK                0x0f
 235 #define QIXIS_LBMAP_SHIFT               0
 236 #define QIXIS_LBMAP_DFLTBANK            0x00
 237 #define QIXIS_LBMAP_ALTBANK             0x04
 238 #define QIXIS_LBMAP_NAND                0x09
 239 #define QIXIS_LBMAP_SD                  0x00
 240 #define QIXIS_LBMAP_SD_QSPI             0xff
 241 #define QIXIS_LBMAP_QSPI                0xff
 242 #define QIXIS_RCW_SRC_NAND              0x106
 243 #define QIXIS_RCW_SRC_SD                0x040
 244 #define QIXIS_RCW_SRC_QSPI              0x045
 245 #define QIXIS_RST_CTL_RESET             0x41
 246 #define QIXIS_RCFG_CTL_RECONFIG_IDLE    0x20
 247 #define QIXIS_RCFG_CTL_RECONFIG_START   0x21
 248 #define QIXIS_RCFG_CTL_WATCHDOG_ENBLE   0x08
 249
 250 #define CONFIG_SYS_FPGA_CSPR_EXT        (0x0)
 251 #define CONFIG_SYS_FPGA_CSPR            (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) | \
 252                                         CSPR_PORT_SIZE_8 | \
 253                                         CSPR_MSEL_GPCM | \
 254                                         CSPR_V)
 255 #define CONFIG_SYS_FPGA_AMASK           IFC_AMASK(64 * 1024)
 256 #define CONFIG_SYS_FPGA_CSOR            (CSOR_NOR_ADM_SHIFT(4) | \
 257                                         CSOR_NOR_NOR_MODE_AVD_NOR | \
 258                                         CSOR_NOR_TRHZ_80)
 259
 260 /*
 261  * QIXIS Timing parameters for IFC GPCM
 262  */
 263 #define CONFIG_SYS_FPGA_FTIM0           (FTIM0_GPCM_TACSE(0xc) | \
 264                                         FTIM0_GPCM_TEADC(0x20) | \
 265                                         FTIM0_GPCM_TEAHC(0x10))
 266 #define CONFIG_SYS_FPGA_FTIM1           (FTIM1_GPCM_TACO(0x50) | \
 267                                         FTIM1_GPCM_TRAD(0x1f))
 268 #define CONFIG_SYS_FPGA_FTIM2           (FTIM2_GPCM_TCS(0x8) | \
 269                                         FTIM2_GPCM_TCH(0x8) | \
 270                                         FTIM2_GPCM_TWP(0xf0))
 271 #define CONFIG_SYS_FPGA_FTIM3           0x0
 272 #endif
 273
 274 #ifdef CONFIG_NAND_BOOT
 275 #define CONFIG_SYS_CSPR0_EXT            CONFIG_SYS_NAND_CSPR_EXT
 276 #define CONFIG_SYS_CSPR0                CONFIG_SYS_NAND_CSPR
 277 #define CONFIG_SYS_AMASK0               CONFIG_SYS_NAND_AMASK
 278 #define CONFIG_SYS_CSOR0                CONFIG_SYS_NAND_CSOR
 279 #define CONFIG_SYS_CS0_FTIM0            CONFIG_SYS_NAND_FTIM0
 280 #define CONFIG_SYS_CS0_FTIM1            CONFIG_SYS_NAND_FTIM1
 281 #define CONFIG_SYS_CS0_FTIM2            CONFIG_SYS_NAND_FTIM2
 282 #define CONFIG_SYS_CS0_FTIM3            CONFIG_SYS_NAND_FTIM3
 283 #define CONFIG_SYS_CSPR1_EXT            CONFIG_SYS_NOR0_CSPR_EXT
 284 #define CONFIG_SYS_CSPR1                CONFIG_SYS_NOR0_CSPR
 285 #define CONFIG_SYS_AMASK1               CONFIG_SYS_NOR_AMASK
 286 #define CONFIG_SYS_CSOR1                CONFIG_SYS_NOR_CSOR
 287 #define CONFIG_SYS_CS1_FTIM0            CONFIG_SYS_NOR_FTIM0
 288 #define CONFIG_SYS_CS1_FTIM1            CONFIG_SYS_NOR_FTIM1
 289 #define CONFIG_SYS_CS1_FTIM2            CONFIG_SYS_NOR_FTIM2
 290 #define CONFIG_SYS_CS1_FTIM3            CONFIG_SYS_NOR_FTIM3
 291 #define CONFIG_SYS_CSPR2_EXT            CONFIG_SYS_NOR1_CSPR_EXT
 292 #define CONFIG_SYS_CSPR2                CONFIG_SYS_NOR1_CSPR
 293 #define CONFIG_SYS_AMASK2               CONFIG_SYS_NOR_AMASK
 294 #define CONFIG_SYS_CSOR2                CONFIG_SYS_NOR_CSOR
 295 #define CONFIG_SYS_CS2_FTIM0            CONFIG_SYS_NOR_FTIM0
 296 #define CONFIG_SYS_CS2_FTIM1            CONFIG_SYS_NOR_FTIM1
 297 #define CONFIG_SYS_CS2_FTIM2            CONFIG_SYS_NOR_FTIM2
 298 #define CONFIG_SYS_CS2_FTIM3            CONFIG_SYS_NOR_FTIM3
 299 #define CONFIG_SYS_CSPR3_EXT            CONFIG_SYS_FPGA_CSPR_EXT
 300 #define CONFIG_SYS_CSPR3                CONFIG_SYS_FPGA_CSPR
 301 #define CONFIG_SYS_AMASK3               CONFIG_SYS_FPGA_AMASK
 302 #define CONFIG_SYS_CSOR3                CONFIG_SYS_FPGA_CSOR
 303 #define CONFIG_SYS_CS3_FTIM0            CONFIG_SYS_FPGA_FTIM0
 304 #define CONFIG_SYS_CS3_FTIM1            CONFIG_SYS_FPGA_FTIM1
 305 #define CONFIG_SYS_CS3_FTIM2            CONFIG_SYS_FPGA_FTIM2
 306 #define CONFIG_SYS_CS3_FTIM3            CONFIG_SYS_FPGA_FTIM3
 307 #else
 308 #define CONFIG_SYS_CSPR0_EXT            CONFIG_SYS_NOR0_CSPR_EXT
 309 #define CONFIG_SYS_CSPR0                CONFIG_SYS_NOR0_CSPR
 310 #define CONFIG_SYS_AMASK0               CONFIG_SYS_NOR_AMASK
 311 #define CONFIG_SYS_CSOR0                CONFIG_SYS_NOR_CSOR
 312 #define CONFIG_SYS_CS0_FTIM0            CONFIG_SYS_NOR_FTIM0
 313 #define CONFIG_SYS_CS0_FTIM1            CONFIG_SYS_NOR_FTIM1
 314 #define CONFIG_SYS_CS0_FTIM2            CONFIG_SYS_NOR_FTIM2
 315 #define CONFIG_SYS_CS0_FTIM3            CONFIG_SYS_NOR_FTIM3
 316 #define CONFIG_SYS_CSPR1_EXT            CONFIG_SYS_NOR1_CSPR_EXT
 317 #define CONFIG_SYS_CSPR1                CONFIG_SYS_NOR1_CSPR
 318 #define CONFIG_SYS_AMASK1               CONFIG_SYS_NOR_AMASK
 319 #define CONFIG_SYS_CSOR1                CONFIG_SYS_NOR_CSOR
 320 #define CONFIG_SYS_CS1_FTIM0            CONFIG_SYS_NOR_FTIM0
 321 #define CONFIG_SYS_CS1_FTIM1            CONFIG_SYS_NOR_FTIM1
 322 #define CONFIG_SYS_CS1_FTIM2            CONFIG_SYS_NOR_FTIM2
 323 #define CONFIG_SYS_CS1_FTIM3            CONFIG_SYS_NOR_FTIM3
 324 #define CONFIG_SYS_CSPR2_EXT            CONFIG_SYS_NAND_CSPR_EXT
 325 #define CONFIG_SYS_CSPR2                CONFIG_SYS_NAND_CSPR
 326 #define CONFIG_SYS_AMASK2               CONFIG_SYS_NAND_AMASK
 327 #define CONFIG_SYS_CSOR2                CONFIG_SYS_NAND_CSOR
 328 #define CONFIG_SYS_CS2_FTIM0            CONFIG_SYS_NAND_FTIM0
 329 #define CONFIG_SYS_CS2_FTIM1            CONFIG_SYS_NAND_FTIM1
 330 #define CONFIG_SYS_CS2_FTIM2            CONFIG_SYS_NAND_FTIM2
 331 #define CONFIG_SYS_CS2_FTIM3            CONFIG_SYS_NAND_FTIM3
 332 #define CONFIG_SYS_CSPR3_EXT            CONFIG_SYS_FPGA_CSPR_EXT
 333 #define CONFIG_SYS_CSPR3                CONFIG_SYS_FPGA_CSPR
 334 #define CONFIG_SYS_AMASK3               CONFIG_SYS_FPGA_AMASK
 335 #define CONFIG_SYS_CSOR3                CONFIG_SYS_FPGA_CSOR
 336 #define CONFIG_SYS_CS3_FTIM0            CONFIG_SYS_FPGA_FTIM0
 337 #define CONFIG_SYS_CS3_FTIM1            CONFIG_SYS_FPGA_FTIM1
 338 #define CONFIG_SYS_CS3_FTIM2            CONFIG_SYS_FPGA_FTIM2
 339 #define CONFIG_SYS_CS3_FTIM3            CONFIG_SYS_FPGA_FTIM3
 340 #endif
 341
 342 /*
 343  * I2C bus multiplexer
 344  */
 345 #define I2C_MUX_PCA_ADDR_PRI            0x77
 346 #define I2C_MUX_PCA_ADDR_SEC            0x76 /* Secondary multiplexer */
 347 #define I2C_RETIMER_ADDR                0x18
 348 #define I2C_MUX_CH_DEFAULT              0x8
 349 #define I2C_MUX_CH_CH7301               0xC
 350 #define I2C_MUX_CH5                     0xD
 351 #define I2C_MUX_CH7                     0xF
 352
 353 #define I2C_MUX_CH_VOL_MONITOR 0xa
 354
 355 /* Voltage monitor on channel 2*/
 356 #define I2C_VOL_MONITOR_ADDR           0x40
 357 #define I2C_VOL_MONITOR_BUS_V_OFFSET   0x2
 358 #define I2C_VOL_MONITOR_BUS_V_OVF      0x1
 359 #define I2C_VOL_MONITOR_BUS_V_SHIFT    3
 360
 361 #define CONFIG_VID_FLS_ENV              "ls1043aqds_vdd_mv"
 362 #ifndef CONFIG_SPL_BUILD
 363 #define CONFIG_VID
 364 #endif
 365 #define CONFIG_VOL_MONITOR_IR36021_SET
 366 #define CONFIG_VOL_MONITOR_INA220
 367 /* The lowest and highest voltage allowed for LS1043AQDS */
 368 #define VDD_MV_MIN                      819
 369 #define VDD_MV_MAX                      1212
 370
 371 /* QSPI device */
 372 #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
 373 #define CONFIG_FSL_QSPI
 374 #ifdef CONFIG_FSL_QSPI
 375 #define CONFIG_SPI_FLASH_SPANSION
 376 #define FSL_QSPI_FLASH_SIZE             (1 << 24)
 377 #define FSL_QSPI_FLASH_NUM              2
 378 #endif
 379 #endif
 380
 381 /* USB */
 382 #define CONFIG_HAS_FSL_XHCI_USB
 383 #ifdef CONFIG_HAS_FSL_XHCI_USB
 384 #define CONFIG_USB_XHCI_FSL
 385 #define CONFIG_USB_MAX_CONTROLLER_COUNT         3
 386 #define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS      2
 387 #endif
 388
 389 /*
 390  * Miscellaneous configurable options
 391  */
 392 #define CONFIG_MISC_INIT_R
 393 #define CONFIG_SYS_LONGHELP             /* undef to save memory */
 394 #define CONFIG_AUTO_COMPLETE
 395 #define CONFIG_SYS_PBSIZE               \
 396                 (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
 397 #define CONFIG_SYS_BARGSIZE             CONFIG_SYS_CBSIZE
 398
 399 #define CONFIG_SYS_MEMTEST_START        0x80000000
 400 #define CONFIG_SYS_MEMTEST_END          0x9fffffff
 401
 402 #define CONFIG_SYS_HZ                   1000
 403
 404 /*
 405  * Stack sizes
 406  * The stack sizes are set up in start.S using the settings below
 407  */
 408 #define CONFIG_STACKSIZE                (30 * 1024)
 409
 410 #define CONFIG_SYS_INIT_SP_OFFSET \
 411         (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 412
 413 #ifdef CONFIG_SPL_BUILD
 414 #define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE
 415 #else
 416 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE    /* start of monitor */
 417 #endif
 418
 419 /*
 420  * Environment
 421  */
 422 #define CONFIG_ENV_OVERWRITE
 423
 424 #ifdef CONFIG_NAND_BOOT
 425 #define CONFIG_ENV_IS_IN_NAND
 426 #define CONFIG_ENV_SIZE                 0x2000
 427 #define CONFIG_ENV_OFFSET               (10 * CONFIG_SYS_NAND_BLOCK_SIZE)
 428 #elif defined(CONFIG_SD_BOOT)
 429 #define CONFIG_ENV_OFFSET               (1024 * 1024)
 430 #define CONFIG_ENV_IS_IN_MMC
 431 #define CONFIG_SYS_MMC_ENV_DEV          0
 432 #define CONFIG_ENV_SIZE                 0x2000
 433 #elif defined(CONFIG_QSPI_BOOT)
 434 #define CONFIG_ENV_IS_IN_SPI_FLASH
 435 #define CONFIG_ENV_SIZE                 0x2000          /* 8KB */
 436 #define CONFIG_ENV_OFFSET               0x100000        /* 1MB */
 437 #define CONFIG_ENV_SECT_SIZE            0x10000
 438 #else
 439 #define CONFIG_ENV_IS_IN_FLASH
 440 #define CONFIG_ENV_ADDR                 (CONFIG_SYS_FLASH_BASE + 0x200000)
 441 #define CONFIG_ENV_SECT_SIZE            0x20000
 442 #define CONFIG_ENV_SIZE                 0x20000
 443 #endif
 444
 445 #define CONFIG_CMDLINE_TAG
 446
 447 #include <asm/fsl_secure_boot.h>
 448
 449 #endif /* __LS1043AQDS_H__ */