include/configs/ls1028ardb.h

   1 /* SPDX-License-Identifier: GPL-2.0+ */
   2 /*
   3  * Copyright 2019 NXP
   4  */
   5
   6 #ifndef __LS1028A_RDB_H
   7 #define __LS1028A_RDB_H
   8
   9 #include "ls1028a_common.h"
  10
  11 #define COUNTER_FREQUENCY_REAL          (get_board_sys_clk() / 4)
  12
  13 #define CONFIG_SYS_RTC_BUS_NUM         0
  14
  15 /* Store environment at top of flash */
  16
  17 #define CONFIG_QIXIS_I2C_ACCESS
  18
  19 /*
  20  * QIXIS Definitions
  21  */
  22 #define CONFIG_FSL_QIXIS
  23
  24 #ifdef CONFIG_FSL_QIXIS
  25 #define QIXIS_BASE                      0x7fb00000
  26 #define QIXIS_BASE_PHYS                 QIXIS_BASE
  27 #define CONFIG_SYS_I2C_FPGA_ADDR        0x66
  28 #define QIXIS_LBMAP_SWITCH              2
  29 #define QIXIS_LBMAP_MASK                0xe0
  30 #define QIXIS_LBMAP_SHIFT               0x5
  31 #define QIXIS_LBMAP_DFLTBANK            0x00
  32 #define QIXIS_LBMAP_ALTBANK             0x00
  33 #define QIXIS_LBMAP_SD                  0x00
  34 #define QIXIS_LBMAP_EMMC                0x00
  35 #define QIXIS_LBMAP_XSPI                0x00
  36 #define QIXIS_RCW_SRC_SD                0xf8
  37 #define QIXIS_RCW_SRC_EMMC              0xf9
  38 #define QIXIS_RCW_SRC_XSPI              0xff
  39 #define QIXIS_RST_CTL_RESET             0x31
  40 #define QIXIS_RCFG_CTL_RECONFIG_IDLE    0x10
  41 #define QIXIS_RCFG_CTL_RECONFIG_START   0x11
  42 #define QIXIS_RCFG_CTL_WATCHDOG_ENBLE   0x08
  43 #define QIXIS_RST_FORCE_MEM             0x01
  44
  45 #define CONFIG_SYS_FPGA_CSPR_EXT        (0x0)
  46 #define CONFIG_SYS_FPGA_CSPR            (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) | \
  47                                         CSPR_PORT_SIZE_8 | \
  48                                         CSPR_MSEL_GPCM | \
  49                                         CSPR_V)
  50 #define CONFIG_SYS_FPGA_CSOR            (CSOR_NOR_ADM_SHIFT(4) | \
  51                                         CSOR_NOR_NOR_MODE_AVD_NOR | \
  52                                         CSOR_NOR_TRHZ_80)
  53 #endif
  54
  55 /* SATA */
  56 #define SCSI_VEND_ID 0x1b4b
  57 #define SCSI_DEV_ID  0x9170
  58 #define CONFIG_SCSI_DEV_LIST {SCSI_VEND_ID, SCSI_DEV_ID}
  59 #define CONFIG_SYS_SATA1                        AHCI_BASE_ADDR1
  60
  61 /* Initial environment variables */
  62 #ifndef SPL_NO_ENV
  63 #undef CONFIG_EXTRA_ENV_SETTINGS
  64 #define CONFIG_EXTRA_ENV_SETTINGS               \
  65         "board=ls1028ardb\0"                    \
  66         "hwconfig=fsl_ddr:bank_intlv=auto\0"    \
  67         "ramdisk_addr=0x800000\0"               \
  68         "ramdisk_size=0x2000000\0"              \
  69         "bootm_size=0x10000000\0"               \
  70         "fdt_addr=0x00f00000\0"                 \
  71         "kernel_addr=0x01000000\0"              \
  72         "scriptaddr=0x80000000\0"               \
  73         "scripthdraddr=0x80080000\0"            \
  74         "fdtheader_addr_r=0x80100000\0"         \
  75         "kernelheader_addr_r=0x80200000\0"      \
  76         "load_addr=0xa0000000\0"            \
  77         "kernel_addr_r=0x81000000\0"            \
  78         "fdt_addr_r=0x90000000\0"               \
  79         "ramdisk_addr_r=0xa0000000\0"           \
  80         "kernel_start=0x1000000\0"              \
  81         "kernelheader_start=0x600000\0"         \
  82         "kernel_load=0xa0000000\0"              \
  83         "kernel_size=0x2800000\0"               \
  84         "kernelheader_size=0x40000\0"           \
  85         "kernel_addr_sd=0x8000\0"               \
  86         "kernel_size_sd=0x14000\0"              \
  87         "kernelhdr_addr_sd=0x3000\0"            \
  88         "kernelhdr_size_sd=0x20\0"              \
  89         "console=ttyS0,115200\0"                \
  90         "mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0"        \
  91         BOOTENV                                 \
  92         "boot_scripts=ls1028ardb_boot.scr\0"    \
  93         "boot_script_hdr=hdr_ls1028ardb_bs.out\0"       \
  94         "scan_dev_for_boot_part="               \
  95                 "part list ${devtype} ${devnum} devplist; "   \
  96                 "env exists devplist || setenv devplist 1; "  \
  97                 "for distro_bootpart in ${devplist}; do "     \
  98                   "if fstype ${devtype} "                  \
  99                         "${devnum}:${distro_bootpart} "      \
 100                         "bootfstype; then "                  \
 101                         "run scan_dev_for_boot; "            \
 102                   "fi; "                                   \
 103                 "done\0"                                   \
 104         "boot_a_script="                                  \
 105                 "load ${devtype} ${devnum}:${distro_bootpart} "  \
 106                         "${scriptaddr} ${prefix}${script}; "    \
 107                 "env exists secureboot && load ${devtype} "     \
 108                         "${devnum}:${distro_bootpart} "         \
 109                         "${scripthdraddr} ${prefix}${boot_script_hdr} " \
 110                         "&& esbc_validate ${scripthdraddr};"    \
 111                 "source ${scriptaddr}\0"          \
 112         "xspi_bootcmd=echo Trying load from FlexSPI flash ...;" \
 113                 "sf probe 0:0 && sf read $load_addr " \
 114                 "$kernel_start $kernel_size ; env exists secureboot &&" \
 115                 "sf read $kernelheader_addr_r $kernelheader_start " \
 116                 "$kernelheader_size && esbc_validate ${kernelheader_addr_r}; "\
 117                 " bootm $load_addr#$board\0" \
 118         "xspi_hdploadcmd=echo Trying load HDP firmware from FlexSPI...;" \
 119                 "sf probe 0:0 && sf read $load_addr 0x940000 0x30000 " \
 120                 "&& hdp load $load_addr 0x2000\0"                       \
 121         "sd_bootcmd=echo Trying load from SD ...;" \
 122                 "mmc dev 0;mmcinfo; mmc read $load_addr "               \
 123                 "$kernel_addr_sd $kernel_size_sd && "   \
 124                 "env exists secureboot && mmc read $kernelheader_addr_r " \
 125                 "$kernelhdr_addr_sd $kernelhdr_size_sd "                \
 126                 " && esbc_validate ${kernelheader_addr_r};"     \
 127                 "bootm $load_addr#$board\0"             \
 128         "sd_hdploadcmd=echo Trying load HDP firmware from SD..;"        \
 129                 "mmc dev 0;mmcinfo;mmc read $load_addr 0x4a00 0x200 "   \
 130                 "&& hdp load $load_addr 0x2000\0"       \
 131         "emmc_bootcmd=echo Trying load from EMMC ..;"   \
 132                 "mmc dev 1;mmcinfo; mmc read $load_addr "               \
 133                 "$kernel_addr_sd $kernel_size_sd && "   \
 134                 "env exists secureboot && mmc read $kernelheader_addr_r " \
 135                 "$kernelhdr_addr_sd $kernelhdr_size_sd "                \
 136                 " && esbc_validate ${kernelheader_addr_r};"     \
 137                 "bootm $load_addr#$board\0"                     \
 138         "emmc_hdploadcmd=echo Trying load HDP firmware from EMMC..;"      \
 139                 "mmc dev 1;mmcinfo;mmc read $load_addr 0x4a00 0x200 "   \
 140                 "&& hdp load $load_addr 0x2000\0"
 141 #endif
 142 #endif /* __LS1028A_RDB_H */