1 /* SPDX-License-Identifier: GPL-2.0+ */
3 * Configuration header file for K3 AM654 EVM
5 * Copyright (C) 2017-2018 Texas Instruments Incorporated - http://www.ti.com/
6 * Lokesh Vutla <lokeshvutla@ti.com>
9 #ifndef __CONFIG_AM654_EVM_H
10 #define __CONFIG_AM654_EVM_H
12 #include <linux/sizes.h>
13 #include <config_distro_bootcmd.h>
14 #include <environment/ti/mmc.h>
15 #include <environment/ti/k3_rproc.h>
17 /* DDR Configuration */
18 #define CONFIG_SYS_SDRAM_BASE1 0x880000000
20 /* SPL Loader Configuration */
21 #ifdef CONFIG_TARGET_AM654_A53_EVM
22 #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SPL_TEXT_BASE + \
23 CONFIG_SYS_K3_NON_SECURE_MSRAM_SIZE)
26 * Maximum size in memory allocated to the SPL BSS. Keep it as tight as
27 * possible (to allow the build to go through), as this directly affects
28 * our memory footprint. The less we use for BSS the more we have available
29 * for everything else.
31 #define CONFIG_SPL_BSS_MAX_SIZE 0x5000
33 * Link BSS to be within SPL in a dedicated region located near the top of
34 * the MCU SRAM, this way making it available also before relocation. Note
35 * that we are not using the actual top of the MCU SRAM as there is a memory
36 * location filled in by the boot ROM that we want to read out without any
37 * interference from the C context.
39 #define CONFIG_SPL_BSS_START_ADDR (CONFIG_SYS_K3_BOOT_PARAM_TABLE_INDEX -\
40 CONFIG_SPL_BSS_MAX_SIZE)
41 /* Set the stack right below the SPL BSS section */
42 #define CONFIG_SYS_INIT_SP_ADDR CONFIG_SPL_BSS_START_ADDR
43 /* Configure R5 SPL post-relocation malloc pool in DDR */
44 #define CONFIG_SYS_SPL_MALLOC_START 0x84000000
45 #define CONFIG_SYS_SPL_MALLOC_SIZE SZ_16M
48 #ifdef CONFIG_SYS_K3_SPL_ATF
49 #define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "tispl.bin"
52 #ifndef CONFIG_CPU_V7R
53 #define CONFIG_SKIP_LOWLEVEL_INIT
56 #define CONFIG_SPL_MAX_SIZE CONFIG_SYS_K3_MAX_DOWNLODABLE_IMAGE_SIZE
58 #define CONFIG_SYS_BOOTM_LEN SZ_64M
60 #define PARTS_DEFAULT \
61 /* Linux partitions */ \
62 "name=rootfs,start=0,size=-,uuid=${uuid_gpt_rootfs}\0"
64 /* U-Boot general configuration */
65 #define EXTRA_ENV_AM65X_BOARD_SETTINGS \
67 "setenv name_fdt k3-am654-base-board.dtb;" \
68 "setenv fdtfile ${name_fdt}\0" \
69 "loadaddr=0x80080000\0" \
70 "fdtaddr=0x82000000\0" \
71 "overlayaddr=0x83000000\0" \
73 "console=ttyS2,115200n8\0" \
74 "args_all=setenv optargs earlycon=ns16550a,mmio32,0x02800000\0" \
75 "run_kern=booti ${loadaddr} ${rd_spec} ${fdtaddr}\0" \
77 /* U-Boot MMC-specific configuration */
78 #define EXTRA_ENV_AM65X_BOARD_SETTINGS_MMC \
84 "init_mmc=run args_all args_mmc\0" \
85 "get_fdt_mmc=load mmc ${bootpart} ${fdtaddr} ${bootdir}/${name_fdt}\0" \
87 "fdt address ${fdtaddr};" \
88 "fdt resize 0x100000;" \
89 "for overlay in $name_overlays;" \
91 "load mmc ${bootpart} ${overlayaddr} ${bootdir}/${overlay};" \
92 "fdt apply ${overlayaddr};" \
94 "get_kern_mmc=load mmc ${bootpart} ${loadaddr} " \
95 "${bootdir}/${name_kern}\0" \
96 "get_fit_mmc=load mmc ${bootpart} ${addr_fit} " \
97 "${bootdir}/${name_fit}\0" \
98 "partitions=" PARTS_DEFAULT
100 #ifdef DEFAULT_RPROCS
101 #undef DEFAULT_RPROCS
103 #define DEFAULT_RPROCS "" \
104 "0 /lib/firmware/am65x-mcu-r5f0_0-fw " \
105 "1 /lib/firmware/am65x-mcu-r5f0_1-fw "
107 /* Incorporate settings into the U-Boot environment */
108 #define CONFIG_EXTRA_ENV_SETTINGS \
109 DEFAULT_MMC_TI_ARGS \
110 DEFAULT_FIT_TI_ARGS \
111 EXTRA_ENV_AM65X_BOARD_SETTINGS \
112 EXTRA_ENV_AM65X_BOARD_SETTINGS_MMC \
113 EXTRA_ENV_RPROC_SETTINGS
115 /* MMC ENV related defines */
116 #ifdef CONFIG_ENV_IS_IN_MMC
117 #define CONFIG_SYS_MMC_ENV_DEV 0
118 #define CONFIG_SYS_MMC_ENV_PART 1
121 #define CONFIG_SUPPORT_EMMC_BOOT
123 /* Now for the remaining common defines */
124 #include <configs/ti_armv7_common.h>
126 #endif /* __CONFIG_AM654_EVM_H */