include/configs/cm_t54.h

   1 /*
   2  * Config file for Compulab CM-T54 board
   3  *
   4  * Copyright (C) 2014, Compulab Ltd - http://compulab.co.il/
   5  *
   6  * Author: Dmitry Lifshitz <lifshitz@compulab.co.il>
   7  *
   8  * SPDX-License-Identifier:     GPL-2.0+
   9  */
  10
  11 #ifndef __CONFIG_CM_T54_H
  12 #define __CONFIG_CM_T54_H
  13
  14 #define CONFIG_CM_T54
  15 #define CONFIG_DRAM_2G
  16
  17 #include <configs/ti_omap5_common.h>
  18
  19 /* EEPROM related defines */
  20 #define CONFIG_SYS_I2C_OMAP34XX
  21 #define CONFIG_SYS_I2C_EEPROM_ADDR      0x50
  22 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN  1
  23 #define CONFIG_SYS_I2C_EEPROM_BUS       0
  24
  25 /* Enable SD/MMC CD and WP GPIOs */
  26 #define OMAP_HSMMC_USE_GPIO
  27
  28 /* UART setup */
  29 #define CONFIG_CONS_INDEX               4
  30 #define CONFIG_SYS_NS16550_COM4         UART4_BASE
  31
  32 /* MMC ENV related defines */
  33 #undef CONFIG_ENV_OFFSET
  34 #undef CONFIG_ENV_SIZE
  35
  36 #define CONFIG_ENV_IS_IN_MMC
  37 #define CONFIG_SYS_MMC_ENV_DEV          1               /* SLOT2: eMMC(1) */
  38 #define CONFIG_SYS_MMC_ENV_PART         0
  39 #define CONFIG_ENV_OFFSET               0xc0000         /* (in bytes) 768 KB */
  40 #define CONFIG_ENV_SIZE                 (16 << 10)      /* 16 KB */
  41 #define CONFIG_ENV_OFFSET_REDUND        (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
  42 #define CONFIG_SYS_REDUNDAND_ENVIRONMENT
  43
  44 /* Enhance our eMMC support / experience. */
  45 #define CONFIG_HSMMC2_8BIT
  46 #define CONFIG_SUPPORT_EMMC_BOOT
  47
  48 /* SATA Boot related defines */
  49 #define CONFIG_SPL_SATA_BOOT_DEVICE             0
  50 #define CONFIG_SYS_SATA_FAT_BOOT_PARTITION      1
  51
  52 #define CONFIG_SCSI
  53 #define CONFIG_LIBATA
  54 #define CONFIG_SCSI_AHCI
  55 #define CONFIG_SCSI_AHCI_PLAT
  56 #define CONFIG_SYS_SCSI_MAX_SCSI_ID     1
  57 #define CONFIG_SYS_SCSI_MAX_LUN         1
  58 #define CONFIG_SYS_SCSI_MAX_DEVICE      (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
  59                                                 CONFIG_SYS_SCSI_MAX_LUN)
  60 /* USB UHH support options */
  61 #define CONFIG_USB_EHCI_OMAP
  62 #define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS      3
  63 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
  64
  65 #define CONFIG_OMAP_EHCI_PHY2_RESET_GPIO        76 /* HSIC2 HUB #RESET */
  66 #define CONFIG_OMAP_EHCI_PHY3_RESET_GPIO        83 /* HSIC3 ETH #RESET */
  67
  68 /* Enabled commands */
  69
  70 /* EEPROM */
  71 #define CONFIG_CMD_EEPROM
  72 #define CONFIG_ENV_EEPROM_IS_ON_I2C
  73 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN          1
  74 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS       4
  75 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS   5
  76 #define CONFIG_SYS_EEPROM_SIZE                  256
  77
  78 #define CONFIG_CMD_EEPROM_LAYOUT
  79 #define CONFIG_EEPROM_LAYOUT_HELP_STRING "v2, v3"
  80
  81 /* USB Networking options */
  82 #define CONFIG_USB_HOST_ETHER
  83 #define CONFIG_USB_ETHER_SMSC95XX
  84 #define CONFIG_USB_ETHER_RNDIS
  85 #define CONFIG_USB_ETHER_ASIX
  86 #define CONFIG_USB_ETHER_MCS7830
  87
  88 /*
  89  * Miscellaneous configurable options
  90  */
  91 #undef CONFIG_SYS_AUTOLOAD
  92 #undef CONFIG_EXTRA_ENV_SETTINGS
  93 #undef CONFIG_BOOTCOMMAND
  94
  95 #define CONFIG_SYS_AUTOLOAD             "no"
  96
  97 #define CONFIG_EXTRA_ENV_SETTINGS \
  98         DEFAULT_LINUX_BOOT_ENV \
  99         "baudrate=115200\0" \
 100         "bootdelay=3\0" \
 101         "autoload=no\0" \
 102         "bootscr=bootscr.img\0" \
 103         "fdtfile=omap5-sbc-t54.dtb\0" \
 104         "kernel=zImage-cm-t54\0" \
 105         "ramdisk=ramdisk-cm-t54.img\0" \
 106         "console=ttyO3\0" \
 107         "ramdisksize=16384\0" \
 108         "mmcdev=0\0" \
 109         "mmcroot=/dev/mmcblk1p2\0" \
 110         "mmcargs=setenv bootargs console=${console} " \
 111                 "root=${mmcroot} rw rootwait\0" \
 112         "ramroot=/dev/ram0\0" \
 113         "ramargs=setenv bootargs console=${console} " \
 114                 "root=${ramroot} ramdisk_size=${ramdisksize} rw\0" \
 115         "mmcloadkernel=load mmc ${mmcdev} ${loadaddr} ${kernel}\0" \
 116         "mmcloadfdt=load mmc ${mmcdev} ${fdtaddr} ${fdtfile}\0" \
 117         "mmcloadramdisk=load mmc ${mmcdev} ${rdaddr} ${ramdisk}\0" \
 118         "mmcloadbootscript=load mmc ${mmcdev} ${loadaddr} ${bootsrc}\0" \
 119         "mmcbootscript=echo Running bootscript from mmc${mmcdev}...; " \
 120                         "source ${loadaddr}\0" \
 121         "mmcbootlinux=echo Booting from mmc${mmcdev} ...; " \
 122                         "bootz ${loadaddr} ${rdaddr} ${fdtaddr}\0" \
 123         "mmcboot=if mmc dev ${mmcdev} && mmc rescan; then " \
 124                         "if run mmcloadbootscript; " \
 125                                 "then run mmcbootscript; " \
 126                         "fi; " \
 127                         "if run mmcloadkernel; then " \
 128                                 "if run mmcloadfdt; then " \
 129                                         "if run mmcloadramdisk; then " \
 130                                                 "run ramargs; " \
 131                                                 "run mmcbootlinux; " \
 132                                         "fi; " \
 133                                         "run mmcargs; " \
 134                                         "setenv rdaddr - ; " \
 135                                         "run mmcbootlinux; " \
 136                                 "fi; " \
 137                         "fi; " \
 138                 "fi;\0"
 139
 140 #define CONFIG_BOOTCOMMAND \
 141         "bootcmd=run mmcboot || setenv mmcdev 1; setenv mmcroot /dev/mmcblk0p2; run mmcboot;"
 142
 143 #endif /* __CONFIG_CM_T54_H */