include/configs/ids8313.h

   1 /* SPDX-License-Identifier: GPL-2.0+ */
   2 /*
   3  * (C) Copyright 2013
   4  * Heiko Schocher, DENX Software Engineering, hs@denx.de.
   5  *
   6  * Based on:
   7  * Copyright (c) 2011 IDS GmbH, Germany
   8  * Sergej Stepanov <ste@ids.de>
   9  */
  10
  11 #ifndef __CONFIG_H
  12 #define __CONFIG_H
  13
  14 /*
  15  * High Level Configuration Options
  16  */
  17 #define CONFIG_FSL_ELBC
  18
  19 #define CONFIG_BOOT_RETRY_TIME          900
  20 #define CONFIG_BOOT_RETRY_MIN           30
  21 #define CONFIG_RESET_TO_RETRY
  22
  23 #define CONFIG_SYS_SICRH        0x00000000
  24 #define CONFIG_SYS_SICRL        (SICRL_LBC | SICRL_SPI_D)
  25
  26 #define CONFIG_HWCONFIG
  27
  28 /*
  29  * Definitions for initial stack pointer and data area (in DCACHE )
  30  */
  31 #define CONFIG_SYS_INIT_RAM_LOCK
  32 #define CONFIG_SYS_INIT_RAM_ADDR        0xFD000000
  33 #define CONFIG_SYS_INIT_RAM_SIZE        0x1000  /* End of used area in DPRAM */
  34 #define CONFIG_SYS_GBL_DATA_SIZE        0x100
  35 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE \
  36                                          - CONFIG_SYS_GBL_DATA_SIZE)
  37 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
  38
  39 /*
  40  * Local Bus LCRR and LBCR regs
  41  */
  42 #define CONFIG_SYS_LCRR_EADC            LCRR_EADC_1
  43 #define CONFIG_SYS_LCRR_CLKDIV          LCRR_CLKDIV_2
  44 #define CONFIG_SYS_LBC_LBCR             (0x00040000 |\
  45                                          (0xFF << LBCR_BMT_SHIFT) |\
  46                                          0xF)
  47
  48 #define CONFIG_SYS_LBC_MRTPR            0x20000000
  49
  50 /*
  51  * Internal Definitions
  52  */
  53 /*
  54  * DDR Setup
  55  */
  56 #define CONFIG_SYS_DDR_BASE             0x00000000
  57 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_BASE
  58 #define CONFIG_SYS_DDR_SDRAM_BASE       CONFIG_SYS_DDR_BASE
  59
  60 /*
  61  * Manually set up DDR parameters,
  62  * as this board has not the SPD connected to I2C.
  63  */
  64 #define CONFIG_SYS_DDR_SIZE             256             /* MB */
  65 #define CONFIG_SYS_DDR_CONFIG           (CSCONFIG_EN |\
  66                                          0x00010000 |\
  67                                          CSCONFIG_ROW_BIT_13 |\
  68                                          CSCONFIG_COL_BIT_10)
  69
  70 #define CONFIG_SYS_DDR_CONFIG_256       (CONFIG_SYS_DDR_CONFIG | \
  71                                          CSCONFIG_BANK_BIT_3)
  72
  73 #define CONFIG_SYS_DDR_TIMING_3 (1 << 16)       /* ext refrec */
  74 #define CONFIG_SYS_DDR_TIMING_0 ((3 << TIMING_CFG0_RWT_SHIFT) |\
  75                                 (3 << TIMING_CFG0_WRT_SHIFT) |\
  76                                 (3 << TIMING_CFG0_RRT_SHIFT) |\
  77                                 (3 << TIMING_CFG0_WWT_SHIFT) |\
  78                                 (6 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) |\
  79                                 (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) |\
  80                                 (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \
  81                                 (2 << TIMING_CFG0_MRS_CYC_SHIFT))
  82 #define CONFIG_SYS_DDR_TIMING_1 ((4 << TIMING_CFG1_PRETOACT_SHIFT) |\
  83                                 (12 << TIMING_CFG1_ACTTOPRE_SHIFT) |\
  84                                 (4 << TIMING_CFG1_ACTTORW_SHIFT) |\
  85                                 (7 << TIMING_CFG1_CASLAT_SHIFT) |\
  86                                 (4 << TIMING_CFG1_REFREC_SHIFT) |\
  87                                 (4 << TIMING_CFG1_WRREC_SHIFT) |\
  88                                 (2 << TIMING_CFG1_ACTTOACT_SHIFT) |\
  89                                 (2 << TIMING_CFG1_WRTORD_SHIFT))
  90 #define CONFIG_SYS_DDR_TIMING_2 ((1 << TIMING_CFG2_ADD_LAT_SHIFT) |\
  91                                 (5 << TIMING_CFG2_CPO_SHIFT) |\
  92                                 (4 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) |\
  93                                 (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) |\
  94                                 (0 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) |\
  95                                 (1 << TIMING_CFG2_CKE_PLS_SHIFT) |\
  96                                 (6 << TIMING_CFG2_FOUR_ACT_SHIFT))
  97
  98 #define CONFIG_SYS_DDR_INTERVAL ((0x800 << SDRAM_INTERVAL_REFINT_SHIFT) |\
  99                                 (0x800 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
 100
 101 #define CONFIG_SYS_SDRAM_CFG            (SDRAM_CFG_SREN |\
 102                                          SDRAM_CFG_2T_EN | SDRAM_CFG_HSE |\
 103                                          SDRAM_CFG_DBW_32 |\
 104                                          SDRAM_CFG_SDRAM_TYPE_DDR2)
 105
 106 #define CONFIG_SYS_SDRAM_CFG2           0x00401000
 107 #define CONFIG_SYS_DDR_MODE             ((0x0448 << SDRAM_MODE_ESD_SHIFT) |\
 108                                          (0x0242 << SDRAM_MODE_SD_SHIFT))
 109 #define CONFIG_SYS_DDR_MODE_2           0x00000000
 110 #define CONFIG_SYS_DDR_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_075
 111 #define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN |\
 112                                          DDRCDR_PZ_NOMZ |\
 113                                          DDRCDR_NZ_NOMZ |\
 114                                          DDRCDR_ODT |\
 115                                          DDRCDR_M_ODR |\
 116                                          DDRCDR_Q_DRN)
 117
 118 /*
 119  * on-board devices
 120  */
 121 #define CONFIG_TSEC1
 122 #define CONFIG_TSEC2
 123
 124 /*
 125  * NOR FLASH setup
 126  */
 127 #define CONFIG_SYS_FLASH_CFI_WIDTH      FLASH_CFI_8BIT
 128 #define CONFIG_FLASH_SHOW_PROGRESS      50
 129
 130 #define CONFIG_SYS_FLASH_BASE           0xFF800000
 131 #define CONFIG_SYS_FLASH_SIZE           8
 132
 133
 134 #define CONFIG_SYS_MAX_FLASH_BANKS      1
 135 #define CONFIG_SYS_MAX_FLASH_SECT       128
 136
 137 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000
 138 #define CONFIG_SYS_FLASH_WRITE_TOUT     500
 139
 140 /*
 141  * NAND FLASH setup
 142  */
 143 #define CONFIG_SYS_NAND_BASE            0xE1000000
 144 #define CONFIG_SYS_MAX_NAND_DEVICE      1
 145 #define CONFIG_SYS_NAND_MAX_CHIPS       1
 146 #define CONFIG_NAND_FSL_ELBC
 147 #define CONFIG_SYS_NAND_PAGE_SIZE       (2048)
 148 #define CONFIG_SYS_NAND_BLOCK_SIZE      (128 << 10)
 149 #define NAND_CACHE_PAGES                64
 150
 151
 152 /*
 153  * MRAM setup
 154  */
 155 #define CONFIG_SYS_MRAM_BASE            0xE2000000
 156 #define CONFIG_SYS_MRAM_SIZE            0x20000 /* 128 Kb */
 157
 158 #define CONFIG_SYS_OR_TIMING_MRAM
 159
 160
 161 /*
 162  * CPLD setup
 163  */
 164 #define CONFIG_SYS_CPLD_BASE            0xE3000000
 165 #define CONFIG_SYS_CPLD_SIZE            0x8000
 166
 167 #define CONFIG_SYS_OR_TIMING_MRAM
 168
 169
 170 /*
 171  * HW-Watchdog
 172  */
 173 #define CONFIG_WATCHDOG         1
 174 #define CONFIG_SYS_WATCHDOG_VALUE       0xFFFF
 175
 176 /*
 177  * I2C setup
 178  */
 179 #define CONFIG_SYS_I2C
 180 #define CONFIG_SYS_I2C_FSL
 181 #define CONFIG_SYS_FSL_I2C_SPEED        400000
 182 #define CONFIG_SYS_FSL_I2C_SLAVE        0x7F
 183 #define CONFIG_SYS_FSL_I2C_OFFSET       0x3100
 184 #define CONFIG_RTC_PCF8563
 185 #define CONFIG_SYS_I2C_RTC_ADDR 0x51
 186
 187 /*
 188  * Ethernet setup
 189  */
 190 #ifdef CONFIG_TSEC1
 191 #define CONFIG_HAS_ETH0
 192 #define CONFIG_TSEC1_NAME               "TSEC0"
 193 #define CONFIG_SYS_TSEC1_OFFSET 0x24000
 194 #define TSEC1_PHY_ADDR                  0x1
 195 #define TSEC1_FLAGS                     TSEC_GIGABIT
 196 #define TSEC1_PHYIDX                    0
 197 #endif
 198
 199 #ifdef CONFIG_TSEC2
 200 #define CONFIG_HAS_ETH1
 201 #define CONFIG_TSEC2_NAME               "TSEC1"
 202 #define CONFIG_SYS_TSEC2_OFFSET 0x25000
 203 #define TSEC2_PHY_ADDR                  0x3
 204 #define TSEC2_FLAGS                     TSEC_GIGABIT
 205 #define TSEC2_PHYIDX                    0
 206 #endif
 207 #define CONFIG_ETHPRIME         "TSEC1"
 208
 209 /*
 210  * Serial Port
 211  */
 212 #define CONFIG_SYS_NS16550_SERIAL
 213 #define CONFIG_SYS_NS16550_REG_SIZE     1
 214
 215 #define CONFIG_SYS_BAUDRATE_TABLE       \
 216         {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
 217 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x4500)
 218 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x4600)
 219 #define CONFIG_SYS_NS16550_CLK          (get_bus_freq(0))
 220
 221 #define CONFIG_HAS_FSL_DR_USB
 222 #define CONFIG_SYS_SCCR_USBDRCM 3
 223
 224 /*
 225  * U-Boot environment setup
 226  */
 227 #define CONFIG_BOOTP_BOOTFILESIZE
 228
 229 /*
 230  * The reserved memory
 231  */
 232 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
 233 #define CONFIG_SYS_MONITOR_LEN          (768 * 1024)
 234 #define CONFIG_SYS_MALLOC_LEN           (8 * 1024 * 1024)
 235
 236 /*
 237  * Environment Configuration
 238  */
 239 #define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE \
 240                                 + CONFIG_SYS_MONITOR_LEN)
 241 #define CONFIG_ENV_SIZE         0x20000
 242 #define CONFIG_ENV_ADDR_REDUND  (CONFIG_ENV_ADDR + CONFIG_ENV_SIZE)
 243 #define CONFIG_ENV_SIZE_REDUND  (CONFIG_ENV_SIZE)
 244
 245 #define CONFIG_NETDEV                   eth1
 246 #define CONFIG_HOSTNAME         "ids8313"
 247 #define CONFIG_ROOTPATH         "/opt/eldk-4.2/ppc_6xx"
 248 #define CONFIG_BOOTFILE         "ids8313/uImage"
 249 #define CONFIG_UBOOTPATH                "ids8313/u-boot.bin"
 250 #define CONFIG_FDTFILE                  "ids8313/ids8313.dtb"
 251 #define CONFIG_LOADADDR         0x400000
 252 #define CONFIG_ENV_FLAGS_LIST_STATIC "ethaddr:mo,eth1addr:mo"
 253
 254 /* Initial Memory map for Linux*/
 255 #define CONFIG_SYS_BOOTMAPSZ            (256 << 20)
 256
 257 /*
 258  * Miscellaneous configurable options
 259  */
 260 #define CONFIG_SYS_CBSIZE               1024
 261 #define CONFIG_SYS_BARGSIZE             CONFIG_SYS_CBSIZE
 262
 263 #define CONFIG_SYS_MEMTEST_START        0x00001000
 264 #define CONFIG_SYS_MEMTEST_END          0x00C00000
 265
 266 #define CONFIG_SYS_LOAD_ADDR            0x100000
 267 #define CONFIG_LOADS_ECHO
 268 #define CONFIG_TIMESTAMP
 269 #define CONFIG_PREBOOT                  "echo;" \
 270                                         "echo Type \\\"run nfsboot\\\" " \
 271                                         "to mount root filesystem over NFS;echo"
 272 #define CONFIG_BOOTCOMMAND              "run boot_cramfs"
 273 #undef  CONFIG_SYS_LOADS_BAUD_CHANGE
 274
 275 #define CONFIG_JFFS2_NAND
 276 #define CONFIG_JFFS2_DEV                "0"
 277
 278 /* mtdparts command line support */
 279
 280 #define CONFIG_EXTRA_ENV_SETTINGS \
 281         "netdev=" __stringify(CONFIG_NETDEV) "\0"                       \
 282         "ethprime=TSEC1\0"                                              \
 283         "uboot=" __stringify(CONFIG_UBOOTPATH) "\0"                     \
 284         "tftpflash=tftpboot ${loadaddr} ${uboot}; "                     \
 285                 "protect off " __stringify(CONFIG_SYS_TEXT_BASE)        \
 286                 " +${filesize}; "                                       \
 287                 "erase " __stringify(CONFIG_SYS_TEXT_BASE)              \
 288                 " +${filesize}; "                                       \
 289                 "cp.b ${loadaddr} " __stringify(CONFIG_SYS_TEXT_BASE)   \
 290                 " ${filesize}; "                                        \
 291                 "protect on " __stringify(CONFIG_SYS_TEXT_BASE)         \
 292                 " +${filesize}; "                                       \
 293                 "cmp.b ${loadaddr} " __stringify(CONFIG_SYS_TEXT_BASE)  \
 294                 " ${filesize}\0"                                        \
 295         "console=ttyS0\0"                                               \
 296         "fdtaddr=0x780000\0"                                            \
 297         "kernel_addr=ff800000\0"                                        \
 298         "fdtfile=" __stringify(CONFIG_FDTFILE) "\0"                     \
 299         "setbootargs=setenv bootargs "                                  \
 300                 "root=${rootdev} rw console=${console},"                \
 301                         "${baudrate} ${othbootargs}\0"                  \
 302         "setipargs=setenv bootargs root=${rootdev} rw "                 \
 303                         "nfsroot=${serverip}:${rootpath} "              \
 304                         "ip=${ipaddr}:${serverip}:${gatewayip}:"        \
 305                         "${netmask}:${hostname}:${netdev}:off "         \
 306                         "console=${console},${baudrate} ${othbootargs}\0" \
 307         "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0"              \
 308         "mtdids=" CONFIG_MTDIDS_DEFAULT "\0"                                    \
 309         "mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0"                                \
 310         "\0"
 311
 312 #define CONFIG_NFSBOOTCOMMAND                                           \
 313         "setenv rootdev /dev/nfs;"                                      \
 314         "run setipargs;run addmtd;"                                     \
 315         "tftp ${loadaddr} ${bootfile};"                         \
 316         "tftp ${fdtaddr} ${fdtfile};"                                   \
 317         "fdt addr ${fdtaddr};"                                          \
 318         "bootm ${loadaddr} - ${fdtaddr}"
 319
 320 /* UBI Support */
 321
 322 #endif  /* __CONFIG_H */