1 /* SPDX-License-Identifier: GPL-2.0+ */
3 * Copyright 2013-2019 Toradex, Inc.
5 * Configuration settings for the Toradex Colibri iMX6
11 #include <linux/stringify.h>
13 #include "mx6_common.h"
15 #include <asm/arch/imx-regs.h>
16 #include <asm/mach-imx/gpio.h>
18 #define CONFIG_MXC_UART_BASE UART1_BASE
21 #define CFG_SYS_FSL_ESDHC_ADDR 0
22 #define CFG_SYS_FSL_USDHC_NUM 2
26 #define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
27 #define CONFIG_MXC_USB_FLAGS 0
29 #define CONFIG_USBD_HS
31 /* Command definition */
33 #define BOOT_TARGET_DEVICES(func) \
38 #include <config_distro_bootcmd.h>
39 #undef BOOTENV_RUN_NET_USB_START
40 #define BOOTENV_RUN_NET_USB_START ""
42 #define UBOOT_UPDATE \
46 "set_blkcnt=setexpr blkcnt ${filesize} + 0x1ff && " \
47 "setexpr blkcnt ${blkcnt} / 0x200\0" \
48 "update_uboot=run set_blkcnt && mmc dev 0 ${uboot_hwpart} && " \
49 "mmc write ${loadaddr} ${uboot_blk} ${blkcnt}\0" \
50 "update_spl=run set_blkcnt && mmc dev 0 ${uboot_hwpart} && " \
51 "mmc write ${loadaddr} ${uboot_spl_blk} ${blkcnt}\0"
53 #define MEM_LAYOUT_ENV_SETTINGS \
54 "bootm_size=0x10000000\0" \
55 "fdt_addr_r=0x18200000\0" \
56 "kernel_addr_r=" __stringify(CONFIG_SYS_LOAD_ADDR) "\0" \
57 "pxefile_addr_r=0x18300000\0" \
58 "ramdisk_addr_r=0x18400000\0" \
59 "scriptaddr=0x18280000\0"
61 #define CONFIG_EXTRA_ENV_SETTINGS \
63 "boot_file=zImage\0" \
64 "boot_script_dhcp=boot.scr\0" \
66 "defargs=enable_wait_mode=off galcore.contiguousSize=50331648\0" \
67 "fdt_board=eval-v3\0" \
69 MEM_LAYOUT_ENV_SETTINGS \
71 "setethupdate=if env exists ethaddr; then; else setenv ethaddr " \
72 "00:14:2d:00:00:00; fi; tftpboot ${loadaddr} " \
73 "flash_eth.img && source ${loadaddr}\0" \
74 "setsdupdate=setenv interface mmc; setenv drive 1; mmc rescan; load " \
75 "${interface} ${drive}:1 ${loadaddr} flash_blk.img && " \
76 "source ${loadaddr}\0" \
77 "setup=setenv setupargs fec_mac=${ethaddr} " \
78 "consoleblank=0 no_console_suspend=1 console=tty1 " \
79 "console=${console},${baudrate}n8\0 " \
80 "setupdate=run setsdupdate || run setusbupdate || run setethupdate\0" \
81 "setusbupdate=usb start && setenv interface usb; setenv drive 0; " \
82 "load ${interface} ${drive}:1 ${loadaddr} flash_blk.img && " \
83 "source ${loadaddr}\0" \
85 "splashimage=" __stringify(CONFIG_SYS_LOAD_ADDR) "\0" \
88 /* Miscellaneous configurable options */
90 /* Physical Memory Map */
91 #define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
93 #define CFG_SYS_SDRAM_BASE PHYS_SDRAM
94 #define CFG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
95 #define CFG_SYS_INIT_RAM_SIZE IRAM_SIZE
97 #endif /* __CONFIG_H */