include/configs/am335x_shc.h

   1 /* SPDX-License-Identifier: GPL-2.0+ */
   2 /*
   3  * (C) Copyright 2016
   4  * Heiko Schocher, DENX Software Engineering, hs@denx.de.
   5  *
   6  * Based on:
   7  * am335x_evm.h
   8  *
   9  * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/
  10  */
  11
  12 #ifndef __CONFIG_AM335X_SHC_H
  13 #define __CONFIG_AM335X_SHC_H
  14
  15 #include <configs/ti_am335x_common.h>
  16
  17 /* settings we don;t want on this board */
  18 #undef CONFIG_CMD_SPI
  19
  20 #define CONFIG_CMD_CACHE
  21
  22 #ifndef CONFIG_SPL_BUILD
  23 # define CONFIG_TIMESTAMP
  24 #endif
  25
  26 #define CONFIG_SYS_BOOTM_LEN            (16 << 20)
  27
  28 /* Clock Defines */
  29 #define V_OSCK                          24000000  /* Clock output from T2 */
  30 #define V_SCLK                          (V_OSCK)
  31
  32 /*
  33  * in case of SD Card or Network boot we want to have a possibility to
  34  * debrick the shc, therefore do not read environment from eMMC
  35  */
  36 #if defined(CONFIG_SHC_SDBOOT) || defined(CONFIG_SHC_NETBOOT)
  37 #define CONFIG_SYS_MMC_ENV_DEV          0
  38 #else
  39 #define CONFIG_SYS_MMC_ENV_DEV          1
  40 #endif
  41
  42 /*
  43  * Info when using boot partitions: As environment resides within first
  44  * 128 kB, MLO must start at 128 kB == 0x20000
  45  * ENV at MMC Boot0 Partition - 0/Undefined=user, 1=boot0, 2=boot1,
  46  * 4..7=general0..3
  47  */
  48
  49 #define CONFIG_HSMMC2_8BIT
  50
  51 #ifndef CONFIG_SHC_ICT
  52 /*
  53  * In builds other than ICT, reset to retry after timeout
  54  * Define a timeout after which a stopped bootloader continues autoboot
  55  * (only works with CONFIG_RESET_TO_RETRY)
  56  */
  57 # define CONFIG_BOOT_RETRY_TIME 30
  58 # define CONFIG_RESET_TO_RETRY
  59 #endif
  60
  61 #ifndef CONFIG_SPL_BUILD
  62 #define CONFIG_EXTRA_ENV_SETTINGS \
  63         "loadaddr=0x80200000\0" \
  64         "kloadaddr=0x84000000\0" \
  65         "fdtaddr=0x85000000\0" \
  66         "fdt_high=0xffffffff\0" \
  67         "rdaddr=0x81000000\0" \
  68         "bootfile=uImage\0" \
  69         "fdtfile=am335x-shc.dtb\0" \
  70         "verify=no\0" \
  71         "serverip=10.55.152.184\0" \
  72         "rootpath=/srv/nfs/shc-rootfs\0" \
  73         "console=ttyO0,115200n8\0" \
  74         "optargs=quiet\0" \
  75         "mmcdev=1\0" \
  76         "harakiri=0\0" \
  77         "mmcpart=2\0" \
  78         "active_root=root1\0" \
  79         "inactive_root=root2\0" \
  80         "mmcrootfstype=ext4 rootwait\0" \
  81         "nfsopts=nolock\0" \
  82         "static_ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}" \
  83                 "::off\0" \
  84         "ip_method=none\0" \
  85         "bootargs_defaults=setenv bootargs " \
  86                 "console=${console} " \
  87                 "${optargs}\0" \
  88         "mmcargs=run bootargs_defaults;" \
  89                 "setenv bootargs ${bootargs} " \
  90                 "root=${mmcroot} " \
  91                 "rootfstype=${mmcrootfstype} ip=${ip_method}\0" \
  92         "netargs=setenv bootargs console=${console} " \
  93                 "${optargs} " \
  94                 "root=/dev/nfs " \
  95                 "nfsroot=${serverip}:${rootpath},${nfsopts} rw " \
  96                 "ip=dhcp\0" \
  97         "bootenv=uEnv.txt\0" \
  98         "loadbootenv=if fatload mmc ${mmcdev} ${loadaddr} ${bootenv}; then " \
  99                         "echo Loaded environment from ${bootenv}; " \
 100                         "run importbootenv; " \
 101                 "fi;\0" \
 102         "importbootenv=echo Importing environment variables from uEnv.txt ...; " \
 103                 "env import -t $loadaddr $filesize\0" \
 104         "loaduimagefat=fatload mmc ${mmcdev} ${kloadaddr} ${bootfile}\0" \
 105         "loaduimage=ext2load mmc ${mmcdev}:${mmcpart} ${kloadaddr} /boot/${bootfile}\0" \
 106         "loadfdt=ext2load mmc ${mmcdev}:${mmcpart} ${fdtaddr} /boot/${fdtfile}\0" \
 107         "netloaduimage=tftp ${loadaddr} ${bootfile}\0" \
 108         "netloadfdt=tftp ${fdtaddr} ${fdtfile}\0" \
 109         "mmcboot=echo Booting Linux from ${mmcdevice} ...; " \
 110                 "run mmcargs; " \
 111                 "if run loadfdt; then " \
 112                         "echo device tree detected; " \
 113                         "bootm ${kloadaddr} - ${fdtaddr}; " \
 114                 "else " \
 115                         "bootm ${kloadaddr}; " \
 116                 "fi; \0" \
 117         "netboot=echo Booting from network ...; " \
 118                 "setenv autoload no; " \
 119                 "dhcp; " \
 120                 "run netloaduimage; " \
 121                 "run netargs; " \
 122                 "echo NFS path: ${serverip}:${rootpath};" \
 123                 "if run netloadfdt; then " \
 124                         "echo device tree detected; " \
 125                         "bootm ${loadaddr} - ${fdtaddr}; " \
 126                 "else " \
 127                         "bootm ${loadaddr}; " \
 128                 "fi; \0" \
 129         "emmc_erase=if test ${harakiri} = 1 ; then echo erase emmc ...; setenv mmcdev 1; mmc erase 0 200; reset; fi; \0" \
 130         "mmcpart_gp=mmcpart gp 1 40; \0" \
 131         "mmcpart_enhance=mmcpart enhance 0 64; \0" \
 132         "mmcpart_rel_write=mmcpart rel_write 1f; \0" \
 133         "mmcpart_commit=mmcpart commit 1; \0" \
 134         "mmc_hw_part=run mmcpart_gp; run mmcpart_enhance; run mmcpart_rel_write; run mmcpart_commit; \0" \
 135         "led_success=gpio set 22; \0" \
 136         "fusecmd=mmc dev 1; if mmcpart iscommitted; then echo HW Partitioning already committed; mmcpart list; else run mmc_hw_part; fi; run led_success; \0" \
 137         "uenv_exec=if test -n $uenvcmd; then " \
 138                         "echo Running uenvcmd ...; " \
 139                         "run uenvcmd; " \
 140                 "fi;\0" \
 141         "sd_setup=echo SD/MMC-Card detected on device 0; " \
 142                 "setenv mmcdevice SD; " \
 143                 "setenv mmcdev 0; " \
 144                 "setenv mmcpart 2; " \
 145                 "setenv mmcroot /dev/mmcblk${mmcdev}p${mmcpart};\0" \
 146         "emmc_setup=echo eMMC detected on device 1; " \
 147                 "setenv mmcdevice eMMC; " \
 148                 "setenv mmcdev 1; " \
 149                 "run emmc_erase; " \
 150                 "if test ${active_root} = root2; then " \
 151                         "echo Active root is partition 6 (root2); " \
 152                         "setenv mmcpart 6; " \
 153                 "else " \
 154                         "echo Active root is partition 5 (root1); " \
 155                         "setenv mmcpart 5; " \
 156                 "fi; " \
 157                 "setenv mmcroot /dev/mmcblk${mmcdev}p${mmcpart};\0"
 158 #endif /* #ifndef CONFIG_SPL_BUILD */
 159
 160 #if defined CONFIG_SHC_NETBOOT
 161 /* Network Boot */
 162 # define CONFIG_BOOTCOMMAND \
 163         "run fusecmd; " \
 164         "if run netboot; then " \
 165                 "echo Booting from network; " \
 166         "else " \
 167                 "echo ERROR: Cannot boot from network!; " \
 168                 "panic; " \
 169         "fi; "
 170
 171 #elif defined CONFIG_SHC_SDBOOT /* !defined CONFIG_SHC_NETBOOT */
 172 /* SD-Card Boot */
 173 # define CONFIG_BOOTCOMMAND \
 174         "if mmc dev 0; mmc rescan; then " \
 175                 "run sd_setup; " \
 176         "else " \
 177                 "echo ERROR: SD/MMC-Card not detected!; " \
 178                 "panic; " \
 179         "fi; " \
 180         "if run loaduimage; then " \
 181                 "echo Bootable SD/MMC-Card inserted, booting from it!; " \
 182                 "run mmcboot; " \
 183         "else " \
 184                 "echo ERROR: Unable to load uImage from SD/MMC-Card!; " \
 185                 "panic; " \
 186         "fi; "
 187
 188 #elif defined CONFIG_SHC_ICT
 189 /* ICT adapter boots only u-boot and does HW partitioning */
 190 # define CONFIG_BOOTCOMMAND \
 191         "if mmc dev 0; mmc rescan; then " \
 192                 "run sd_setup; " \
 193         "else " \
 194                 "echo ERROR: SD/MMC-Card not detected!; " \
 195                 "panic; " \
 196         "fi; " \
 197         "run fusecmd; "
 198
 199 #else /* !defined CONFIG_SHC_NETBOOT, !defined CONFIG_SHC_SDBOOT */
 200 /* Regular Boot from internal eMMC */
 201 # define CONFIG_BOOTCOMMAND \
 202         "if mmc dev 1; mmc rescan; then " \
 203                 "run emmc_setup; " \
 204         "else " \
 205                 "echo ERROR: eMMC device not detected!; " \
 206                 "panic; " \
 207         "fi; " \
 208         "if run loaduimage; then " \
 209                 "run mmcboot; " \
 210         "else " \
 211                 "echo ERROR Unable to load uImage from eMMC!; " \
 212                 "echo Performing Rollback!; " \
 213                 "setenv _active_ ${active_root}; " \
 214                 "setenv _inactive_ ${inactive_root}; " \
 215                 "setenv active_root ${_inactive_}; " \
 216                 "setenv inactive_root ${_active_}; " \
 217                 "saveenv; " \
 218                 "reset; " \
 219         "fi; "
 220
 221 #endif /* Regular Boot */
 222
 223 /* NS16550 Configuration */
 224 #define CONFIG_SYS_NS16550_COM1         0x44e09000      /* UART0 */
 225 #define CONFIG_SYS_NS16550_COM2         0x48022000      /* UART1 */
 226 #define CONFIG_SYS_NS16550_COM3         0x48024000      /* UART2 */
 227 #define CONFIG_SYS_NS16550_COM4         0x481a6000      /* UART3 */
 228 #define CONFIG_SYS_NS16550_COM5         0x481a8000      /* UART4 */
 229 #define CONFIG_SYS_NS16550_COM6         0x481aa000      /* UART5 */
 230
 231 /* PMIC support */
 232 #define CONFIG_POWER_TPS65217
 233
 234 /* SPL */
 235
 236 /*
 237  * Disable MMC DM for SPL build and can be re-enabled after adding
 238  * DM support in SPL
 239  */
 240 #ifdef CONFIG_SPL_BUILD
 241 #undef CONFIG_DM_MMC
 242 #undef CONFIG_TIMER
 243 #endif
 244
 245 #define CONFIG_BOOTP_DEFAULT
 246 #define CONFIG_BOOTP_DNS2
 247 #define CONFIG_BOOTP_SEND_HOSTNAME
 248 #define CONFIG_NET_RETRY_COUNT         10
 249
 250 /* I2C configuration */
 251 #define CONFIG_SYS_I2C_EEPROM_ADDR      0x50    /* Main EEPROM */
 252 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN  2
 253 #define CONFIG_SYS_I2C_SPEED            400000
 254 #define CONFIG_SYS_I2C_SLAVE            1
 255 #endif  /* ! __CONFIG_AM335X_SHC_H */