include/configs/ls1012aqds.h

   1 /* SPDX-License-Identifier: GPL-2.0+ */
   2 /*
   3  * Copyright 2016 Freescale Semiconductor, Inc.
   4  * Copyright 2021 NXP
   5  */
   6
   7 #ifndef __LS1012AQDS_H__
   8 #define __LS1012AQDS_H__
   9
  10 #include "ls1012a_common.h"
  11
  12 /* DDR */
  13 #define CFG_SYS_SDRAM_SIZE              0x40000000
  14
  15 /*
  16  * QIXIS Definitions
  17  */
  18
  19 #ifdef CONFIG_FSL_QIXIS
  20 #define CFG_SYS_I2C_FPGA_ADDR   0x66
  21 #define QIXIS_LBMAP_BRDCFG_REG          0x04
  22 #define QIXIS_LBMAP_SWITCH              6
  23 #define QIXIS_LBMAP_MASK                0x08
  24 #define QIXIS_LBMAP_SHIFT               0
  25 #define QIXIS_LBMAP_DFLTBANK            0x00
  26 #define QIXIS_LBMAP_ALTBANK             0x08
  27 #define QIXIS_RST_CTL_RESET             0x31
  28 #define QIXIS_RCFG_CTL_RECONFIG_IDLE    0x20
  29 #define QIXIS_RCFG_CTL_RECONFIG_START   0x21
  30 #define QIXIS_RCFG_CTL_WATCHDOG_ENBLE   0x08
  31 #endif
  32
  33 /*
  34  * I2C bus multiplexer
  35  */
  36 #define I2C_MUX_PCA_ADDR_PRI            0x77
  37 #define I2C_MUX_PCA_ADDR_SEC            0x76 /* Secondary multiplexer */
  38 #define I2C_RETIMER_ADDR                0x18
  39 #define I2C_MUX_CH_DEFAULT              0x8
  40 #define I2C_MUX_CH_CH7301               0xC
  41 #define I2C_MUX_CH5                     0xD
  42 #define I2C_MUX_CH7                     0xF
  43
  44 #define I2C_MUX_CH_VOL_MONITOR 0xa
  45
  46 /*
  47 * RTC configuration
  48 */
  49 #define CFG_SYS_I2C_RTC_ADDR         0x51  /* Channel 3*/
  50
  51
  52 /* Voltage monitor on channel 2*/
  53 #define I2C_VOL_MONITOR_ADDR           0x40
  54 #define I2C_VOL_MONITOR_BUS_V_OFFSET   0x2
  55 #define I2C_VOL_MONITOR_BUS_V_OVF      0x1
  56 #define I2C_VOL_MONITOR_BUS_V_SHIFT    3
  57
  58 #undef CFG_EXTRA_ENV_SETTINGS
  59 #define CFG_EXTRA_ENV_SETTINGS          \
  60         "verify=no\0"                           \
  61         "kernel_addr=0x01000000\0"              \
  62         "kernelheader_addr=0x600000\0"          \
  63         "scriptaddr=0x80000000\0"               \
  64         "scripthdraddr=0x80080000\0"            \
  65         "fdtheader_addr_r=0x80100000\0"         \
  66         "kernelheader_addr_r=0x80200000\0"      \
  67         "kernel_addr_r=0x96000000\0"            \
  68         "fdt_addr_r=0x90000000\0"               \
  69         "load_addr=0xa0000000\0"                \
  70         "kernel_size=0x2800000\0"               \
  71         "kernelheader_size=0x40000\0"           \
  72         "console=ttyS0,115200\0"                \
  73         BOOTENV                                 \
  74         "boot_scripts=ls1012aqds_boot.scr\0"    \
  75         "boot_script_hdr=hdr_ls1012aqds_bs.out\0"       \
  76         "scan_dev_for_boot_part="               \
  77              "part list ${devtype} ${devnum} devplist; "        \
  78              "env exists devplist || setenv devplist 1; "       \
  79              "for distro_bootpart in ${devplist}; do "          \
  80                   "if fstype ${devtype} "                       \
  81                       "${devnum}:${distro_bootpart} "           \
  82                       "bootfstype; then "                       \
  83                       "run scan_dev_for_boot; " \
  84                   "fi; "                        \
  85               "done\0"                          \
  86         "boot_a_script="                                  \
  87                 "load ${devtype} ${devnum}:${distro_bootpart} "  \
  88                         "${scriptaddr} ${prefix}${script}; "    \
  89                 "env exists secureboot && load ${devtype} "     \
  90                         "${devnum}:${distro_bootpart} "         \
  91                         "${scripthdraddr} ${prefix}${boot_script_hdr}; " \
  92                         "env exists secureboot "        \
  93                         "&& esbc_validate ${scripthdraddr};"    \
  94                 "source ${scriptaddr}\0"          \
  95         "qspi_bootcmd=echo Trying load from qspi..;"    \
  96                 "sf probe 0:0 && sf read $load_addr "   \
  97                 "$kernel_addr $kernel_size; env exists secureboot "     \
  98                 "&& sf read $kernelheader_addr_r $kernelheader_addr "   \
  99                 "$kernelheader_size && esbc_validate ${kernelheader_addr_r}; " \
 100                 "bootm $load_addr#$board\0"
 101
 102 #ifdef CONFIG_TFABOOT
 103 #undef QSPI_NOR_BOOTCOMMAND
 104 #define QSPI_NOR_BOOTCOMMAND "run distro_bootcmd; run qspi_bootcmd; "\
 105                              "env exists secureboot && esbc_halt;"
 106 #endif
 107
 108 #include <asm/fsl_secure_boot.h>
 109 #endif /* __LS1012AQDS_H__ */