include/configs/actux1.h

   1 /*
   2  * (C) Copyright 2007
   3  * Michael Schwingen, michael@schwingen.org
   4  *
   5  * Configuration settings for the AcTux-1 board.
   6  *
   7  * See file CREDITS for list of people who contributed to this
   8  * project.
   9  *
  10  * This program is free software; you can redistribute it and/or
  11  * modify it under the terms of the GNU General Public License as
  12  * published by the Free Software Foundation; either version 2 of
  13  * the License, or (at your option) any later version.
  14  *
  15  * This program is distributed in the hope that it will be useful,
  16  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  17  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
  18  * GNU General Public License for more details.
  19  *
  20  * You should have received a copy of the GNU General Public License
  21  * along with this program; if not, write to the Free Software
  22  * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
  23  * MA 02111-1307 USA
  24  */
  25
  26 #ifndef __CONFIG_H
  27 #define __CONFIG_H
  28
  29 #define CONFIG_IXP425                   1
  30 #define CONFIG_ACTUX1                   1
  31
  32 #define CONFIG_DISPLAY_CPUINFO          1
  33 #define CONFIG_DISPLAY_BOARDINFO        1
  34
  35 #define CONFIG_IXP_SERIAL
  36 #define CONFIG_SYS_IXP425_CONSOLE               IXP425_UART2
  37 #define CONFIG_BAUDRATE                 115200
  38 #define CONFIG_BOOTDELAY                3
  39 #define CONFIG_ZERO_BOOTDELAY_CHECK     /* check for keypress on bootdelay==0 */
  40 #define CONFIG_BOARD_EARLY_INIT_F       1
  41 #define CONFIG_SYS_LDSCRIPT     "board/actux1/u-boot.lds"
  42
  43 /***************************************************************
  44  * U-boot generic defines start here.
  45  ***************************************************************/
  46 /*
  47  * Size of malloc() pool
  48  */
  49 #define CONFIG_SYS_MALLOC_LEN                   (CONFIG_ENV_SIZE + 128*1024)
  50
  51 /* allow to overwrite serial and ethaddr */
  52 #define CONFIG_ENV_OVERWRITE
  53
  54 /* Command line configuration. */
  55 #include <config_cmd_default.h>
  56
  57 #define CONFIG_CMD_ELF
  58 #ifdef CONFIG_PCI
  59 #define CONFIG_CMD_PCI
  60 #define CONFIG_PCI_PNP
  61 #define CONFIG_IXP_PCI
  62 #define CONFIG_PCI_SCAN_SHOW
  63 #define CONFIG_CMD_PCI_ENUM
  64 #endif
  65
  66 #define CONFIG_BOOTCOMMAND              "run boot_flash"
  67 /* enable passing of ATAGs */
  68 #define CONFIG_CMDLINE_TAG              1
  69 #define CONFIG_SETUP_MEMORY_TAGS        1
  70 #define CONFIG_INITRD_TAG               1
  71 #define CONFIG_REVISION_TAG             1
  72
  73 #if defined(CONFIG_CMD_KGDB)
  74 # define CONFIG_KGDB_BAUDRATE           230400
  75 /* which serial port to use */
  76 # define CONFIG_KGDB_SER_INDEX          1
  77 #endif
  78
  79 /* Miscellaneous configurable options */
  80 #define CONFIG_SYS_LONGHELP
  81 #define CONFIG_SYS_PROMPT                       "=> "
  82 /* Console I/O Buffer Size */
  83 #define CONFIG_SYS_CBSIZE                       256
  84 /* Print Buffer Size */
  85 #define CONFIG_SYS_PBSIZE                       (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
  86 /* max number of command args */
  87 #define CONFIG_SYS_MAXARGS                      16
  88 /* Boot Argument Buffer Size */
  89 #define CONFIG_SYS_BARGSIZE                     CONFIG_SYS_CBSIZE
  90
  91 #define CONFIG_SYS_MEMTEST_START                0x00400000
  92 #define CONFIG_SYS_MEMTEST_END                  0x00800000
  93
  94 /* timer clock - 2* OSC_IN system clock */
  95 #define CONFIG_IXP425_TIMER_CLK                 66666666
  96 #define CONFIG_SYS_HZ                           1000
  97
  98 /* default load address */
  99 #define CONFIG_SYS_LOAD_ADDR                    0x00010000
 100
 101 /* valid baudrates */
 102 #define CONFIG_SYS_BAUDRATE_TABLE               { 9600, 19200, 38400, 57600,    \
 103                                           115200, 230400 }
 104 #define CONFIG_SERIAL_RTS_ACTIVE        1
 105
 106 /*
 107  * Stack sizes
 108  * The stack sizes are set up in start.S using the settings below
 109  */
 110 #define CONFIG_STACKSIZE                (128*1024)      /* regular stack */
 111
 112 /* Expansion bus settings */
 113 #define CONFIG_SYS_EXP_CS0                      0xbd113842
 114
 115 /* SDRAM settings */
 116 #define CONFIG_NR_DRAM_BANKS            1
 117 #define PHYS_SDRAM_1                    0x00000000
 118 #define CONFIG_SYS_SDRAM_BASE                   0x00000000
 119
 120 #ifdef CONFIG_RAM_32MB
 121 # define CONFIG_SYS_SDR_CONFIG                  0x18
 122 # define PHYS_SDRAM_1_SIZE              0x02000000
 123 # define CONFIG_SYS_SDRAM_REFRESH_CNT           0x81a
 124 # define CONFIG_SYS_SDR_MODE_CONFIG             0x1
 125 # define CONFIG_SYS_DRAM_SIZE                   0x02000000
 126 #else /* 16MB SDRAM */
 127 # define CONFIG_SYS_SDR_CONFIG                  0x3A
 128 # define PHYS_SDRAM_1_SIZE              0x01000000
 129 # define CONFIG_SYS_SDRAM_REFRESH_CNT           0x81a
 130 # define CONFIG_SYS_SDR_MODE_CONFIG             0x1
 131 # define CONFIG_SYS_DRAM_SIZE                   0x01000000
 132 #endif
 133
 134 /* FLASH organization */
 135 #define CONFIG_SYS_TEXT_BASE            0x50000000
 136 #ifdef CONFIG_FLASH2X2
 137 # define CONFIG_SYS_MAX_FLASH_BANKS             2
 138 /* max number of sectors on one chip */
 139 # define CONFIG_SYS_MAX_FLASH_SECT              40
 140 # define PHYS_FLASH_1                   0x50000000
 141 # define PHYS_FLASH_2                   0x50200000
 142 # define CONFIG_SYS_FLASH_BANKS_LIST            { PHYS_FLASH_1, PHYS_FLASH_2 }
 143 #endif
 144 #ifdef CONFIG_FLASH1X8
 145 # define CONFIG_SYS_MAX_FLASH_BANKS             1
 146 /* max number of sectors on one chip */
 147 # define CONFIG_SYS_MAX_FLASH_SECT              140
 148 # define PHYS_FLASH_1                   0x50000000
 149 # define CONFIG_SYS_FLASH_BANKS_LIST            { PHYS_FLASH_1 }
 150 #endif
 151
 152 #define CONFIG_SYS_FLASH_BASE                   PHYS_FLASH_1
 153 #define CONFIG_SYS_MONITOR_BASE         PHYS_FLASH_1
 154 #define CONFIG_SYS_MONITOR_LEN                  (256 << 10)
 155 #define CONFIG_BOARD_SIZE_LIMIT                 262144
 156
 157 /* Use common CFI driver */
 158 #define CONFIG_SYS_FLASH_CFI
 159 #define CONFIG_FLASH_CFI_DRIVER
 160 /* no byte writes on IXP4xx */
 161 #define CONFIG_SYS_FLASH_CFI_WIDTH              FLASH_CFI_16BIT
 162 /* print 'E' for empty sector on flinfo */
 163 #define CONFIG_SYS_FLASH_EMPTY_INFO
 164
 165 /* Ethernet */
 166
 167 /* include IXP4xx NPE support */
 168 #define CONFIG_IXP4XX_NPE               1
 169 /* NPE0 PHY address */
 170 #define CONFIG_PHY_ADDR                 0
 171 /* NPE1 PHY address (HW Release E only) */
 172 #define CONFIG_PHY1_ADDR                1
 173 /* MII PHY management */
 174 #define CONFIG_MII                      1
 175 /* Number of ethernet rx buffers & descriptors */
 176 #define CONFIG_SYS_RX_ETH_BUFFER                16
 177 #define CONFIG_RESET_PHY_R              1
 178
 179 #define CONFIG_HAS_ETH1                 1
 180
 181 #define CONFIG_CMD_DHCP
 182 #define CONFIG_CMD_NET
 183 #define CONFIG_CMD_MII
 184 #define CONFIG_CMD_PING
 185 #undef  CONFIG_CMD_NFS
 186
 187 /* BOOTP options */
 188 #define CONFIG_BOOTP_BOOTFILESIZE
 189 #define CONFIG_BOOTP_BOOTPATH
 190 #define CONFIG_BOOTP_GATEWAY
 191 #define CONFIG_BOOTP_HOSTNAME
 192
 193 /* Cache Configuration */
 194 #define CONFIG_SYS_CACHELINE_SIZE               32
 195
 196 /*
 197  * environment organization:
 198  * one flash sector, embedded in uboot area (bottom bootblock flash)
 199  */
 200 #define CONFIG_ENV_IS_IN_FLASH          1
 201 #define CONFIG_ENV_SIZE                 0x2000
 202 #define CONFIG_ENV_ADDR                 (PHYS_FLASH_1 + 0x4000)
 203 #define CONFIG_SYS_USE_PPCENV                   1
 204
 205 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
 206         "npe_ucode=50040000\0"                                          \
 207         "mtd=IXP4XX-Flash.0:256k(uboot),64k(ucode),1152k(linux),-(root)\0" \
 208         "kerneladdr=50050000\0"                                         \
 209         "kernelfile=actux1/uImage\0"                                    \
 210         "rootfile=actux1/rootfs\0"                                      \
 211         "rootaddr=50170000\0"                                           \
 212         "loadaddr=10000\0"                                              \
 213         "updateboot_ser=mw.b 10000 ff 40000;"                           \
 214         " loady ${loadaddr};"                                           \
 215         " run eraseboot writeboot\0"                                    \
 216         "updateboot_net=mw.b 10000 ff 40000;"                           \
 217         " tftp ${loadaddr} actux1/u-boot.bin;"                          \
 218         " run eraseboot writeboot\0"                                    \
 219         "eraseboot=protect off 50000000 50003fff;"                      \
 220         " protect off 50006000 5003ffff;"                               \
 221         " erase 50000000 50003fff;"                                     \
 222         " erase 50006000 5003ffff\0"                                    \
 223         "writeboot=cp.b 10000 50000000 4000;"                           \
 224         " cp.b 16000 50006000 3a000\0"                                  \
 225         "updateucode=loady;"                                            \
 226         " era ${npe_ucode} +${filesize};"                               \
 227         " cp.b ${loadaddr} ${npe_ucode} ${filesize}\0"                  \
 228         "updateroot=tftp ${loadaddr} ${rootfile};"                      \
 229         " era ${rootaddr} +${filesize};"                                \
 230         " cp.b ${loadaddr} ${rootaddr} ${filesize}\0"                   \
 231         "updatekern=tftp ${loadaddr} ${kernelfile};"                    \
 232         " era ${kerneladdr} +${filesize};"                              \
 233         " cp.b ${loadaddr} ${kerneladdr} ${filesize}\0"                 \
 234         "flashargs=setenv bootargs mtdparts=${mtd} root=/dev/mtdblock3" \
 235         " rootfstype=squashfs,jffs2 init=/etc/preinit\0"                \
 236         "netargs=setenv bootargs mtdparts=${mtd} root=/dev/mtdblock3"   \
 237         " rootfstype=squashfs,jffs2 init=/etc/preinit\0"                \
 238         "addtty=setenv bootargs ${bootargs} console=ttyS1,${baudrate}\0" \
 239         "addeth=setenv bootargs ${bootargs} ethaddr=${ethaddr}\0"       \
 240         "boot_flash=run flashargs addtty addeth;"                       \
 241         " bootm ${kerneladdr}\0"                                        \
 242         "boot_net=run netargs addtty addeth;"                           \
 243         " tftpboot ${loadaddr} ${kernelfile};"                          \
 244         " bootm\0"
 245
 246 /* additions for new relocation code, must be added to all boards */
 247 #define CONFIG_SYS_INIT_SP_ADDR                                         \
 248         (CONFIG_SYS_SDRAM_BASE + 0x1000 - GENERATED_GBL_DATA_SIZE)
 249
 250 #endif /* __CONFIG_H */