include/configs/ge_b1x5v2.h

   1 /*
   2  * GE B1x5v2
   3  *
   4  * Copyright 2018-2020 GE Inc.
   5  * Copyright 2018-2020 Collabora Ltd.
   6  *
   7  * SPDX-License-Identifier:    GPL-2.0+
   8  */
   9
  10 #ifndef __GE_B1X5V2_CONFIG_H
  11 #define __GE_B1X5V2_CONFIG_H
  12
  13 #include "mx6_common.h"
  14
  15 #include "imx6_spl.h"
  16
  17 /* PWM */
  18 #define CONFIG_IMX6_PWM_PER_CLK         66000000
  19
  20 /* UART */
  21 #define CONFIG_MXC_UART_BASE            UART3_BASE
  22
  23 #if CONFIG_MXC_UART_BASE == UART2_BASE
  24 /* UART2 requires CONFIG_DEBUG_UART_BASE=0x21e8000 */
  25 #define CONSOLE_DEVICE "ttymxc1" /* System on Module debug connector */
  26 #else
  27 /* UART3 requires CONFIG_DEBUG_UART_BASE=0x21ec000 */
  28 #define CONSOLE_DEVICE "ttymxc2" /* Base board debug connector */
  29 #endif
  30
  31 /* USB */
  32 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
  33 #define CONFIG_MXC_USB_PORTSC           (PORT_PTS_UTMI | PORT_PTS_PTW)
  34 #define CONFIG_MXC_USB_FLAGS            0
  35 #define CONFIG_USB_MAX_CONTROLLER_COUNT 2 /* Enabled USB controller number */
  36 #define CONFIG_USBD_HS
  37
  38 /* Video */
  39 #define CONFIG_HIDE_LOGO_VERSION
  40 #define CONFIG_IMX_VIDEO_SKIP
  41
  42 /* Memory */
  43 #define PHYS_SDRAM                     MMDC0_ARB_BASE_ADDR
  44
  45 #define CONFIG_SYS_SDRAM_BASE          PHYS_SDRAM
  46 #define CONFIG_SYS_INIT_RAM_ADDR       IRAM_BASE_ADDR
  47 #define CONFIG_SYS_INIT_RAM_SIZE       IRAM_SIZE
  48
  49 /* Command definition */
  50 #define CONFIG_EXTRA_ENV_SETTINGS \
  51         "image=/boot/fitImage\0" \
  52         "fdt_addr_r=0x18000000\0" \
  53         "splash_addr_r=0x20000000\0" \
  54         "mmcdev=2\0" \
  55         "mmcpart=1\0" \
  56         "console=console="CONSOLE_DEVICE",115200\0" \
  57         "quiet=quiet loglevel=0\0" \
  58         "rootdev=/dev/mmcblk1p\0" \
  59         "setargs=setenv bootargs ${console} ${quiet} ${fsckforcerepair} " \
  60                 "bootcause=${bootcause} vt.global_cursor_default=0 vt.cur_default=1 " \
  61                 "root=${rootdev}${mmcpart} video=HDMI-A-1:${resolution} rootwait ro\0" \
  62         "loadimage=load mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
  63         "showsplashscreen=load mmc ${mmcdev}:${mmcpart} ${splash_addr_r} /boot/splashscreen-${resolution}.bmp; " \
  64                 "bmp display ${splash_addr_r};\0" \
  65         "setconfidx=" \
  66                 "if test \"${devicetype}\" = \"B105v2\"; then " \
  67                         "setenv confidx 1; " \
  68                 "elif test \"${devicetype}\" = \"B125v2\"; then " \
  69                         "setenv confidx 2; " \
  70                 "elif test \"${devicetype}\" = \"B155v2\"; then " \
  71                         "setenv confidx 3; " \
  72                 "elif test \"${devicetype}\" = \"B105Pv2\"; then " \
  73                         "setenv confidx 4; " \
  74                 "elif test \"${devicetype}\" = \"B125Pv2\"; then " \
  75                         "setenv confidx 5; " \
  76                 "fi;\0" \
  77         "set_default_type=setenv devicetype B155v2; setenv resolution 1366x768;" \
  78                 "setenv fdtfile imx6dl-b155v2.dtb; run setconfidx;\0" \
  79         "checkconfidx=env exists confidx || run set_default_type;\0" \
  80         "checkfsckforcerepair=" \
  81                 "if test \"${bootcount}\" > \"3\" ; then " \
  82                         "setenv fsckforcerepair fsck.repair=1; " \
  83                 "fi;\0" \
  84         "helix=run setconfidx; run checkconfidx; run checkfsckforcerepair; run setargs; " \
  85                 "regulator dev LED_VCC; regulator enable; " \
  86                 "regulator dev 5V0_AUDIO; regulator enable; " \
  87                 "bootm ${loadaddr}#conf@${confidx};\0" \
  88         "failbootcmd=" \
  89                 "echo reached failbootcmd;" \
  90                 "cls; setcurs 5 4; " \
  91                 "lcdputs \"Monitor failed to start. Try again, or contact GE Service for support.\"; " \
  92                 "bootcount reset; \0" \
  93         "hasfirstboot=" \
  94                 "load mmc ${mmcdev}:${mmcpart} ${loadaddr} " \
  95                 "/boot/bootcause/firstboot;\0" \
  96         "swappartitions=" \
  97                 "setexpr mmcpart 3 - ${mmcpart};\0" \
  98         "doboot=" \
  99                 "echo Booting from mmc:${mmcdev}:${mmcpart} ...; " \
 100                 "run helix;\0" \
 101         "altbootcmd=" \
 102                 "setenv mmcpart 1; run hasfirstboot || setenv mmcpart 2; " \
 103                 "run hasfirstboot || setenv mmcpart 0; " \
 104                 "if test ${mmcpart} != 0; then " \
 105                         "setenv bootcause REVERT; " \
 106                         "run swappartitions loadimage doboot; " \
 107                 "fi; " \
 108                 "run failbootcmd\0" \
 109         "tryboot=" \
 110                 "setenv mmcpart 1; run hasfirstboot || setenv mmcpart 2; " \
 111                 "run loadimage || run swappartitions && run loadimage || " \
 112                 "setenv mmcpart 0 && echo MISSING IMAGE;" \
 113                 "run showsplashscreen; sleep 1; " \
 114                 "run doboot; run failbootcmd;\0" \
 115
 116 #endif /* __GE_B1X5V2_CONFIG_H */