include/configs/ls1028aqds.h

   1 /* SPDX-License-Identifier: GPL-2.0+ */
   2 /*
   3  * Copyright 2019-2020 NXP
   4  */
   5
   6 #ifndef __LS1028A_QDS_H
   7 #define __LS1028A_QDS_H
   8
   9 #include "ls1028a_common.h"
  10
  11 #define CONFIG_SYS_CLK_FREQ             100000000
  12 #define CONFIG_DDR_CLK_FREQ             100000000
  13 #define COUNTER_FREQUENCY_REAL          (CONFIG_SYS_CLK_FREQ / 4)
  14
  15 /* DDR */
  16 #define CONFIG_DIMM_SLOTS_PER_CTLR              2
  17
  18 #define CONFIG_QIXIS_I2C_ACCESS
  19
  20 /*
  21  * QIXIS Definitions
  22  */
  23 #define CONFIG_FSL_QIXIS
  24
  25 #ifdef CONFIG_FSL_QIXIS
  26 #define QIXIS_BASE                      0x7fb00000
  27 #define QIXIS_BASE_PHYS                 QIXIS_BASE
  28 #define CONFIG_SYS_I2C_FPGA_ADDR        0x66
  29 #define QIXIS_LBMAP_SWITCH              1
  30 #define QIXIS_LBMAP_MASK                0x0f
  31 #define QIXIS_LBMAP_SHIFT               5
  32 #define QIXIS_LBMAP_DFLTBANK            0x00
  33 #define QIXIS_LBMAP_ALTBANK             0x00
  34 #define QIXIS_LBMAP_SD                  0x00
  35 #define QIXIS_LBMAP_EMMC                0x00
  36 #define QIXIS_LBMAP_QSPI                0x00
  37 #define QIXIS_RCW_SRC_SD                0x8
  38 #define QIXIS_RCW_SRC_EMMC              0x9
  39 #define QIXIS_RCW_SRC_QSPI              0xf
  40 #define QIXIS_RST_CTL_RESET             0x31
  41 #define QIXIS_RCFG_CTL_RECONFIG_IDLE    0x20
  42 #define QIXIS_RCFG_CTL_RECONFIG_START   0x21
  43 #define QIXIS_RCFG_CTL_WATCHDOG_ENBLE   0x08
  44 #define QIXIS_RST_FORCE_MEM             0x01
  45
  46 #define CONFIG_SYS_FPGA_CSPR_EXT        (0x0)
  47 #define CONFIG_SYS_FPGA_CSPR            (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) | \
  48                                         CSPR_PORT_SIZE_8 | \
  49                                         CSPR_MSEL_GPCM | \
  50                                         CSPR_V)
  51 #define CONFIG_SYS_FPGA_AMASK           IFC_AMASK(64 * 1024)
  52 #define CONFIG_SYS_FPGA_CSOR            (CSOR_NOR_ADM_SHIFT(4) | \
  53                                         CSOR_NOR_NOR_MODE_AVD_NOR | \
  54                                         CSOR_NOR_TRHZ_80)
  55 #endif
  56
  57 /* RTC */
  58 #define CONFIG_SYS_RTC_BUS_NUM         1
  59 #define I2C_MUX_CH_RTC                 0xB
  60
  61 /* Store environment at top of flash */
  62
  63 #ifdef CONFIG_SPL_BUILD
  64 #define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE
  65 #else
  66 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
  67 #endif
  68
  69 /* LPUART */
  70 #ifdef CONFIG_LPUART
  71 #define CONFIG_LPUART_32B_REG
  72 #define CFG_LPUART_MUX_MASK     0xf0
  73 #define CFG_LPUART_EN           0xf0
  74 #endif
  75
  76 /* SATA */
  77 #define CONFIG_SCSI_AHCI_PLAT
  78
  79 #define CONFIG_SYS_SATA1                        AHCI_BASE_ADDR1
  80 #define CONFIG_SYS_SCSI_MAX_SCSI_ID             1
  81 #define CONFIG_SYS_SCSI_MAX_LUN                 1
  82 #define CONFIG_SYS_SCSI_MAX_DEVICE              (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
  83                                                 CONFIG_SYS_SCSI_MAX_LUN)
  84 #ifndef SPL_NO_ENV
  85 #undef CONFIG_EXTRA_ENV_SETTINGS
  86 #define CONFIG_EXTRA_ENV_SETTINGS \
  87         "board=ls1028aqds\0" \
  88         "hwconfig=fsl_ddr:bank_intlv=auto\0" \
  89         "ramdisk_addr=0x800000\0" \
  90         "ramdisk_size=0x2000000\0" \
  91         "fdt_addr=0x00f00000\0" \
  92         "kernel_addr=0x01000000\0" \
  93         "scriptaddr=0x80000000\0" \
  94         "scripthdraddr=0x80080000\0" \
  95         "fdtheader_addr_r=0x80100000\0" \
  96         "kernelheader_addr_r=0x80200000\0" \
  97         "load_addr=0xa0000000\0" \
  98         "kernel_addr_r=0x81000000\0" \
  99         "fdt_addr_r=0x90000000\0" \
 100         "fdt2_addr_r=0x90010000\0" \
 101         "ramdisk_addr_r=0xa0000000\0" \
 102         "kernel_start=0x1000000\0" \
 103         "kernelheader_start=0x600000\0" \
 104         "kernel_load=0xa0000000\0" \
 105         "kernel_size=0x2800000\0" \
 106         "kernelheader_size=0x40000\0" \
 107         "kernel_addr_sd=0x8000\0" \
 108         "kernel_size_sd=0x14000\0" \
 109         "kernelhdr_addr_sd=0x3000\0" \
 110         "kernelhdr_size_sd=0x10\0" \
 111         "console=ttyS0,115200\0" \
 112         "mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0" \
 113         BOOTENV \
 114         "boot_scripts=ls1028aqds_boot.scr\0" \
 115         "boot_script_hdr=hdr_ls1028aqds_bs.out\0" \
 116         "scan_dev_for_boot_part=" \
 117                 "part list ${devtype} ${devnum} devplist; " \
 118                 "env exists devplist || setenv devplist 1; " \
 119                 "for distro_bootpart in ${devplist}; do " \
 120                   "if fstype ${devtype} " \
 121                         "${devnum}:${distro_bootpart} " \
 122                         "bootfstype; then " \
 123                         "run scan_dev_for_boot; " \
 124                   "fi; " \
 125                 "done\0" \
 126         "boot_a_script=" \
 127                 "load ${devtype} ${devnum}:${distro_bootpart} " \
 128                         "${scriptaddr} ${prefix}${script}; " \
 129                 "env exists secureboot && load ${devtype} " \
 130                         "${devnum}:${distro_bootpart} " \
 131                         "${scripthdraddr} ${prefix}${boot_script_hdr} " \
 132                         "&& esbc_validate ${scripthdraddr};" \
 133                 "source ${scriptaddr}\0" \
 134         "xspi_bootcmd=echo Trying load from FlexSPI flash ...;" \
 135                 "sf probe 0:0 && sf read $load_addr " \
 136                 "$kernel_start $kernel_size ; env exists secureboot &&" \
 137                 "sf read $kernelheader_addr_r $kernelheader_start " \
 138                 "$kernelheader_size && esbc_validate ${kernelheader_addr_r}; "\
 139                 " bootm $load_addr#$board\0" \
 140         "xspi_hdploadcmd=echo Trying load HDP firmware from FlexSPI...;" \
 141                 "sf probe 0:0 && sf read $load_addr 0x940000 0x30000 " \
 142                 "&& hdp load $load_addr 0x2000\0"                       \
 143         "sd_bootcmd=echo Trying load from SD ...;" \
 144                 "mmc dev 0; mmcinfo; mmc read $load_addr "              \
 145                 "$kernel_addr_sd $kernel_size_sd && "   \
 146                 "env exists secureboot && mmc read $kernelheader_addr_r " \
 147                 "$kernelhdr_addr_sd $kernelhdr_size_sd "                \
 148                 " && esbc_validate ${kernelheader_addr_r};"     \
 149                 "bootm $load_addr#$board\0"             \
 150         "sd_hdploadcmd=echo Trying load HDP firmware from SD..;"        \
 151                 "mmc dev 0;mmcinfo; mmc read $load_addr 0x4a00 0x200 "  \
 152                 "&& hdp load $load_addr 0x2000\0"       \
 153         "emmc_bootcmd=echo Trying load from EMMC ..;"   \
 154                 "mmc dev 1; mmcinfo; mmc read $load_addr "              \
 155                 "$kernel_addr_sd $kernel_size_sd && "   \
 156                 "env exists secureboot && mmc read $kernelheader_addr_r " \
 157                 "$kernelhdr_addr_sd $kernelhdr_size_sd "                \
 158                 " && esbc_validate ${kernelheader_addr_r};"     \
 159                 "bootm $load_addr#$board\0"                     \
 160         "emmc_hdploadcmd=echo Trying load HDP firmware from EMMC..;"      \
 161                 "mmc dev 1;mmcinfo;mmc read $load_addr 0x4a00 0x200 "   \
 162                 "&& hdp load $load_addr 0x2000\0"
 163
 164 #endif
 165 #endif /* __LS1028A_QDS_H */