3 * Heiko Schocher, DENX Software Engineering, hs@denx.de.
6 * Copyright (c) 2011 IDS GmbH, Germany
7 * Sergej Stepanov <ste@ids.de>
9 * SPDX-License-Identifier: GPL-2.0+
16 * High Level Configuration Options
18 #define CONFIG_MPC831x
19 #define CONFIG_MPC8313
20 #define CONFIG_IDS8313
22 #define CONFIG_FSL_ELBC
24 #define CONFIG_MISC_INIT_R
26 #define CONFIG_BOOT_RETRY_TIME 900
27 #define CONFIG_BOOT_RETRY_MIN 30
28 #define CONFIG_RESET_TO_RETRY
30 #define CONFIG_83XX_CLKIN 66000000 /* in Hz */
31 #define CONFIG_SYS_CLK_FREQ CONFIG_83XX_CLKIN
33 #define CONFIG_SYS_IMMR 0xF0000000
35 #define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth (0-3) */
36 #define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count (0-7) */
39 * Hardware Reset Configuration Word
40 * if CLKIN is 66.000MHz, then
41 * CSB = 132MHz, CORE = 264MHz, DDRC = 264MHz, LBC = 132MHz
43 #define CONFIG_SYS_HRCW_LOW (0x20000000 /* reserved, must be set */ |\
44 HRCWL_DDR_TO_SCB_CLK_2X1 |\
45 HRCWL_CSB_TO_CLKIN_2X1 |\
46 HRCWL_CORE_TO_CSB_2X1)
48 #define CONFIG_SYS_HRCW_HIGH (HRCWH_PCI_HOST |\
50 HRCWH_FROM_0XFFF00100 |\
51 HRCWH_BOOTSEQ_DISABLE |\
52 HRCWH_SW_WATCHDOG_DISABLE |\
53 HRCWH_ROM_LOC_LOCAL_8BIT |\
54 HRCWH_RL_EXT_LEGACY |\
55 HRCWH_TSEC1M_IN_MII |\
56 HRCWH_TSEC2M_IN_MII |\
59 #define CONFIG_SYS_SICRH 0x00000000
60 #define CONFIG_SYS_SICRL (SICRL_LBC | SICRL_SPI_D)
62 #define CONFIG_HWCONFIG
64 #define CONFIG_SYS_HID0_INIT 0x000000000
65 #define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK |\
66 HID0_ENABLE_INSTRUCTION_CACHE |\
67 HID0_DISABLE_DYNAMIC_POWER_MANAGMENT)
69 #define CONFIG_SYS_HID2 (HID2_HBE | 0x00020000)
72 * Definitions for initial stack pointer and data area (in DCACHE )
74 #define CONFIG_SYS_INIT_RAM_LOCK
75 #define CONFIG_SYS_INIT_RAM_ADDR 0xFD000000
76 #define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* End of used area in DPRAM */
77 #define CONFIG_SYS_GBL_DATA_SIZE 0x100
78 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE \
79 - CONFIG_SYS_GBL_DATA_SIZE)
80 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
83 * Local Bus LCRR and LBCR regs
85 #define CONFIG_SYS_LCRR_EADC LCRR_EADC_1
86 #define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_2
87 #define CONFIG_SYS_LBC_LBCR (0x00040000 |\
88 (0xFF << LBCR_BMT_SHIFT) |\
91 #define CONFIG_SYS_LBC_MRTPR 0x20000000
94 * Internal Definitions
99 #define CONFIG_SYS_DDR_BASE 0x00000000
100 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE
101 #define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE
104 * Manually set up DDR parameters,
105 * as this board has not the SPD connected to I2C.
107 #define CONFIG_SYS_DDR_SIZE 256 /* MB */
108 #define CONFIG_SYS_DDR_CONFIG (CSCONFIG_EN |\
110 CSCONFIG_ROW_BIT_13 |\
113 #define CONFIG_SYS_DDR_CONFIG_256 (CONFIG_SYS_DDR_CONFIG | \
116 #define CONFIG_SYS_DDR_TIMING_3 (1 << 16) /* ext refrec */
117 #define CONFIG_SYS_DDR_TIMING_0 ((3 << TIMING_CFG0_RWT_SHIFT) |\
118 (3 << TIMING_CFG0_WRT_SHIFT) |\
119 (3 << TIMING_CFG0_RRT_SHIFT) |\
120 (3 << TIMING_CFG0_WWT_SHIFT) |\
121 (6 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) |\
122 (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) |\
123 (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \
124 (2 << TIMING_CFG0_MRS_CYC_SHIFT))
125 #define CONFIG_SYS_DDR_TIMING_1 ((4 << TIMING_CFG1_PRETOACT_SHIFT) |\
126 (12 << TIMING_CFG1_ACTTOPRE_SHIFT) |\
127 (4 << TIMING_CFG1_ACTTORW_SHIFT) |\
128 (7 << TIMING_CFG1_CASLAT_SHIFT) |\
129 (4 << TIMING_CFG1_REFREC_SHIFT) |\
130 (4 << TIMING_CFG1_WRREC_SHIFT) |\
131 (2 << TIMING_CFG1_ACTTOACT_SHIFT) |\
132 (2 << TIMING_CFG1_WRTORD_SHIFT))
133 #define CONFIG_SYS_DDR_TIMING_2 ((1 << TIMING_CFG2_ADD_LAT_SHIFT) |\
134 (5 << TIMING_CFG2_CPO_SHIFT) |\
135 (4 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) |\
136 (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) |\
137 (0 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) |\
138 (1 << TIMING_CFG2_CKE_PLS_SHIFT) |\
139 (6 << TIMING_CFG2_FOUR_ACT_SHIFT))
141 #define CONFIG_SYS_DDR_INTERVAL ((0x800 << SDRAM_INTERVAL_REFINT_SHIFT) |\
142 (0x800 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
144 #define CONFIG_SYS_SDRAM_CFG (SDRAM_CFG_SREN |\
145 SDRAM_CFG_2T_EN | SDRAM_CFG_HSE |\
147 SDRAM_CFG_SDRAM_TYPE_DDR2)
149 #define CONFIG_SYS_SDRAM_CFG2 0x00401000
150 #define CONFIG_SYS_DDR_MODE ((0x0448 << SDRAM_MODE_ESD_SHIFT) |\
151 (0x0242 << SDRAM_MODE_SD_SHIFT))
152 #define CONFIG_SYS_DDR_MODE_2 0x00000000
153 #define CONFIG_SYS_DDR_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_075
154 #define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN |\
166 #define CONFIG_TSEC_ENET
167 #define CONFIG_HARD_SPI
172 #define CONFIG_SYS_FLASH_CFI
173 #define CONFIG_FLASH_CFI_DRIVER
174 #define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_8BIT
175 #define CONFIG_FLASH_SHOW_PROGRESS 50
176 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
178 #define CONFIG_SYS_FLASH_BASE 0xFF800000
179 #define CONFIG_SYS_FLASH_SIZE 8
180 #define CONFIG_SYS_FLASH_PROTECTION
182 #define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE
183 #define CONFIG_SYS_LBLAWAR0_PRELIM 0x80000016
185 #define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE |\
190 #define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) |\
196 #define CONFIG_SYS_MAX_FLASH_BANKS 1
197 #define CONFIG_SYS_MAX_FLASH_SECT 128
199 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000
200 #define CONFIG_SYS_FLASH_WRITE_TOUT 500
205 #define CONFIG_SYS_NAND_BASE 0xE1000000
206 #define CONFIG_SYS_MAX_NAND_DEVICE 1
207 #define CONFIG_SYS_NAND_MAX_CHIPS 1
208 #define CONFIG_NAND_FSL_ELBC
209 #define CONFIG_SYS_NAND_PAGE_SIZE (2048)
210 #define CONFIG_SYS_NAND_BLOCK_SIZE (128 << 10)
211 #define NAND_CACHE_PAGES 64
213 #define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_NAND_BASE
214 #define CONFIG_SYS_LBLAWAR1_PRELIM 0x8000000E
215 #define CONFIG_SYS_NAND_LBLAWBAR_PRELIM CONFIG_SYS_LBLAWBAR1_PRELIM
216 #define CONFIG_SYS_NAND_LBLAWAR_PRELIM CONFIG_SYS_LBLAWAR1_PRELIM
218 #define CONFIG_SYS_BR1_PRELIM ((CONFIG_SYS_NAND_BASE) |\
219 (2<<BR_DECC_SHIFT) |\
224 #define CONFIG_SYS_OR1_PRELIM (0xFFFF8000 |\
237 #define CONFIG_SYS_MRAM_BASE 0xE2000000
238 #define CONFIG_SYS_MRAM_SIZE 0x20000 /* 128 Kb */
239 #define CONFIG_SYS_LBLAWBAR2_PRELIM CONFIG_SYS_MRAM_BASE
240 #define CONFIG_SYS_LBLAWAR2_PRELIM 0x80000010 /* 128 Kb */
242 #define CONFIG_SYS_OR_TIMING_MRAM
244 #define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_MRAM_BASE |\
249 #define CONFIG_SYS_OR2_PRELIM 0xFFFE0C74
254 #define CONFIG_SYS_CPLD_BASE 0xE3000000
255 #define CONFIG_SYS_CPLD_SIZE 0x8000
256 #define CONFIG_SYS_LBLAWBAR3_PRELIM CONFIG_SYS_CPLD_BASE
257 #define CONFIG_SYS_LBLAWAR3_PRELIM 0x8000000E
259 #define CONFIG_SYS_OR_TIMING_MRAM
261 #define CONFIG_SYS_BR3_PRELIM (CONFIG_SYS_CPLD_BASE |\
266 #define CONFIG_SYS_OR3_PRELIM 0xFFFF8814
271 #define CONFIG_WATCHDOG 1
272 #define CONFIG_SYS_WATCHDOG_VALUE 0xFFFF
277 #define CONFIG_SYS_I2C
278 #define CONFIG_SYS_I2C_FSL
279 #define CONFIG_SYS_FSL_I2C_SPEED 400000
280 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
281 #define CONFIG_SYS_FSL_I2C_OFFSET 0x3100
282 #define CONFIG_RTC_PCF8563
283 #define CONFIG_SYS_I2C_RTC_ADDR 0x51
288 #ifdef CONFIG_HARD_SPI
289 #define CONFIG_MPC8XXX_SPI
290 #define CONFIG_SYS_GPIO1_PRELIM
291 #define CONFIG_SYS_GPIO1_DIR 0x00000001
292 #define CONFIG_SYS_GPIO1_DAT 0x00000001
299 #define CONFIG_HAS_ETH0
300 #define CONFIG_TSEC1_NAME "TSEC0"
301 #define CONFIG_SYS_TSEC1_OFFSET 0x24000
302 #define TSEC1_PHY_ADDR 0x1
303 #define TSEC1_FLAGS TSEC_GIGABIT
304 #define TSEC1_PHYIDX 0
308 #define CONFIG_HAS_ETH1
309 #define CONFIG_TSEC2_NAME "TSEC1"
310 #define CONFIG_SYS_TSEC2_OFFSET 0x25000
311 #define TSEC2_PHY_ADDR 0x3
312 #define TSEC2_FLAGS TSEC_GIGABIT
313 #define TSEC2_PHYIDX 0
315 #define CONFIG_ETHPRIME "TSEC1"
320 #define CONFIG_CONS_INDEX 1
321 #define CONFIG_SYS_NS16550_SERIAL
322 #define CONFIG_SYS_NS16550_REG_SIZE 1
324 #define CONFIG_SYS_BAUDRATE_TABLE \
325 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
326 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x4500)
327 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x4600)
328 #define CONFIG_SYS_NS16550_CLK (CONFIG_83XX_CLKIN * 2)
330 #define CONFIG_HAS_FSL_DR_USB
331 #define CONFIG_SYS_SCCR_USBDRCM 3
336 #define CONFIG_HIGH_BATS
338 /* DDR @ 0x00000000 */
339 #define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE |\
341 #define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE |\
345 #define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L
346 #define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U
348 /* Initial RAM @ 0xFD000000 */
349 #define CONFIG_SYS_IBAT1L (CONFIG_SYS_INIT_RAM_ADDR |\
352 #define CONFIG_SYS_IBAT1U (CONFIG_SYS_INIT_RAM_ADDR |\
356 #define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
357 #define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
359 /* FLASH @ 0xFF800000 */
360 #define CONFIG_SYS_IBAT2L (CONFIG_SYS_FLASH_BASE |\
363 #define CONFIG_SYS_IBAT2U (CONFIG_SYS_FLASH_BASE |\
367 #define CONFIG_SYS_DBAT2L (CONFIG_SYS_FLASH_BASE |\
371 #define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U
373 #define CONFIG_SYS_IBAT3L (0)
374 #define CONFIG_SYS_IBAT3U (0)
375 #define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L
376 #define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
378 #define CONFIG_SYS_IBAT4L (0)
379 #define CONFIG_SYS_IBAT4U (0)
380 #define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L
381 #define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U
383 /* IMMRBAR @ 0xF0000000 */
384 #define CONFIG_SYS_IBAT5L (CONFIG_SYS_IMMR |\
388 #define CONFIG_SYS_IBAT5U (CONFIG_SYS_IMMR |\
392 #define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L
393 #define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U
395 /* NAND-Flash @ 0xE1000000, MRAM @ 0xE2000000, CPLD @ 0xE3000000 */
396 #define CONFIG_SYS_IBAT6L (0xE0000000 |\
399 #define CONFIG_SYS_IBAT6U (0xE0000000 |\
403 #define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L
404 #define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U
406 #define CONFIG_SYS_IBAT7L (0)
407 #define CONFIG_SYS_IBAT7U (0)
408 #define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L
409 #define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U
412 * U-Boot environment setup
414 #define CONFIG_CMDLINE_EDITING
415 #define CONFIG_BOOTP_SUBNETMASK
416 #define CONFIG_BOOTP_GATEWAY
417 #define CONFIG_BOOTP_HOSTNAME
418 #define CONFIG_BOOTP_BOOTPATH
419 #define CONFIG_BOOTP_BOOTFILESIZE
422 * The reserved memory
424 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
425 #define CONFIG_SYS_MONITOR_LEN (768 * 1024)
426 #define CONFIG_SYS_MALLOC_LEN (8 * 1024 * 1024)
429 * Environment Configuration
431 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE \
432 + CONFIG_SYS_MONITOR_LEN)
433 #define CONFIG_ENV_SIZE 0x20000
434 #define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SIZE)
435 #define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
437 #define CONFIG_NETDEV eth1
438 #define CONFIG_HOSTNAME ids8313
439 #define CONFIG_ROOTPATH "/opt/eldk-4.2/ppc_6xx"
440 #define CONFIG_BOOTFILE "ids8313/uImage"
441 #define CONFIG_UBOOTPATH "ids8313/u-boot.bin"
442 #define CONFIG_FDTFILE "ids8313/ids8313.dtb"
443 #define CONFIG_LOADADDR 0x400000
444 #define CONFIG_ENV_FLAGS_LIST_STATIC "ethaddr:mo,eth1addr:mo"
446 /* Initial Memory map for Linux*/
447 #define CONFIG_SYS_BOOTMAPSZ (256 << 20)
450 * Miscellaneous configurable options
452 #define CONFIG_SYS_LONGHELP
453 #define CONFIG_SYS_CBSIZE 1024
454 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE \
455 + sizeof(CONFIG_SYS_PROMPT)+16)
456 #define CONFIG_SYS_MAXARGS 16
457 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
459 #define CONFIG_SYS_MEMTEST_START 0x00001000
460 #define CONFIG_SYS_MEMTEST_END 0x00C00000
462 #define CONFIG_SYS_LOAD_ADDR 0x100000
464 #define CONFIG_LOADS_ECHO
465 #define CONFIG_TIMESTAMP
466 #define CONFIG_PREBOOT "echo;" \
467 "echo Type \\\"run nfsboot\\\" " \
468 "to mount root filesystem over NFS;echo"
469 #define CONFIG_BOOTCOMMAND "run boot_cramfs"
470 #undef CONFIG_SYS_LOADS_BAUD_CHANGE
472 #define CONFIG_JFFS2_NAND
473 #define CONFIG_JFFS2_DEV "0"
475 /* mtdparts command line support */
476 #define CONFIG_FLASH_CFI_MTD
477 #define CONFIG_MTD_DEVICE
478 #define MTDIDS_DEFAULT "nor0=ff800000.flash,nand0=e1000000.flash"
479 #define MTDPARTS_DEFAULT "mtdparts=ff800000.flash:7m(dum)," \
481 "128k(BOOT-ENV),128k(BOOT-REDENV);" \
482 "e1000000.flash:-(ubi)"
484 #define CONFIG_EXTRA_ENV_SETTINGS \
485 "netdev=" __stringify(CONFIG_NETDEV) "\0" \
487 "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \
488 "tftpflash=tftpboot ${loadaddr} ${uboot}; " \
489 "protect off " __stringify(CONFIG_SYS_TEXT_BASE) \
491 "erase " __stringify(CONFIG_SYS_TEXT_BASE) \
493 "cp.b ${loadaddr} " __stringify(CONFIG_SYS_TEXT_BASE) \
495 "protect on " __stringify(CONFIG_SYS_TEXT_BASE) \
497 "cmp.b ${loadaddr} " __stringify(CONFIG_SYS_TEXT_BASE) \
500 "fdtaddr=0x780000\0" \
501 "kernel_addr=ff800000\0" \
502 "fdtfile=" __stringify(CONFIG_FDTFILE) "\0" \
503 "setbootargs=setenv bootargs " \
504 "root=${rootdev} rw console=${console}," \
505 "${baudrate} ${othbootargs}\0" \
506 "setipargs=setenv bootargs root=${rootdev} rw " \
507 "nfsroot=${serverip}:${rootpath} " \
508 "ip=${ipaddr}:${serverip}:${gatewayip}:" \
509 "${netmask}:${hostname}:${netdev}:off " \
510 "console=${console},${baudrate} ${othbootargs}\0" \
511 "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \
512 "mtdids=" MTDIDS_DEFAULT "\0" \
513 "mtdparts=" MTDPARTS_DEFAULT "\0" \
516 #define CONFIG_NFSBOOTCOMMAND \
517 "setenv rootdev /dev/nfs;" \
518 "run setipargs;run addmtd;" \
519 "tftp ${loadaddr} ${bootfile};" \
520 "tftp ${fdtaddr} ${fdtfile};" \
521 "fdt addr ${fdtaddr};" \
522 "bootm ${loadaddr} - ${fdtaddr}"
525 #define CONFIG_MTD_PARTITIONS
527 /* bootcount support */
528 #define CONFIG_BOOTCOUNT_LIMIT
529 #define CONFIG_BOOTCOUNT_I2C
530 #define CONFIG_BOOTCOUNT_ALEN 1
531 #define CONFIG_SYS_BOOTCOUNT_ADDR 0x9
533 #define CONFIG_IMAGE_FORMAT_LEGACY
535 #endif /* __CONFIG_H */