1 /* SPDX-License-Identifier: GPL-2.0+ */
3 * Copyright 2013-2019 Toradex, Inc.
5 * Configuration settings for the Toradex Colibri iMX6
11 #include <linux/stringify.h>
13 #include "mx6_common.h"
15 #include <asm/arch/imx-regs.h>
16 #include <asm/mach-imx/gpio.h>
22 #define CONFIG_MXC_UART_BASE UART1_BASE
25 #define CONFIG_SYS_FSL_ESDHC_ADDR 0
26 #define CONFIG_SYS_FSL_USDHC_NUM 2
30 #define CONFIG_USB_MAX_CONTROLLER_COUNT 2
31 #define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
32 #define CONFIG_MXC_USB_FLAGS 0
34 #define CONFIG_USBD_HS
36 /* Framebuffer and LCD */
37 #define CONFIG_IMX_HDMI
38 #define CONFIG_IMX_VIDEO_SKIP
40 /* Command definition */
43 #define CONFIG_IPADDR 192.168.10.2
44 #define CONFIG_NETMASK 255.255.255.0
45 #undef CONFIG_SERVERIP
46 #define CONFIG_SERVERIP 192.168.10.1
48 #define BOOT_TARGET_DEVICES(func) \
53 #include <config_distro_bootcmd.h>
54 #undef BOOTENV_RUN_NET_USB_START
55 #define BOOTENV_RUN_NET_USB_START ""
57 #define UBOOT_UPDATE \
61 "set_blkcnt=setexpr blkcnt ${filesize} + 0x1ff && " \
62 "setexpr blkcnt ${blkcnt} / 0x200\0" \
63 "update_uboot=run set_blkcnt && mmc dev 0 ${uboot_hwpart} && " \
64 "mmc write ${loadaddr} ${uboot_blk} ${blkcnt}\0" \
65 "update_spl=run set_blkcnt && mmc dev 0 ${uboot_hwpart} && " \
66 "mmc write ${loadaddr} ${uboot_spl_blk} ${blkcnt}\0"
68 #define MEM_LAYOUT_ENV_SETTINGS \
69 "bootm_size=0x10000000\0" \
70 "fdt_addr_r=0x12100000\0" \
71 "kernel_addr_r=0x11000000\0" \
72 "pxefile_addr_r=0x17100000\0" \
73 "ramdisk_addr_r=0x12200000\0" \
74 "scriptaddr=0x17000000\0"
76 #define CONFIG_EXTRA_ENV_SETTINGS \
78 "boot_file=zImage\0" \
79 "boot_script_dhcp=boot.scr\0" \
81 "defargs=enable_wait_mode=off galcore.contiguousSize=50331648\0" \
82 "fdt_board=eval-v3\0" \
84 MEM_LAYOUT_ENV_SETTINGS \
86 "setethupdate=if env exists ethaddr; then; else setenv ethaddr " \
87 "00:14:2d:00:00:00; fi; tftpboot ${loadaddr} " \
88 "flash_eth.img && source ${loadaddr}\0" \
89 "setsdupdate=setenv interface mmc; setenv drive 1; mmc rescan; load " \
90 "${interface} ${drive}:1 ${loadaddr} flash_blk.img && " \
91 "source ${loadaddr}\0" \
92 "setup=setenv setupargs fec_mac=${ethaddr} " \
93 "consoleblank=0 no_console_suspend=1 console=tty1 " \
94 "console=${console},${baudrate}n8\0 " \
95 "setupdate=run setsdupdate || run setusbupdate || run setethupdate\0" \
96 "setusbupdate=usb start && setenv interface usb; setenv drive 0; " \
97 "load ${interface} ${drive}:1 ${loadaddr} flash_blk.img && " \
98 "source ${loadaddr}\0" \
100 "splashimage=" __stringify(CONFIG_SYS_LOAD_ADDR) "\0" \
103 /* Miscellaneous configurable options */
105 /* Physical Memory Map */
106 #define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
108 #define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
109 #define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
110 #define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
112 #endif /* __CONFIG_H */