include/configs/ls1012aqds.h

   1 /*
   2  * Copyright 2016 Freescale Semiconductor, Inc.
   3  *
   4  * SPDX-License-Identifier:     GPL-2.0+
   5  */
   6
   7 #ifndef __LS1012AQDS_H__
   8 #define __LS1012AQDS_H__
   9
  10 #include "ls1012a_common.h"
  11
  12 /* DDR */
  13 #define CONFIG_DIMM_SLOTS_PER_CTLR      1
  14 #define CONFIG_CHIP_SELECTS_PER_CTRL    1
  15 #define CONFIG_NR_DRAM_BANKS            2
  16 #define CONFIG_SYS_SDRAM_SIZE           0x40000000
  17 #define CONFIG_CMD_MEMINFO
  18 #define CONFIG_CMD_MEMTEST
  19 #define CONFIG_SYS_MEMTEST_START        0x80000000
  20 #define CONFIG_SYS_MEMTEST_END          0x9fffffff
  21
  22 /*
  23  * QIXIS Definitions
  24  */
  25 #define CONFIG_FSL_QIXIS
  26
  27 #ifdef CONFIG_FSL_QIXIS
  28 #define CONFIG_QIXIS_I2C_ACCESS
  29 #define CONFIG_SYS_I2C_FPGA_ADDR        0x66
  30 #define QIXIS_LBMAP_BRDCFG_REG          0x04
  31 #define QIXIS_LBMAP_SWITCH              6
  32 #define QIXIS_LBMAP_MASK                0x08
  33 #define QIXIS_LBMAP_SHIFT               0
  34 #define QIXIS_LBMAP_DFLTBANK            0x00
  35 #define QIXIS_LBMAP_ALTBANK             0x08
  36 #define QIXIS_RST_CTL_RESET             0x31
  37 #define QIXIS_RCFG_CTL_RECONFIG_IDLE    0x20
  38 #define QIXIS_RCFG_CTL_RECONFIG_START   0x21
  39 #define QIXIS_RCFG_CTL_WATCHDOG_ENBLE   0x08
  40 #endif
  41
  42 /*
  43  * I2C bus multiplexer
  44  */
  45 #define I2C_MUX_PCA_ADDR_PRI            0x77
  46 #define I2C_MUX_PCA_ADDR_SEC            0x76 /* Secondary multiplexer */
  47 #define I2C_RETIMER_ADDR                0x18
  48 #define I2C_MUX_CH_DEFAULT              0x8
  49 #define I2C_MUX_CH_CH7301               0xC
  50 #define I2C_MUX_CH5                     0xD
  51 #define I2C_MUX_CH7                     0xF
  52
  53 #define I2C_MUX_CH_VOL_MONITOR 0xa
  54
  55 /*
  56 * RTC configuration
  57 */
  58 #define RTC
  59 #define CONFIG_RTC_PCF8563 1
  60 #define CONFIG_SYS_I2C_RTC_ADDR         0x51  /* Channel 3*/
  61
  62 /* EEPROM */
  63 #define CONFIG_ID_EEPROM
  64 #define CONFIG_SYS_I2C_EEPROM_NXID
  65 #define CONFIG_SYS_EEPROM_BUS_NUM    0
  66 #define CONFIG_SYS_I2C_EEPROM_ADDR   0x57
  67 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN     1
  68 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
  69 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
  70
  71
  72 /* Voltage monitor on channel 2*/
  73 #define I2C_VOL_MONITOR_ADDR           0x40
  74 #define I2C_VOL_MONITOR_BUS_V_OFFSET   0x2
  75 #define I2C_VOL_MONITOR_BUS_V_OVF      0x1
  76 #define I2C_VOL_MONITOR_BUS_V_SHIFT    3
  77
  78 /* DSPI */
  79 #define CONFIG_FSL_DSPI1
  80 #define CONFIG_DEFAULT_SPI_BUS 1
  81
  82 #define CONFIG_CMD_SPI
  83 #define MMAP_DSPI          DSPI1_BASE_ADDR
  84
  85 #define CONFIG_SYS_DSPI_CTAR0   1
  86
  87 #define CONFIG_SYS_DSPI_CTAR1   (DSPI_CTAR_TRSZ(7) | DSPI_CTAR_PCSSCK_1CLK |\
  88                                 DSPI_CTAR_PASC(0) | DSPI_CTAR_PDT(0) | \
  89                                 DSPI_CTAR_CSSCK(2) | DSPI_CTAR_ASC(0) | \
  90                                 DSPI_CTAR_DT(0))
  91 #define CONFIG_SPI_FLASH_SST /* cs1 */
  92
  93 #define CONFIG_SYS_DSPI_CTAR2   (DSPI_CTAR_TRSZ(7) | DSPI_CTAR_PCSSCK_1CLK |\
  94                                 DSPI_CTAR_PASC(0) | DSPI_CTAR_PDT(0) | \
  95                                 DSPI_CTAR_CSSCK(0) | DSPI_CTAR_ASC(0) | \
  96                                 DSPI_CTAR_DT(0))
  97 #define CONFIG_SPI_FLASH_STMICRO /* cs2 */
  98
  99 #define CONFIG_SYS_DSPI_CTAR3   (DSPI_CTAR_TRSZ(7) | DSPI_CTAR_PCSSCK_1CLK |\
 100                                 DSPI_CTAR_PASC(0) | DSPI_CTAR_PDT(0) | \
 101                                 DSPI_CTAR_CSSCK(2) | DSPI_CTAR_ASC(0) | \
 102                                 DSPI_CTAR_DT(0))
 103 #define CONFIG_SPI_FLASH_EON /* cs3 */
 104
 105 #define CONFIG_SF_DEFAULT_SPEED      10000000
 106 #define CONFIG_SF_DEFAULT_MODE       SPI_MODE_0
 107 #define CONFIG_SF_DEFAULT_BUS        1
 108 #define CONFIG_SF_DEFAULT_CS         0
 109
 110 /*
 111 * USB
 112 */
 113 /* EHCI Support - disbaled by default */
 114 /*#define CONFIG_HAS_FSL_DR_USB*/
 115
 116 #ifdef CONFIG_HAS_FSL_DR_USB
 117 #define CONFIG_USB_EHCI_FSL
 118 #define CONFIG_USB_ULPI
 119 #define CONFIG_USB_ULPI_VIEWPORT
 120 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 121 #endif
 122
 123 /*XHCI Support - enabled by default*/
 124 #define CONFIG_HAS_FSL_XHCI_USB
 125
 126 #ifdef CONFIG_HAS_FSL_XHCI_USB
 127 #define CONFIG_USB_XHCI_FSL
 128 #define CONFIG_USB_MAX_CONTROLLER_COUNT         1
 129 #endif
 130
 131 /*  MMC  */
 132 #ifdef CONFIG_MMC
 133 #define CONFIG_FSL_ESDHC
 134 #define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
 135 #endif
 136
 137 /* SATA */
 138 #define CONFIG_LIBATA
 139 #define CONFIG_SCSI_AHCI
 140 #define CONFIG_SCSI_AHCI_PLAT
 141
 142 #define CONFIG_SYS_SATA                         AHCI_BASE_ADDR
 143
 144 #define CONFIG_SYS_SCSI_MAX_SCSI_ID             1
 145 #define CONFIG_SYS_SCSI_MAX_LUN                 1
 146 #define CONFIG_SYS_SCSI_MAX_DEVICE              (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
 147                                                 CONFIG_SYS_SCSI_MAX_LUN)
 148
 149 #define CONFIG_PCIE1            /* PCIE controller 1 */
 150
 151 #define CONFIG_NET_MULTI
 152 #define CONFIG_PCI_SCAN_SHOW
 153
 154 #define CONFIG_CMD_MEMINFO
 155 #define CONFIG_CMD_MEMTEST
 156 #define CONFIG_SYS_MEMTEST_START        0x80000000
 157 #define CONFIG_SYS_MEMTEST_END          0x9fffffff
 158
 159 #define CONFIG_MISC_INIT_R
 160
 161 #endif /* __LS1012AQDS_H__ */