include/configs/cgtqmx6eval.h

   1 /*
   2  *
   3  * Congatec Conga-QEVAl board configuration file.
   4  *
   5  * Copyright (C) 2010-2011 Freescale Semiconductor, Inc.
   6  * Based on Freescale i.MX6Q Sabre Lite board configuration file.
   7  * Copyright (C) 2013, Adeneo Embedded <www.adeneo-embedded.com>
   8  * Leo Sartre, <lsartre@adeneo-embedded.com>
   9  *
  10  * SPDX-License-Identifier:     GPL-2.0+
  11  */
  12
  13 #ifndef __CONFIG_CGTQMX6EVAL_H
  14 #define __CONFIG_CGTQMX6EVAL_H
  15
  16 #include "mx6_common.h"
  17
  18 #define CONFIG_MACH_TYPE        4122
  19
  20 #ifdef CONFIG_SPL
  21 #define CONFIG_SYS_SPI_U_BOOT_OFFS      (64 * 1024)
  22 #include "imx6_spl.h"
  23 #endif
  24
  25 /* Size of malloc() pool */
  26 #define CONFIG_SYS_MALLOC_LEN           (10 * 1024 * 1024)
  27
  28 #define CONFIG_MISC_INIT_R
  29
  30 #define CONFIG_MXC_UART
  31 #define CONFIG_MXC_UART_BASE           UART2_BASE
  32
  33 /* MMC Configs */
  34 #define CONFIG_SYS_FSL_ESDHC_ADDR      0
  35
  36 /* SPI NOR */
  37 #define CONFIG_SPI_FLASH
  38 #define CONFIG_SPI_FLASH_STMICRO
  39 #define CONFIG_SPI_FLASH_SST
  40 #define CONFIG_SF_DEFAULT_BUS           0
  41 #define CONFIG_SF_DEFAULT_SPEED         20000000
  42 #define CONFIG_SF_DEFAULT_MODE          (SPI_MODE_0)
  43
  44 /* Thermal support */
  45 #define CONFIG_IMX_THERMAL
  46
  47 /* I2C Configs */
  48 #define CONFIG_SYS_I2C
  49 #define CONFIG_SYS_I2C_MXC
  50 #define CONFIG_SYS_I2C_MXC_I2C1         /* enable I2C bus 1 */
  51 #define CONFIG_SYS_I2C_MXC_I2C2         /* enable I2C bus 2 */
  52 #define CONFIG_SYS_I2C_MXC_I2C2         /* enable I2C bus 2 */
  53 #define CONFIG_SYS_I2C_SPEED              100000
  54
  55 /* PMIC */
  56 #define CONFIG_POWER
  57 #define CONFIG_POWER_I2C
  58 #define CONFIG_POWER_PFUZE100
  59 #define CONFIG_POWER_PFUZE100_I2C_ADDR  0x08
  60
  61 /* USB Configs */
  62 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
  63 #define CONFIG_MXC_USB_PORTSC   (PORT_PTS_UTMI | PORT_PTS_PTW)
  64 #define CONFIG_MXC_USB_FLAGS    0
  65 #define CONFIG_USB_MAX_CONTROLLER_COUNT 2 /* Enabled USB controller number */
  66
  67 #define CONFIG_USBD_HS
  68
  69 /* Framebuffer */
  70 #define CONFIG_VIDEO_IPUV3
  71 #define CONFIG_VIDEO_BMP_RLE8
  72 #define CONFIG_SPLASH_SCREEN
  73 #define CONFIG_SPLASH_SCREEN_ALIGN
  74 #define CONFIG_BMP_16BPP
  75 #define CONFIG_VIDEO_LOGO
  76 #define CONFIG_VIDEO_BMP_LOGO
  77 #define CONFIG_IMX_HDMI
  78
  79 /* SATA */
  80 #define CONFIG_SYS_SATA_MAX_DEVICE      1
  81 #define CONFIG_DWC_AHSATA_PORT_ID       0
  82 #define CONFIG_DWC_AHSATA_BASE_ADDR     SATA_ARB_BASE_ADDR
  83 #define CONFIG_LBA48
  84
  85 /* Ethernet */
  86 #define CONFIG_FEC_MXC
  87 #define CONFIG_MII
  88 #define IMX_FEC_BASE                    ENET_BASE_ADDR
  89 #define CONFIG_FEC_XCV_TYPE             RGMII
  90 #define CONFIG_ETHPRIME                 "FEC"
  91 #define CONFIG_FEC_MXC_PHYADDR          6
  92 #define CONFIG_PHY_ATHEROS
  93
  94 /* Command definition */
  95
  96 #define CONFIG_MXC_UART_BASE    UART2_BASE
  97 #define CONSOLE_DEV     "ttymxc1"
  98 #define CONFIG_MMCROOT          "/dev/mmcblk0p2"
  99 #define CONFIG_SYS_MMC_ENV_DEV          0
 100
 101 #define CONFIG_EXTRA_ENV_SETTINGS \
 102         "script=boot.scr\0" \
 103         "image=zImage\0" \
 104         "fdtfile=undefined\0" \
 105         "fdt_addr_r=0x18000000\0" \
 106         "boot_fdt=try\0" \
 107         "ip_dyn=yes\0" \
 108         "console=" CONSOLE_DEV "\0" \
 109         "dfuspi=dfu 0 sf 0:0:10000000:0\0" \
 110         "dfu_alt_info_spl=spl raw 0x400\0" \
 111         "dfu_alt_info_img=u-boot raw 0x10000\0" \
 112         "dfu_alt_info=spl raw 0x400\0" \
 113         "bootm_size=0x10000000\0" \
 114         "mmcdev=" __stringify(CONFIG_SYS_MMC_ENV_DEV) "\0" \
 115         "mmcpart=1\0" \
 116         "mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \
 117         "update_sd_firmware=" \
 118                 "if test ${ip_dyn} = yes; then " \
 119                         "setenv get_cmd dhcp; " \
 120                 "else " \
 121                         "setenv get_cmd tftp; " \
 122                 "fi; " \
 123                 "if mmc dev ${mmcdev}; then "   \
 124                         "if ${get_cmd} ${update_sd_firmware_filename}; then " \
 125                                 "setexpr fw_sz ${filesize} / 0x200; " \
 126                                 "setexpr fw_sz ${fw_sz} + 1; "  \
 127                                 "mmc write ${loadaddr} 0x2 ${fw_sz}; " \
 128                         "fi; "  \
 129                 "fi\0" \
 130         "mmcargs=setenv bootargs console=${console},${baudrate} " \
 131                 "root=${mmcroot}\0" \
 132         "loadbootscript=" \
 133                 "fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
 134         "bootscript=echo Running bootscript from mmc ...; " \
 135                 "source\0" \
 136         "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
 137         "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr_r} ${fdtfile}\0" \
 138         "mmcboot=echo Booting from mmc ...; " \
 139                 "run mmcargs; " \
 140                 "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
 141                         "if run loadfdt; then " \
 142                                 "bootz ${loadaddr} - ${fdt_addr_r}; " \
 143                         "else " \
 144                                 "if test ${boot_fdt} = try; then " \
 145                                         "bootz; " \
 146                                 "else " \
 147                                         "echo WARN: Cannot load the DT; " \
 148                                 "fi; " \
 149                         "fi; " \
 150                 "else " \
 151                         "bootz; " \
 152                 "fi;\0" \
 153         "findfdt="\
 154                 "if test $board_rev = MX6Q ; then " \
 155                         "setenv fdtfile imx6q-qmx6.dtb; fi; " \
 156                 "if test $board_rev = MX6DL ; then " \
 157                         "setenv fdtfile imx6dl-qmx6.dtb; fi; " \
 158                 "if test $fdtfile = undefined; then " \
 159                         "echo WARNING: Could not determine dtb to use; fi; \0" \
 160         "netargs=setenv bootargs console=${console},${baudrate} " \
 161                 "root=/dev/nfs " \
 162                 "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
 163         "netboot=echo Booting from net ...; " \
 164                 "run netargs; " \
 165                 "if test ${ip_dyn} = yes; then " \
 166                         "setenv get_cmd dhcp; " \
 167                 "else " \
 168                         "setenv get_cmd tftp; " \
 169                 "fi; " \
 170                 "${get_cmd} ${image}; " \
 171                 "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
 172                         "if ${get_cmd} ${fdt_addr_r} ${fdtfile}; then " \
 173                                 "bootz ${loadaddr} - ${fdt_addr_r}; " \
 174                         "else " \
 175                                 "if test ${boot_fdt} = try; then " \
 176                                         "bootz; " \
 177                                 "else " \
 178                                         "echo WARN: Cannot load the DT; " \
 179                                 "fi; " \
 180                         "fi; " \
 181                 "else " \
 182                         "bootz; " \
 183                 "fi;\0" \
 184         "spilock=sf probe && sf protect lock 0x3f0000 0x10000;"\
 185
 186 #define CONFIG_BOOTCOMMAND \
 187         "run spilock;"      \
 188         "run findfdt; " \
 189         "mmc dev ${mmcdev};" \
 190         "if mmc rescan; then " \
 191                 "if run loadbootscript; then " \
 192                 "run bootscript; " \
 193                 "else " \
 194                         "if run loadimage; then " \
 195                                 "run mmcboot; " \
 196                         "else run netboot; " \
 197                         "fi; " \
 198                 "fi; " \
 199         "else run netboot; fi"
 200
 201 #define CONFIG_SYS_MEMTEST_START       0x10000000
 202 #define CONFIG_SYS_MEMTEST_END         0x10010000
 203 #define CONFIG_SYS_MEMTEST_SCRATCH     0x10800000
 204
 205 /* Physical Memory Map */
 206 #define CONFIG_NR_DRAM_BANKS           1
 207 #define PHYS_SDRAM                     MMDC0_ARB_BASE_ADDR
 208
 209 #define CONFIG_SYS_SDRAM_BASE          PHYS_SDRAM
 210 #define CONFIG_SYS_INIT_RAM_ADDR       IRAM_BASE_ADDR
 211 #define CONFIG_SYS_INIT_RAM_SIZE       IRAM_SIZE
 212
 213 #define CONFIG_SYS_INIT_SP_OFFSET \
 214         (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 215 #define CONFIG_SYS_INIT_SP_ADDR \
 216         (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
 217
 218 /* Environment organization */
 219 #if defined (CONFIG_ENV_IS_IN_MMC)
 220 #define CONFIG_ENV_OFFSET               (6 * 64 * 1024)
 221 #define CONFIG_SYS_MMC_ENV_DEV          0
 222 #endif
 223
 224 #define CONFIG_ENV_SIZE                 (8 * 1024)
 225
 226 #if defined(CONFIG_ENV_IS_IN_SPI_FLASH)
 227 #define CONFIG_ENV_OFFSET               (768 * 1024)
 228 #define CONFIG_ENV_SECT_SIZE            (64 * 1024)
 229 #define CONFIG_ENV_SPI_BUS              CONFIG_SF_DEFAULT_BUS
 230 #define CONFIG_ENV_SPI_CS               CONFIG_SF_DEFAULT_CS
 231 #define CONFIG_ENV_SPI_MODE             CONFIG_SF_DEFAULT_MODE
 232 #define CONFIG_ENV_SPI_MAX_HZ           CONFIG_SF_DEFAULT_SPEED
 233 #endif
 234
 235 #endif                         /* __CONFIG_CGTQMX6EVAL_H */