1 /* SPDX-License-Identifier: GPL-2.0+ */
3 * Copyright (C) 2010 Albert ARIBAUD <albert.u.boot@aribaud.net>
5 * Based on original Kirkwood support which is
7 * Marvell Semiconductor <www.marvell.com>
8 * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
11 #ifndef _CONFIG_EDMINIV2_H
12 #define _CONFIG_EDMINIV2_H
18 #define CONFIG_SYS_UBOOT_BASE 0xfff90000
19 #define CONFIG_SYS_UBOOT_START 0x00800000
22 * High Level Configuration Options (easy to change)
25 #include <asm/arch/orion5x.h>
31 * Board-specific values for Orion5x MPP low level init:
32 * - MPPs 12 to 15 are SATA LEDs (mode 5)
33 * - Others are GPIO/unused (mode 3 for MPP0, mode 5 for
34 * MPP16 to MPP19, mode 0 for others
37 #define ORION5X_MPP0_7 0x00000003
38 #define ORION5X_MPP8_15 0x55550000
39 #define ORION5X_MPP16_23 0x00005555
42 * Board-specific values for Orion5x GPIO low level init:
43 * - GPIO3 is input (RTC interrupt)
44 * - GPIO16 is Power LED control (0 = on, 1 = off)
45 * - GPIO17 is Power LED source select (0 = CPLD, 1 = GPIO16)
46 * - GPIO18 is Power Button status (0 = Released, 1 = Pressed)
47 * - GPIO19 is SATA disk power toggle (toggles on 0-to-1)
48 * - GPIO22 is SATA disk power status ()
49 * - GPIO23 is supply status for SATA disk ()
50 * - GPIO24 is supply control for board (write 1 to power off)
51 * Last GPIO is 25, further bits are supposed to be 0.
52 * Enable mask has ones for INPUT, 0 for OUTPUT.
53 * Default is LED ON, board ON :)
56 #define ORION5X_GPIO_OUT_ENABLE 0xfef4f0ca
57 #define ORION5X_GPIO_OUT_VALUE 0x00000000
58 #define ORION5X_GPIO_IN_POLARITY 0x000000d0
61 * NS16550 Configuration
64 #define CONFIG_SYS_NS16550_SERIAL
65 #define CONFIG_SYS_NS16550_REG_SIZE (-4)
66 #define CONFIG_SYS_NS16550_CLK CONFIG_SYS_TCLK
67 #define CONFIG_SYS_NS16550_COM1 ORION5X_UART0_BASE
70 * Serial Port configuration
71 * The following definitions let you select what serial you want to use
72 * for your console driver.
75 #define CONFIG_SYS_BAUDRATE_TABLE \
76 { 9600, 19200, 38400, 57600, 115200, 230400, 460800, 921600 }
82 #define CONFIG_SYS_FLASH_BASE 0xfff80000
91 #define CONFIG_MVGBE_PORTS {1} /* enable port 0 only */
92 #define CONFIG_SKIP_LOCAL_MAC_RANDOMIZATION /* don't randomize MAC */
93 #define CONFIG_PHY_BASE_ADR 0x8
101 /* Data, registers and alternate blocks are at the same offset */
102 /* Each 8-bit ATA register is aligned to a 4-bytes address */
103 /* A single bus, a single device */
104 /* ATA registers base is at SATA controller base */
105 /* ATA bus 0 is orion5x port 1 on ED Mini V2 */
106 /* end of IDE defines */
110 * Common USB/EHCI configuration
112 #ifdef CONFIG_CMD_USB
113 #define ORION5X_USB20_HOST_PORT_BASE ORION5X_USB20_PORT0_BASE
114 #endif /* CONFIG_CMD_USB */
119 #ifdef CONFIG_CMD_I2C
120 #define CONFIG_I2C_MVTWSI_BASE0 ORION5X_TWSI_BASE
124 * Environment variables configurations
127 /* Enable command line editing */
129 /* provide extensive help */
131 /* additions for new relocation code, must be added to all boards */
132 #define CONFIG_SYS_SDRAM_BASE 0
134 #endif /* _CONFIG_EDMINIV2_H */