include/configs/imx8mq_evk.h

   1 /* SPDX-License-Identifier: GPL-2.0+ */
   2 /*
   3  * Copyright 2018 NXP
   4  */
   5
   6 #ifndef __IMX8M_EVK_H
   7 #define __IMX8M_EVK_H
   8
   9 #include <linux/sizes.h>
  10 #include <asm/arch/imx-regs.h>
  11
  12 #ifdef CONFIG_SECURE_BOOT
  13 #define CONFIG_CSF_SIZE                 0x2000 /* 8K region */
  14 #endif
  15
  16 #define CONFIG_SPL_MAX_SIZE             (124 * 1024)
  17 #define CONFIG_SYS_MONITOR_LEN          (512 * 1024)
  18 #define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR
  19 #define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300
  20 #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION      1
  21
  22 #ifdef CONFIG_SPL_BUILD
  23 /*#define CONFIG_ENABLE_DDR_TRAINING_DEBUG*/
  24 #define CONFIG_SPL_WATCHDOG_SUPPORT
  25 #define CONFIG_SPL_DRIVERS_MISC_SUPPORT
  26 #define CONFIG_SPL_POWER_SUPPORT
  27 #define CONFIG_SPL_I2C_SUPPORT
  28 #define CONFIG_SPL_LDSCRIPT             "arch/arm/cpu/armv8/u-boot-spl.lds"
  29 #define CONFIG_SPL_STACK                0x187FF0
  30 #define CONFIG_SPL_LIBCOMMON_SUPPORT
  31 #define CONFIG_SPL_LIBGENERIC_SUPPORT
  32 #define CONFIG_SPL_GPIO_SUPPORT
  33 #define CONFIG_SPL_MMC_SUPPORT
  34 #define CONFIG_SPL_BSS_START_ADDR      0x00180000
  35 #define CONFIG_SPL_BSS_MAX_SIZE        0x2000   /* 8 KB */
  36 #define CONFIG_SYS_SPL_MALLOC_START    0x42200000
  37 #define CONFIG_SYS_SPL_MALLOC_SIZE    0x80000   /* 512 KB */
  38 #define CONFIG_SYS_SPL_PTE_RAM_BASE    0x41580000
  39
  40 /* malloc f used before GD_FLG_FULL_MALLOC_INIT set */
  41 #define CONFIG_MALLOC_F_ADDR            0x182000
  42 /* For RAW image gives a error info not panic */
  43 #define CONFIG_SPL_ABORT_ON_RAW_IMAGE
  44
  45 #undef CONFIG_DM_MMC
  46 #undef CONFIG_DM_PMIC
  47 #undef CONFIG_DM_PMIC_PFUZE100
  48
  49 #define CONFIG_SYS_I2C
  50 #define CONFIG_SYS_I2C_MXC_I2C1         /* enable I2C bus 1 */
  51 #define CONFIG_SYS_I2C_MXC_I2C2         /* enable I2C bus 2 */
  52 #define CONFIG_SYS_I2C_MXC_I2C3         /* enable I2C bus 3 */
  53
  54 #define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
  55
  56 #define CONFIG_POWER
  57 #define CONFIG_POWER_I2C
  58 #define CONFIG_POWER_PFUZE100
  59 #define CONFIG_POWER_PFUZE100_I2C_ADDR 0x08
  60 #endif
  61
  62 #define CONFIG_REMAKE_ELF
  63
  64 #define CONFIG_BOARD_EARLY_INIT_F
  65 #define CONFIG_BOARD_LATE_INIT
  66
  67 #undef CONFIG_CMD_EXPORTENV
  68 #undef CONFIG_CMD_IMPORTENV
  69 #undef CONFIG_CMD_IMLS
  70
  71 #undef CONFIG_CMD_CRC32
  72 #undef CONFIG_BOOTM_NETBSD
  73
  74 /* ENET Config */
  75 /* ENET1 */
  76 #if defined(CONFIG_CMD_NET)
  77 #define CONFIG_CMD_PING
  78 #define CONFIG_CMD_DHCP
  79 #define CONFIG_CMD_MII
  80 #define CONFIG_MII
  81 #define CONFIG_ETHPRIME                 "FEC"
  82
  83 #define CONFIG_FEC_MXC
  84 #define CONFIG_FEC_XCV_TYPE             RGMII
  85 #define CONFIG_FEC_MXC_PHYADDR          0
  86 #define FEC_QUIRK_ENET_MAC
  87
  88 #define CONFIG_PHY_GIGE
  89 #define IMX_FEC_BASE                    0x30BE0000
  90
  91 #define CONFIG_PHYLIB
  92 #define CONFIG_PHY_ATHEROS
  93 #endif
  94
  95 #define CONFIG_MFG_ENV_SETTINGS \
  96         "mfgtool_args=setenv bootargs console=${console},${baudrate} " \
  97                 "rdinit=/linuxrc " \
  98                 "g_mass_storage.stall=0 g_mass_storage.removable=1 " \
  99                 "g_mass_storage.idVendor=0x066F g_mass_storage.idProduct=0x37FF "\
 100                 "g_mass_storage.iSerialNumber=\"\" "\
 101                 "clk_ignore_unused "\
 102                 "\0" \
 103         "initrd_addr=0x43800000\0" \
 104         "initrd_high=0xffffffff\0" \
 105         "bootcmd_mfg=run mfgtool_args;booti ${loadaddr} ${initrd_addr} ${fdt_addr};\0" \
 106 /* Initial environment variables */
 107 #define CONFIG_EXTRA_ENV_SETTINGS               \
 108         CONFIG_MFG_ENV_SETTINGS \
 109         "script=boot.scr\0" \
 110         "image=Image\0" \
 111         "console=ttymxc0,115200 earlycon=ec_imx6q,0x30860000,115200\0" \
 112         "fdt_addr=0x43000000\0"                 \
 113         "fdt_high=0xffffffffffffffff\0"         \
 114         "boot_fdt=try\0" \
 115         "fdt_file=fsl-imx8mq-evk.dtb\0" \
 116         "initrd_addr=0x43800000\0"              \
 117         "initrd_high=0xffffffffffffffff\0" \
 118         "mmcdev="__stringify(CONFIG_SYS_MMC_ENV_DEV)"\0" \
 119         "mmcpart=" __stringify(CONFIG_SYS_MMC_IMG_LOAD_PART) "\0" \
 120         "mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \
 121         "mmcautodetect=yes\0" \
 122         "mmcargs=setenv bootargs console=${console} root=${mmcroot}\0 " \
 123         "loadbootscript=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
 124         "bootscript=echo Running bootscript from mmc ...; " \
 125                 "source\0" \
 126         "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
 127         "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
 128         "mmcboot=echo Booting from mmc ...; " \
 129                 "run mmcargs; " \
 130                 "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
 131                         "if run loadfdt; then " \
 132                                 "booti ${loadaddr} - ${fdt_addr}; " \
 133                         "else " \
 134                                 "echo WARN: Cannot load the DT; " \
 135                         "fi; " \
 136                 "else " \
 137                         "echo wait for boot; " \
 138                 "fi;\0" \
 139         "netargs=setenv bootargs console=${console} " \
 140                 "root=/dev/nfs " \
 141                 "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
 142         "netboot=echo Booting from net ...; " \
 143                 "run netargs;  " \
 144                 "if test ${ip_dyn} = yes; then " \
 145                         "setenv get_cmd dhcp; " \
 146                 "else " \
 147                         "setenv get_cmd tftp; " \
 148                 "fi; " \
 149                 "${get_cmd} ${loadaddr} ${image}; " \
 150                 "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
 151                         "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
 152                                 "booti ${loadaddr} - ${fdt_addr}; " \
 153                         "else " \
 154                                 "echo WARN: Cannot load the DT; " \
 155                         "fi; " \
 156                 "else " \
 157                         "booti; " \
 158                 "fi;\0"
 159
 160 #define CONFIG_BOOTCOMMAND \
 161            "mmc dev ${mmcdev}; if mmc rescan; then " \
 162                    "if run loadbootscript; then " \
 163                            "run bootscript; " \
 164                    "else " \
 165                            "if run loadimage; then " \
 166                                    "run mmcboot; " \
 167                            "else run netboot; " \
 168                            "fi; " \
 169                    "fi; " \
 170            "else booti ${loadaddr} - ${fdt_addr}; fi"
 171
 172 /* Link Definitions */
 173 #define CONFIG_LOADADDR                 0x40480000
 174
 175 #define CONFIG_SYS_LOAD_ADDR           CONFIG_LOADADDR
 176
 177 #define CONFIG_SYS_INIT_RAM_ADDR        0x40000000
 178 #define CONFIG_SYS_INIT_RAM_SIZE        0x80000
 179 #define CONFIG_SYS_INIT_SP_OFFSET \
 180         (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 181 #define CONFIG_SYS_INIT_SP_ADDR \
 182         (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
 183
 184 #define CONFIG_ENV_OVERWRITE
 185 #define CONFIG_ENV_OFFSET               (64 * SZ_64K)
 186 #define CONFIG_ENV_SIZE                 0x1000
 187 #define CONFIG_SYS_MMC_ENV_DEV          1   /* USDHC2 */
 188 #define CONFIG_MMCROOT                  "/dev/mmcblk1p2"  /* USDHC2 */
 189
 190 /* Size of malloc() pool */
 191 #define CONFIG_SYS_MALLOC_LEN           ((CONFIG_ENV_SIZE + (2 * 1024)) * 1024)
 192
 193 #define CONFIG_SYS_SDRAM_BASE           0x40000000
 194 #define PHYS_SDRAM                      0x40000000
 195 #define PHYS_SDRAM_SIZE                 0xC0000000 /* 3GB DDR */
 196
 197 #define CONFIG_SYS_MEMTEST_START        PHYS_SDRAM
 198 #define CONFIG_SYS_MEMTEST_END          (CONFIG_SYS_MEMTEST_START + \
 199                                         (PHYS_SDRAM_SIZE >> 1))
 200
 201 #define CONFIG_BAUDRATE                 115200
 202
 203 #define CONFIG_MXC_UART
 204 #define CONFIG_MXC_UART_BASE            UART1_BASE_ADDR
 205
 206 /* Monitor Command Prompt */
 207 #undef CONFIG_SYS_PROMPT
 208 #define CONFIG_SYS_PROMPT               "u-boot=> "
 209 #define CONFIG_SYS_PROMPT_HUSH_PS2      "> "
 210 #define CONFIG_SYS_CBSIZE               1024
 211 #define CONFIG_SYS_MAXARGS              64
 212 #define CONFIG_SYS_BARGSIZE             CONFIG_SYS_CBSIZE
 213 #define CONFIG_SYS_PBSIZE               (CONFIG_SYS_CBSIZE + \
 214                                         sizeof(CONFIG_SYS_PROMPT) + 16)
 215
 216 #define CONFIG_IMX_BOOTAUX
 217
 218 #define CONFIG_CMD_MMC
 219 #define CONFIG_FSL_ESDHC
 220 #define CONFIG_FSL_USDHC
 221
 222 #define CONFIG_SYS_FSL_USDHC_NUM        2
 223 #define CONFIG_SYS_FSL_ESDHC_ADDR       0
 224
 225 #define CONFIG_SYS_MMC_IMG_LOAD_PART    1
 226
 227 #define CONFIG_MXC_GPIO
 228
 229 #define CONFIG_CMD_FUSE
 230
 231 /* I2C Configs */
 232 #define CONFIG_SYS_I2C_SPEED              100000
 233
 234 #define CONFIG_OF_SYSTEM_SETUP
 235
 236 #ifndef CONFIG_SPL_BUILD
 237 #define CONFIG_DM_PMIC
 238 #endif
 239
 240 #endif