1 /* SPDX-License-Identifier: GPL-2.0+ */
3 * Copyright (C) 2010 Albert ARIBAUD <albert.u.boot@aribaud.net>
5 * Based on original Kirkwood support which is
7 * Marvell Semiconductor <www.marvell.com>
8 * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
11 #ifndef _CONFIG_EDMINIV2_H
12 #define _CONFIG_EDMINIV2_H
18 #define CONFIG_SPL_STACK 0x00020000
19 #define CONFIG_SPL_BSS_START_ADDR 0x00020000
20 #define CONFIG_SYS_SPL_MALLOC_START 0x00040000
21 #define CONFIG_SYS_SPL_MALLOC_SIZE 0x0001ffff
22 #define CONFIG_SYS_UBOOT_BASE 0xfff90000
23 #define CONFIG_SYS_UBOOT_START 0x00800000
26 * High Level Configuration Options (easy to change)
29 #include <asm/arch/orion5x.h>
35 * Board-specific values for Orion5x MPP low level init:
36 * - MPPs 12 to 15 are SATA LEDs (mode 5)
37 * - Others are GPIO/unused (mode 3 for MPP0, mode 5 for
38 * MPP16 to MPP19, mode 0 for others
41 #define ORION5X_MPP0_7 0x00000003
42 #define ORION5X_MPP8_15 0x55550000
43 #define ORION5X_MPP16_23 0x00005555
46 * Board-specific values for Orion5x GPIO low level init:
47 * - GPIO3 is input (RTC interrupt)
48 * - GPIO16 is Power LED control (0 = on, 1 = off)
49 * - GPIO17 is Power LED source select (0 = CPLD, 1 = GPIO16)
50 * - GPIO18 is Power Button status (0 = Released, 1 = Pressed)
51 * - GPIO19 is SATA disk power toggle (toggles on 0-to-1)
52 * - GPIO22 is SATA disk power status ()
53 * - GPIO23 is supply status for SATA disk ()
54 * - GPIO24 is supply control for board (write 1 to power off)
55 * Last GPIO is 25, further bits are supposed to be 0.
56 * Enable mask has ones for INPUT, 0 for OUTPUT.
57 * Default is LED ON, board ON :)
60 #define ORION5X_GPIO_OUT_ENABLE 0xfef4f0ca
61 #define ORION5X_GPIO_OUT_VALUE 0x00000000
62 #define ORION5X_GPIO_IN_POLARITY 0x000000d0
65 * NS16550 Configuration
68 #define CONFIG_SYS_NS16550_SERIAL
69 #define CONFIG_SYS_NS16550_REG_SIZE (-4)
70 #define CONFIG_SYS_NS16550_CLK CONFIG_SYS_TCLK
71 #define CONFIG_SYS_NS16550_COM1 ORION5X_UART0_BASE
74 * Serial Port configuration
75 * The following definitions let you select what serial you want to use
76 * for your console driver.
79 #define CONFIG_SYS_BAUDRATE_TABLE \
80 { 9600, 19200, 38400, 57600, 115200, 230400, 460800, 921600 }
86 #define CONFIG_SYS_MAX_FLASH_SECT 11 /* max num of sects on one chip */
87 #define CONFIG_SYS_FLASH_BASE 0xfff80000
96 #define CONFIG_MVGBE_PORTS {1} /* enable port 0 only */
97 #define CONFIG_SKIP_LOCAL_MAC_RANDOMIZATION /* don't randomize MAC */
98 #define CONFIG_PHY_BASE_ADR 0x8
106 /* Data, registers and alternate blocks are at the same offset */
107 /* Each 8-bit ATA register is aligned to a 4-bytes address */
108 /* Controller supports 48-bits LBA addressing */
110 /* A single bus, a single device */
111 /* ATA registers base is at SATA controller base */
112 /* ATA bus 0 is orion5x port 1 on ED Mini V2 */
113 /* end of IDE defines */
117 * Common USB/EHCI configuration
119 #ifdef CONFIG_CMD_USB
120 #define ORION5X_USB20_HOST_PORT_BASE ORION5X_USB20_PORT0_BASE
121 #endif /* CONFIG_CMD_USB */
126 #ifdef CONFIG_CMD_I2C
127 #define CONFIG_I2C_MVTWSI_BASE0 ORION5X_TWSI_BASE
131 * Environment variables configurations
134 /* Enable command line editing */
136 /* provide extensive help */
138 /* additions for new relocation code, must be added to all boards */
139 #define CONFIG_SYS_SDRAM_BASE 0
141 #endif /* _CONFIG_EDMINIV2_H */