include/configs/ls1012a_common.h

   1 /* SPDX-License-Identifier: GPL-2.0+ */
   2 /*
   3  * Copyright 2016 Freescale Semiconductor
   4  */
   5
   6 #ifndef __LS1012A_COMMON_H
   7 #define __LS1012A_COMMON_H
   8
   9 #define CONFIG_FSL_LAYERSCAPE
  10 #define CONFIG_GICV2
  11
  12 #include <asm/arch/config.h>
  13 #include <asm/arch/stream_id_lsch2.h>
  14
  15 #define CONFIG_SYS_CLK_FREQ             125000000
  16
  17 #define CONFIG_SKIP_LOWLEVEL_INIT
  18
  19 #define CONFIG_SYS_INIT_SP_ADDR         (CONFIG_SYS_FSL_OCRAM_BASE + 0xfff0)
  20 #define CONFIG_SYS_LOAD_ADDR    (CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000)
  21
  22 #define CONFIG_SYS_DDR_SDRAM_BASE       0x80000000
  23 #define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY       0
  24 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE
  25 #define CONFIG_SYS_DDR_BLOCK2_BASE     0x880000000ULL
  26
  27 /* Generic Timer Definitions */
  28 #define COUNTER_FREQUENCY               25000000        /* 25MHz */
  29
  30 /* CSU */
  31 #define CONFIG_LAYERSCAPE_NS_ACCESS
  32
  33 /* Size of malloc() pool */
  34 #define CONFIG_SYS_MALLOC_LEN           (CONFIG_ENV_SIZE + 128 * 1024)
  35
  36 /*SPI device */
  37 #ifdef CONFIG_QSPI_BOOT
  38 #define CONFIG_SYS_QE_FW_IN_SPIFLASH
  39 #define CONFIG_SYS_FMAN_FW_ADDR         0x400d0000
  40 #define CONFIG_ENV_SPI_BUS              0
  41 #define CONFIG_ENV_SPI_CS               0
  42 #define CONFIG_ENV_SPI_MAX_HZ           1000000
  43 #define CONFIG_ENV_SPI_MODE             0x03
  44 #define CONFIG_SPI_FLASH_SPANSION
  45 #define CONFIG_FSL_SPI_INTERFACE
  46 #define CONFIG_SF_DATAFLASH
  47
  48 #define CONFIG_FSL_QSPI
  49 #define QSPI0_AMBA_BASE         0x40000000
  50 #define CONFIG_SPI_FLASH_SPANSION
  51
  52 #define FSL_QSPI_FLASH_SIZE             SZ_64M
  53 #define FSL_QSPI_FLASH_NUM              2
  54
  55 /*
  56  * Environment
  57  */
  58 #define CONFIG_ENV_OVERWRITE
  59
  60 #define CONFIG_ENV_SIZE                 0x40000          /* 256KB */
  61 #define CONFIG_ENV_OFFSET               0x300000        /* 3MB */
  62 #define CONFIG_ENV_SECT_SIZE            0x40000
  63 #endif
  64
  65 /* SATA */
  66 #define CONFIG_SCSI_AHCI_PLAT
  67
  68 #define CONFIG_SYS_SATA                         AHCI_BASE_ADDR
  69
  70 #define CONFIG_SYS_SCSI_MAX_SCSI_ID             1
  71 #define CONFIG_SYS_SCSI_MAX_LUN                 1
  72 #define CONFIG_SYS_SCSI_MAX_DEVICE              (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
  73                                                 CONFIG_SYS_SCSI_MAX_LUN)
  74
  75 /* I2C */
  76 #define CONFIG_SYS_I2C
  77
  78 #define CONFIG_SYS_NS16550_SERIAL
  79 #define CONFIG_SYS_NS16550_REG_SIZE     1
  80 #define CONFIG_SYS_NS16550_CLK          (get_serial_clock())
  81
  82 #define CONFIG_SYS_BAUDRATE_TABLE       { 9600, 19200, 38400, 57600, 115200 }
  83
  84 #define CONFIG_SYS_HZ                   1000
  85
  86 #define CONFIG_HWCONFIG
  87 #define HWCONFIG_BUFFER_SIZE            128
  88
  89 #ifndef CONFIG_SPL_BUILD
  90 #define BOOT_TARGET_DEVICES(func) \
  91         func(SCSI, scsi, 0) \
  92         func(MMC, mmc, 0) \
  93         func(USB, usb, 0)
  94 #include <config_distro_bootcmd.h>
  95 #endif
  96
  97 /* Initial environment variables */
  98 #define CONFIG_EXTRA_ENV_SETTINGS               \
  99         "verify=no\0"                           \
 100         "loadaddr=0x80100000\0"                 \
 101         "kernel_addr=0x100000\0"                \
 102         "fdt_high=0xffffffffffffffff\0"         \
 103         "initrd_high=0xffffffffffffffff\0"      \
 104         "kernel_start=0x1000000\0"              \
 105         "kernel_load=0xa0000000\0"              \
 106         "kernel_size=0x2800000\0"               \
 107
 108 #undef CONFIG_BOOTCOMMAND
 109 #define CONFIG_BOOTCOMMAND      "pfe stop; sf probe 0:0; sf read $kernel_load "\
 110                                 "$kernel_start $kernel_size && "\
 111                                 "bootm $kernel_load"
 112
 113 /* Monitor Command Prompt */
 114 #define CONFIG_SYS_CBSIZE               512     /* Console I/O Buffer Size */
 115 #define CONFIG_SYS_MAXARGS              64      /* max command args */
 116
 117 #define CONFIG_SYS_BOOTM_LEN   (64 << 20)      /* Increase max gunzip size */
 118
 119 #include <asm/arch/soc.h>
 120
 121 #endif /* __LS1012A_COMMON_H */