include/configs/ls1043a_common.h

   1 /*
   2  * Copyright (C) 2015 Freescale Semiconductor
   3  *
   4  * SPDX-License-Identifier:     GPL-2.0+
   5  */
   6
   7 #ifndef __LS1043A_COMMON_H
   8 #define __LS1043A_COMMON_H
   9
  10 /* SPL build */
  11 #ifdef CONFIG_SPL_BUILD
  12 #define SPL_NO_FMAN
  13 #define SPL_NO_DSPI
  14 #define SPL_NO_PCIE
  15 #define SPL_NO_ENV
  16 #define SPL_NO_MISC
  17 #define SPL_NO_USB
  18 #define SPL_NO_SATA
  19 #define SPL_NO_QE
  20 #define SPL_NO_EEPROM
  21 #endif
  22 #if (defined(CONFIG_SPL_BUILD) && defined(CONFIG_NAND_BOOT))
  23 #define SPL_NO_MMC
  24 #endif
  25 #if (defined(CONFIG_SPL_BUILD) && defined(CONFIG_SD_BOOT_QSPI))
  26 #define SPL_NO_IFC
  27 #endif
  28
  29 #define CONFIG_REMAKE_ELF
  30 #define CONFIG_FSL_LAYERSCAPE
  31 #define CONFIG_MP
  32 #define CONFIG_GICV2
  33
  34 #include <asm/arch/stream_id_lsch2.h>
  35 #include <asm/arch/config.h>
  36
  37 /* Link Definitions */
  38 #define CONFIG_SYS_INIT_SP_ADDR         (CONFIG_SYS_FSL_OCRAM_BASE + 0xfff0)
  39
  40 #define CONFIG_SUPPORT_RAW_INITRD
  41
  42 #define CONFIG_SKIP_LOWLEVEL_INIT
  43
  44 #define CONFIG_VERY_BIG_RAM
  45 #define CONFIG_SYS_DDR_SDRAM_BASE       0x80000000
  46 #define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY       0
  47 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE
  48 #define CONFIG_SYS_DDR_BLOCK2_BASE      0x880000000ULL
  49
  50 #define CPU_RELEASE_ADDR               secondary_boot_func
  51
  52 /* Generic Timer Definitions */
  53 #define COUNTER_FREQUENCY               25000000        /* 25MHz */
  54
  55 /* Size of malloc() pool */
  56 #define CONFIG_SYS_MALLOC_LEN           (CONFIG_ENV_SIZE + 1024 * 1024)
  57
  58 /* Serial Port */
  59 #define CONFIG_CONS_INDEX               1
  60 #define CONFIG_SYS_NS16550_SERIAL
  61 #define CONFIG_SYS_NS16550_REG_SIZE     1
  62 #define CONFIG_SYS_NS16550_CLK          (get_serial_clock())
  63
  64 #define CONFIG_SYS_BAUDRATE_TABLE       { 9600, 19200, 38400, 57600, 115200 }
  65
  66 /* SD boot SPL */
  67 #ifdef CONFIG_SD_BOOT
  68 #define CONFIG_SPL_FRAMEWORK
  69 #define CONFIG_SPL_TARGET               "u-boot-with-spl.bin"
  70
  71 #define CONFIG_SPL_TEXT_BASE            0x10000000
  72 #define CONFIG_SPL_MAX_SIZE             0x17000
  73 #define CONFIG_SPL_STACK                0x1001e000
  74 #define CONFIG_SPL_PAD_TO               0x1d000
  75
  76 #define CONFIG_SYS_SPL_MALLOC_START     (CONFIG_SPL_BSS_START_ADDR + \
  77                                         CONFIG_SPL_BSS_MAX_SIZE)
  78 #define CONFIG_SYS_SPL_MALLOC_SIZE      0x100000
  79 #define CONFIG_SPL_BSS_START_ADDR       0x8f000000
  80 #define CONFIG_SPL_BSS_MAX_SIZE         0x80000
  81
  82 #ifdef CONFIG_SECURE_BOOT
  83 #define CONFIG_U_BOOT_HDR_SIZE                          (16 << 10)
  84 /*
  85  * HDR would be appended at end of image and copied to DDR along
  86  * with U-Boot image. Here u-boot max. size is 512K. So if binary
  87  * size increases then increase this size in case of secure boot as
  88  * it uses raw u-boot image instead of fit image.
  89  */
  90 #define CONFIG_SYS_MONITOR_LEN          (0x100000 + CONFIG_U_BOOT_HDR_SIZE)
  91 #else
  92 #define CONFIG_SYS_MONITOR_LEN          0x100000
  93 #endif /* ifdef CONFIG_SECURE_BOOT */
  94 #endif
  95
  96 /* NAND SPL */
  97 #ifdef CONFIG_NAND_BOOT
  98 #define CONFIG_SPL_PBL_PAD
  99 #define CONFIG_SPL_FRAMEWORK
 100 #define CONFIG_SPL_TARGET               "u-boot-with-spl.bin"
 101 #define CONFIG_SPL_TEXT_BASE            0x10000000
 102 #define CONFIG_SPL_MAX_SIZE             0x1a000
 103 #define CONFIG_SPL_STACK                0x1001d000
 104 #define CONFIG_SYS_NAND_U_BOOT_DST      CONFIG_SYS_TEXT_BASE
 105 #define CONFIG_SYS_NAND_U_BOOT_START    CONFIG_SYS_TEXT_BASE
 106 #define CONFIG_SYS_SPL_MALLOC_START     0x80200000
 107 #define CONFIG_SPL_BSS_START_ADDR       0x80100000
 108 #define CONFIG_SYS_SPL_MALLOC_SIZE      0x100000
 109 #define CONFIG_SPL_BSS_MAX_SIZE         0x80000
 110
 111 #ifdef CONFIG_SECURE_BOOT
 112 #define CONFIG_U_BOOT_HDR_SIZE                          (16 << 10)
 113 #endif /* ifdef CONFIG_SECURE_BOOT */
 114
 115 #ifdef CONFIG_U_BOOT_HDR_SIZE
 116 /*
 117  * HDR would be appended at end of image and copied to DDR along
 118  * with U-Boot image. Here u-boot max. size is 512K. So if binary
 119  * size increases then increase this size in case of secure boot as
 120  * it uses raw u-boot image instead of fit image.
 121  */
 122 #define CONFIG_SYS_MONITOR_LEN          (0x100000 + CONFIG_U_BOOT_HDR_SIZE)
 123 #else
 124 #define CONFIG_SYS_MONITOR_LEN          0x100000
 125 #endif /* ifdef CONFIG_U_BOOT_HDR_SIZE */
 126
 127 #endif
 128
 129 /* IFC */
 130 #ifndef SPL_NO_IFC
 131 #if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
 132 #define CONFIG_FSL_IFC
 133 /*
 134  * CONFIG_SYS_FLASH_BASE has the final address (core view)
 135  * CONFIG_SYS_FLASH_BASE_PHYS has the final address (IFC view)
 136  * CONFIG_SYS_FLASH_BASE_PHYS_EARLY has the temporary IFC address
 137  * CONFIG_SYS_TEXT_BASE is linked to 0x60000000 for booting
 138  */
 139 #define CONFIG_SYS_FLASH_BASE                   0x60000000
 140 #define CONFIG_SYS_FLASH_BASE_PHYS              CONFIG_SYS_FLASH_BASE
 141 #define CONFIG_SYS_FLASH_BASE_PHYS_EARLY        0x00000000
 142
 143 #ifdef CONFIG_MTD_NOR_FLASH
 144 #define CONFIG_FLASH_CFI_DRIVER
 145 #define CONFIG_SYS_FLASH_CFI
 146 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
 147 #define CONFIG_SYS_FLASH_QUIET_TEST
 148 #define CONFIG_FLASH_SHOW_PROGRESS      45      /* count down from 45/5: 9..1 */
 149 #endif
 150 #endif
 151 #endif
 152
 153 /* I2C */
 154 #define CONFIG_SYS_I2C
 155 #define CONFIG_SYS_I2C_MXC
 156 #define CONFIG_SYS_I2C_MXC_I2C1
 157 #define CONFIG_SYS_I2C_MXC_I2C2
 158 #define CONFIG_SYS_I2C_MXC_I2C3
 159 #define CONFIG_SYS_I2C_MXC_I2C4
 160
 161 /* PCIe */
 162 #ifndef SPL_NO_PCIE
 163 #define CONFIG_PCIE1            /* PCIE controller 1 */
 164 #define CONFIG_PCIE2            /* PCIE controller 2 */
 165 #define CONFIG_PCIE3            /* PCIE controller 3 */
 166
 167 #ifdef CONFIG_PCI
 168 #define CONFIG_NET_MULTI
 169 #define CONFIG_PCI_SCAN_SHOW
 170 #endif
 171 #endif
 172
 173 /* Command line configuration */
 174
 175 /*  MMC  */
 176 #ifndef SPL_NO_MMC
 177 #ifdef CONFIG_MMC
 178 #define CONFIG_FSL_ESDHC
 179 #define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
 180 #endif
 181 #endif
 182
 183 /*  DSPI  */
 184 #ifndef SPL_NO_DSPI
 185 #define CONFIG_FSL_DSPI
 186 #ifdef CONFIG_FSL_DSPI
 187 #define CONFIG_DM_SPI_FLASH
 188 #define CONFIG_SPI_FLASH_STMICRO        /* cs0 */
 189 #define CONFIG_SPI_FLASH_SST            /* cs1 */
 190 #define CONFIG_SPI_FLASH_EON            /* cs2 */
 191 #if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
 192 #define CONFIG_SF_DEFAULT_BUS           1
 193 #define CONFIG_SF_DEFAULT_CS            0
 194 #endif
 195 #endif
 196 #endif
 197
 198 /* FMan ucode */
 199 #ifndef SPL_NO_FMAN
 200 #define CONFIG_SYS_DPAA_FMAN
 201 #ifdef CONFIG_SYS_DPAA_FMAN
 202 #define CONFIG_SYS_FM_MURAM_SIZE        0x60000
 203
 204 #ifdef CONFIG_NAND_BOOT
 205 /* Store Fman ucode at offeset 0x900000(72 blocks). */
 206 #define CONFIG_SYS_QE_FMAN_FW_IN_NAND
 207 #define CONFIG_SYS_FMAN_FW_ADDR         (72 * CONFIG_SYS_NAND_BLOCK_SIZE)
 208 #elif defined(CONFIG_SD_BOOT)
 209 /*
 210  * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
 211  * about 1MB (2040 blocks), Env is stored after the image, and the env size is
 212  * 0x2000 (16 blocks), 8 + 2040 + 16 = 2064, enlarge it to 18432(0x4800).
 213  */
 214 #define CONFIG_SYS_QE_FMAN_FW_IN_MMC
 215 #define CONFIG_SYS_FMAN_FW_ADDR         (512 * 0x4800)
 216 #define CONFIG_SYS_QE_FW_ADDR           (512 * 0x4a08)
 217 #elif defined(CONFIG_QSPI_BOOT)
 218 #define CONFIG_SYS_QE_FW_IN_SPIFLASH
 219 #define CONFIG_SYS_FMAN_FW_ADDR         0x40900000
 220 #define CONFIG_ENV_SPI_BUS              0
 221 #define CONFIG_ENV_SPI_CS               0
 222 #define CONFIG_ENV_SPI_MAX_HZ           1000000
 223 #define CONFIG_ENV_SPI_MODE             0x03
 224 #else
 225 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR
 226 /* FMan fireware Pre-load address */
 227 #define CONFIG_SYS_FMAN_FW_ADDR         0x60900000
 228 #define CONFIG_SYS_QE_FW_ADDR           0x60940000
 229 #endif
 230 #define CONFIG_SYS_QE_FMAN_FW_LENGTH    0x10000
 231 #define CONFIG_SYS_FDT_PAD              (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
 232 #endif
 233 #endif
 234
 235 /* Miscellaneous configurable options */
 236 #define CONFIG_SYS_LOAD_ADDR    (CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000)
 237
 238 #define CONFIG_HWCONFIG
 239 #define HWCONFIG_BUFFER_SIZE            128
 240
 241 #ifndef SPL_NO_MISC
 242 #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
 243 #define MTDPARTS_DEFAULT "mtdparts=spi0.0:1m(uboot)," \
 244                         "5m(kernel),1m(dtb),9m(file_system)"
 245 #else
 246 #define MTDPARTS_DEFAULT "mtdparts=60000000.nor:" \
 247                         "2m@0x100000(nor_bank0_uboot),"\
 248                         "40m@0x1100000(nor_bank0_fit)," \
 249                         "7m(nor_bank0_user)," \
 250                         "2m@0x4100000(nor_bank4_uboot)," \
 251                         "40m@0x5100000(nor_bank4_fit),"\
 252                         "-(nor_bank4_user);" \
 253                         "7e800000.flash:" \
 254                         "1m(nand_uboot),1m(nand_uboot_env)," \
 255                         "20m(nand_fit);spi0.0:1m(uboot)," \
 256                         "5m(kernel),1m(dtb),9m(file_system)"
 257 #endif
 258
 259 #include <config_distro_defaults.h>
 260 #ifndef CONFIG_SPL_BUILD
 261 #define BOOT_TARGET_DEVICES(func) \
 262         func(MMC, mmc, 0) \
 263         func(USB, usb, 0)
 264 #include <config_distro_bootcmd.h>
 265 #endif
 266
 267 /* Initial environment variables */
 268 #define CONFIG_EXTRA_ENV_SETTINGS               \
 269         "hwconfig=fsl_ddr:bank_intlv=auto\0"    \
 270         "fdt_high=0xffffffffffffffff\0"         \
 271         "initrd_high=0xffffffffffffffff\0"      \
 272         "fdt_addr=0x64f00000\0"                 \
 273         "kernel_addr=0x65000000\0"              \
 274         "scriptaddr=0x80000000\0"               \
 275         "scripthdraddr=0x80080000\0"            \
 276         "fdtheader_addr_r=0x80100000\0"         \
 277         "kernelheader_addr_r=0x80200000\0"      \
 278         "kernel_addr_r=0x81000000\0"            \
 279         "fdt_addr_r=0x90000000\0"               \
 280         "load_addr=0xa0000000\0"                \
 281         "kernel_size=0x2800000\0"               \
 282         "console=ttyS0,115200\0"                \
 283         "boot_os=y\0"                           \
 284         "mtdparts=" MTDPARTS_DEFAULT "\0"       \
 285         BOOTENV                                 \
 286         "boot_scripts=ls1043ardb_boot.scr\0"    \
 287         "boot_script_hdr=hdr_ls1043ardb_bs.out\0"       \
 288         "scan_dev_for_boot_part="               \
 289                 "part list ${devtype} ${devnum} devplist; "     \
 290                 "env exists devplist || setenv devplist 1; "    \
 291                 "for distro_bootpart in ${devplist}; do "       \
 292                         "if fstype ${devtype} "                 \
 293                                 "${devnum}:${distro_bootpart} " \
 294                                 "bootfstype; then "             \
 295                                 "run scan_dev_for_boot; "       \
 296                         "fi; "                                  \
 297                 "done\0"                        \
 298         "scan_dev_for_boot="                                    \
 299                 "echo Scanning ${devtype} "                     \
 300                         "${devnum}:${distro_bootpart}...; "     \
 301                 "for prefix in ${boot_prefixes}; do "           \
 302                         "run scan_dev_for_scripts; "            \
 303                 "done;\0"                                       \
 304         "boot_a_script="                                        \
 305                 "load ${devtype} ${devnum}:${distro_bootpart} " \
 306                         "${scriptaddr} ${prefix}${script}; "    \
 307                 "env exists secureboot && load ${devtype} "     \
 308                         "${devnum}:${distro_bootpart} "         \
 309                         "${scripthdraddr} ${prefix}${boot_script_hdr} " \
 310                         "&& esbc_validate ${scripthdraddr};"    \
 311                 "source ${scriptaddr}\0"                        \
 312         "installer=load mmc 0:2 $load_addr "    \
 313                 "/flex_installer_arm64.itb; "   \
 314                 "bootm $load_addr#ls1043ardb\0" \
 315         "qspi_bootcmd=echo Trying load from qspi..;"    \
 316                 "sf probe && sf read $load_addr "       \
 317                 "$kernel_addr $kernel_size && bootm $load_addr#$board\0" \
 318         "nor_bootcmd=echo Trying load from nor..;"      \
 319                 "cp.b $kernel_addr $load_addr " \
 320                 "$kernel_size && bootm $load_addr#$board\0"
 321
 322 #undef CONFIG_BOOTCOMMAND
 323 #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
 324 #define CONFIG_BOOTCOMMAND "run distro_bootcmd; env exists secureboot"  \
 325                            "&& esbc_halt; run qspi_bootcmd;"
 326 #else
 327 #define CONFIG_BOOTCOMMAND "run distro_bootcmd; env exists secureboot"  \
 328                            "&& esbc_halt; run nor_bootcmd;"
 329 #endif
 330 #endif
 331
 332 /* Monitor Command Prompt */
 333 #define CONFIG_SYS_CBSIZE               512     /* Console I/O Buffer Size */
 334 #define CONFIG_SYS_LONGHELP
 335
 336 #ifndef SPL_NO_MISC
 337 #ifndef CONFIG_CMDLINE_EDITING
 338 #define CONFIG_CMDLINE_EDITING          1
 339 #endif
 340 #endif
 341
 342 #define CONFIG_AUTO_COMPLETE
 343 #define CONFIG_SYS_MAXARGS              64      /* max command args */
 344
 345 #define CONFIG_SYS_BOOTM_LEN   (64 << 20)      /* Increase max gunzip size */
 346
 347 #include <asm/arch/soc.h>
 348
 349 #endif /* __LS1043A_COMMON_H */