include/configs/UCP1020.h

   1 /*
   2  * Copyright 2013-2015 Arcturus Networks, Inc.
   3  *           http://www.arcturusnetworks.com/products/ucp1020/
   4  * based on include/configs/p1_p2_rdb_pc.h
   5  * original copyright follows:
   6  * Copyright 2009-2011 Freescale Semiconductor, Inc.
   7  *
   8  * SPDX-License-Identifier:     GPL-2.0+
   9  */
  10
  11 /*
  12  * QorIQ uCP1020-xx boards configuration file
  13  */
  14 #ifndef __CONFIG_H
  15 #define __CONFIG_H
  16
  17 #define CONFIG_PCIE1    /* PCIE controller 1 (slot 1) */
  18 #define CONFIG_PCIE2    /* PCIE controller 2 (slot 2) */
  19 #define CONFIG_FSL_PCI_INIT     /* Use common FSL init code */
  20 #define CONFIG_PCI_INDIRECT_BRIDGE      /* indirect PCI bridge support */
  21 #define CONFIG_FSL_PCIE_RESET   /* need PCIe reset errata */
  22 #define CONFIG_SYS_PCI_64BIT    /* enable 64-bit PCI resources */
  23
  24 #if defined(CONFIG_TARTGET_UCP1020T1)
  25
  26 #define CONFIG_UCP1020_REV_1_3
  27
  28 #define CONFIG_BOARDNAME "uCP1020-64EE512-0U1-XR-T1"
  29
  30 #define CONFIG_TSEC_ENET
  31 #define CONFIG_TSEC1
  32 #define CONFIG_TSEC3
  33 #define CONFIG_HAS_ETH0
  34 #define CONFIG_HAS_ETH1
  35 #define CONFIG_ETHADDR          00:19:D3:FF:FF:FF
  36 #define CONFIG_ETH1ADDR         00:19:D3:FF:FF:FE
  37 #define CONFIG_ETH2ADDR         00:19:D3:FF:FF:FD
  38 #define CONFIG_IPADDR           10.80.41.229
  39 #define CONFIG_SERVERIP         10.80.41.227
  40 #define CONFIG_NETMASK          255.255.252.0
  41 #define CONFIG_ETHPRIME         "eTSEC3"
  42
  43 #ifndef CONFIG_SPI_FLASH
  44 #endif
  45 #define CONFIG_SYS_REDUNDAND_ENVIRONMENT
  46
  47 #define CONFIG_SYS_L2_SIZE      (256 << 10)
  48
  49 #define CONFIG_LAST_STAGE_INIT
  50
  51 #endif
  52
  53 #if defined(CONFIG_TARGET_UCP1020)
  54
  55 #define CONFIG_UCP1020
  56 #define CONFIG_UCP1020_REV_1_3
  57
  58 #define CONFIG_BOARDNAME_LOCAL "uCP1020-64EEE512-OU1-XR"
  59
  60 #define CONFIG_TSEC_ENET
  61 #define CONFIG_TSEC1
  62 #define CONFIG_TSEC2
  63 #define CONFIG_TSEC3
  64 #define CONFIG_HAS_ETH0
  65 #define CONFIG_HAS_ETH1
  66 #define CONFIG_HAS_ETH2
  67 #define CONFIG_ETHADDR          00:06:3B:FF:FF:FF
  68 #define CONFIG_ETH1ADDR         00:06:3B:FF:FF:FE
  69 #define CONFIG_ETH2ADDR         00:06:3B:FF:FF:FD
  70 #define CONFIG_IPADDR           192.168.1.81
  71 #define CONFIG_IPADDR1          192.168.1.82
  72 #define CONFIG_IPADDR2          192.168.1.83
  73 #define CONFIG_SERVERIP         192.168.1.80
  74 #define CONFIG_GATEWAYIP        102.168.1.1
  75 #define CONFIG_NETMASK          255.255.255.0
  76 #define CONFIG_ETHPRIME         "eTSEC1"
  77
  78 #ifndef CONFIG_SPI_FLASH
  79 #endif
  80 #define CONFIG_SYS_REDUNDAND_ENVIRONMENT
  81
  82 #define CONFIG_SYS_L2_SIZE      (256 << 10)
  83
  84 #define CONFIG_LAST_STAGE_INIT
  85
  86 #endif
  87
  88 #ifdef CONFIG_SDCARD
  89 #define CONFIG_RAMBOOT_SDCARD
  90 #define CONFIG_SYS_RAMBOOT
  91 #define CONFIG_SYS_EXTRA_ENV_RELOC
  92 #define CONFIG_RESET_VECTOR_ADDRESS     0x1107fffc
  93 #endif
  94
  95 #ifdef CONFIG_SPIFLASH
  96 #define CONFIG_RAMBOOT_SPIFLASH
  97 #define CONFIG_SYS_RAMBOOT
  98 #define CONFIG_SYS_EXTRA_ENV_RELOC
  99 #define CONFIG_RESET_VECTOR_ADDRESS     0x1107fffc
 100 #endif
 101
 102 #define CONFIG_SYS_TEXT_BASE_NOR        0xeff80000
 103
 104 #ifndef CONFIG_RESET_VECTOR_ADDRESS
 105 #define CONFIG_RESET_VECTOR_ADDRESS     0xeffffffc
 106 #endif
 107
 108 #ifndef CONFIG_SYS_MONITOR_BASE
 109 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE    /* start of monitor */
 110 #endif
 111
 112 #define CONFIG_MP
 113
 114 #define CONFIG_ENV_OVERWRITE
 115
 116 #define CONFIG_SYS_SATA_MAX_DEVICE      2
 117 #define CONFIG_LBA48
 118
 119 #define CONFIG_SYS_CLK_FREQ     66666666
 120 #define CONFIG_DDR_CLK_FREQ     66666666
 121
 122 #define CONFIG_HWCONFIG
 123
 124 /*
 125  * These can be toggled for performance analysis, otherwise use default.
 126  */
 127 #define CONFIG_L2_CACHE
 128 #define CONFIG_BTB
 129
 130 #define CONFIG_ENABLE_36BIT_PHYS
 131
 132 #define CONFIG_SYS_MEMTEST_START        0x00200000      /* memtest works on */
 133 #define CONFIG_SYS_MEMTEST_END          0x1fffffff
 134
 135 #define CONFIG_SYS_CCSRBAR              0xffe00000
 136 #define CONFIG_SYS_CCSRBAR_PHYS_LOW     CONFIG_SYS_CCSRBAR
 137
 138 /* IN case of NAND bootloader relocate CCSRBAR in RAMboot code not in the 4k
 139        SPL code*/
 140 #ifdef CONFIG_SPL_BUILD
 141 #define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
 142 #endif
 143
 144 /* DDR Setup */
 145 #define CONFIG_DDR_ECC_ENABLE
 146 #ifndef CONFIG_DDR_ECC_ENABLE
 147 #define CONFIG_SYS_DDR_RAW_TIMING
 148 #define CONFIG_DDR_SPD
 149 #endif
 150 #define CONFIG_SYS_SPD_BUS_NUM 1
 151 #undef CONFIG_FSL_DDR_INTERACTIVE
 152
 153 #define CONFIG_SYS_SDRAM_SIZE_LAW       LAW_SIZE_512M
 154 #define CONFIG_CHIP_SELECTS_PER_CTRL    1
 155 #define CONFIG_SYS_SDRAM_SIZE           (1u << (CONFIG_SYS_SDRAM_SIZE_LAW - 19))
 156 #define CONFIG_SYS_DDR_SDRAM_BASE       0x00000000
 157 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE
 158
 159 #define CONFIG_DIMM_SLOTS_PER_CTLR      1
 160
 161 /* Default settings for DDR3 */
 162 #define CONFIG_SYS_DDR_CS0_BNDS         0x0000003f
 163 #define CONFIG_SYS_DDR_CS0_CONFIG       0x80014302
 164 #define CONFIG_SYS_DDR_CS0_CONFIG_2     0x00000000
 165 #define CONFIG_SYS_DDR_CS1_BNDS         0x0040007f
 166 #define CONFIG_SYS_DDR_CS1_CONFIG       0x80014302
 167 #define CONFIG_SYS_DDR_CS1_CONFIG_2     0x00000000
 168
 169 #define CONFIG_SYS_DDR_DATA_INIT        0xdeadbeef
 170 #define CONFIG_SYS_DDR_INIT_ADDR        0x00000000
 171 #define CONFIG_SYS_DDR_INIT_EXT_ADDR    0x00000000
 172 #define CONFIG_SYS_DDR_MODE_CONTROL     0x00000000
 173
 174 #define CONFIG_SYS_DDR_ZQ_CONTROL       0x89080600
 175 #define CONFIG_SYS_DDR_WRLVL_CONTROL    0x8655A608
 176 #define CONFIG_SYS_DDR_SR_CNTR          0x00000000
 177 #define CONFIG_SYS_DDR_RCW_1            0x00000000
 178 #define CONFIG_SYS_DDR_RCW_2            0x00000000
 179 #ifdef CONFIG_DDR_ECC_ENABLE
 180 #define CONFIG_SYS_DDR_CONTROL          0xE70C0000      /* Type = DDR3 & ECC */
 181 #else
 182 #define CONFIG_SYS_DDR_CONTROL          0xC70C0000      /* Type = DDR3 */
 183 #endif
 184 #define CONFIG_SYS_DDR_CONTROL_2        0x04401050
 185 #define CONFIG_SYS_DDR_TIMING_4         0x00220001
 186 #define CONFIG_SYS_DDR_TIMING_5         0x03402400
 187
 188 #define CONFIG_SYS_DDR_TIMING_3         0x00020000
 189 #define CONFIG_SYS_DDR_TIMING_0         0x00330004
 190 #define CONFIG_SYS_DDR_TIMING_1         0x6f6B4846
 191 #define CONFIG_SYS_DDR_TIMING_2         0x0FA8C8CF
 192 #define CONFIG_SYS_DDR_CLK_CTRL         0x03000000
 193 #define CONFIG_SYS_DDR_MODE_1           0x40461520
 194 #define CONFIG_SYS_DDR_MODE_2           0x8000c000
 195 #define CONFIG_SYS_DDR_INTERVAL         0x0C300000
 196
 197 #undef CONFIG_CLOCKS_IN_MHZ
 198
 199 /*
 200  * Memory map
 201  *
 202  * 0x0000_0000 0x7fff_ffff      DDR             Up to 2GB cacheable
 203  * 0x8000_0000 0xdfff_ffff      PCI Express Mem 1G non-cacheable(PCIe * 2)
 204  * 0xec00_0000 0xefff_ffff      NOR flash       Up to 64M non-cacheable CS0/1
 205  * 0xf8f8_0000 0xf8ff_ffff      L2 SRAM         Up to 256K cacheable
 206  *   (early boot only)
 207  * 0xffc0_0000 0xffc3_ffff      PCI IO range    256k non-cacheable
 208  * 0xffd0_0000 0xffd0_3fff      L1 for stack    16K cacheable
 209  * 0xffe0_0000 0xffef_ffff      CCSR            1M non-cacheable
 210  */
 211
 212 /*
 213  * Local Bus Definitions
 214  */
 215 #define CONFIG_SYS_MAX_FLASH_SECT       512     /* 64M */
 216 #define CONFIG_SYS_FLASH_BASE           0xec000000
 217
 218 #define CONFIG_SYS_FLASH_BASE_PHYS      CONFIG_SYS_FLASH_BASE
 219
 220 #define CONFIG_FLASH_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \
 221         | BR_PS_16 | BR_V)
 222
 223 #define CONFIG_FLASH_OR_PRELIM          0xfc000ff7
 224
 225 #define CONFIG_SYS_FLASH_BANKS_LIST     {CONFIG_SYS_FLASH_BASE_PHYS}
 226 #define CONFIG_SYS_FLASH_QUIET_TEST
 227 #define CONFIG_FLASH_SHOW_PROGRESS      45      /* count down from 45/5: 9..1 */
 228
 229 #define CONFIG_SYS_MAX_FLASH_BANKS      1       /* number of banks */
 230
 231 #undef CONFIG_SYS_FLASH_CHECKSUM
 232 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000   /* Flash Erase Timeout (ms) */
 233 #define CONFIG_SYS_FLASH_WRITE_TOUT     500     /* Flash Write Timeout (ms) */
 234
 235 #define CONFIG_FLASH_CFI_DRIVER
 236 #define CONFIG_SYS_FLASH_CFI
 237 #define CONFIG_SYS_FLASH_EMPTY_INFO
 238 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
 239
 240 #define CONFIG_BOARD_EARLY_INIT_R       /* call board_early_init_r function */
 241
 242 #define CONFIG_SYS_INIT_RAM_LOCK
 243 #define CONFIG_SYS_INIT_RAM_ADDR        0xffd00000 /* stack in RAM */
 244 /* Initial L1 address */
 245 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS   CONFIG_SYS_INIT_RAM_ADDR
 246 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0
 247 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS
 248 /* Size of used area in RAM */
 249 #define CONFIG_SYS_INIT_RAM_SIZE        0x00004000
 250
 251 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - \
 252                                         GENERATED_GBL_DATA_SIZE)
 253 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 254
 255 #define CONFIG_SYS_MONITOR_LEN  (256 * 1024)/* Reserve 256 kB for Mon */
 256 #define CONFIG_SYS_MALLOC_LEN   (1024 * 1024)/* Reserved for malloc */
 257
 258 #define CONFIG_SYS_PMC_BASE     0xff980000
 259 #define CONFIG_SYS_PMC_BASE_PHYS        CONFIG_SYS_PMC_BASE
 260 #define CONFIG_PMC_BR_PRELIM    (BR_PHYS_ADDR(CONFIG_SYS_PMC_BASE_PHYS) | \
 261                                         BR_PS_8 | BR_V)
 262 #define CONFIG_PMC_OR_PRELIM    (OR_AM_64KB | OR_GPCM_CSNT | OR_GPCM_XACS | \
 263                                  OR_GPCM_SCY | OR_GPCM_TRLX | OR_GPCM_EHTR | \
 264                                  OR_GPCM_EAD)
 265
 266 #define CONFIG_SYS_BR0_PRELIM   CONFIG_FLASH_BR_PRELIM  /* NOR Base Address */
 267 #define CONFIG_SYS_OR0_PRELIM   CONFIG_FLASH_OR_PRELIM  /* NOR Options */
 268 #ifdef CONFIG_NAND_FSL_ELBC
 269 #define CONFIG_SYS_BR1_PRELIM   CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Addr */
 270 #define CONFIG_SYS_OR1_PRELIM   CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */
 271 #endif
 272
 273 /* Serial Port - controlled on board with jumper J8
 274  * open - index 2
 275  * shorted - index 1
 276  */
 277 #undef CONFIG_SERIAL_SOFTWARE_FIFO
 278 #define CONFIG_SYS_NS16550_SERIAL
 279 #define CONFIG_SYS_NS16550_REG_SIZE     1
 280 #define CONFIG_SYS_NS16550_CLK          get_bus_freq(0)
 281 #if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_INIT_MINIMAL)
 282 #define CONFIG_NS16550_MIN_FUNCTIONS
 283 #endif
 284
 285 #define CONFIG_SYS_BAUDRATE_TABLE       \
 286         {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
 287
 288 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR + 0x4500)
 289 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR + 0x4600)
 290
 291 /* I2C */
 292 #define CONFIG_SYS_I2C
 293 #define CONFIG_SYS_I2C_FSL
 294 #define CONFIG_SYS_FSL_I2C_SPEED        400000
 295 #define CONFIG_SYS_FSL_I2C_SLAVE        0x7F
 296 #define CONFIG_SYS_FSL_I2C_OFFSET       0x3000
 297 #define CONFIG_SYS_FSL_I2C2_SPEED       400000
 298 #define CONFIG_SYS_FSL_I2C2_SLAVE       0x7F
 299 #define CONFIG_SYS_FSL_I2C2_OFFSET      0x3100
 300 #define CONFIG_SYS_I2C_NOPROBES         { {0, 0x29} }
 301 #define CONFIG_SYS_SPD_BUS_NUM          1 /* For rom_loc and flash bank */
 302
 303 #define CONFIG_RTC_DS1337
 304 #define CONFIG_RTC_DS1337_NOOSC
 305 #define CONFIG_SYS_I2C_RTC_ADDR         0x68
 306 #define CONFIG_SYS_I2C_PCA9557_ADDR     0x18
 307 #define CONFIG_SYS_I2C_NCT72_ADDR       0x4C
 308 #define CONFIG_SYS_I2C_IDT6V49205B      0x69
 309
 310 /*
 311  * eSPI - Enhanced SPI
 312  */
 313 #define CONFIG_HARD_SPI
 314
 315 #define CONFIG_SF_DEFAULT_SPEED         10000000
 316 #define CONFIG_SF_DEFAULT_MODE          SPI_MODE_0
 317
 318 #if defined(CONFIG_PCI)
 319 /*
 320  * General PCI
 321  * Memory space is mapped 1-1, but I/O space must start from 0.
 322  */
 323
 324 /* controller 2, direct to uli, tgtid 2, Base address 9000 */
 325 #define CONFIG_SYS_PCIE2_NAME           "PCIe SLOT CON9"
 326 #define CONFIG_SYS_PCIE2_MEM_VIRT       0xa0000000
 327 #define CONFIG_SYS_PCIE2_MEM_BUS        0xa0000000
 328 #define CONFIG_SYS_PCIE2_MEM_PHYS       0xa0000000
 329 #define CONFIG_SYS_PCIE2_MEM_SIZE       0x20000000      /* 512M */
 330 #define CONFIG_SYS_PCIE2_IO_VIRT        0xffc10000
 331 #define CONFIG_SYS_PCIE2_IO_BUS         0x00000000
 332 #define CONFIG_SYS_PCIE2_IO_PHYS        0xffc10000
 333 #define CONFIG_SYS_PCIE2_IO_SIZE        0x00010000      /* 64k */
 334
 335 /* controller 1, Slot 2, tgtid 1, Base address a000 */
 336 #define CONFIG_SYS_PCIE1_NAME           "PCIe SLOT CON10"
 337 #define CONFIG_SYS_PCIE1_MEM_VIRT       0x80000000
 338 #define CONFIG_SYS_PCIE1_MEM_BUS        0x80000000
 339 #define CONFIG_SYS_PCIE1_MEM_PHYS       0x80000000
 340 #define CONFIG_SYS_PCIE1_MEM_SIZE       0x20000000      /* 512M */
 341 #define CONFIG_SYS_PCIE1_IO_VIRT        0xffc00000
 342 #define CONFIG_SYS_PCIE1_IO_BUS         0x00000000
 343 #define CONFIG_SYS_PCIE1_IO_PHYS        0xffc00000
 344 #define CONFIG_SYS_PCIE1_IO_SIZE        0x00010000      /* 64k */
 345
 346 #define CONFIG_PCI_SCAN_SHOW    /* show pci devices on startup */
 347 #endif /* CONFIG_PCI */
 348
 349 /*
 350  * Environment
 351  */
 352 #ifdef CONFIG_ENV_FIT_UCBOOT
 353
 354 #define CONFIG_ENV_ADDR         (CONFIG_SYS_FLASH_BASE + 0x20000)
 355 #define CONFIG_ENV_SIZE         0x20000
 356 #define CONFIG_ENV_SECT_SIZE    0x20000 /* 128K (one sector) */
 357
 358 #else
 359
 360 #define CONFIG_ENV_SPI_BUS      0
 361 #define CONFIG_ENV_SPI_CS       0
 362 #define CONFIG_ENV_SPI_MAX_HZ   10000000
 363 #define CONFIG_ENV_SPI_MODE     0
 364
 365 #ifdef CONFIG_RAMBOOT_SPIFLASH
 366
 367 #define CONFIG_ENV_SIZE         0x3000          /* 12KB */
 368 #define CONFIG_ENV_OFFSET       0x2000          /* 8KB */
 369 #define CONFIG_ENV_SECT_SIZE    0x1000
 370
 371 #if defined(CONFIG_SYS_REDUNDAND_ENVIRONMENT)
 372 /* Address and size of Redundant Environment Sector     */
 373 #define CONFIG_ENV_OFFSET_REDUND        (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
 374 #define CONFIG_ENV_SIZE_REDUND          CONFIG_ENV_SIZE
 375 #endif
 376
 377 #elif defined(CONFIG_RAMBOOT_SDCARD)
 378 #define CONFIG_FSL_FIXED_MMC_LOCATION
 379 #define CONFIG_ENV_SIZE         0x2000
 380 #define CONFIG_SYS_MMC_ENV_DEV  0
 381
 382 #elif defined(CONFIG_SYS_RAMBOOT)
 383 #define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE - 0x1000)
 384 #define CONFIG_ENV_SIZE         0x2000
 385
 386 #else
 387 #define CONFIG_ENV_BASE         (CONFIG_SYS_FLASH_BASE)
 388 #define CONFIG_ENV_SECT_SIZE    0x20000 /* 128K (one sector) */
 389 #define CONFIG_ENV_SIZE         CONFIG_ENV_SECT_SIZE
 390 #define CONFIG_ENV_ADDR         (CONFIG_ENV_BASE + 0xC0000)
 391 #if defined(CONFIG_SYS_REDUNDAND_ENVIRONMENT)
 392 /* Address and size of Redundant Environment Sector     */
 393 #define CONFIG_ENV_ADDR_REDUND  (CONFIG_ENV_ADDR + CONFIG_ENV_SIZE)
 394 #define CONFIG_ENV_SIZE_REDUND  CONFIG_ENV_SIZE
 395 #endif
 396
 397 #endif
 398
 399 #endif  /* CONFIG_ENV_FIT_UCBOOT */
 400
 401 #define CONFIG_LOADS_ECHO               /* echo on for serial download */
 402 #define CONFIG_SYS_LOADS_BAUD_CHANGE    /* allow baudrate change */
 403
 404 /*
 405  * USB
 406  */
 407 #define CONFIG_HAS_FSL_DR_USB
 408
 409 #if defined(CONFIG_HAS_FSL_DR_USB)
 410 #define CONFIG_USB_MAX_CONTROLLER_COUNT 1
 411
 412 #ifdef CONFIG_USB_EHCI_HCD
 413 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 414 #define CONFIG_USB_EHCI_FSL
 415 #endif
 416 #endif
 417
 418 #undef CONFIG_WATCHDOG                  /* watchdog disabled */
 419
 420 #ifdef CONFIG_MMC
 421 #define CONFIG_FSL_ESDHC
 422 #define CONFIG_SYS_FSL_ESDHC_ADDR       CONFIG_SYS_MPC85xx_ESDHC_ADDR
 423 #define CONFIG_MMC_SPI
 424 #endif
 425
 426 /* Misc Extra Settings */
 427 #undef CONFIG_WATCHDOG  /* watchdog disabled */
 428
 429 /*
 430  * Miscellaneous configurable options
 431  */
 432 #define CONFIG_SYS_LOAD_ADDR    0x2000000       /* default load address */
 433 #define CONFIG_SYS_HZ           1000    /* decrementer freq: 1ms tick */
 434
 435 /*
 436  * For booting Linux, the board info and command line data
 437  * have to be in the first 64 MB of memory, since this is
 438  * the maximum mapped by the Linux kernel during initialization.
 439  */
 440 #define CONFIG_SYS_BOOTMAPSZ    (64 << 20)      /* Initial Memory for Linux*/
 441 #define CONFIG_SYS_BOOTM_LEN    (64 << 20)      /* Increase max gunzip size */
 442
 443 #if defined(CONFIG_CMD_KGDB)
 444 #define CONFIG_KGDB_BAUDRATE    230400  /* speed to run kgdb serial port */
 445 #define CONFIG_KGDB_SER_INDEX   2       /* which serial port to use */
 446 #endif
 447
 448 /*
 449  * Environment Configuration
 450  */
 451
 452 #if defined(CONFIG_TSEC_ENET)
 453
 454 #if defined(CONFIG_UCP1020_REV_1_2) || defined(CONFIG_UCP1020_REV_1_3)
 455 #else
 456 #error "UCP1020 module revision is not defined !!!"
 457 #endif
 458
 459 #define CONFIG_BOOTP_SERVERIP
 460
 461 #define CONFIG_MII              /* MII PHY management */
 462 #define CONFIG_TSEC1_NAME       "eTSEC1"
 463 #define CONFIG_TSEC2_NAME       "eTSEC2"
 464 #define CONFIG_TSEC3_NAME       "eTSEC3"
 465
 466 #define TSEC1_PHY_ADDR  4
 467 #define TSEC2_PHY_ADDR  0
 468 #define TSEC2_PHY_ADDR_SGMII    0x00
 469 #define TSEC3_PHY_ADDR  6
 470
 471 #define TSEC1_FLAGS     (TSEC_GIGABIT | TSEC_REDUCED)
 472 #define TSEC2_FLAGS     (TSEC_GIGABIT | TSEC_REDUCED)
 473 #define TSEC3_FLAGS     (TSEC_GIGABIT | TSEC_REDUCED)
 474
 475 #define TSEC1_PHYIDX    0
 476 #define TSEC2_PHYIDX    0
 477 #define TSEC3_PHYIDX    0
 478
 479 #endif
 480
 481 #define CONFIG_HOSTNAME         UCP1020
 482 #define CONFIG_ROOTPATH         "/opt/nfsroot"
 483 #define CONFIG_BOOTFILE         "uImage"
 484 #define CONFIG_UBOOTPATH        u-boot.bin /* U-Boot image on TFTP server */
 485
 486 /* default location for tftp and bootm */
 487 #define CONFIG_LOADADDR         1000000
 488
 489 #if defined(CONFIG_DONGLE)
 490
 491 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
 492 "bootcmd=run prog_spi_mbrbootcramfs\0"                                  \
 493 "bootfile=uImage\0"                                                     \
 494 "consoledev=ttyS0\0"                                                    \
 495 "cramfsfile=image.cramfs\0"                                             \
 496 "dtbaddr=0x00c00000\0"                                                  \
 497 "dtbfile=image.dtb\0"                                                   \
 498 "ethaddr=" __stringify(CONFIG_ETHADDR) "\0"                             \
 499 "eth1addr=" __stringify(CONFIG_ETH1ADDR) "\0"                           \
 500 "eth2addr=" __stringify(CONFIG_ETH2ADDR) "\0"                           \
 501 "fileaddr=0x01000000\0"                                                 \
 502 "filesize=0x00080000\0"                                                 \
 503 "flashmbr=sf probe 0; "                                                 \
 504         "tftp $loadaddr $mbr; "                                         \
 505         "sf erase $mbr_offset +$filesize; "                             \
 506         "sf write $loadaddr $mbr_offset $filesize\0"                    \
 507 "flashrecovery=tftp $recoveryaddr $cramfsfile; "                        \
 508         "protect off $nor_recoveryaddr +$filesize; "                    \
 509         "erase $nor_recoveryaddr +$filesize; "                          \
 510         "cp.b $recoveryaddr $nor_recoveryaddr $filesize; "              \
 511         "protect on $nor_recoveryaddr +$filesize\0 "                    \
 512 "flashuboot=tftp $ubootaddr $ubootfile; "                               \
 513         "protect off $nor_ubootaddr +$filesize; "                       \
 514         "erase $nor_ubootaddr +$filesize; "                             \
 515         "cp.b $ubootaddr $nor_ubootaddr $filesize; "                    \
 516         "protect on $nor_ubootaddr +$filesize\0 "                       \
 517 "flashworking=tftp $workingaddr $cramfsfile; "                          \
 518         "protect off $nor_workingaddr +$filesize; "                     \
 519         "erase $nor_workingaddr +$filesize; "                           \
 520         "cp.b $workingaddr $nor_workingaddr $filesize; "                \
 521         "protect on $nor_workingaddr +$filesize\0 "                     \
 522 "hwconfig=usb1:dr_mode=host,phy_type=ulpi\0 "                           \
 523 "kerneladdr=0x01100000\0"                                               \
 524 "kernelfile=uImage\0"                                                   \
 525 "loadaddr=0x01000000\0"                                                 \
 526 "mbr=uCP1020d.mbr\0"                                                    \
 527 "mbr_offset=0x00000000\0"                                               \
 528 "mmbr=uCP1020Quiet.mbr\0"                                               \
 529 "mmcpart=0:2\0"                                                         \
 530 "mmc__mbrd=fatload mmc $mmcpart $loadaddr $mbr; "                       \
 531         "mmc erase 1 1; "                                               \
 532         "mmc write $loadaddr 1 1\0"                                     \
 533 "mmc__uboot=fatload mmc $mmcpart $loadaddr $ubootfile; "                \
 534         "mmc erase 0x40 0x400; "                                        \
 535         "mmc write $loadaddr 0x40 0x400\0"                              \
 536 "netdev=eth0\0"                                                         \
 537 "nor_recoveryaddr=0xEC0A0000\0"                                         \
 538 "nor_ubootaddr=0xEFF80000\0"                                            \
 539 "nor_workingaddr=0xECFA0000\0"                                          \
 540 "norbootrecovery=setenv bootargs $recoverybootargs"                     \
 541         " console=$consoledev,$baudrate $othbootargs; "                 \
 542         "run norloadrecovery; "                                         \
 543         "bootm $kerneladdr - $dtbaddr\0"                                \
 544 "norbootworking=setenv bootargs $workingbootargs"                       \
 545         " console=$consoledev,$baudrate $othbootargs; "                 \
 546         "run norloadworking; "                                          \
 547         "bootm $kerneladdr - $dtbaddr\0"                                \
 548 "norloadrecovery=mw.l $kerneladdr 0x0 0x00a00000; "                     \
 549         "setenv cramfsaddr $nor_recoveryaddr; "                         \
 550         "cramfsload $dtbaddr $dtbfile; "                                \
 551         "cramfsload $kerneladdr $kernelfile\0"                          \
 552 "norloadworking=mw.l $kerneladdr 0x0 0x00a00000; "                      \
 553         "setenv cramfsaddr $nor_workingaddr; "                          \
 554         "cramfsload $dtbaddr $dtbfile; "                                \
 555         "cramfsload $kerneladdr $kernelfile\0"                          \
 556 "prog_spi_mbr=run spi__mbr\0"                                           \
 557 "prog_spi_mbrboot=run spi__mbr; run spi__boot1; run spi__boot2\0"       \
 558 "prog_spi_mbrbootcramfs=run spi__mbr; run spi__boot1; run spi__boot2; " \
 559         "run spi__cramfs\0"                                             \
 560 "ramboot=setenv bootargs root=/dev/ram ramdisk_size=$ramdisk_size ro"   \
 561         " console=$consoledev,$baudrate $othbootargs; "                 \
 562         "tftp $rootfsaddr $rootfsfile; "                                \
 563         "tftp $loadaddr $kernelfile; "                                  \
 564         "tftp $dtbaddr $dtbfile; "                                      \
 565         "bootm $loadaddr $rootfsaddr $dtbaddr\0"                        \
 566 "ramdisk_size=120000\0"                                                 \
 567 "ramdiskfile=rootfs.ext2.gz.uboot\0"                                    \
 568 "recoveryaddr=0x02F00000\0"                                             \
 569 "recoverybootargs=root=/dev/mtdblock0 rootfstype=cramfs ro\0"           \
 570 "releasefpga=mw.l 0xffe0f000 0x00400000; mw.l 0xffe0f004 0x00000000; "  \
 571         "mw.l 0xffe0f008 0x00400000\0"                                  \
 572 "rootfsaddr=0x02F00000\0"                                               \
 573 "rootfsfile=rootfs.ext2.gz.uboot\0"                                     \
 574 "rootpath=/opt/nfsroot\0"                                               \
 575 "spi__boot1=fatload mmc $mmcpart $loadaddr u-boot.bin; "                \
 576         "protect off 0xeC000000 +$filesize; "                           \
 577         "erase 0xEC000000 +$filesize; "                                 \
 578         "cp.b $loadaddr 0xEC000000 $filesize; "                         \
 579         "cmp.b $loadaddr 0xEC000000 $filesize; "                        \
 580         "protect on 0xeC000000 +$filesize\0"                            \
 581 "spi__boot2=fatload mmc $mmcpart $loadaddr u-boot.bin; "                \
 582         "protect off 0xeFF80000 +$filesize; "                           \
 583         "erase 0xEFF80000 +$filesize; "                                 \
 584         "cp.b $loadaddr 0xEFF80000 $filesize; "                         \
 585         "cmp.b $loadaddr 0xEFF80000 $filesize; "                        \
 586         "protect on 0xeFF80000 +$filesize\0"                            \
 587 "spi__bootd=fatload mmc $mmcpart $loadaddr $ubootd; "                   \
 588         "sf probe 0; sf erase 0x8000 +$filesize; "                      \
 589         "sf write $loadaddr 0x8000 $filesize\0"                         \
 590 "spi__cramfs=fatload mmc $mmcpart $loadaddr image.cramfs; "             \
 591         "protect off 0xec0a0000 +$filesize; "                           \
 592         "erase 0xeC0A0000 +$filesize; "                                 \
 593         "cp.b $loadaddr 0xeC0A0000 $filesize; "                         \
 594         "protect on 0xec0a0000 +$filesize\0"                            \
 595 "spi__mbr=fatload mmc $mmcpart $loadaddr $mmbr; "                       \
 596         "sf probe 1; sf erase 0 +$filesize; "                           \
 597         "sf write $loadaddr 0 $filesize\0"                              \
 598 "spi__mbrd=fatload mmc $mmcpart $loadaddr $mbr; "                       \
 599         "sf probe 0; sf erase 0 +$filesize; "                           \
 600         "sf write $loadaddr 0 $filesize\0"                              \
 601 "tftpflash=tftpboot $loadaddr $uboot; "                                 \
 602         "protect off " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
 603         "erase " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; "  \
 604         "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize; " \
 605         "protect on " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
 606         "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize\0"\
 607 "uboot= " __stringify(CONFIG_UBOOTPATH) "\0"                            \
 608 "ubootaddr=0x01000000\0"                                                \
 609 "ubootfile=u-boot.bin\0"                                                \
 610 "ubootd=u-boot4dongle.bin\0"                                            \
 611 "upgrade=run flashworking\0"                                            \
 612 "usb_phy_type=ulpi\0 "                                                  \
 613 "workingaddr=0x02F00000\0"                                              \
 614 "workingbootargs=root=/dev/mtdblock1 rootfstype=cramfs ro\0"
 615
 616 #else
 617
 618 #if defined(CONFIG_UCP1020T1)
 619
 620 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
 621 "bootcmd=run releasefpga; run norbootworking || run norbootrecovery\0"  \
 622 "bootfile=uImage\0"                                                     \
 623 "consoledev=ttyS0\0"                                                    \
 624 "cramfsfile=image.cramfs\0"                                             \
 625 "dtbaddr=0x00c00000\0"                                                  \
 626 "dtbfile=image.dtb\0"                                                   \
 627 "ethaddr=" __stringify(CONFIG_ETHADDR) "\0"                             \
 628 "eth1addr=" __stringify(CONFIG_ETH1ADDR) "\0"                           \
 629 "eth2addr=" __stringify(CONFIG_ETH2ADDR) "\0"                           \
 630 "fileaddr=0x01000000\0"                                                 \
 631 "filesize=0x00080000\0"                                                 \
 632 "flashmbr=sf probe 0; "                                                 \
 633         "tftp $loadaddr $mbr; "                                         \
 634         "sf erase $mbr_offset +$filesize; "                             \
 635         "sf write $loadaddr $mbr_offset $filesize\0"                    \
 636 "flashrecovery=tftp $recoveryaddr $cramfsfile; "                        \
 637         "protect off $nor_recoveryaddr +$filesize; "                    \
 638         "erase $nor_recoveryaddr +$filesize; "                          \
 639         "cp.b $recoveryaddr $nor_recoveryaddr $filesize; "              \
 640         "protect on $nor_recoveryaddr +$filesize\0 "                    \
 641 "flashuboot=tftp $ubootaddr $ubootfile; "                               \
 642         "protect off $nor_ubootaddr +$filesize; "                       \
 643         "erase $nor_ubootaddr +$filesize; "                             \
 644         "cp.b $ubootaddr $nor_ubootaddr $filesize; "                    \
 645         "protect on $nor_ubootaddr +$filesize\0 "                       \
 646 "flashworking=tftp $workingaddr $cramfsfile; "                          \
 647         "protect off $nor_workingaddr +$filesize; "                     \
 648         "erase $nor_workingaddr +$filesize; "                           \
 649         "cp.b $workingaddr $nor_workingaddr $filesize; "                \
 650         "protect on $nor_workingaddr +$filesize\0 "                     \
 651 "hwconfig=usb1:dr_mode=host,phy_type=ulpi\0 "                           \
 652 "kerneladdr=0x01100000\0"                                               \
 653 "kernelfile=uImage\0"                                                   \
 654 "loadaddr=0x01000000\0"                                                 \
 655 "mbr=uCP1020.mbr\0"                                                     \
 656 "mbr_offset=0x00000000\0"                                               \
 657 "netdev=eth0\0"                                                         \
 658 "nor_recoveryaddr=0xEC0A0000\0"                                         \
 659 "nor_ubootaddr=0xEFF80000\0"                                            \
 660 "nor_workingaddr=0xECFA0000\0"                                          \
 661 "norbootrecovery=setenv bootargs $recoverybootargs"                     \
 662         " console=$consoledev,$baudrate $othbootargs; "                 \
 663         "run norloadrecovery; "                                         \
 664         "bootm $kerneladdr - $dtbaddr\0"                                \
 665 "norbootworking=setenv bootargs $workingbootargs"                       \
 666         " console=$consoledev,$baudrate $othbootargs; "                 \
 667         "run norloadworking; "                                          \
 668         "bootm $kerneladdr - $dtbaddr\0"                                \
 669 "norloadrecovery=mw.l $kerneladdr 0x0 0x00a00000; "                     \
 670         "setenv cramfsaddr $nor_recoveryaddr; "                         \
 671         "cramfsload $dtbaddr $dtbfile; "                                \
 672         "cramfsload $kerneladdr $kernelfile\0"                          \
 673 "norloadworking=mw.l $kerneladdr 0x0 0x00a00000; "                      \
 674         "setenv cramfsaddr $nor_workingaddr; "                          \
 675         "cramfsload $dtbaddr $dtbfile; "                                \
 676         "cramfsload $kerneladdr $kernelfile\0"                          \
 677 "othbootargs=quiet\0"                                                   \
 678 "ramboot=setenv bootargs root=/dev/ram ramdisk_size=$ramdisk_size ro"   \
 679         " console=$consoledev,$baudrate $othbootargs; "                 \
 680         "tftp $rootfsaddr $rootfsfile; "                                \
 681         "tftp $loadaddr $kernelfile; "                                  \
 682         "tftp $dtbaddr $dtbfile; "                                      \
 683         "bootm $loadaddr $rootfsaddr $dtbaddr\0"                        \
 684 "ramdisk_size=120000\0"                                                 \
 685 "ramdiskfile=rootfs.ext2.gz.uboot\0"                                    \
 686 "recoveryaddr=0x02F00000\0"                                             \
 687 "recoverybootargs=root=/dev/mtdblock0 rootfstype=cramfs ro\0"           \
 688 "releasefpga=mw.l 0xffe0f000 0x00400000; mw.l 0xffe0f004 0x00000000; "  \
 689         "mw.l 0xffe0f008 0x00400000\0"                                  \
 690 "rootfsaddr=0x02F00000\0"                                               \
 691 "rootfsfile=rootfs.ext2.gz.uboot\0"                                     \
 692 "rootpath=/opt/nfsroot\0"                                               \
 693 "silent=1\0"                                                            \
 694 "tftpflash=tftpboot $loadaddr $uboot; "                                 \
 695         "protect off " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
 696         "erase " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; "  \
 697         "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize; " \
 698         "protect on " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
 699         "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize\0"\
 700 "uboot= " __stringify(CONFIG_UBOOTPATH) "\0"                            \
 701 "ubootaddr=0x01000000\0"                                                \
 702 "ubootfile=u-boot.bin\0"                                                \
 703 "upgrade=run flashworking\0"                                            \
 704 "workingaddr=0x02F00000\0"                                              \
 705 "workingbootargs=root=/dev/mtdblock1 rootfstype=cramfs ro\0"
 706
 707 #else /* For Arcturus Modules */
 708
 709 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
 710 "bootcmd=run norkernel\0"                                               \
 711 "bootfile=uImage\0"                                                     \
 712 "consoledev=ttyS0\0"                                                    \
 713 "dtbaddr=0x00c00000\0"                                                  \
 714 "dtbfile=image.dtb\0"                                                   \
 715 "ethaddr=" __stringify(CONFIG_ETHADDR) "\0"                             \
 716 "eth1addr=" __stringify(CONFIG_ETH1ADDR) "\0"                           \
 717 "eth2addr=" __stringify(CONFIG_ETH2ADDR) "\0"                           \
 718 "fileaddr=0x01000000\0"                                                 \
 719 "filesize=0x00080000\0"                                                 \
 720 "flashmbr=sf probe 0; "                                                 \
 721         "tftp $loadaddr $mbr; "                                         \
 722         "sf erase $mbr_offset +$filesize; "                             \
 723         "sf write $loadaddr $mbr_offset $filesize\0"                    \
 724 "flashuboot=tftp $loadaddr $ubootfile; "                                \
 725         "protect off $nor_ubootaddr0 +$filesize; "                      \
 726         "erase $nor_ubootaddr0 +$filesize; "                            \
 727         "cp.b $loadaddr $nor_ubootaddr0 $filesize; "                    \
 728         "protect on $nor_ubootaddr0 +$filesize; "                       \
 729         "protect off $nor_ubootaddr1 +$filesize; "                      \
 730         "erase $nor_ubootaddr1 +$filesize; "                            \
 731         "cp.b $loadaddr $nor_ubootaddr1 $filesize; "                    \
 732         "protect on $nor_ubootaddr1 +$filesize\0 "                      \
 733 "format0=protect off $part0base +$part0size; "                          \
 734         "erase $part0base +$part0size\0"                                \
 735 "format1=protect off $part1base +$part1size; "                          \
 736         "erase $part1base +$part1size\0"                                \
 737 "format2=protect off $part2base +$part2size; "                          \
 738         "erase $part2base +$part2size\0"                                \
 739 "format3=protect off $part3base +$part3size; "                          \
 740         "erase $part3base +$part3size\0"                                \
 741 "hwconfig=usb1:dr_mode=host,phy_type=ulpi\0 "                           \
 742 "kerneladdr=0x01100000\0"                                               \
 743 "kernelargs=root=/dev/mtdblock1 rootfstype=cramfs ro\0"                 \
 744 "kernelfile=uImage\0"                                                   \
 745 "loadaddr=0x01000000\0"                                                 \
 746 "mbr=uCP1020.mbr\0"                                                     \
 747 "mbr_offset=0x00000000\0"                                               \
 748 "netdev=eth0\0"                                                         \
 749 "nor_ubootaddr0=0xEC000000\0"                                           \
 750 "nor_ubootaddr1=0xEFF80000\0"                                           \
 751 "norkernel=setenv bootargs $kernelargs console=$consoledev,$baudrate; " \
 752         "run norkernelload; "                                           \
 753         "bootm $kerneladdr - $dtbaddr\0"                                \
 754 "norkernelload=mw.l $kerneladdr 0x0 0x00a00000; "                       \
 755         "setenv cramfsaddr $part0base; "                                \
 756         "cramfsload $dtbaddr $dtbfile; "                                \
 757         "cramfsload $kerneladdr $kernelfile\0"                          \
 758 "part0base=0xEC100000\0"                                                \
 759 "part0size=0x00700000\0"                                                \
 760 "part1base=0xEC800000\0"                                                \
 761 "part1size=0x02000000\0"                                                \
 762 "part2base=0xEE800000\0"                                                \
 763 "part2size=0x00800000\0"                                                \
 764 "part3base=0xEF000000\0"                                                \
 765 "part3size=0x00F80000\0"                                                \
 766 "partENVbase=0xEC080000\0"                                              \
 767 "partENVsize=0x00080000\0"                                              \
 768 "program0=tftp part0-000000.bin; "                                      \
 769         "protect off $part0base +$filesize; "                           \
 770         "erase $part0base +$filesize; "                                 \
 771         "cp.b $loadaddr $part0base $filesize; "                         \
 772         "echo Verifying...; "                                           \
 773         "cmp.b $loadaddr $part0base $filesize\0"                        \
 774 "program1=tftp part1-000000.bin; "                                      \
 775         "protect off $part1base +$filesize; "                           \
 776         "erase $part1base +$filesize; "                                 \
 777         "cp.b $loadaddr $part1base $filesize; "                         \
 778         "echo Verifying...; "                                           \
 779         "cmp.b $loadaddr $part1base $filesize\0"                        \
 780 "program2=tftp part2-000000.bin; "                                      \
 781         "protect off $part2base +$filesize; "                           \
 782         "erase $part2base +$filesize; "                                 \
 783         "cp.b $loadaddr $part2base $filesize; "                         \
 784         "echo Verifying...; "                                           \
 785         "cmp.b $loadaddr $part2base $filesize\0"                        \
 786 "ramboot=setenv bootargs root=/dev/ram ramdisk_size=$ramdisk_size ro"   \
 787         "  console=$consoledev,$baudrate $othbootargs; "                \
 788         "tftp $rootfsaddr $rootfsfile; "                                \
 789         "tftp $loadaddr $kernelfile; "                                  \
 790         "tftp $dtbaddr $dtbfile; "                                      \
 791         "bootm $loadaddr $rootfsaddr $dtbaddr\0"                        \
 792 "ramdisk_size=120000\0"                                                 \
 793 "ramdiskfile=rootfs.ext2.gz.uboot\0"                                    \
 794 "releasefpga=mw.l 0xffe0f000 0x00400000; mw.l 0xffe0f004 0x00000000; "  \
 795         "mw.l 0xffe0f008 0x00400000\0"                                  \
 796 "rootfsaddr=0x02F00000\0"                                               \
 797 "rootfsfile=rootfs.ext2.gz.uboot\0"                                     \
 798 "rootpath=/opt/nfsroot\0"                                               \
 799 "spi__mbr=fatload mmc $mmcpart $loadaddr $mmbr; "                       \
 800         "sf probe 0; sf erase 0 +$filesize; "                           \
 801         "sf write $loadaddr 0 $filesize\0"                              \
 802 "spi__boot=fatload mmc $mmcpart $loadaddr u-boot.bin; "                 \
 803         "protect off 0xeC000000 +$filesize; "                           \
 804         "erase 0xEC000000 +$filesize; "                                 \
 805         "cp.b $loadaddr 0xEC000000 $filesize; "                         \
 806         "cmp.b $loadaddr 0xEC000000 $filesize; "                        \
 807         "protect on 0xeC000000 +$filesize\0"                            \
 808 "tftpflash=tftpboot $loadaddr $uboot; "                                 \
 809         "protect off " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
 810         "erase " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; "  \
 811         "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize; " \
 812         "protect on " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
 813         "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize\0"\
 814 "uboot= " __stringify(CONFIG_UBOOTPATH) "\0"                            \
 815 "ubootfile=u-boot.bin\0"                                                \
 816 "upgrade=run flashuboot\0"                                              \
 817 "usb_phy_type=ulpi\0 "                                                  \
 818 "boot_nfs= "                                                            \
 819         "setenv bootargs root=/dev/nfs rw "                             \
 820         "nfsroot=$serverip:$rootpath "                                  \
 821         "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
 822         "console=$consoledev,$baudrate $othbootargs;"                   \
 823         "tftp $loadaddr $bootfile;"                                     \
 824         "tftp $fdtaddr $fdtfile;"                                       \
 825         "bootm $loadaddr - $fdtaddr\0"                                  \
 826 "boot_hd = "                                                            \
 827         "setenv bootargs root=/dev/$bdev rw rootdelay=30 "              \
 828         "console=$consoledev,$baudrate $othbootargs;"                   \
 829         "usb start;"                                                    \
 830         "ext2load usb 0:1 $loadaddr /boot/$bootfile;"                   \
 831         "ext2load usb 0:1 $fdtaddr /boot/$fdtfile;"                     \
 832         "bootm $loadaddr - $fdtaddr\0"                                  \
 833 "boot_usb_fat = "                                                       \
 834         "setenv bootargs root=/dev/ram rw "                             \
 835         "console=$consoledev,$baudrate $othbootargs "                   \
 836         "ramdisk_size=$ramdisk_size;"                                   \
 837         "usb start;"                                                    \
 838         "fatload usb 0:2 $loadaddr $bootfile;"                          \
 839         "fatload usb 0:2 $fdtaddr $fdtfile;"                            \
 840         "fatload usb 0:2 $ramdiskaddr $ramdiskfile;"                    \
 841         "bootm $loadaddr $ramdiskaddr $fdtaddr\0 "                      \
 842 "boot_usb_ext2 = "                                                      \
 843         "setenv bootargs root=/dev/ram rw "                             \
 844         "console=$consoledev,$baudrate $othbootargs "                   \
 845         "ramdisk_size=$ramdisk_size;"                                   \
 846         "usb start;"                                                    \
 847         "ext2load usb 0:4 $loadaddr $bootfile;"                         \
 848         "ext2load usb 0:4 $fdtaddr $fdtfile;"                           \
 849         "ext2load usb 0:4 $ramdiskaddr $ramdiskfile;"                   \
 850         "bootm $loadaddr $ramdiskaddr $fdtaddr\0 "                      \
 851 "boot_nor = "                                                           \
 852         "setenv bootargs root=/dev/$jffs2nor rw "                       \
 853         "console=$consoledev,$baudrate rootfstype=jffs2 $othbootargs;"  \
 854         "bootm $norbootaddr - $norfdtaddr\0 "                           \
 855 "boot_ram = "                                                           \
 856         "setenv bootargs root=/dev/ram rw "                             \
 857         "console=$consoledev,$baudrate $othbootargs "                   \
 858         "ramdisk_size=$ramdisk_size;"                                   \
 859         "tftp $ramdiskaddr $ramdiskfile;"                               \
 860         "tftp $loadaddr $bootfile;"                                     \
 861         "tftp $fdtaddr $fdtfile;"                                       \
 862         "bootm $loadaddr $ramdiskaddr $fdtaddr\0"
 863
 864 #endif
 865 #endif
 866
 867 #endif /* __CONFIG_H */