include/configs/km/kmp204x-common.h

   1 /*
   2  * (C) Copyright 2013 Keymile AG
   3  * Valentin Longchamp <valentin.longchamp@keymile.com>
   4  *
   5  * SPDX-License-Identifier:     GPL-2.0+
   6  */
   7
   8 #ifndef _CONFIG_KMP204X_H
   9 #define _CONFIG_KMP204X_H
  10
  11 #define CONFIG_SYS_TEXT_BASE    0xfff40000
  12
  13 #define CONFIG_KM_DEF_NETDEV    "netdev=eth0\0"
  14
  15 /* an additionnal option is required for UBI as subpage access is
  16  * supported in u-boot */
  17 #define CONFIG_KM_UBI_PART_BOOT_OPTS            ",2048"
  18
  19 #define CONFIG_NAND_ECC_BCH
  20
  21 /* common KM defines */
  22 #include "keymile-common.h"
  23
  24 #define CONFIG_SYS_RAMBOOT
  25 #define CONFIG_RAMBOOT_PBL
  26 #define CONFIG_RAMBOOT_TEXT_BASE        CONFIG_SYS_TEXT_BASE
  27 #define CONFIG_RESET_VECTOR_ADDRESS     0xfffffffc
  28 #define CONFIG_SYS_FSL_PBL_PBI board/keymile/kmp204x/pbi.cfg
  29 #define CONFIG_SYS_FSL_PBL_RCW board/keymile/kmp204x/rcw_kmp204x.cfg
  30
  31 /* High Level Configuration Options */
  32 #define CONFIG_BOOKE
  33 #define CONFIG_E500                     /* BOOKE e500 family */
  34 #define CONFIG_E500MC                   /* BOOKE e500mc family */
  35 #define CONFIG_SYS_BOOK3E_HV            /* Category E.HV supported */
  36 #define CONFIG_FSL_CORENET              /* Freescale CoreNet platform */
  37 #define CONFIG_MP                       /* support multiple processors */
  38
  39 #define CONFIG_SYS_FSL_CPC              /* Corenet Platform Cache */
  40 #define CONFIG_SYS_NUM_CPC              CONFIG_NUM_DDR_CONTROLLERS
  41 #define CONFIG_FSL_ELBC                 /* Has Enhanced localbus controller */
  42 #define CONFIG_PCIE1                    /* PCIE controller 1 */
  43 #define CONFIG_PCIE3                    /* PCIE controller 3 */
  44 #define CONFIG_FSL_PCI_INIT             /* Use common FSL init code */
  45 #define CONFIG_SYS_PCI_64BIT            /* enable 64-bit PCI resources */
  46
  47 #define CONFIG_SYS_DPAA_RMAN            /* RMan */
  48
  49 /* Environment in SPI Flash */
  50 #define CONFIG_SYS_EXTRA_ENV_RELOC
  51 #define CONFIG_ENV_IS_IN_SPI_FLASH
  52 #define CONFIG_ENV_SPI_BUS              0
  53 #define CONFIG_ENV_SPI_CS               0
  54 #define CONFIG_ENV_SPI_MAX_HZ           20000000
  55 #define CONFIG_ENV_SPI_MODE             0
  56 #define CONFIG_ENV_OFFSET               0x100000        /* 1MB for u-boot */
  57 #define CONFIG_ENV_SIZE                 0x004000        /* 16K env */
  58 #define CONFIG_ENV_SECT_SIZE            0x010000
  59 #define CONFIG_ENV_OFFSET_REDUND        0x110000
  60 #define CONFIG_ENV_TOTAL_SIZE           0x020000
  61
  62 #define CONFIG_SYS_REDUNDAND_ENVIRONMENT
  63
  64 #ifndef __ASSEMBLY__
  65 unsigned long get_board_sys_clk(unsigned long dummy);
  66 #endif
  67 #define CONFIG_SYS_CLK_FREQ     get_board_sys_clk(0)
  68
  69 /*
  70  * These can be toggled for performance analysis, otherwise use default.
  71  */
  72 #define CONFIG_SYS_CACHE_STASHING
  73 #define CONFIG_BACKSIDE_L2_CACHE
  74 #define CONFIG_SYS_INIT_L2CSR0          L2CSR0_L2E
  75 #define CONFIG_BTB                      /* toggle branch predition */
  76
  77 #define CONFIG_ENABLE_36BIT_PHYS
  78
  79 #define CONFIG_ADDR_MAP
  80 #define CONFIG_SYS_NUM_ADDR_MAP         64      /* number of TLB1 entries */
  81
  82 #define CONFIG_POST CONFIG_SYS_POST_MEM_REGIONS /* POST memory regions test */
  83
  84 /*
  85  *  Config the L3 Cache as L3 SRAM
  86  */
  87 #define CONFIG_SYS_INIT_L3_ADDR         CONFIG_RAMBOOT_TEXT_BASE
  88 #define CONFIG_SYS_INIT_L3_ADDR_PHYS    (0xf00000000ull | \
  89                 CONFIG_RAMBOOT_TEXT_BASE)
  90 #define CONFIG_SYS_L3_SIZE              (1024 << 10)
  91 #define CONFIG_SYS_INIT_L3_END (CONFIG_SYS_INIT_L3_ADDR + CONFIG_SYS_L3_SIZE)
  92
  93 #define CONFIG_SYS_DCSRBAR              0xf0000000
  94 #define CONFIG_SYS_DCSRBAR_PHYS         0xf00000000ull
  95
  96 /*
  97  * DDR Setup
  98  */
  99 #define CONFIG_VERY_BIG_RAM
 100 #define CONFIG_SYS_DDR_SDRAM_BASE       0x00000000
 101 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE
 102
 103 #define CONFIG_DIMM_SLOTS_PER_CTLR      1
 104 #define CONFIG_CHIP_SELECTS_PER_CTRL    (4 * CONFIG_DIMM_SLOTS_PER_CTLR)
 105
 106 #define CONFIG_DDR_SPD
 107 #define CONFIG_SYS_FSL_DDR3
 108 #define CONFIG_FSL_DDR_INTERACTIVE
 109
 110 #define CONFIG_SYS_SPD_BUS_NUM  0
 111 #define SPD_EEPROM_ADDRESS      0x54
 112 #define CONFIG_SYS_SDRAM_SIZE   4096    /* for fixed parameter use */
 113
 114 #define CONFIG_SYS_LOAD_ADDR    0x100000        /* default load address */
 115 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN  2
 116
 117 /******************************************************************************
 118  * (PRAM usage)
 119  * ... -------------------------------------------------------
 120  * ... |ROOTFSSIZE | PNVRAM |PHRAM |RESERVED_PRAM | END_OF_RAM
 121  * ... |<------------------- pram -------------------------->|
 122  * ... -------------------------------------------------------
 123  * @END_OF_RAM:
 124  * @CONFIG_KM_RESERVED_PRAM: reserved pram for special purpose
 125  * @CONFIG_KM_PHRAM: address for /var
 126  * @CONFIG_KM_PNVRAM: address for PNVRAM (for the application)
 127  * @CONFIG_KM_ROOTFSSIZE: address for rootfilesystem in RAM
 128  */
 129
 130 /* size of rootfs in RAM */
 131 #define CONFIG_KM_ROOTFSSIZE    0x0
 132 /* pseudo-non volatile RAM [hex] */
 133 #define CONFIG_KM_PNVRAM        0x80000
 134 /* physical RAM MTD size [hex] */
 135 #define CONFIG_KM_PHRAM         0x100000
 136 /* reserved pram area at the end of memory [hex]
 137  * u-boot reserves some memory for the MP boot page */
 138 #define CONFIG_KM_RESERVED_PRAM 0x1000
 139 /* set the default PRAM value to at least PNVRAM + PHRAM when pram env variable
 140  * is not valid yet, which is the case for when u-boot copies itself to RAM */
 141 #define CONFIG_PRAM             ((CONFIG_KM_PNVRAM + CONFIG_KM_PHRAM)>>10)
 142
 143 #define CONFIG_KM_CRAMFS_ADDR   0x2000000
 144 #define CONFIG_KM_KERNEL_ADDR   0x1000000       /* max kernel size 15.5Mbytes */
 145 #define CONFIG_KM_FDT_ADDR      0x1F80000       /* max dtb    size  0.5Mbytes */
 146
 147 /*
 148  * Local Bus Definitions
 149  */
 150
 151 /* Set the local bus clock 1/8 of plat clk, 2 clk delay LALE */
 152 #define CONFIG_SYS_LBC_LCRR             (LCRR_CLKDIV_8 | LCRR_EADC_2)
 153
 154 /* Nand Flash */
 155 #define CONFIG_NAND_FSL_ELBC
 156 #define CONFIG_SYS_NAND_BASE            0xffa00000
 157 #define CONFIG_SYS_NAND_BASE_PHYS       0xfffa00000ull
 158
 159 #define CONFIG_SYS_NAND_BASE_LIST     {CONFIG_SYS_NAND_BASE}
 160 #define CONFIG_SYS_MAX_NAND_DEVICE      1
 161 #define CONFIG_CMD_NAND
 162 #define CONFIG_SYS_NAND_BLOCK_SIZE    (128 * 1024)
 163
 164 #define CONFIG_BCH
 165
 166 /* NAND flash config */
 167 #define CONFIG_SYS_NAND_BR_PRELIM  (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
 168                                | BR_PS_8               /* Port Size = 8 bit */ \
 169                                | BR_MS_FCM             /* MSEL = FCM */ \
 170                                | BR_V)                 /* valid */
 171
 172 #define CONFIG_SYS_NAND_OR_PRELIM  (OR_AM_256KB       /* length 256K */ \
 173                                | OR_FCM_BCTLD   /* LBCTL not ass */     \
 174                                | OR_FCM_SCY_1   /* 1 clk wait cycle */  \
 175                                | OR_FCM_RST     /* 1 clk read setup */  \
 176                                | OR_FCM_PGS     /* Large page size */   \
 177                                | OR_FCM_CST)    /* 0.25 command setup */
 178
 179 #define CONFIG_SYS_BR0_PRELIM  CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */
 180 #define CONFIG_SYS_OR0_PRELIM  CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */
 181
 182 /* QRIO FPGA */
 183 #define CONFIG_SYS_QRIO_BASE            0xfb000000
 184 #define CONFIG_SYS_QRIO_BASE_PHYS       0xffb000000ull
 185
 186 #define CONFIG_SYS_QRIO_BR_PRELIM  (BR_PHYS_ADDR(CONFIG_SYS_QRIO_BASE_PHYS) \
 187                                 | BR_PS_8       /* Port Size 8 bits */ \
 188                                 | BR_DECC_OFF   /* no error corr */ \
 189                                 | BR_MS_GPCM    /* MSEL = GPCM */ \
 190                                 | BR_V)         /* valid */
 191
 192 #define CONFIG_SYS_QRIO_OR_PRELIM  (OR_AM_64KB  /* length 64K */ \
 193                                 | OR_GPCM_BCTLD /* no LCTL assert */ \
 194                                 | OR_GPCM_ACS_DIV4 /* LCS 1/4 clk after */ \
 195                                 | OR_GPCM_SCY_2 /* 2 clk wait cycles */ \
 196                                 | OR_GPCM_TRLX /* relaxed tmgs */ \
 197                                 | OR_GPCM_EAD) /* extra bus clk cycles */
 198
 199 #define CONFIG_SYS_BR1_PRELIM  CONFIG_SYS_QRIO_BR_PRELIM /* QRIO Base Address */
 200 #define CONFIG_SYS_OR1_PRELIM  CONFIG_SYS_QRIO_OR_PRELIM /* QRIO Options */
 201
 202 /* bootcounter in QRIO */
 203 #define CONFIG_BOOTCOUNT_LIMIT
 204 #define CONFIG_SYS_BOOTCOUNT_ADDR       (CONFIG_SYS_QRIO_BASE + 0x20)
 205
 206 #define CONFIG_BOARD_EARLY_INIT_F
 207 #define CONFIG_BOARD_EARLY_INIT_R       /* call board_early_init_r function */
 208 #define CONFIG_MISC_INIT_F
 209 #define CONFIG_MISC_INIT_R
 210 #define CONFIG_LAST_STAGE_INIT
 211
 212 #define CONFIG_HWCONFIG
 213
 214 /* define to use L1 as initial stack */
 215 #define CONFIG_L1_INIT_RAM
 216 #define CONFIG_SYS_INIT_RAM_LOCK
 217 #define CONFIG_SYS_INIT_RAM_ADDR        0xffd00000      /* Initial L1 address */
 218 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf
 219 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR
 220 /* The assembler doesn't like typecast */
 221 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
 222         ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
 223           CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
 224 #define CONFIG_SYS_INIT_RAM_SIZE        0x00004000
 225
 226 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - \
 227                                         GENERATED_GBL_DATA_SIZE)
 228 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 229
 230 #define CONFIG_SYS_MONITOR_BASE         CONFIG_SYS_TEXT_BASE
 231 #define CONFIG_SYS_MONITOR_LEN          (768 * 1024)
 232 #define CONFIG_SYS_MALLOC_LEN           (1024 * 1024)
 233
 234 /* Serial Port - controlled on board with jumper J8
 235  * open - index 2
 236  * shorted - index 1
 237  */
 238 #define CONFIG_CONS_INDEX       1
 239 #define CONFIG_SYS_NS16550_SERIAL
 240 #define CONFIG_SYS_NS16550_REG_SIZE     1
 241 #define CONFIG_SYS_NS16550_CLK          (get_bus_freq(0)/2)
 242
 243 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500)
 244 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600)
 245 #define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500)
 246 #define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600)
 247
 248 #define CONFIG_KM_CONSOLE_TTY   "ttyS0"
 249
 250 /* I2C */
 251
 252 #define CONFIG_SYS_I2C
 253 #define CONFIG_SYS_I2C_INIT_BOARD
 254 #define CONFIG_SYS_I2C_SPEED            100000 /* deblocking */
 255 #define CONFIG_SYS_NUM_I2C_BUSES        3
 256 #define CONFIG_SYS_I2C_MAX_HOPS         1
 257 #define CONFIG_SYS_I2C_FSL              /* Use FSL I2C driver */
 258 #define CONFIG_I2C_MULTI_BUS
 259 #define CONFIG_I2C_CMD_TREE
 260 #define CONFIG_SYS_FSL_I2C_SPEED        400000
 261 #define CONFIG_SYS_FSL_I2C_SLAVE        0x7F
 262 #define CONFIG_SYS_FSL_I2C_OFFSET       0x118000
 263 #define CONFIG_SYS_I2C_BUSES    {       {0, {I2C_NULL_HOP} }, \
 264                                         {0, {{I2C_MUX_PCA9547, 0x70, 1 } } }, \
 265                                         {0, {{I2C_MUX_PCA9547, 0x70, 2 } } }, \
 266                                 }
 267 #ifndef __ASSEMBLY__
 268 void set_sda(int state);
 269 void set_scl(int state);
 270 int get_sda(void);
 271 int get_scl(void);
 272 #endif
 273
 274 #define CONFIG_KM_IVM_BUS               1       /* I2C1 (Mux-Port 1)*/
 275
 276 /*
 277  * eSPI - Enhanced SPI
 278  */
 279 #define CONFIG_SPI_FLASH_BAR    /* 4 byte-addressing */
 280 #define CONFIG_SF_DEFAULT_SPEED         20000000
 281 #define CONFIG_SF_DEFAULT_MODE          0
 282
 283 /*
 284  * General PCI
 285  * Memory space is mapped 1-1, but I/O space must start from 0.
 286  */
 287
 288 /* controller 1, direct to uli, tgtid 3, Base address 20000 */
 289 #define CONFIG_SYS_PCIE1_MEM_VIRT       0x80000000
 290 #define CONFIG_SYS_PCIE1_MEM_BUS        0xe0000000
 291 #define CONFIG_SYS_PCIE1_MEM_PHYS       0xc00000000ull
 292 #define CONFIG_SYS_PCIE1_MEM_SIZE       0x20000000      /* 512M */
 293 #define CONFIG_SYS_PCIE1_IO_VIRT        0xf8000000
 294 #define CONFIG_SYS_PCIE1_IO_BUS         0x00000000
 295 #define CONFIG_SYS_PCIE1_IO_PHYS        0xff8000000ull
 296 #define CONFIG_SYS_PCIE1_IO_SIZE        0x00010000      /* 64k */
 297
 298 /* controller 3, Slot 1, tgtid 1, Base address 202000 */
 299 #define CONFIG_SYS_PCIE3_MEM_VIRT       0xa0000000
 300 #define CONFIG_SYS_PCIE3_MEM_BUS        0xe0000000
 301 #define CONFIG_SYS_PCIE3_MEM_PHYS       0xc20000000ull
 302 #define CONFIG_SYS_PCIE3_MEM_SIZE       0x20000000      /* 512M */
 303 #define CONFIG_SYS_PCIE3_IO_VIRT        0xf8010000
 304 #define CONFIG_SYS_PCIE3_IO_BUS         0x00000000
 305 #define CONFIG_SYS_PCIE3_IO_PHYS        0xff8010000ull
 306 #define CONFIG_SYS_PCIE3_IO_SIZE        0x00010000      /* 64k */
 307
 308 /* Qman/Bman */
 309 #define CONFIG_SYS_DPAA_QBMAN           /* Support Q/Bman */
 310 #define CONFIG_SYS_BMAN_NUM_PORTALS     10
 311 #define CONFIG_SYS_BMAN_MEM_BASE        0xf4000000
 312 #define CONFIG_SYS_BMAN_MEM_PHYS        0xff4000000ull
 313 #define CONFIG_SYS_BMAN_MEM_SIZE        0x00200000
 314 #define CONFIG_SYS_BMAN_SP_CENA_SIZE    0x4000
 315 #define CONFIG_SYS_BMAN_SP_CINH_SIZE    0x1000
 316 #define CONFIG_SYS_BMAN_CENA_BASE       CONFIG_SYS_BMAN_MEM_BASE
 317 #define CONFIG_SYS_BMAN_CENA_SIZE       (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
 318 #define CONFIG_SYS_BMAN_CINH_BASE       (CONFIG_SYS_BMAN_MEM_BASE + \
 319                                         CONFIG_SYS_BMAN_CENA_SIZE)
 320 #define CONFIG_SYS_BMAN_CINH_SIZE       (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
 321 #define CONFIG_SYS_BMAN_SWP_ISDR_REG    0xE08
 322 #define CONFIG_SYS_QMAN_NUM_PORTALS     10
 323 #define CONFIG_SYS_QMAN_MEM_BASE        0xf4200000
 324 #define CONFIG_SYS_QMAN_MEM_PHYS        0xff4200000ull
 325 #define CONFIG_SYS_QMAN_MEM_SIZE        0x00200000
 326 #define CONFIG_SYS_QMAN_SP_CENA_SIZE    0x4000
 327 #define CONFIG_SYS_QMAN_SP_CINH_SIZE    0x1000
 328 #define CONFIG_SYS_QMAN_CENA_BASE       CONFIG_SYS_QMAN_MEM_BASE
 329 #define CONFIG_SYS_QMAN_CENA_SIZE       (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
 330 #define CONFIG_SYS_QMAN_CINH_BASE       (CONFIG_SYS_QMAN_MEM_BASE + \
 331                                         CONFIG_SYS_QMAN_CENA_SIZE)
 332 #define CONFIG_SYS_QMAN_CINH_SIZE       (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
 333 #define CONFIG_SYS_QMAN_SWP_ISDR_REG    0xE08
 334
 335 #define CONFIG_SYS_DPAA_FMAN
 336 #define CONFIG_SYS_DPAA_PME
 337 /* Default address of microcode for the Linux Fman driver
 338  * env is stored at 0x100000, sector size is 0x10000, x2 (redundant)
 339  * ucode is stored after env, so we got 0x120000.
 340  */
 341 #define CONFIG_SYS_QE_FW_IN_SPIFLASH
 342 #define CONFIG_SYS_FMAN_FW_ADDR 0x120000
 343 #define CONFIG_SYS_QE_FMAN_FW_LENGTH    0x10000
 344 #define CONFIG_SYS_FDT_PAD              (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
 345
 346 #define CONFIG_FMAN_ENET
 347 #define CONFIG_PHYLIB_10G
 348 #define CONFIG_PHY_MARVELL              /* there is a marvell phy */
 349
 350 #define CONFIG_PCI_INDIRECT_BRIDGE
 351
 352 #define CONFIG_PCI_SCAN_SHOW            /* show pci devices on startup */
 353 #define CONFIG_DOS_PARTITION
 354
 355 /* RGMII (FM1@DTESC5) is used as debug itf, it's the only one configured */
 356 #define CONFIG_SYS_FM1_DTSEC5_PHY_ADDR  0x11
 357 #define CONFIG_SYS_TBIPA_VALUE  8
 358 #define CONFIG_PHYLIB           /* recommended PHY management */
 359 #define CONFIG_ETHPRIME         "FM1@DTSEC5"
 360 #define CONFIG_PHY_GIGE         /* Include GbE speed/duplex detection */
 361
 362 /*
 363  * Environment
 364  */
 365 #define CONFIG_LOADS_ECHO               /* echo on for serial download */
 366 #define CONFIG_SYS_LOADS_BAUD_CHANGE    /* allow baudrate change */
 367
 368 /*
 369  * Hardware Watchdog
 370  */
 371 #define CONFIG_WATCHDOG                 /* enable CPU watchdog */
 372 #define CONFIG_WATCHDOG_PRESC 34        /* wdog prescaler 2^(64-34) (~10min) */
 373 #define CONFIG_WATCHDOG_RC WRC_CHIP     /* reset chip on watchdog event */
 374
 375
 376 /*
 377  * additionnal command line configuration.
 378  */
 379 #define CONFIG_CMD_PCI
 380 #define CONFIG_CMD_ERRATA
 381
 382 /* we don't need flash support */
 383 #define CONFIG_SYS_NO_FLASH
 384 #undef CONFIG_FLASH_CFI_MTD
 385 #undef CONFIG_JFFS2_CMDLINE
 386
 387 /*
 388  * For booting Linux, the board info and command line data
 389  * have to be in the first 64 MB of memory, since this is
 390  * the maximum mapped by the Linux kernel during initialization.
 391  */
 392 #define CONFIG_SYS_BOOTMAPSZ    (64 << 20)      /* Initial Memory for Linux */
 393 #define CONFIG_SYS_BOOTM_LEN    (64 << 20)      /* Increase max gunzip size */
 394
 395 #ifdef CONFIG_CMD_KGDB
 396 #define CONFIG_KGDB_BAUDRATE    230400  /* speed to run kgdb serial port */
 397 #endif
 398
 399 #define __USB_PHY_TYPE  utmi
 400 #define CONFIG_USB_EHCI_FSL
 401
 402 /*
 403  * Environment Configuration
 404  */
 405 #define CONFIG_ENV_OVERWRITE
 406 #ifndef CONFIG_KM_DEF_ENV               /* if not set by keymile-common.h */
 407 #define CONFIG_KM_DEF_ENV "km-common=empty\0"
 408 #endif
 409
 410 #ifndef MTDIDS_DEFAULT
 411 # define MTDIDS_DEFAULT         "nand0=fsl_elbc_nand"
 412 #endif /* MTDIDS_DEFAULT */
 413
 414 #ifndef MTDPARTS_DEFAULT
 415 # define MTDPARTS_DEFAULT       "mtdparts="                     \
 416         "fsl_elbc_nand:"                                                \
 417                 "-(" CONFIG_KM_UBI_PARTITION_NAME_BOOT ");"
 418 #endif /* MTDPARTS_DEFAULT */
 419
 420 /* architecture specific default bootargs */
 421 #define CONFIG_KM_DEF_BOOT_ARGS_CPU             ""
 422
 423 /* FIXME: FDT_ADDR is unspecified */
 424 #define CONFIG_KM_DEF_ENV_CPU                                           \
 425         "boot=bootm ${load_addr_r} - ${fdt_addr_r}\0"                   \
 426         "cramfsloadfdt="                                                \
 427                 "cramfsload ${fdt_addr_r} "                             \
 428                 "fdt_0x${IVM_BoardId}_0x${IVM_HWKey}.dtb\0"             \
 429         "fdt_addr_r=" __stringify(CONFIG_KM_FDT_ADDR) "\0"              \
 430         "u-boot="__stringify(CONFIG_HOSTNAME) "/u-boot.pbl\0"           \
 431         "update="                                                       \
 432                 "sf probe 0;sf erase 0 +${filesize};"                   \
 433                 "sf write ${load_addr_r} 0 ${filesize};\0"              \
 434         "set_fdthigh=true\0"                                            \
 435         "checkfdt=true\0"                                               \
 436         ""
 437
 438 #define CONFIG_HW_ENV_SETTINGS                                          \
 439         "hwconfig=fsl_ddr:ctlr_intlv=cacheline\0"                       \
 440         "usb_phy_type=" __stringify(__USB_PHY_TYPE) "\0"                \
 441         "usb_dr_mode=host\0"
 442
 443 #define CONFIG_KM_NEW_ENV                                               \
 444         "newenv=sf probe 0;"                                            \
 445                 "sf erase " __stringify(CONFIG_ENV_OFFSET) " "          \
 446                 __stringify(CONFIG_ENV_TOTAL_SIZE)"\0"
 447
 448 /* ppc_82xx is the equivalent to ppc_6xx, the generic ppc toolchain */
 449 #ifndef CONFIG_KM_DEF_ARCH
 450 #define CONFIG_KM_DEF_ARCH      "arch=ppc_82xx\0"
 451 #endif
 452
 453 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
 454         CONFIG_KM_DEF_ENV                                               \
 455         CONFIG_KM_DEF_ARCH                                              \
 456         CONFIG_KM_NEW_ENV                                               \
 457         CONFIG_HW_ENV_SETTINGS                                          \
 458         "EEprom_ivm=pca9547:70:9\0"                                     \
 459         ""
 460
 461 #endif /* _CONFIG_KMP204X_H */