include/configs/j721e_evm.h

   1 /* SPDX-License-Identifier: GPL-2.0+ */
   2 /*
   3  * Configuration header file for K3 J721E EVM
   4  *
   5  * Copyright (C) 2018-2020 Texas Instruments Incorporated - https://www.ti.com/
   6  *      Lokesh Vutla <lokeshvutla@ti.com>
   7  */
   8
   9 #ifndef __CONFIG_J721E_EVM_H
  10 #define __CONFIG_J721E_EVM_H
  11
  12 #include <linux/sizes.h>
  13 #include <environment/ti/mmc.h>
  14 #include <environment/ti/k3_rproc.h>
  15 #include <environment/ti/ufs.h>
  16 #include <environment/ti/k3_dfu.h>
  17
  18 /* DDR Configuration */
  19 #define CONFIG_SYS_SDRAM_BASE1          0x880000000
  20
  21 /* SPL Loader Configuration */
  22 #if defined(CONFIG_TARGET_J721E_A72_EVM) || defined(CONFIG_TARGET_J7200_A72_EVM)
  23 #define CONFIG_SYS_INIT_SP_ADDR         (CONFIG_SPL_TEXT_BASE + SZ_4M)
  24 #define CONFIG_SYS_UBOOT_BASE           0x50280000
  25 /* Image load address in RAM for DFU boot*/
  26 #else
  27 #define CONFIG_SYS_UBOOT_BASE           0x50080000
  28 /*
  29  * Maximum size in memory allocated to the SPL BSS. Keep it as tight as
  30  * possible (to allow the build to go through), as this directly affects
  31  * our memory footprint. The less we use for BSS the more we have available
  32  * for everything else.
  33  */
  34 #define CONFIG_SPL_BSS_MAX_SIZE         0xA000
  35 /*
  36  * Link BSS to be within SPL in a dedicated region located near the top of
  37  * the MCU SRAM, this way making it available also before relocation. Note
  38  * that we are not using the actual top of the MCU SRAM as there is a memory
  39  * location filled in by the boot ROM that we want to read out without any
  40  * interference from the C context.
  41  */
  42 #define CONFIG_SPL_BSS_START_ADDR       (CONFIG_SYS_K3_BOOT_PARAM_TABLE_INDEX -\
  43                                          CONFIG_SPL_BSS_MAX_SIZE)
  44 /* Set the stack right below the SPL BSS section */
  45 #define CONFIG_SYS_INIT_SP_ADDR         CONFIG_SPL_BSS_START_ADDR
  46 /* Configure R5 SPL post-relocation malloc pool in DDR */
  47 #define CONFIG_SYS_SPL_MALLOC_START     0x84000000
  48 #define CONFIG_SYS_SPL_MALLOC_SIZE      SZ_16M
  49 /* Image load address in RAM for DFU boot*/
  50 #endif
  51
  52 #define CONFIG_SYS_BOOTM_LEN            SZ_64M
  53
  54 /* HyperFlash related configuration */
  55
  56 /* U-Boot general configuration */
  57 #define EXTRA_ENV_J721E_BOARD_SETTINGS                                  \
  58         "default_device_tree=" CONFIG_DEFAULT_DEVICE_TREE ".dtb\0"      \
  59         "findfdt="                                                      \
  60                 "setenv name_fdt ${default_device_tree};"               \
  61                 "if test $board_name = j721e; then "                    \
  62                         "setenv name_fdt k3-j721e-common-proc-board.dtb; fi;" \
  63                 "if test $board_name = j721e-eaik || test $board_name = j721e-sk; then "                \
  64                         "setenv name_fdt k3-j721e-sk.dtb; fi;"  \
  65                 "setenv fdtfile ${name_fdt}\0"                          \
  66         "name_kern=Image\0"                                             \
  67         "console=ttyS2,115200n8\0"                                      \
  68         "args_all=setenv optargs earlycon=ns16550a,mmio32,0x02800000 "  \
  69                 "${mtdparts}\0"                                         \
  70         "run_kern=booti ${loadaddr} ${rd_spec} ${fdtaddr}\0"
  71
  72 #define PARTS_DEFAULT \
  73         /* Linux partitions */ \
  74         "uuid_disk=${uuid_gpt_disk};" \
  75         "name=rootfs,start=0,size=-,uuid=${uuid_gpt_rootfs}\0"
  76
  77 #ifdef CONFIG_SYS_K3_SPL_ATF
  78 #if defined(CONFIG_TARGET_J721E_R5_EVM)
  79 #define EXTRA_ENV_R5_SPL_RPROC_FW_ARGS_MMC                              \
  80         "addr_mcur5f0_0load=0x89000000\0"                               \
  81         "name_mcur5f0_0fw=/lib/firmware/j7-mcu-r5f0_0-fw\0"
  82 #elif defined(CONFIG_TARGET_J7200_R5_EVM)
  83 #define EXTRA_ENV_R5_SPL_RPROC_FW_ARGS_MMC                              \
  84         "addr_mcur5f0_0load=0x89000000\0"                               \
  85         "name_mcur5f0_0fw=/lib/firmware/j7200-mcu-r5f0_0-fw\0"
  86 #endif /* CONFIG_TARGET_J721E_R5_EVM */
  87 #else
  88 #define EXTRA_ENV_R5_SPL_RPROC_FW_ARGS_MMC ""
  89 #endif /* CONFIG_SYS_K3_SPL_ATF */
  90
  91 /* U-Boot MMC-specific configuration */
  92 #define EXTRA_ENV_J721E_BOARD_SETTINGS_MMC                              \
  93         "boot=mmc\0"                                                    \
  94         "mmcdev=1\0"                                                    \
  95         "bootpart=1:2\0"                                                \
  96         "bootdir=/boot\0"                                               \
  97         EXTRA_ENV_R5_SPL_RPROC_FW_ARGS_MMC                              \
  98         "rd_spec=-\0"                                                   \
  99         "init_mmc=run args_all args_mmc\0"                              \
 100         "get_fdt_mmc=load mmc ${bootpart} ${fdtaddr} ${bootdir}/${name_fdt}\0" \
 101         "get_overlay_mmc="                                              \
 102                 "fdt address ${fdtaddr};"                               \
 103                 "fdt resize 0x100000;"                                  \
 104                 "for overlay in $name_overlays;"                        \
 105                 "do;"                                                   \
 106                 "load mmc ${bootpart} ${dtboaddr} ${bootdir}/${overlay} && "    \
 107                 "fdt apply ${dtboaddr};"                                \
 108                 "done;\0"                                               \
 109         "partitions=" PARTS_DEFAULT                                     \
 110         "get_kern_mmc=load mmc ${bootpart} ${loadaddr} "                \
 111                 "${bootdir}/${name_kern}\0"                             \
 112         "get_fit_mmc=load mmc ${bootpart} ${addr_fit} "                 \
 113                 "${bootdir}/${name_fit}\0"                              \
 114         "partitions=" PARTS_DEFAULT
 115
 116 /* Set the default list of remote processors to boot */
 117 #if defined(CONFIG_TARGET_J7200_A72_EVM)
 118 #define EXTRA_ENV_CONFIG_MAIN_CPSW0_QSGMII_PHY                          \
 119         "do_main_cpsw0_qsgmii_phyinit=1\0"                              \
 120         "init_main_cpsw0_qsgmii_phy=gpio set gpio@22_17;"               \
 121                  "gpio clear gpio@22_16\0"                              \
 122         "main_cpsw0_qsgmii_phyinit="                                    \
 123         "if test ${do_main_cpsw0_qsgmii_phyinit} -eq 1 && test ${dorprocboot} -eq 1 && " \
 124                         "test ${boot} = mmc; then "                     \
 125                 "run init_main_cpsw0_qsgmii_phy;"                       \
 126         "fi;\0"
 127 #ifdef DEFAULT_RPROCS
 128 #undef DEFAULT_RPROCS
 129 #endif
 130 #elif defined(CONFIG_TARGET_J721E_A72_EVM)
 131 #define EXTRA_ENV_CONFIG_MAIN_CPSW0_QSGMII_PHY                          \
 132         "init_main_cpsw0_qsgmii_phy=gpio set gpio@22_17;"               \
 133                  "gpio clear gpio@22_16\0"                              \
 134         "main_cpsw0_qsgmii_phyinit="                                    \
 135         "if test $board_name = J721EX-PM1-SOM || test $board_name = J721EX-PM2-SOM " \
 136         "|| test $board_name = j721e; then " \
 137         "do_main_cpsw0_qsgmii_phyinit=1; else "                 \
 138         "do_main_cpsw0_qsgmii_phyinit=0; fi;"                   \
 139         "if test ${do_main_cpsw0_qsgmii_phyinit} -eq 1 && test ${dorprocboot} -eq 1 && " \
 140                         "test ${boot} = mmc; then "                     \
 141                 "run init_main_cpsw0_qsgmii_phy;"                       \
 142         "fi;\0"
 143 #ifdef DEFAULT_RPROCS
 144 #undef DEFAULT_RPROCS
 145 #endif
 146 #endif
 147
 148 #ifdef CONFIG_TARGET_J721E_A72_EVM
 149 #define DEFAULT_RPROCS  ""                                              \
 150                 "2 /lib/firmware/j7-main-r5f0_0-fw "                    \
 151                 "3 /lib/firmware/j7-main-r5f0_1-fw "                    \
 152                 "4 /lib/firmware/j7-main-r5f1_0-fw "                    \
 153                 "5 /lib/firmware/j7-main-r5f1_1-fw "                    \
 154                 "6 /lib/firmware/j7-c66_0-fw "                          \
 155                 "7 /lib/firmware/j7-c66_1-fw "                          \
 156                 "8 /lib/firmware/j7-c71_0-fw "
 157 #endif /* CONFIG_TARGET_J721E_A72_EVM */
 158
 159 #ifdef CONFIG_TARGET_J7200_A72_EVM
 160 #define DEFAULT_RPROCS ""                                               \
 161                 "2 /lib/firmware/j7200-main-r5f0_0-fw "                 \
 162                 "3 /lib/firmware/j7200-main-r5f0_1-fw "
 163 #endif /* CONFIG_TARGET_J7200_A72_EVM */
 164
 165 #ifndef EXTRA_ENV_CONFIG_MAIN_CPSW0_QSGMII_PHY
 166 #define EXTRA_ENV_CONFIG_MAIN_CPSW0_QSGMII_PHY
 167 #endif
 168
 169 #define EXTRA_ENV_DFUARGS \
 170         DFU_ALT_INFO_MMC \
 171         DFU_ALT_INFO_EMMC \
 172         DFU_ALT_INFO_RAM \
 173         DFU_ALT_INFO_OSPI
 174
 175 #if defined(CONFIG_TARGET_J721E_A72_EVM) || defined(CONFIG_TARGET_J7200_A72_EVM)
 176 #define EXTRA_ENV_J721E_BOARD_SETTINGS_MTD                              \
 177         "mtdids=" CONFIG_MTDIDS_DEFAULT "\0"                            \
 178         "mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0"
 179 #else
 180 #define EXTRA_ENV_J721E_BOARD_SETTINGS_MTD
 181 #endif
 182
 183 #if CONFIG_IS_ENABLED(CMD_PXE)
 184 # define BOOT_TARGET_PXE(func) func(PXE, pxe, na)
 185 #else
 186 # define BOOT_TARGET_PXE(func)
 187 #endif
 188
 189 #if CONFIG_IS_ENABLED(CMD_DHCP)
 190 # define BOOT_TARGET_DHCP(func) func(DHCP, dhcp, na)
 191 #else
 192 # define BOOT_TARGET_DHCP(func)
 193 #endif
 194
 195 #define BOOT_TARGET_DEVICES(func) \
 196         func(MMC, mmc, 1) \
 197         func(MMC, mmc, 0) \
 198         BOOT_TARGET_PXE(func) \
 199         BOOT_TARGET_DHCP(func)
 200
 201 #include <config_distro_bootcmd.h>
 202
 203 /* Incorporate settings into the U-Boot environment */
 204 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
 205         DEFAULT_LINUX_BOOT_ENV                                          \
 206         DEFAULT_MMC_TI_ARGS                                             \
 207         DEFAULT_FIT_TI_ARGS                                             \
 208         EXTRA_ENV_J721E_BOARD_SETTINGS                                  \
 209         EXTRA_ENV_J721E_BOARD_SETTINGS_MMC                              \
 210         EXTRA_ENV_RPROC_SETTINGS                                        \
 211         EXTRA_ENV_DFUARGS                                               \
 212         DEFAULT_UFS_TI_ARGS                                             \
 213         EXTRA_ENV_J721E_BOARD_SETTINGS_MTD                              \
 214         EXTRA_ENV_CONFIG_MAIN_CPSW0_QSGMII_PHY                          \
 215         BOOTENV
 216
 217 /* Now for the remaining common defines */
 218 #include <configs/ti_armv7_common.h>
 219
 220 /* MMC ENV related defines */
 221
 222 #endif /* __CONFIG_J721E_EVM_H */