include/configs/dra7xx_evm.h

   1 /*
   2  * (C) Copyright 2013
   3  * Texas Instruments Incorporated.
   4  * Lokesh Vutla   <lokeshvutla@ti.com>
   5  *
   6  * Configuration settings for the TI DRA7XX board.
   7  * See ti_omap5_common.h for omap5 common settings.
   8  *
   9  * SPDX-License-Identifier:     GPL-2.0+
  10  */
  11
  12 #ifndef __CONFIG_DRA7XX_EVM_H
  13 #define __CONFIG_DRA7XX_EVM_H
  14
  15 #define CONFIG_DRA7XX
  16 #define CONFIG_BOARD_EARLY_INIT_F
  17
  18 #ifndef CONFIG_QSPI_BOOT
  19 /* MMC ENV related defines */
  20 #define CONFIG_ENV_IS_IN_MMC
  21 #define CONFIG_SYS_MMC_ENV_DEV          1       /* SLOT2: eMMC(1) */
  22 #define CONFIG_ENV_SIZE                 (128 << 10)
  23 #define CONFIG_ENV_OFFSET               0xE0000
  24 #define CONFIG_ENV_OFFSET_REDUND        (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
  25 #define CONFIG_SYS_REDUNDAND_ENVIRONMENT
  26 #endif
  27 #define CONFIG_CMD_SAVEENV
  28
  29 #if (CONFIG_CONS_INDEX == 1)
  30 #define CONSOLEDEV                      "ttyO0"
  31 #elif (CONFIG_CONS_INDEX == 3)
  32 #define CONSOLEDEV                      "ttyO2"
  33 #endif
  34 #define CONFIG_SYS_NS16550_COM1         UART1_BASE      /* Base EVM has UART0 */
  35 #define CONFIG_SYS_NS16550_COM2         UART2_BASE      /* UART2 */
  36 #define CONFIG_SYS_NS16550_COM3         UART3_BASE      /* UART3 */
  37 #define CONFIG_BAUDRATE                 115200
  38
  39 #define CONFIG_SYS_OMAP_ABE_SYSCK
  40
  41 /* Define the default GPT table for eMMC */
  42 #define PARTS_DEFAULT \
  43         "uuid_disk=${uuid_gpt_disk};" \
  44         "name=rootfs,start=2MiB,size=-,uuid=${uuid_gpt_rootfs}"
  45
  46 #include <configs/ti_omap5_common.h>
  47
  48 /* Enhance our eMMC support / experience. */
  49 #define CONFIG_CMD_GPT
  50 #define CONFIG_EFI_PARTITION
  51 #define CONFIG_HSMMC2_8BIT
  52
  53 /* CPSW Ethernet */
  54 #define CONFIG_CMD_NET                  /* 'bootp' and 'tftp' */
  55 #define CONFIG_CMD_DHCP
  56 #define CONFIG_BOOTP_DNS                /* Configurable parts of CMD_DHCP */
  57 #define CONFIG_BOOTP_DNS2
  58 #define CONFIG_BOOTP_SEND_HOSTNAME
  59 #define CONFIG_BOOTP_GATEWAY
  60 #define CONFIG_BOOTP_SUBNETMASK
  61 #define CONFIG_NET_RETRY_COUNT          10
  62 #define CONFIG_CMD_PING
  63 #define CONFIG_CMD_MII
  64 #define CONFIG_DRIVER_TI_CPSW           /* Driver for IP block */
  65 #define CONFIG_MII                      /* Required in net/eth.c */
  66 #define CONFIG_PHY_GIGE                 /* per-board part of CPSW */
  67 #define CONFIG_PHYLIB
  68
  69 /* SPI */
  70 #undef  CONFIG_OMAP3_SPI
  71 #define CONFIG_TI_QSPI
  72 #define CONFIG_SPI_FLASH
  73 #define CONFIG_SPI_FLASH_SPANSION
  74 #define CONFIG_CMD_SF
  75 #define CONFIG_CMD_SPI
  76 #define CONFIG_SPI_FLASH_BAR
  77 #define CONFIG_TI_SPI_MMAP
  78 #define CONFIG_SF_DEFAULT_SPEED                48000000
  79 #define CONFIG_DEFAULT_SPI_MODE                SPI_MODE_3
  80
  81 /*
  82  * Default to using SPI for environment, etc.
  83  * 0x000000 - 0x010000 : QSPI.SPL (64KiB)
  84  * 0x010000 - 0x020000 : QSPI.SPL.backup1 (64KiB)
  85  * 0x020000 - 0x030000 : QSPI.SPL.backup2 (64KiB)
  86  * 0x030000 - 0x040000 : QSPI.SPL.backup3 (64KiB)
  87  * 0x040000 - 0x140000 : QSPI.u-boot (1MiB)
  88  * 0x140000 - 0x1C0000 : QSPI.u-boot-spl-os (512KiB)
  89  * 0x1C0000 - 0x1D0000 : QSPI.u-boot-env (64KiB)
  90  * 0x1D0000 - 0x1E0000 : QSPI.u-boot-env.backup1 (64KiB)
  91  * 0x1E0000 - 0x9E0000 : QSPI.kernel (8MiB)
  92  * 0x9E0000 - 0x2000000 : USERLAND
  93  */
  94 #define CONFIG_SYS_SPI_KERNEL_OFFS      0x1E0000
  95 #define CONFIG_SYS_SPI_ARGS_OFFS        0x140000
  96 #define CONFIG_SYS_SPI_ARGS_SIZE        0x80000
  97 #if defined(CONFIG_QSPI_BOOT)
  98 /* In SPL, use the environment and discard MMC support for space. */
  99 #ifdef CONFIG_SPL_BUILD
 100 #undef CONFIG_SPL_MMC_SUPPORT
 101 #undef CONFIG_SPL_MAX_SIZE
 102 #define CONFIG_SPL_MAX_SIZE             (64 << 10) /* 64 KiB */
 103 #endif
 104 #define CONFIG_SPL_ENV_SUPPORT
 105 #define CONFIG_ENV_IS_IN_SPI_FLASH
 106 #define CONFIG_SYS_REDUNDAND_ENVIRONMENT
 107 #define CONFIG_ENV_SPI_MAX_HZ           CONFIG_SF_DEFAULT_SPEED
 108 #define CONFIG_ENV_SIZE                 (64 << 10)
 109 #define CONFIG_ENV_SECT_SIZE            (64 << 10) /* 64 KB sectors */
 110 #define CONFIG_ENV_OFFSET               0x1C0000
 111 #define CONFIG_ENV_OFFSET_REDUND        0x1D0000
 112 #endif
 113
 114 /* SPI SPL */
 115 #define CONFIG_SPL_SPI_SUPPORT
 116 #define CONFIG_SPL_SPI_LOAD
 117 #define CONFIG_SPL_SPI_FLASH_SUPPORT
 118 #define CONFIG_SYS_SPI_U_BOOT_OFFS     0x40000
 119
 120 #define CONFIG_SUPPORT_EMMC_BOOT
 121
 122 /* USB xHCI HOST */
 123 #define CONFIG_CMD_USB
 124 #define CONFIG_USB_HOST
 125 #define CONFIG_USB_XHCI
 126 #define CONFIG_USB_XHCI_OMAP
 127 #define CONFIG_USB_STORAGE
 128 #define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS 2
 129
 130 #define CONFIG_OMAP_USB_PHY
 131 #define CONFIG_OMAP_USB2PHY2_HOST
 132
 133 /* SATA */
 134 #define CONFIG_BOARD_LATE_INIT
 135 #define CONFIG_CMD_SCSI
 136 #define CONFIG_LIBATA
 137 #define CONFIG_SCSI_AHCI
 138 #define CONFIG_SCSI_AHCI_PLAT
 139 #define CONFIG_SYS_SCSI_MAX_SCSI_ID     1
 140 #define CONFIG_SYS_SCSI_MAX_LUN         1
 141 #define CONFIG_SYS_SCSI_MAX_DEVICE      (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
 142                                                 CONFIG_SYS_SCSI_MAX_LUN)
 143
 144 /* NAND support */
 145 #ifdef CONFIG_NAND
 146 /* NAND: device related configs */
 147 #define CONFIG_SYS_NAND_PAGE_SIZE       2048
 148 #define CONFIG_SYS_NAND_OOBSIZE         64
 149 #define CONFIG_SYS_NAND_BLOCK_SIZE      (128*1024)
 150 #define CONFIG_SYS_NAND_BUSWIDTH_16BIT
 151 #define CONFIG_SYS_NAND_PAGE_COUNT      (CONFIG_SYS_NAND_BLOCK_SIZE / \
 152                                          CONFIG_SYS_NAND_PAGE_SIZE)
 153 #define CONFIG_SYS_NAND_5_ADDR_CYCLE
 154 /* NAND: driver related configs */
 155 #define CONFIG_NAND_OMAP_GPMC
 156 #define CONFIG_NAND_OMAP_ELM
 157 #define CONFIG_SYS_NAND_ONFI_DETECTION
 158 #define CONFIG_NAND_OMAP_ECCSCHEME      OMAP_ECC_BCH8_CODE_HW
 159 #define CONFIG_SYS_NAND_BAD_BLOCK_POS   NAND_LARGE_BADBLOCK_POS
 160 #define CONFIG_SYS_NAND_ECCPOS          { 2, 3, 4, 5, 6, 7, 8, 9, \
 161                                          10, 11, 12, 13, 14, 15, 16, 17, \
 162                                          18, 19, 20, 21, 22, 23, 24, 25, \
 163                                          26, 27, 28, 29, 30, 31, 32, 33, \
 164                                          34, 35, 36, 37, 38, 39, 40, 41, \
 165                                          42, 43, 44, 45, 46, 47, 48, 49, \
 166                                          50, 51, 52, 53, 54, 55, 56, 57, }
 167 #define CONFIG_SYS_NAND_ECCSIZE         512
 168 #define CONFIG_SYS_NAND_ECCBYTES        14
 169 #define MTDIDS_DEFAULT                  "nand0=nand.0"
 170 #define MTDPARTS_DEFAULT                "mtdparts=nand.0:" \
 171                                         "128k(NAND.SPL)," \
 172                                         "128k(NAND.SPL.backup1)," \
 173                                         "128k(NAND.SPL.backup2)," \
 174                                         "128k(NAND.SPL.backup3)," \
 175                                         "256k(NAND.u-boot-spl-os)," \
 176                                         "1m(NAND.u-boot)," \
 177                                         "128k(NAND.u-boot-env)," \
 178                                         "128k(NAND.u-boot-env.backup1)," \
 179                                         "8m(NAND.kernel)," \
 180                                         "-(NAND.rootfs)"
 181 #define CONFIG_SYS_NAND_U_BOOT_OFFS     0x000c0000
 182 /* NAND: SPL related configs */
 183 #ifdef CONFIG_SPL_NAND_SUPPORT
 184 #define CONFIG_SPL_NAND_AM33XX_BCH
 185 #endif
 186 /* NAND: SPL falcon mode configs */
 187 #ifdef CONFIG_SPL_OS_BOOT
 188 #define CONFIG_CMD_SPL_NAND_OFS         0x00080000 /* os-boot params*/
 189 #define CONFIG_SYS_NAND_SPL_KERNEL_OFFS 0x00200000 /* kernel offset */
 190 #define CONFIG_CMD_SPL_WRITE_SIZE       0x2000
 191 #endif
 192 #endif /* !CONFIG_NAND */
 193
 194 /* Parallel NOR Support */
 195 #if defined(CONFIG_NOR)
 196 /* NOR: device related configs */
 197 #define CONFIG_SYS_MAX_FLASH_SECT       512
 198 #define CONFIG_SYS_FLASH_CFI_WIDTH      FLASH_CFI_16BIT
 199 #define CONFIG_SYS_FLASH_SIZE           (64 * 1024 * 1024) /* 64 MB */
 200 /* #define CONFIG_INIT_IGNORE_ERROR */
 201 #undef CONFIG_SYS_NO_FLASH
 202 #define CONFIG_CMD_FLASH
 203 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
 204 #define CONFIG_SYS_FLASH_PROTECTION
 205 #define CONFIG_SYS_FLASH_CFI
 206 #define CONFIG_FLASH_CFI_DRIVER
 207 #define CONFIG_FLASH_CFI_MTD
 208 #define CONFIG_SYS_MAX_FLASH_BANKS      1
 209 #define CONFIG_SYS_FLASH_BASE           (0x08000000)
 210 #define CONFIG_SYS_MONITOR_BASE         CONFIG_SYS_FLASH_BASE
 211 /* Reduce SPL size by removing unlikey targets */
 212 #ifdef CONFIG_NOR_BOOT
 213 #define CONFIG_ENV_IS_IN_FLASH
 214 #define CONFIG_ENV_SECT_SIZE            (128 * 1024)    /* 128 KiB */
 215 #define MTDIDS_DEFAULT                  "nor0=physmap-flash.0"
 216 #define MTDPARTS_DEFAULT                "mtdparts=physmap-flash.0:" \
 217                                         "128k(NOR.SPL)," \
 218                                         "128k(NOR.SPL.backup1)," \
 219                                         "128k(NOR.SPL.backup2)," \
 220                                         "128k(NOR.SPL.backup3)," \
 221                                         "256k(NOR.u-boot-spl-os)," \
 222                                         "1m(NOR.u-boot)," \
 223                                         "128k(NOR.u-boot-env)," \
 224                                         "128k(NOR.u-boot-env.backup1)," \
 225                                         "8m(NOR.kernel)," \
 226                                         "-(NOR.rootfs)"
 227 #define CONFIG_ENV_OFFSET               0x001c0000
 228 #define CONFIG_ENV_OFFSET_REDUND        0x001e0000
 229 #endif
 230 #endif  /* NOR support */
 231
 232 #endif /* __CONFIG_DRA7XX_EVM_H */