include/configs/ls1012aqds.h

   1 /* SPDX-License-Identifier: GPL-2.0+ */
   2 /*
   3  * Copyright 2016 Freescale Semiconductor, Inc.
   4  * Copyright 2021 NXP
   5  */
   6
   7 #ifndef __LS1012AQDS_H__
   8 #define __LS1012AQDS_H__
   9
  10 #include "ls1012a_common.h"
  11
  12 /* DDR */
  13 #define CONFIG_DIMM_SLOTS_PER_CTLR      1
  14 #define CONFIG_CHIP_SELECTS_PER_CTRL    1
  15 #define CONFIG_SYS_SDRAM_SIZE           0x40000000
  16
  17 /*
  18  * QIXIS Definitions
  19  */
  20 #define CONFIG_FSL_QIXIS
  21
  22 #ifdef CONFIG_FSL_QIXIS
  23 #define CONFIG_QIXIS_I2C_ACCESS
  24 #define CONFIG_SYS_I2C_FPGA_ADDR        0x66
  25 #define QIXIS_LBMAP_BRDCFG_REG          0x04
  26 #define QIXIS_LBMAP_SWITCH              6
  27 #define QIXIS_LBMAP_MASK                0x08
  28 #define QIXIS_LBMAP_SHIFT               0
  29 #define QIXIS_LBMAP_DFLTBANK            0x00
  30 #define QIXIS_LBMAP_ALTBANK             0x08
  31 #define QIXIS_RST_CTL_RESET             0x31
  32 #define QIXIS_RCFG_CTL_RECONFIG_IDLE    0x20
  33 #define QIXIS_RCFG_CTL_RECONFIG_START   0x21
  34 #define QIXIS_RCFG_CTL_WATCHDOG_ENBLE   0x08
  35 #endif
  36
  37 /*
  38  * I2C bus multiplexer
  39  */
  40 #define I2C_MUX_PCA_ADDR_PRI            0x77
  41 #define I2C_MUX_PCA_ADDR_SEC            0x76 /* Secondary multiplexer */
  42 #define I2C_RETIMER_ADDR                0x18
  43 #define I2C_MUX_CH_DEFAULT              0x8
  44 #define I2C_MUX_CH_CH7301               0xC
  45 #define I2C_MUX_CH5                     0xD
  46 #define I2C_MUX_CH7                     0xF
  47
  48 #define I2C_MUX_CH_VOL_MONITOR 0xa
  49
  50 /*
  51 * RTC configuration
  52 */
  53 #define RTC
  54 #define CONFIG_SYS_I2C_RTC_ADDR         0x51  /* Channel 3*/
  55
  56 /* EEPROM */
  57 #define CONFIG_SYS_I2C_EEPROM_NXID
  58 #define CONFIG_SYS_EEPROM_BUS_NUM    0
  59 #define CONFIG_SYS_I2C_EEPROM_ADDR   0x57
  60 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN     1
  61 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
  62 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
  63
  64
  65 /* Voltage monitor on channel 2*/
  66 #define I2C_VOL_MONITOR_ADDR           0x40
  67 #define I2C_VOL_MONITOR_BUS_V_OFFSET   0x2
  68 #define I2C_VOL_MONITOR_BUS_V_OVF      0x1
  69 #define I2C_VOL_MONITOR_BUS_V_SHIFT    3
  70
  71 /* DSPI */
  72 #define CONFIG_FSL_DSPI1
  73
  74 #define MMAP_DSPI          DSPI1_BASE_ADDR
  75
  76 #define CONFIG_SYS_DSPI_CTAR0   1
  77
  78 #define CONFIG_SYS_DSPI_CTAR1   (DSPI_CTAR_TRSZ(7) | DSPI_CTAR_PCSSCK_1CLK |\
  79                                 DSPI_CTAR_PASC(0) | DSPI_CTAR_PDT(0) | \
  80                                 DSPI_CTAR_CSSCK(2) | DSPI_CTAR_ASC(0) | \
  81                                 DSPI_CTAR_DT(0))
  82 #define CONFIG_SPI_FLASH_SST /* cs1 */
  83
  84 #define CONFIG_SYS_DSPI_CTAR2   (DSPI_CTAR_TRSZ(7) | DSPI_CTAR_PCSSCK_1CLK |\
  85                                 DSPI_CTAR_PASC(0) | DSPI_CTAR_PDT(0) | \
  86                                 DSPI_CTAR_CSSCK(0) | DSPI_CTAR_ASC(0) | \
  87                                 DSPI_CTAR_DT(0))
  88 #define CONFIG_SPI_FLASH_STMICRO /* cs2 */
  89
  90 #define CONFIG_SYS_DSPI_CTAR3   (DSPI_CTAR_TRSZ(7) | DSPI_CTAR_PCSSCK_1CLK |\
  91                                 DSPI_CTAR_PASC(0) | DSPI_CTAR_PDT(0) | \
  92                                 DSPI_CTAR_CSSCK(2) | DSPI_CTAR_ASC(0) | \
  93                                 DSPI_CTAR_DT(0))
  94 #define CONFIG_SPI_FLASH_EON /* cs3 */
  95
  96 #define CONFIG_PCIE1            /* PCIE controller 1 */
  97
  98 #define CONFIG_PCI_SCAN_SHOW
  99
 100 #undef CONFIG_EXTRA_ENV_SETTINGS
 101 #define CONFIG_EXTRA_ENV_SETTINGS               \
 102         "verify=no\0"                           \
 103         "fdt_addr=0x00f00000\0"                 \
 104         "kernel_addr=0x01000000\0"              \
 105         "kernelheader_addr=0x600000\0"          \
 106         "scriptaddr=0x80000000\0"               \
 107         "scripthdraddr=0x80080000\0"            \
 108         "fdtheader_addr_r=0x80100000\0"         \
 109         "kernelheader_addr_r=0x80200000\0"      \
 110         "kernel_addr_r=0x96000000\0"            \
 111         "fdt_addr_r=0x90000000\0"               \
 112         "load_addr=0xa0000000\0"                \
 113         "kernel_size=0x2800000\0"               \
 114         "kernelheader_size=0x40000\0"           \
 115         "console=ttyS0,115200\0"                \
 116         BOOTENV                                 \
 117         "boot_scripts=ls1012aqds_boot.scr\0"    \
 118         "boot_script_hdr=hdr_ls1012aqds_bs.out\0"       \
 119         "scan_dev_for_boot_part="               \
 120              "part list ${devtype} ${devnum} devplist; "        \
 121              "env exists devplist || setenv devplist 1; "       \
 122              "for distro_bootpart in ${devplist}; do "          \
 123                   "if fstype ${devtype} "                       \
 124                       "${devnum}:${distro_bootpart} "           \
 125                       "bootfstype; then "                       \
 126                       "run scan_dev_for_boot; " \
 127                   "fi; "                        \
 128               "done\0"                          \
 129         "boot_a_script="                                  \
 130                 "load ${devtype} ${devnum}:${distro_bootpart} "  \
 131                         "${scriptaddr} ${prefix}${script}; "    \
 132                 "env exists secureboot && load ${devtype} "     \
 133                         "${devnum}:${distro_bootpart} "         \
 134                         "${scripthdraddr} ${prefix}${boot_script_hdr}; " \
 135                         "env exists secureboot "        \
 136                         "&& esbc_validate ${scripthdraddr};"    \
 137                 "source ${scriptaddr}\0"          \
 138         "qspi_bootcmd=echo Trying load from qspi..;"    \
 139                 "sf probe 0:0 && sf read $load_addr "   \
 140                 "$kernel_addr $kernel_size; env exists secureboot "     \
 141                 "&& sf read $kernelheader_addr_r $kernelheader_addr "   \
 142                 "$kernelheader_size && esbc_validate ${kernelheader_addr_r}; " \
 143                 "bootm $load_addr#$board\0"
 144
 145 #undef CONFIG_BOOTCOMMAND
 146 #ifdef CONFIG_TFABOOT
 147 #undef QSPI_NOR_BOOTCOMMAND
 148 #define QSPI_NOR_BOOTCOMMAND "run distro_bootcmd; run qspi_bootcmd; "\
 149                              "env exists secureboot && esbc_halt;"
 150 #else
 151 #define CONFIG_BOOTCOMMAND "run distro_bootcmd; run qspi_bootcmd; "\
 152                            "env exists secureboot && esbc_halt;"
 153 #endif
 154
 155 #include <asm/fsl_secure_boot.h>
 156 #endif /* __LS1012AQDS_H__ */