1 /* SPDX-License-Identifier: GPL-2.0+ */
3 * Configuration header file for K3 AM642 SoC family
5 * Copyright (C) 2020-2021 Texas Instruments Incorporated - https://www.ti.com/
6 * Keerthy <j-keerthy@ti.com>
9 #ifndef __CONFIG_AM642_EVM_H
10 #define __CONFIG_AM642_EVM_H
12 #include <linux/sizes.h>
13 #include <config_distro_bootcmd.h>
14 #include <environment/ti/mmc.h>
16 /* DDR Configuration */
17 #define CONFIG_SYS_SDRAM_BASE1 0x880000000
19 #ifdef CONFIG_SYS_K3_SPL_ATF
20 #define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "tispl.bin"
23 #ifndef CONFIG_CPU_V7R
24 #define CONFIG_SKIP_LOWLEVEL_INIT
27 #define CONFIG_SPL_MAX_SIZE CONFIG_SYS_K3_MAX_DOWNLODABLE_IMAGE_SIZE
28 #if defined(CONFIG_TARGET_AM642_A53_EVM)
29 #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SPL_TEXT_BASE + \
30 CONFIG_SYS_K3_NON_SECURE_MSRAM_SIZE - 4)
33 * Maximum size in memory allocated to the SPL BSS. Keep it as tight as
34 * possible (to allow the build to go through), as this directly affects
35 * our memory footprint. The less we use for BSS the more we have available
36 * for everything else.
38 #define CONFIG_SPL_BSS_MAX_SIZE 0x1000
40 * Link BSS to be within SPL in a dedicated region located near the top of
41 * the MCU SRAM, this way making it available also before relocation. Note
42 * that we are not using the actual top of the MCU SRAM as there is a memory
43 * location filled in by the boot ROM that we want to read out without any
44 * interference from the C context.
46 #define CONFIG_SPL_BSS_START_ADDR (CONFIG_SYS_K3_BOOT_PARAM_TABLE_INDEX -\
47 CONFIG_SPL_BSS_MAX_SIZE)
48 /* Set the stack right below the SPL BSS section */
49 #define CONFIG_SYS_INIT_SP_ADDR CONFIG_SPL_BSS_START_ADDR
50 /* Configure R5 SPL post-relocation malloc pool in DDR */
51 #define CONFIG_SYS_SPL_MALLOC_START 0x84000000
52 #define CONFIG_SYS_SPL_MALLOC_SIZE SZ_16M
55 #define PARTS_DEFAULT \
56 /* Linux partitions */ \
57 "name=rootfs,start=0,size=-,uuid=${uuid_gpt_rootfs}\0"
59 /* U-Boot general configuration */
60 #define EXTRA_ENV_AM642_BOARD_SETTINGS \
62 "if test $board_name = am64x_gpevm; then " \
63 "setenv fdtfile k3-am642-evm.dtb; fi; " \
64 "if test $board_name = am64x_skevm; then " \
65 "setenv fdtfile k3-am642-sk.dtb; fi;" \
66 "if test $fdtfile = undefined; then " \
67 "echo WARNING: Could not determine device tree to use; fi; \0" \
69 "console=ttyS2,115200n8\0" \
70 "args_all=setenv optargs earlycon=ns16550a,mmio32,0x02800000 " \
72 "run_kern=booti ${loadaddr} ${rd_spec} ${fdtaddr}\0"
74 /* U-Boot MMC-specific configuration */
75 #define EXTRA_ENV_AM642_BOARD_SETTINGS_MMC \
81 "init_mmc=run args_all args_mmc\0" \
82 "get_fdt_mmc=load mmc ${bootpart} ${fdtaddr} ${bootdir}/${fdtfile}\0" \
84 "fdt address ${fdtaddr};" \
85 "fdt resize 0x100000;" \
86 "for overlay in $name_overlays;" \
88 "load mmc ${bootpart} ${dtboaddr} ${bootdir}/${overlay} && " \
89 "fdt apply ${dtboaddr};" \
91 "get_kern_mmc=load mmc ${bootpart} ${loadaddr} " \
92 "${bootdir}/${name_kern}\0" \
93 "get_fit_mmc=load mmc ${bootpart} ${addr_fit} " \
94 "${bootdir}/${name_fit}\0" \
95 "partitions=" PARTS_DEFAULT
97 /* Incorporate settings into the U-Boot environment */
98 #define CONFIG_EXTRA_ENV_SETTINGS \
99 DEFAULT_LINUX_BOOT_ENV \
100 DEFAULT_MMC_TI_ARGS \
101 EXTRA_ENV_AM642_BOARD_SETTINGS \
102 EXTRA_ENV_AM642_BOARD_SETTINGS_MMC
104 /* Now for the remaining common defines */
105 #include <configs/ti_armv7_common.h>
107 /* MMC ENV related defines */
108 #ifdef CONFIG_ENV_IS_IN_MMC
109 #define CONFIG_SYS_MMC_ENV_DEV 0
110 #define CONFIG_SYS_MMC_ENV_PART 1
113 #endif /* __CONFIG_AM642_EVM_H */