include/configs/ids8313.h

   1 /* SPDX-License-Identifier: GPL-2.0+ */
   2 /*
   3  * (C) Copyright 2013
   4  * Heiko Schocher, DENX Software Engineering, hs@denx.de.
   5  *
   6  * Based on:
   7  * Copyright (c) 2011 IDS GmbH, Germany
   8  * Sergej Stepanov <ste@ids.de>
   9  */
  10
  11 #ifndef __CONFIG_H
  12 #define __CONFIG_H
  13
  14 #include <linux/stringify.h>
  15
  16 /*
  17  * High Level Configuration Options
  18  */
  19 #define CONFIG_BOOT_RETRY_TIME          900
  20 #define CONFIG_BOOT_RETRY_MIN           30
  21 #define CONFIG_RESET_TO_RETRY
  22
  23 #define CONFIG_SYS_SICRH        0x00000000
  24 #define CONFIG_SYS_SICRL        (SICRL_LBC | SICRL_SPI_D)
  25
  26 #define CONFIG_HWCONFIG
  27
  28 /*
  29  * Definitions for initial stack pointer and data area (in DCACHE )
  30  */
  31 #define CONFIG_SYS_INIT_RAM_LOCK
  32 #define CONFIG_SYS_INIT_RAM_ADDR        0xFD000000
  33 #define CONFIG_SYS_INIT_RAM_SIZE        0x1000  /* End of used area in DPRAM */
  34 #define CONFIG_SYS_GBL_DATA_SIZE        0x100
  35 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE \
  36                                          - CONFIG_SYS_GBL_DATA_SIZE)
  37 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
  38
  39 /*
  40  * Internal Definitions
  41  */
  42 /*
  43  * DDR Setup
  44  */
  45 #define CONFIG_SYS_SDRAM_BASE           0x00000000
  46
  47 /*
  48  * Manually set up DDR parameters,
  49  * as this board has not the SPD connected to I2C.
  50  */
  51 #define CONFIG_SYS_DDR_SIZE             256             /* MB */
  52 #define CONFIG_SYS_DDR_CONFIG           (CSCONFIG_EN |\
  53                                          0x00010000 |\
  54                                          CSCONFIG_ROW_BIT_13 |\
  55                                          CSCONFIG_COL_BIT_10)
  56
  57 #define CONFIG_SYS_DDR_CONFIG_256       (CONFIG_SYS_DDR_CONFIG | \
  58                                          CSCONFIG_BANK_BIT_3)
  59
  60 #define CONFIG_SYS_DDR_TIMING_3 (1 << 16)       /* ext refrec */
  61 #define CONFIG_SYS_DDR_TIMING_0 ((3 << TIMING_CFG0_RWT_SHIFT) |\
  62                                 (3 << TIMING_CFG0_WRT_SHIFT) |\
  63                                 (3 << TIMING_CFG0_RRT_SHIFT) |\
  64                                 (3 << TIMING_CFG0_WWT_SHIFT) |\
  65                                 (6 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) |\
  66                                 (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) |\
  67                                 (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \
  68                                 (2 << TIMING_CFG0_MRS_CYC_SHIFT))
  69 #define CONFIG_SYS_DDR_TIMING_1 ((4 << TIMING_CFG1_PRETOACT_SHIFT) |\
  70                                 (12 << TIMING_CFG1_ACTTOPRE_SHIFT) |\
  71                                 (4 << TIMING_CFG1_ACTTORW_SHIFT) |\
  72                                 (7 << TIMING_CFG1_CASLAT_SHIFT) |\
  73                                 (4 << TIMING_CFG1_REFREC_SHIFT) |\
  74                                 (4 << TIMING_CFG1_WRREC_SHIFT) |\
  75                                 (2 << TIMING_CFG1_ACTTOACT_SHIFT) |\
  76                                 (2 << TIMING_CFG1_WRTORD_SHIFT))
  77 #define CONFIG_SYS_DDR_TIMING_2 ((1 << TIMING_CFG2_ADD_LAT_SHIFT) |\
  78                                 (5 << TIMING_CFG2_CPO_SHIFT) |\
  79                                 (4 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) |\
  80                                 (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) |\
  81                                 (0 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) |\
  82                                 (1 << TIMING_CFG2_CKE_PLS_SHIFT) |\
  83                                 (6 << TIMING_CFG2_FOUR_ACT_SHIFT))
  84
  85 #define CONFIG_SYS_DDR_INTERVAL ((0x800 << SDRAM_INTERVAL_REFINT_SHIFT) |\
  86                                 (0x800 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
  87
  88 #define CONFIG_SYS_SDRAM_CFG            (SDRAM_CFG_SREN |\
  89                                          SDRAM_CFG_2T_EN | SDRAM_CFG_HSE |\
  90                                          SDRAM_CFG_DBW_32 |\
  91                                          SDRAM_CFG_SDRAM_TYPE_DDR2)
  92
  93 #define CONFIG_SYS_SDRAM_CFG2           0x00401000
  94 #define CONFIG_SYS_DDR_MODE             ((0x0448 << SDRAM_MODE_ESD_SHIFT) |\
  95                                          (0x0242 << SDRAM_MODE_SD_SHIFT))
  96 #define CONFIG_SYS_DDR_MODE_2           0x00000000
  97 #define CONFIG_SYS_DDR_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_075
  98 #define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN |\
  99                                          DDRCDR_PZ_NOMZ |\
 100                                          DDRCDR_NZ_NOMZ |\
 101                                          DDRCDR_ODT |\
 102                                          DDRCDR_M_ODR |\
 103                                          DDRCDR_Q_DRN)
 104
 105 /*
 106  * on-board devices
 107  */
 108 #define CONFIG_TSEC1
 109 #define CONFIG_TSEC2
 110
 111 /*
 112  * NOR FLASH setup
 113  */
 114 #define CONFIG_SYS_FLASH_CFI_WIDTH      FLASH_CFI_8BIT
 115 #define CONFIG_FLASH_SHOW_PROGRESS      50
 116
 117 #define CONFIG_SYS_FLASH_BASE           0xFF800000
 118 #define CONFIG_SYS_FLASH_SIZE           8
 119
 120
 121 #define CONFIG_SYS_MAX_FLASH_BANKS      1
 122 #define CONFIG_SYS_MAX_FLASH_SECT       128
 123
 124 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000
 125 #define CONFIG_SYS_FLASH_WRITE_TOUT     500
 126
 127 /*
 128  * NAND FLASH setup
 129  */
 130 #define CONFIG_SYS_NAND_BASE            0xE1000000
 131 #define CONFIG_SYS_MAX_NAND_DEVICE      1
 132 #define CONFIG_SYS_NAND_MAX_CHIPS       1
 133 #define CONFIG_NAND_FSL_ELBC
 134 #define CONFIG_SYS_NAND_PAGE_SIZE       (2048)
 135 #define CONFIG_SYS_NAND_BLOCK_SIZE      (128 << 10)
 136 #define NAND_CACHE_PAGES                64
 137
 138
 139 /*
 140  * MRAM setup
 141  */
 142 #define CONFIG_SYS_MRAM_BASE            0xE2000000
 143 #define CONFIG_SYS_MRAM_SIZE            0x20000 /* 128 Kb */
 144
 145 #define CONFIG_SYS_OR_TIMING_MRAM
 146
 147
 148 /*
 149  * CPLD setup
 150  */
 151 #define CONFIG_SYS_CPLD_BASE            0xE3000000
 152 #define CONFIG_SYS_CPLD_SIZE            0x8000
 153
 154 #define CONFIG_SYS_OR_TIMING_MRAM
 155
 156
 157 /*
 158  * HW-Watchdog
 159  */
 160 #define CONFIG_WATCHDOG         1
 161 #define CONFIG_SYS_WATCHDOG_VALUE       0xFFFF
 162
 163 /*
 164  * I2C setup
 165  */
 166 #define CONFIG_SYS_I2C
 167 #define CONFIG_SYS_I2C_FSL
 168 #define CONFIG_SYS_FSL_I2C_SPEED        400000
 169 #define CONFIG_SYS_FSL_I2C_SLAVE        0x7F
 170 #define CONFIG_SYS_FSL_I2C_OFFSET       0x3100
 171 #define CONFIG_SYS_I2C_RTC_ADDR 0x51
 172
 173 /*
 174  * Ethernet setup
 175  */
 176 #ifdef CONFIG_TSEC1
 177 #define CONFIG_HAS_ETH0
 178 #define CONFIG_TSEC1_NAME               "TSEC0"
 179 #define CONFIG_SYS_TSEC1_OFFSET 0x24000
 180 #define TSEC1_PHY_ADDR                  0x1
 181 #define TSEC1_FLAGS                     TSEC_GIGABIT
 182 #define TSEC1_PHYIDX                    0
 183 #endif
 184
 185 #ifdef CONFIG_TSEC2
 186 #define CONFIG_HAS_ETH1
 187 #define CONFIG_TSEC2_NAME               "TSEC1"
 188 #define CONFIG_SYS_TSEC2_OFFSET 0x25000
 189 #define TSEC2_PHY_ADDR                  0x3
 190 #define TSEC2_FLAGS                     TSEC_GIGABIT
 191 #define TSEC2_PHYIDX                    0
 192 #endif
 193 #define CONFIG_ETHPRIME         "TSEC1"
 194
 195 /*
 196  * Serial Port
 197  */
 198 #define CONFIG_SYS_NS16550_SERIAL
 199 #define CONFIG_SYS_NS16550_REG_SIZE     1
 200
 201 #define CONFIG_SYS_BAUDRATE_TABLE       \
 202         {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
 203 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x4500)
 204 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x4600)
 205 #define CONFIG_SYS_NS16550_CLK          (get_bus_freq(0))
 206
 207 #define CONFIG_HAS_FSL_DR_USB
 208 #define CONFIG_SYS_SCCR_USBDRCM 3
 209
 210 /*
 211  * U-Boot environment setup
 212  */
 213 #define CONFIG_BOOTP_BOOTFILESIZE
 214
 215 /*
 216  * The reserved memory
 217  */
 218 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
 219 #define CONFIG_SYS_MONITOR_LEN          (768 * 1024)
 220 #define CONFIG_SYS_MALLOC_LEN           (8 * 1024 * 1024)
 221
 222 /*
 223  * Environment Configuration
 224  */
 225
 226 #define CONFIG_NETDEV                   eth1
 227 #define CONFIG_HOSTNAME         "ids8313"
 228 #define CONFIG_ROOTPATH         "/opt/eldk-4.2/ppc_6xx"
 229 #define CONFIG_BOOTFILE         "ids8313/uImage"
 230 #define CONFIG_UBOOTPATH                "ids8313/u-boot.bin"
 231 #define CONFIG_FDTFILE                  "ids8313/ids8313.dtb"
 232 #define CONFIG_LOADADDR         0x400000
 233 #define CONFIG_ENV_FLAGS_LIST_STATIC "ethaddr:mo,eth1addr:mo"
 234
 235 /* Initial Memory map for Linux*/
 236 #define CONFIG_SYS_BOOTMAPSZ            (256 << 20)
 237
 238 /*
 239  * Miscellaneous configurable options
 240  */
 241 #define CONFIG_SYS_CBSIZE               1024
 242 #define CONFIG_SYS_BARGSIZE             CONFIG_SYS_CBSIZE
 243
 244 #define CONFIG_SYS_LOAD_ADDR            0x100000
 245 #define CONFIG_LOADS_ECHO
 246 #define CONFIG_TIMESTAMP
 247 #define CONFIG_BOOTCOMMAND              "run boot_cramfs"
 248 #undef  CONFIG_SYS_LOADS_BAUD_CHANGE
 249
 250 #define CONFIG_JFFS2_NAND
 251 #define CONFIG_JFFS2_DEV                "0"
 252
 253 /* mtdparts command line support */
 254
 255 #define CONFIG_EXTRA_ENV_SETTINGS \
 256         "netdev=" __stringify(CONFIG_NETDEV) "\0"                       \
 257         "ethprime=TSEC1\0"                                              \
 258         "uboot=" __stringify(CONFIG_UBOOTPATH) "\0"                     \
 259         "tftpflash=tftpboot ${loadaddr} ${uboot}; "                     \
 260                 "protect off " __stringify(CONFIG_SYS_TEXT_BASE)        \
 261                 " +${filesize}; "                                       \
 262                 "erase " __stringify(CONFIG_SYS_TEXT_BASE)              \
 263                 " +${filesize}; "                                       \
 264                 "cp.b ${loadaddr} " __stringify(CONFIG_SYS_TEXT_BASE)   \
 265                 " ${filesize}; "                                        \
 266                 "protect on " __stringify(CONFIG_SYS_TEXT_BASE)         \
 267                 " +${filesize}; "                                       \
 268                 "cmp.b ${loadaddr} " __stringify(CONFIG_SYS_TEXT_BASE)  \
 269                 " ${filesize}\0"                                        \
 270         "console=ttyS0\0"                                               \
 271         "fdtaddr=0x780000\0"                                            \
 272         "kernel_addr=ff800000\0"                                        \
 273         "fdtfile=" __stringify(CONFIG_FDTFILE) "\0"                     \
 274         "setbootargs=setenv bootargs "                                  \
 275                 "root=${rootdev} rw console=${console},"                \
 276                         "${baudrate} ${othbootargs}\0"                  \
 277         "setipargs=setenv bootargs root=${rootdev} rw "                 \
 278                         "nfsroot=${serverip}:${rootpath} "              \
 279                         "ip=${ipaddr}:${serverip}:${gatewayip}:"        \
 280                         "${netmask}:${hostname}:${netdev}:off "         \
 281                         "console=${console},${baudrate} ${othbootargs}\0" \
 282         "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0"              \
 283         "mtdids=" CONFIG_MTDIDS_DEFAULT "\0"                                    \
 284         "mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0"                                \
 285         "\0"
 286
 287 #define CONFIG_NFSBOOTCOMMAND                                           \
 288         "setenv rootdev /dev/nfs;"                                      \
 289         "run setipargs;run addmtd;"                                     \
 290         "tftp ${loadaddr} ${bootfile};"                         \
 291         "tftp ${fdtaddr} ${fdtfile};"                                   \
 292         "fdt addr ${fdtaddr};"                                          \
 293         "bootm ${loadaddr} - ${fdtaddr}"
 294
 295 /* UBI Support */
 296
 297 #endif  /* __CONFIG_H */