include/configs/flea3.h

   1 /*
   2  * (C) Copyright 2011, Stefano Babic <sbabic@denx.de>
   3  *
   4  * (C) Copyright 2008-2010 Freescale Semiconductor, Inc.
   5  *
   6  * Copyright (C) 2007, Guennadi Liakhovetski <lg@denx.de>
   7  *
   8  * Configuration for the flea3 board.
   9  *
  10  * SPDX-License-Identifier:     GPL-2.0+
  11  */
  12
  13 #ifndef __CONFIG_H
  14 #define __CONFIG_H
  15
  16 #include <asm/arch/imx-regs.h>
  17
  18  /* High Level Configuration Options */
  19 #define CONFIG_MX35
  20
  21 #define CONFIG_SYS_DCACHE_OFF
  22 #define CONFIG_SYS_CACHELINE_SIZE       32
  23
  24 #define CONFIG_DISPLAY_CPUINFO
  25 #define CONFIG_SYS_GENERIC_BOARD
  26
  27 /* Only in case the value is not present in mach-types.h */
  28 #ifndef MACH_TYPE_FLEA3
  29 #define MACH_TYPE_FLEA3                3668
  30 #endif
  31
  32 #define CONFIG_MACH_TYPE                MACH_TYPE_FLEA3
  33
  34 /* Set TEXT at the beginning of the NOR flash */
  35 #define CONFIG_SYS_TEXT_BASE    0xA0000000
  36
  37 /* This is required to setup the ESDC controller */
  38 #define CONFIG_BOARD_EARLY_INIT_F
  39
  40 #define CONFIG_CMDLINE_TAG              /* enable passing of ATAGs */
  41 #define CONFIG_REVISION_TAG
  42 #define CONFIG_SETUP_MEMORY_TAGS
  43 #define CONFIG_INITRD_TAG
  44
  45 /*
  46  * Size of malloc() pool
  47  */
  48 #define CONFIG_SYS_MALLOC_LEN           (CONFIG_ENV_SIZE + 1024 * 1024)
  49
  50 /*
  51  * Hardware drivers
  52  */
  53 #define CONFIG_SYS_I2C
  54 #define CONFIG_SYS_I2C_MXC
  55 #define CONFIG_SYS_I2C_MXC_I2C1         /* enable I2C bus 1 */
  56 #define CONFIG_SYS_I2C_MXC_I2C2         /* enable I2C bus 2 */
  57 #define CONFIG_SYS_I2C_MXC_I2C3         /* enable I2C bus 3 */
  58 #define CONFIG_SYS_SPD_BUS_NUM          2 /* I2C3 */
  59 #define CONFIG_SYS_MXC_I2C3_SLAVE       0xfe
  60 #define CONFIG_MXC_SPI
  61 #define CONFIG_MXC_GPIO
  62
  63 /*
  64  * UART (console)
  65  */
  66 #define CONFIG_MXC_UART
  67 #define CONFIG_MXC_UART_BASE    UART3_BASE
  68
  69 /* allow to overwrite serial and ethaddr */
  70 #define CONFIG_ENV_OVERWRITE
  71 #define CONFIG_CONS_INDEX       1
  72 #define CONFIG_BAUDRATE         115200
  73
  74 /*
  75  * Command definition
  76  */
  77 #define CONFIG_CMD_PING
  78 #define CONFIG_CMD_DHCP
  79 #define CONFIG_BOOTP_SUBNETMASK
  80 #define CONFIG_BOOTP_GATEWAY
  81 #define CONFIG_BOOTP_DNS
  82
  83 #define CONFIG_CMD_NAND
  84 #define CONFIG_CMD_CACHE
  85
  86 #define CONFIG_CMD_I2C
  87 #define CONFIG_CMD_SPI
  88 #define CONFIG_CMD_MII
  89 #define CONFIG_NET_RETRY_COUNT  100
  90
  91 #define CONFIG_BOOTDELAY        3
  92
  93 #define CONFIG_LOADADDR         0x80800000      /* loadaddr env var */
  94
  95
  96 /*
  97  * Ethernet on SOC (FEC)
  98  */
  99 #define CONFIG_FEC_MXC
 100 #define IMX_FEC_BASE    FEC_BASE_ADDR
 101 #define CONFIG_PHYLIB
 102 #define CONFIG_PHY_MICREL
 103 #define CONFIG_FEC_MXC_PHYADDR  0x1
 104
 105 #define CONFIG_MII
 106
 107 #define CONFIG_ARP_TIMEOUT      200UL
 108
 109 /*
 110  * Miscellaneous configurable options
 111  */
 112 #define CONFIG_SYS_LONGHELP     /* undef to save memory */
 113 #define CONFIG_CMDLINE_EDITING
 114 #define CONFIG_SYS_HUSH_PARSER  /* Use the HUSH parser */
 115
 116 #define CONFIG_AUTO_COMPLETE
 117 #define CONFIG_SYS_CBSIZE       256     /* Console I/O Buffer Size */
 118 /* Print Buffer Size */
 119 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
 120 #define CONFIG_SYS_MAXARGS      16      /* max number of command args */
 121 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
 122
 123 #define CONFIG_SYS_MEMTEST_START        0       /* memtest works on */
 124 #define CONFIG_SYS_MEMTEST_END          0x10000
 125
 126 #define CONFIG_SYS_LOAD_ADDR            CONFIG_LOADADDR
 127
 128 /*
 129  * Physical Memory Map
 130  */
 131 #define CONFIG_NR_DRAM_BANKS    1
 132 #define PHYS_SDRAM_1            CSD0_BASE_ADDR
 133 #define PHYS_SDRAM_1_SIZE       (128 * 1024 * 1024)
 134
 135 #define CONFIG_SYS_SDRAM_BASE           CSD0_BASE_ADDR
 136 #define CONFIG_SYS_INIT_RAM_ADDR        (IRAM_BASE_ADDR + 0x10000)
 137 #define CONFIG_SYS_INIT_RAM_SIZE                (IRAM_SIZE / 2)
 138 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - \
 139                                         GENERATED_GBL_DATA_SIZE)
 140 #define CONFIG_SYS_INIT_SP_ADDR         (CONFIG_SYS_INIT_RAM_ADDR + \
 141                                         CONFIG_SYS_GBL_DATA_OFFSET)
 142
 143 /*
 144  * MTD Command for mtdparts
 145  */
 146 #define CONFIG_CMD_MTDPARTS
 147 #define CONFIG_MTD_DEVICE
 148 #define CONFIG_FLASH_CFI_MTD
 149 #define CONFIG_MTD_PARTITIONS
 150 #define MTDIDS_DEFAULT          "nand0=mxc_nand,nor0=physmap-flash.0"
 151 #define MTDPARTS_DEFAULT        "mtdparts=mxc_nand:50m(root1)," \
 152                                 "32m(rootfb)," \
 153                                 "64m(pcache)," \
 154                                 "64m(app1)," \
 155                                 "10m(app2),-(spool);" \
 156                                 "physmap-flash.0:512k(u-boot),64k(env1)," \
 157                                 "64k(env2),3776k(kernel1),3776k(kernel2)"
 158
 159 /*
 160  * FLASH and environment organization
 161  */
 162 #define CONFIG_SYS_FLASH_BASE           CS0_BASE_ADDR
 163 #define CONFIG_SYS_MAX_FLASH_BANKS 1    /* max number of memory banks */
 164 #define CONFIG_SYS_MAX_FLASH_SECT 512   /* max number of sectors on one chip */
 165 /* Monitor at beginning of flash */
 166 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
 167 #define CONFIG_SYS_MONITOR_LEN          (512 * 1024)
 168
 169 #define CONFIG_ENV_SECT_SIZE    (64 * 1024)
 170 #define CONFIG_ENV_SIZE         CONFIG_ENV_SECT_SIZE
 171
 172 /* Address and size of Redundant Environment Sector     */
 173 #define CONFIG_ENV_OFFSET_REDUND        (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
 174 #define CONFIG_ENV_SIZE_REDUND  CONFIG_ENV_SIZE
 175
 176 #define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE + \
 177                                 CONFIG_SYS_MONITOR_LEN)
 178
 179 #define CONFIG_ENV_IS_IN_FLASH
 180
 181 /*
 182  * CFI FLASH driver setup
 183  */
 184 #define CONFIG_SYS_FLASH_CFI            /* Flash memory is CFI compliant */
 185 #define CONFIG_FLASH_CFI_DRIVER
 186
 187 /* A non-standard buffered write algorithm */
 188 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE       /* faster */
 189 #define CONFIG_SYS_FLASH_PROTECTION     /* Use hardware sector protection */
 190
 191 /*
 192  * NAND FLASH driver setup
 193  */
 194 #define CONFIG_NAND_MXC
 195 #define CONFIG_MXC_NAND_REGS_BASE       (NFC_BASE_ADDR)
 196 #define CONFIG_SYS_MAX_NAND_DEVICE      1
 197 #define CONFIG_SYS_NAND_BASE            (NFC_BASE_ADDR)
 198 #define CONFIG_MXC_NAND_HWECC
 199 #define CONFIG_SYS_NAND_LARGEPAGE
 200
 201 /*
 202  * Default environment and default scripts
 203  * to update uboot and load kernel
 204  */
 205
 206 #define CONFIG_HOSTNAME flea3
 207 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
 208         "netdev=eth0\0"                                                 \
 209         "nfsargs=setenv bootargs root=/dev/nfs rw "                     \
 210                 "nfsroot=${serverip}:${rootpath}\0"                     \
 211         "ramargs=setenv bootargs root=/dev/ram rw\0"                    \
 212         "addip_sta=setenv bootargs ${bootargs} "                        \
 213                 "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"      \
 214                 ":${hostname}:${netdev}:off panic=1\0"                  \
 215         "addip_dyn=setenv bootargs ${bootargs} ip=dhcp\0"               \
 216         "addip=if test -n ${ipdyn};then run addip_dyn;"                 \
 217                 "else run addip_sta;fi\0"                               \
 218         "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0"              \
 219         "addtty=setenv bootargs ${bootargs}"                            \
 220                 " console=ttymxc2,${baudrate}\0"                        \
 221         "addmisc=setenv bootargs ${bootargs} ${misc}\0"                 \
 222         "loadaddr=80800000\0"                                           \
 223         "kernel_addr_r=80800000\0"                                      \
 224         "hostname=" __stringify(CONFIG_HOSTNAME) "\0"                   \
 225         "bootfile=" __stringify(CONFIG_HOSTNAME) "/uImage\0"            \
 226         "ramdisk_file=" __stringify(CONFIG_HOSTNAME) "/uRamdisk\0"      \
 227         "flash_self=run ramargs addip addtty addmtd addmisc;"           \
 228                 "bootm ${kernel_addr} ${ramdisk_addr}\0"                \
 229         "flash_nfs=run nfsargs addip addtty addmtd addmisc;"            \
 230                 "bootm ${kernel_addr}\0"                                \
 231         "net_nfs=tftp ${kernel_addr_r} ${bootfile}; "                   \
 232                 "run nfsargs addip addtty addmtd addmisc;"              \
 233                 "bootm ${kernel_addr_r}\0"                              \
 234         "net_self_load=tftp ${kernel_addr_r} ${bootfile};"              \
 235                 "tftp ${ramdisk_addr_r} ${ramdisk_file};\0"             \
 236         "net_self=if run net_self_load;then "                           \
 237                 "run ramargs addip addtty addmtd addmisc;"              \
 238                 "bootm ${kernel_addr_r} ${ramdisk_addr_r};"             \
 239                 "else echo Images not loades;fi\0"                      \
 240         "u-boot=" __stringify(CONFIG_HOSTNAME) "/u-boot.bin\0"          \
 241         "load=tftp ${loadaddr} ${u-boot}\0"                             \
 242         "uboot_addr=" __stringify(CONFIG_SYS_MONITOR_BASE) "\0"         \
 243         "update=protect off ${uboot_addr} +40000;"                      \
 244                 "erase ${uboot_addr} +40000;"                           \
 245                 "cp.b ${loadaddr} ${uboot_addr} ${filesize}\0"          \
 246         "upd=if run load;then echo Updating u-boot;if run update;"      \
 247                 "then echo U-Boot updated;"                             \
 248                         "else echo Error updating u-boot !;"            \
 249                         "echo Board without bootloader !!;"             \
 250                 "fi;"                                                   \
 251                 "else echo U-Boot not downloaded..exiting;fi\0"         \
 252         "bootcmd=run net_nfs\0"
 253
 254 #endif                          /* __CONFIG_H */