2 * Configuation settings for the Sentec Cobra Board.
4 * (C) Copyright 2003 Josef Baumgartner <josef.baumgartner@telex.de>
6 * See file CREDITS for list of people who contributed to this
9 * This program is free software; you can redistribute it and/or
10 * modify it under the terms of the GNU General Public License as
11 * published by the Free Software Foundation; either version 2 of
12 * the License, or (at your option) any later version.
14 * This program is distributed in the hope that it will be useful,
15 * but WITHOUT ANY WARRANTY; without even the implied warranty of
16 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
17 * GNU General Public License for more details.
19 * You should have received a copy of the GNU General Public License
20 * along with this program; if not, write to the Free Software
21 * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
26 * Version: U-boot 1.0.0 - initial release for Sentec COBRA5272 board
28 * Author: Florian Schlote
30 * For a description of configuration options please refer also to the
31 * general u-boot-1.x.x/README file
36 * board/config.h - configuration options, board specific
40 #ifndef _CONFIG_COBRA5272_H
41 #define _CONFIG_COBRA5272_H
45 * possible values for Sentec board: only Coldfire M5272 processor supported
46 * (please do not change)
50 #define CONFIG_MCF52x2 /* define processor family */
51 #define CONFIG_M5272 /* define processor type */
54 * Defines processor clock - important for correct timings concerning serial
56 * CFG_HZ gives unit: 1000 -> 1 Hz ^= 1000 ms
61 #define CFG_CLK 66000000
62 #define CFG_SDRAM_SIZE 16 /* SDRAM size in MB */
65 * Enable use of Ethernet
72 * Define baudrate for UART1 (console output, tftp, ...)
73 * default value of CONFIG_BAUDRATE for Sentec board: 19200 baud
74 * CFG_BAUDRATE_TABLE defines values that can be selected in u-boot command
79 #define CONFIG_BAUDRATE 19200
80 #define CFG_BAUDRATE_TABLE { 9600 , 19200 , 38400 , 57600, 115200 }
83 * set "#if 0" to "#if 1" if (Hardware)-WATCHDOG should be enabled & change
84 * timeout acc. to your needs
85 * #define CONFIG_WATCHDOG_TIMEOUT x , x is timeout in milliseconds, e. g. 10000
91 #define CONFIG_WATCHDOG
92 #define CONFIG_WATCHDOG_TIMEOUT 10000 /* timeout in milliseconds */
96 * CONFIG_MONITOR_IS_IN_RAM defines if u-boot is started from a different
97 * bootloader residing in flash ('chainloading'); if you want to use
98 * chainloading or want to compile a u-boot binary that can be loaded into
101 * You will need a first stage bootloader then, e. g. colilo or a working BDM
102 * cable (Background Debug Mode)
104 * Setting #if 0: u-boot will start from flash and relocate itself to RAM
106 * Please do not forget to modify the setting of TEXT_BASE
107 * in board/cobra5272/config.mk accordingly (#if 0: 0xffe00000; #if 1: 0x20000)
113 #define CONFIG_MONITOR_IS_IN_RAM /* monitor is started from a preloader */
117 * Configuration for environment
118 * Environment is embedded in u-boot in the second sector of the flash
122 #ifndef CONFIG_MONITOR_IS_IN_RAM
123 #define CFG_ENV_OFFSET 0x4000
124 #define CFG_ENV_SECT_SIZE 0x2000
125 #define CFG_ENV_IS_IN_FLASH 1
126 #define CFG_ENV_IS_EMBEDDED 1
128 #define CFG_ENV_ADDR 0xffe04000
129 #define CFG_ENV_SECT_SIZE 0x2000
130 #define CFG_ENV_IS_IN_FLASH 1
135 * Command line configuration.
137 #include <config_cmd_default.h>
139 #define CONFIG_CMD_PING
141 #undef CONFIG_CMD_LOADS
142 #undef CONFIG_CMD_LOADB
143 #undef CONFIG_CMD_MII
147 *-----------------------------------------------------------------------------
148 * Define user parameters that have to be customized most likely
149 *-----------------------------------------------------------------------------
152 /*AUTOBOOT settings - booting images automatically by u-boot after power on*/
154 #define CONFIG_BOOTDELAY 5 /* used for autoboot, delay in
155 seconds u-boot will wait before starting defined (auto-)boot command, setting
156 to -1 disables delay, setting to 0 will too prevent access to u-boot command
157 interface: u-boot then has to reflashed */
160 /* The following settings will be contained in the environment block ; if you
161 want to use a neutral environment all those settings can be manually set in
162 u-boot: 'set' command */
166 #define CONFIG_BOOTCOMMAND "bootm 0xffe80000" /*Autoboto command, please
167 enter a valid image address in flash */
169 #define CONFIG_BOOTARGS " " /* default bootargs that are
170 considered during boot */
172 /* User network settings */
174 #define CONFIG_ETHADDR 00:00:00:00:00:09 /* default ethernet MAC addr. */
175 #define CONFIG_IPADDR 192.168.100.2 /* default board IP address */
176 #define CONFIG_SERVERIP 192.168.100.1 /* default tftp server IP address */
180 #define CFG_PROMPT "COBRA > " /* Layout of u-boot prompt*/
182 #define CFG_LOAD_ADDR 0x20000 /*Defines default RAM address
183 from which user programs will be started */
187 #define CFG_LONGHELP /* undef to save memory */
189 #if defined(CONFIG_CMD_KGDB)
190 #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
192 #define CFG_CBSIZE 256 /* Console I/O Buffer Size */
194 #define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
195 #define CFG_MAXARGS 16 /* max number of command args */
196 #define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
199 *-----------------------------------------------------------------------------
200 * End of user parameters to be customized
201 *-----------------------------------------------------------------------------
205 * Defines memory range for test
209 #define CFG_MEMTEST_START 0x400
210 #define CFG_MEMTEST_END 0x380000
213 * Low Level Configuration Settings
214 * (address mappings, register initial values, etc.)
215 * You should know what you are doing if you make changes here.
220 * Base register address
224 #define CFG_MBAR 0x10000000 /* Register Base Addrs */
227 * System Conf. Reg. & System Protection Reg.
231 #define CFG_SCR 0x0003;
232 #define CFG_SPR 0xffff;
239 #define CFG_DISCOVER_PHY
240 #define CFG_ENET_BD_BASE 0x780000
242 /*-----------------------------------------------------------------------
243 * Definitions for initial stack pointer and data area (in internal SRAM)
245 #define CFG_INIT_RAM_ADDR 0x20000000
246 #define CFG_INIT_RAM_END 0x1000 /* End of used area in internal SRAM */
247 #define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
248 #define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
249 #define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
251 /*-----------------------------------------------------------------------
252 * Start addresses for the final memory configuration
253 * (Set up by the startup code)
254 * Please note that CFG_SDRAM_BASE _must_ start at 0
256 #define CFG_SDRAM_BASE 0x00000000
259 *-------------------------------------------------------------------------
260 * RAM SIZE (is defined above)
261 *-----------------------------------------------------------------------
264 /* #define CFG_SDRAM_SIZE 16 */
267 *-----------------------------------------------------------------------
270 #define CFG_FLASH_BASE 0xffe00000
272 #ifdef CONFIG_MONITOR_IS_IN_RAM
273 #define CFG_MONITOR_BASE 0x20000
275 #define CFG_MONITOR_BASE (CFG_FLASH_BASE + 0x400)
278 #define CFG_MONITOR_LEN 0x20000
279 #define CFG_MALLOC_LEN (256 << 10)
280 #define CFG_BOOTPARAMS_LEN 64*1024
283 * For booting Linux, the board info and command line data
284 * have to be in the first 8 MB of memory, since this is
285 * the maximum mapped by the Linux kernel during initialization ??
287 #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
289 /*-----------------------------------------------------------------------
292 #define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
293 #define CFG_MAX_FLASH_SECT 11 /* max number of sectors on one chip */
294 #define CFG_FLASH_ERASE_TOUT 1000 /* flash timeout */
296 /*-----------------------------------------------------------------------
297 * Cache Configuration
299 #define CFG_CACHELINE_SIZE 16
301 /*-----------------------------------------------------------------------
302 * Memory bank definitions
304 * Please refer also to Motorola Coldfire user manual - Chapter XXX
305 * <http://e-www.motorola.com/files/dsp/doc/ref_manual/MCF5272UM.pdf>
307 #define CFG_BR0_PRELIM 0xFFE00201
308 #define CFG_OR0_PRELIM 0xFFE00014
310 #define CFG_BR1_PRELIM 0
311 #define CFG_OR1_PRELIM 0
313 #define CFG_BR2_PRELIM 0
314 #define CFG_OR2_PRELIM 0
316 #define CFG_BR3_PRELIM 0
317 #define CFG_OR3_PRELIM 0
319 #define CFG_BR4_PRELIM 0
320 #define CFG_OR4_PRELIM 0
322 #define CFG_BR5_PRELIM 0
323 #define CFG_OR5_PRELIM 0
325 #define CFG_BR6_PRELIM 0
326 #define CFG_OR6_PRELIM 0
328 #define CFG_BR7_PRELIM 0x00000701
329 #define CFG_OR7_PRELIM 0xFF00007C
331 /*-----------------------------------------------------------------------
334 #define LED_STAT_0 0xffff /*all LEDs off*/
335 #define LED_STAT_1 0xfffe
336 #define LED_STAT_2 0xfffd
337 #define LED_STAT_3 0xfffb
338 #define LED_STAT_4 0xfff7
339 #define LED_STAT_5 0xffef
340 #define LED_STAT_6 0xffdf
341 #define LED_STAT_7 0xff00 /*all LEDs on*/
343 /*-----------------------------------------------------------------------
344 * Port configuration (GPIO)
346 #define CFG_PACNT 0x00000000 /* PortA control reg.: All pins are external
348 #define CFG_PADDR 0x00FF /* PortA direction reg.: PA7 to PA0 are outputs
349 (1^=output, 0^=input) */
350 #define CFG_PADAT LED_STAT_0 /* PortA value reg.: Turn all LED off */
351 #define CFG_PBCNT 0x55554155 /* PortB control reg.: Ethernet/UART
353 #define CFG_PBDDR 0x0000 /* PortB direction: All pins configured as inputs */
354 #define CFG_PBDAT 0x0000 /* PortB value reg. */
355 #define CFG_PDCNT 0x00000000 /* PortD control reg. */
357 #endif /* _CONFIG_COBRA5272_H */