include/configs/UCP1020.h

   1 /*
   2  * Copyright 2013-2015 Arcturus Networks, Inc.
   3  *           http://www.arcturusnetworks.com/products/ucp1020/
   4  * based on include/configs/p1_p2_rdb_pc.h
   5  * original copyright follows:
   6  * Copyright 2009-2011 Freescale Semiconductor, Inc.
   7  *
   8  * SPDX-License-Identifier:     GPL-2.0+
   9  */
  10
  11 /*
  12  * QorIQ uCP1020-xx boards configuration file
  13  */
  14 #ifndef __CONFIG_H
  15 #define __CONFIG_H
  16
  17 #define CONFIG_FSL_ELBC
  18 #define CONFIG_PCIE1    /* PCIE controller 1 (slot 1) */
  19 #define CONFIG_PCIE2    /* PCIE controller 2 (slot 2) */
  20 #define CONFIG_FSL_PCI_INIT     /* Use common FSL init code */
  21 #define CONFIG_PCI_INDIRECT_BRIDGE      /* indirect PCI bridge support */
  22 #define CONFIG_FSL_PCIE_RESET   /* need PCIe reset errata */
  23 #define CONFIG_SYS_PCI_64BIT    /* enable 64-bit PCI resources */
  24
  25 #if defined(CONFIG_TARTGET_UCP1020T1)
  26
  27 #define CONFIG_UCP1020_REV_1_3
  28
  29 #define CONFIG_BOARDNAME "uCP1020-64EE512-0U1-XR-T1"
  30
  31 #define CONFIG_TSEC_ENET
  32 #define CONFIG_TSEC1
  33 #define CONFIG_TSEC3
  34 #define CONFIG_HAS_ETH0
  35 #define CONFIG_HAS_ETH1
  36 #define CONFIG_ETHADDR          00:19:D3:FF:FF:FF
  37 #define CONFIG_ETH1ADDR         00:19:D3:FF:FF:FE
  38 #define CONFIG_ETH2ADDR         00:19:D3:FF:FF:FD
  39 #define CONFIG_IPADDR           10.80.41.229
  40 #define CONFIG_SERVERIP         10.80.41.227
  41 #define CONFIG_NETMASK          255.255.252.0
  42 #define CONFIG_ETHPRIME         "eTSEC3"
  43
  44 #ifndef CONFIG_SPI_FLASH
  45 #endif
  46 #define CONFIG_SYS_REDUNDAND_ENVIRONMENT
  47
  48 #define CONFIG_MMC
  49 #define CONFIG_SYS_L2_SIZE      (256 << 10)
  50
  51 #define CONFIG_LAST_STAGE_INIT
  52
  53 #endif
  54
  55 #if defined(CONFIG_TARGET_UCP1020)
  56
  57 #define CONFIG_UCP1020
  58 #define CONFIG_UCP1020_REV_1_3
  59
  60 #define CONFIG_BOARDNAME_LOCAL "uCP1020-64EEE512-OU1-XR"
  61
  62 #define CONFIG_TSEC_ENET
  63 #define CONFIG_TSEC1
  64 #define CONFIG_TSEC2
  65 #define CONFIG_TSEC3
  66 #define CONFIG_HAS_ETH0
  67 #define CONFIG_HAS_ETH1
  68 #define CONFIG_HAS_ETH2
  69 #define CONFIG_ETHADDR          00:06:3B:FF:FF:FF
  70 #define CONFIG_ETH1ADDR         00:06:3B:FF:FF:FE
  71 #define CONFIG_ETH2ADDR         00:06:3B:FF:FF:FD
  72 #define CONFIG_IPADDR           192.168.1.81
  73 #define CONFIG_IPADDR1          192.168.1.82
  74 #define CONFIG_IPADDR2          192.168.1.83
  75 #define CONFIG_SERVERIP         192.168.1.80
  76 #define CONFIG_GATEWAYIP        102.168.1.1
  77 #define CONFIG_NETMASK          255.255.255.0
  78 #define CONFIG_ETHPRIME         "eTSEC1"
  79
  80 #ifndef CONFIG_SPI_FLASH
  81 #endif
  82 #define CONFIG_SYS_REDUNDAND_ENVIRONMENT
  83
  84 #define CONFIG_MMC
  85 #define CONFIG_SYS_L2_SIZE      (256 << 10)
  86
  87 #define CONFIG_LAST_STAGE_INIT
  88
  89 #endif
  90
  91 #ifdef CONFIG_SDCARD
  92 #define CONFIG_RAMBOOT_SDCARD
  93 #define CONFIG_SYS_RAMBOOT
  94 #define CONFIG_SYS_EXTRA_ENV_RELOC
  95 #define CONFIG_SYS_TEXT_BASE            0x11000000
  96 #define CONFIG_RESET_VECTOR_ADDRESS     0x1107fffc
  97 #endif
  98
  99 #ifdef CONFIG_SPIFLASH
 100 #define CONFIG_RAMBOOT_SPIFLASH
 101 #define CONFIG_SYS_RAMBOOT
 102 #define CONFIG_SYS_EXTRA_ENV_RELOC
 103 #define CONFIG_SYS_TEXT_BASE            0x11000000
 104 #define CONFIG_RESET_VECTOR_ADDRESS     0x1107fffc
 105 #endif
 106
 107 #ifndef CONFIG_SYS_TEXT_BASE
 108 #define CONFIG_SYS_TEXT_BASE            0xeff80000
 109 #endif
 110 #define CONFIG_SYS_TEXT_BASE_NOR        0xeff80000
 111
 112 #ifndef CONFIG_RESET_VECTOR_ADDRESS
 113 #define CONFIG_RESET_VECTOR_ADDRESS     0xeffffffc
 114 #endif
 115
 116 #ifndef CONFIG_SYS_MONITOR_BASE
 117 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE    /* start of monitor */
 118 #endif
 119
 120 /* High Level Configuration Options */
 121 #define CONFIG_BOOKE
 122 #define CONFIG_E500
 123 /* #define CONFIG_MPC85xx */
 124
 125 #define CONFIG_MP
 126
 127 #define CONFIG_ENV_OVERWRITE
 128
 129 #define CONFIG_CMD_SATA
 130 #define CONFIG_SATA_SIL
 131 #define CONFIG_SYS_SATA_MAX_DEVICE      2
 132 #define CONFIG_LIBATA
 133 #define CONFIG_LBA48
 134
 135 #define CONFIG_SYS_CLK_FREQ     66666666
 136 #define CONFIG_DDR_CLK_FREQ     66666666
 137
 138 #define CONFIG_HWCONFIG
 139
 140 #define CONFIG_DTT_ADM1021      1       /* ADM1021 temp sensor support  */
 141 #define CONFIG_SYS_DTT_BUS_NUM  1       /* The I2C bus for DTT          */
 142 #define CONFIG_DTT_SENSORS      { 0, 1 }        /* Sensor index */
 143 /*
 144  * ADM1021/NCT72 temp sensor configuration (see dtt/adm1021.c for details).
 145  * there will be one entry in this array for each two (dummy) sensors in
 146  * CONFIG_DTT_SENSORS.
 147  *
 148  * For uCP1020 module:
 149  * - only one ADM1021/NCT72
 150  * - i2c addr 0x41
 151  * - conversion rate 0x02 = 0.25 conversions/second
 152  * - ALERT output disabled
 153  * - local temp sensor enabled, min set to 0 deg, max set to 85 deg
 154  * - remote temp sensor enabled, min set to 0 deg, max set to 85 deg
 155  */
 156 #define CONFIG_SYS_DTT_ADM1021  { { CONFIG_SYS_I2C_NCT72_ADDR, \
 157                                          0x02, 0, 1, 0, 85, 1, 0, 85} }
 158
 159 #define CONFIG_CMD_DTT
 160
 161 /*
 162  * These can be toggled for performance analysis, otherwise use default.
 163  */
 164 #define CONFIG_L2_CACHE
 165 #define CONFIG_BTB
 166
 167 #define CONFIG_BOARD_EARLY_INIT_F       /* Call board_pre_init */
 168
 169 #define CONFIG_ENABLE_36BIT_PHYS
 170
 171 #define CONFIG_SYS_MEMTEST_START        0x00200000      /* memtest works on */
 172 #define CONFIG_SYS_MEMTEST_END          0x1fffffff
 173 #define CONFIG_PANIC_HANG       /* do not reset board on panic */
 174
 175 #define CONFIG_SYS_CCSRBAR              0xffe00000
 176 #define CONFIG_SYS_CCSRBAR_PHYS_LOW     CONFIG_SYS_CCSRBAR
 177
 178 /* IN case of NAND bootloader relocate CCSRBAR in RAMboot code not in the 4k
 179        SPL code*/
 180 #ifdef CONFIG_SPL_BUILD
 181 #define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
 182 #endif
 183
 184 /* DDR Setup */
 185 #define CONFIG_DDR_ECC_ENABLE
 186 #define CONFIG_SYS_FSL_DDR3
 187 #ifndef CONFIG_DDR_ECC_ENABLE
 188 #define CONFIG_SYS_DDR_RAW_TIMING
 189 #define CONFIG_DDR_SPD
 190 #endif
 191 #define CONFIG_SYS_SPD_BUS_NUM 1
 192 #undef CONFIG_FSL_DDR_INTERACTIVE
 193
 194 #define CONFIG_SYS_SDRAM_SIZE_LAW       LAW_SIZE_512M
 195 #define CONFIG_CHIP_SELECTS_PER_CTRL    1
 196 #define CONFIG_SYS_SDRAM_SIZE           (1u << (CONFIG_SYS_SDRAM_SIZE_LAW - 19))
 197 #define CONFIG_SYS_DDR_SDRAM_BASE       0x00000000
 198 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE
 199
 200 #define CONFIG_NUM_DDR_CONTROLLERS      1
 201 #define CONFIG_DIMM_SLOTS_PER_CTLR      1
 202
 203 /* Default settings for DDR3 */
 204 #define CONFIG_SYS_DDR_CS0_BNDS         0x0000003f
 205 #define CONFIG_SYS_DDR_CS0_CONFIG       0x80014302
 206 #define CONFIG_SYS_DDR_CS0_CONFIG_2     0x00000000
 207 #define CONFIG_SYS_DDR_CS1_BNDS         0x0040007f
 208 #define CONFIG_SYS_DDR_CS1_CONFIG       0x80014302
 209 #define CONFIG_SYS_DDR_CS1_CONFIG_2     0x00000000
 210
 211 #define CONFIG_SYS_DDR_DATA_INIT        0xdeadbeef
 212 #define CONFIG_SYS_DDR_INIT_ADDR        0x00000000
 213 #define CONFIG_SYS_DDR_INIT_EXT_ADDR    0x00000000
 214 #define CONFIG_SYS_DDR_MODE_CONTROL     0x00000000
 215
 216 #define CONFIG_SYS_DDR_ZQ_CONTROL       0x89080600
 217 #define CONFIG_SYS_DDR_WRLVL_CONTROL    0x8655A608
 218 #define CONFIG_SYS_DDR_SR_CNTR          0x00000000
 219 #define CONFIG_SYS_DDR_RCW_1            0x00000000
 220 #define CONFIG_SYS_DDR_RCW_2            0x00000000
 221 #ifdef CONFIG_DDR_ECC_ENABLE
 222 #define CONFIG_SYS_DDR_CONTROL          0xE70C0000      /* Type = DDR3 & ECC */
 223 #else
 224 #define CONFIG_SYS_DDR_CONTROL          0xC70C0000      /* Type = DDR3 */
 225 #endif
 226 #define CONFIG_SYS_DDR_CONTROL_2        0x04401050
 227 #define CONFIG_SYS_DDR_TIMING_4         0x00220001
 228 #define CONFIG_SYS_DDR_TIMING_5         0x03402400
 229
 230 #define CONFIG_SYS_DDR_TIMING_3         0x00020000
 231 #define CONFIG_SYS_DDR_TIMING_0         0x00330004
 232 #define CONFIG_SYS_DDR_TIMING_1         0x6f6B4846
 233 #define CONFIG_SYS_DDR_TIMING_2         0x0FA8C8CF
 234 #define CONFIG_SYS_DDR_CLK_CTRL         0x03000000
 235 #define CONFIG_SYS_DDR_MODE_1           0x40461520
 236 #define CONFIG_SYS_DDR_MODE_2           0x8000c000
 237 #define CONFIG_SYS_DDR_INTERVAL         0x0C300000
 238
 239 #undef CONFIG_CLOCKS_IN_MHZ
 240
 241 /*
 242  * Memory map
 243  *
 244  * 0x0000_0000 0x7fff_ffff      DDR             Up to 2GB cacheable
 245  * 0x8000_0000 0xdfff_ffff      PCI Express Mem 1G non-cacheable(PCIe * 2)
 246  * 0xec00_0000 0xefff_ffff      NOR flash       Up to 64M non-cacheable CS0/1
 247  * 0xf8f8_0000 0xf8ff_ffff      L2 SRAM         Up to 256K cacheable
 248  *   (early boot only)
 249  * 0xffc0_0000 0xffc3_ffff      PCI IO range    256k non-cacheable
 250  * 0xffd0_0000 0xffd0_3fff      L1 for stack    16K cacheable
 251  * 0xffe0_0000 0xffef_ffff      CCSR            1M non-cacheable
 252  */
 253
 254 /*
 255  * Local Bus Definitions
 256  */
 257 #define CONFIG_SYS_MAX_FLASH_SECT       512     /* 64M */
 258 #define CONFIG_SYS_FLASH_BASE           0xec000000
 259
 260 #define CONFIG_SYS_FLASH_BASE_PHYS      CONFIG_SYS_FLASH_BASE
 261
 262 #define CONFIG_FLASH_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \
 263         | BR_PS_16 | BR_V)
 264
 265 #define CONFIG_FLASH_OR_PRELIM          0xfc000ff7
 266
 267 #define CONFIG_SYS_FLASH_BANKS_LIST     {CONFIG_SYS_FLASH_BASE_PHYS}
 268 #define CONFIG_SYS_FLASH_QUIET_TEST
 269 #define CONFIG_FLASH_SHOW_PROGRESS      45      /* count down from 45/5: 9..1 */
 270
 271 #define CONFIG_SYS_MAX_FLASH_BANKS      1       /* number of banks */
 272
 273 #undef CONFIG_SYS_FLASH_CHECKSUM
 274 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000   /* Flash Erase Timeout (ms) */
 275 #define CONFIG_SYS_FLASH_WRITE_TOUT     500     /* Flash Write Timeout (ms) */
 276
 277 #define CONFIG_FLASH_CFI_DRIVER
 278 #define CONFIG_SYS_FLASH_CFI
 279 #define CONFIG_SYS_FLASH_EMPTY_INFO
 280 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
 281
 282 #define CONFIG_BOARD_EARLY_INIT_R       /* call board_early_init_r function */
 283
 284 #define CONFIG_SYS_INIT_RAM_LOCK
 285 #define CONFIG_SYS_INIT_RAM_ADDR        0xffd00000 /* stack in RAM */
 286 /* Initial L1 address */
 287 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS   CONFIG_SYS_INIT_RAM_ADDR
 288 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0
 289 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS
 290 /* Size of used area in RAM */
 291 #define CONFIG_SYS_INIT_RAM_SIZE        0x00004000
 292
 293 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - \
 294                                         GENERATED_GBL_DATA_SIZE)
 295 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 296
 297 #define CONFIG_SYS_MONITOR_LEN  (256 * 1024)/* Reserve 256 kB for Mon */
 298 #define CONFIG_SYS_MALLOC_LEN   (1024 * 1024)/* Reserved for malloc */
 299
 300 #define CONFIG_SYS_PMC_BASE     0xff980000
 301 #define CONFIG_SYS_PMC_BASE_PHYS        CONFIG_SYS_PMC_BASE
 302 #define CONFIG_PMC_BR_PRELIM    (BR_PHYS_ADDR(CONFIG_SYS_PMC_BASE_PHYS) | \
 303                                         BR_PS_8 | BR_V)
 304 #define CONFIG_PMC_OR_PRELIM    (OR_AM_64KB | OR_GPCM_CSNT | OR_GPCM_XACS | \
 305                                  OR_GPCM_SCY | OR_GPCM_TRLX | OR_GPCM_EHTR | \
 306                                  OR_GPCM_EAD)
 307
 308 #define CONFIG_SYS_BR0_PRELIM   CONFIG_FLASH_BR_PRELIM  /* NOR Base Address */
 309 #define CONFIG_SYS_OR0_PRELIM   CONFIG_FLASH_OR_PRELIM  /* NOR Options */
 310 #ifdef CONFIG_NAND_FSL_ELBC
 311 #define CONFIG_SYS_BR1_PRELIM   CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Addr */
 312 #define CONFIG_SYS_OR1_PRELIM   CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */
 313 #endif
 314
 315 /* Serial Port - controlled on board with jumper J8
 316  * open - index 2
 317  * shorted - index 1
 318  */
 319 #define CONFIG_CONS_INDEX               1
 320 #undef CONFIG_SERIAL_SOFTWARE_FIFO
 321 #define CONFIG_SYS_NS16550_SERIAL
 322 #define CONFIG_SYS_NS16550_REG_SIZE     1
 323 #define CONFIG_SYS_NS16550_CLK          get_bus_freq(0)
 324 #if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_INIT_MINIMAL)
 325 #define CONFIG_NS16550_MIN_FUNCTIONS
 326 #endif
 327
 328 #define CONFIG_SYS_BAUDRATE_TABLE       \
 329         {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
 330
 331 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR + 0x4500)
 332 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR + 0x4600)
 333
 334 /* I2C */
 335 #define CONFIG_SYS_I2C
 336 #define CONFIG_SYS_I2C_FSL
 337 #define CONFIG_SYS_FSL_I2C_SPEED        400000
 338 #define CONFIG_SYS_FSL_I2C_SLAVE        0x7F
 339 #define CONFIG_SYS_FSL_I2C_OFFSET       0x3000
 340 #define CONFIG_SYS_FSL_I2C2_SPEED       400000
 341 #define CONFIG_SYS_FSL_I2C2_SLAVE       0x7F
 342 #define CONFIG_SYS_FSL_I2C2_OFFSET      0x3100
 343 #define CONFIG_SYS_I2C_NOPROBES         { {0, 0x29} }
 344 #define CONFIG_SYS_SPD_BUS_NUM          1 /* For rom_loc and flash bank */
 345
 346 #define CONFIG_RTC_DS1337
 347 #define CONFIG_SYS_RTC_DS1337_NOOSC
 348 #define CONFIG_SYS_I2C_RTC_ADDR         0x68
 349 #define CONFIG_SYS_I2C_PCA9557_ADDR     0x18
 350 #define CONFIG_SYS_I2C_NCT72_ADDR       0x4C
 351 #define CONFIG_SYS_I2C_IDT6V49205B      0x69
 352
 353 /*
 354  * eSPI - Enhanced SPI
 355  */
 356 #define CONFIG_HARD_SPI
 357
 358 #define CONFIG_SF_DEFAULT_SPEED         10000000
 359 #define CONFIG_SF_DEFAULT_MODE          SPI_MODE_0
 360
 361 #if defined(CONFIG_PCI)
 362 /*
 363  * General PCI
 364  * Memory space is mapped 1-1, but I/O space must start from 0.
 365  */
 366
 367 /* controller 2, direct to uli, tgtid 2, Base address 9000 */
 368 #define CONFIG_SYS_PCIE2_NAME           "PCIe SLOT CON9"
 369 #define CONFIG_SYS_PCIE2_MEM_VIRT       0xa0000000
 370 #define CONFIG_SYS_PCIE2_MEM_BUS        0xa0000000
 371 #define CONFIG_SYS_PCIE2_MEM_PHYS       0xa0000000
 372 #define CONFIG_SYS_PCIE2_MEM_SIZE       0x20000000      /* 512M */
 373 #define CONFIG_SYS_PCIE2_IO_VIRT        0xffc10000
 374 #define CONFIG_SYS_PCIE2_IO_BUS         0x00000000
 375 #define CONFIG_SYS_PCIE2_IO_PHYS        0xffc10000
 376 #define CONFIG_SYS_PCIE2_IO_SIZE        0x00010000      /* 64k */
 377
 378 /* controller 1, Slot 2, tgtid 1, Base address a000 */
 379 #define CONFIG_SYS_PCIE1_NAME           "PCIe SLOT CON10"
 380 #define CONFIG_SYS_PCIE1_MEM_VIRT       0x80000000
 381 #define CONFIG_SYS_PCIE1_MEM_BUS        0x80000000
 382 #define CONFIG_SYS_PCIE1_MEM_PHYS       0x80000000
 383 #define CONFIG_SYS_PCIE1_MEM_SIZE       0x20000000      /* 512M */
 384 #define CONFIG_SYS_PCIE1_IO_VIRT        0xffc00000
 385 #define CONFIG_SYS_PCIE1_IO_BUS         0x00000000
 386 #define CONFIG_SYS_PCIE1_IO_PHYS        0xffc00000
 387 #define CONFIG_SYS_PCIE1_IO_SIZE        0x00010000      /* 64k */
 388
 389 #define CONFIG_CMD_PCI
 390
 391 #define CONFIG_PCI_SCAN_SHOW    /* show pci devices on startup */
 392 #define CONFIG_DOS_PARTITION
 393 #endif /* CONFIG_PCI */
 394
 395 /*
 396  * Environment
 397  */
 398 #ifdef CONFIG_ENV_FIT_UCBOOT
 399
 400 #define CONFIG_ENV_IS_IN_FLASH
 401 #define CONFIG_ENV_ADDR         (CONFIG_SYS_FLASH_BASE + 0x20000)
 402 #define CONFIG_ENV_SIZE         0x20000
 403 #define CONFIG_ENV_SECT_SIZE    0x20000 /* 128K (one sector) */
 404
 405 #else
 406
 407 #define CONFIG_ENV_SPI_BUS      0
 408 #define CONFIG_ENV_SPI_CS       0
 409 #define CONFIG_ENV_SPI_MAX_HZ   10000000
 410 #define CONFIG_ENV_SPI_MODE     0
 411
 412 #ifdef CONFIG_RAMBOOT_SPIFLASH
 413
 414 #define CONFIG_ENV_IS_IN_SPI_FLASH
 415 #define CONFIG_ENV_SIZE         0x3000          /* 12KB */
 416 #define CONFIG_ENV_OFFSET       0x2000          /* 8KB */
 417 #define CONFIG_ENV_SECT_SIZE    0x1000
 418
 419 #if defined(CONFIG_SYS_REDUNDAND_ENVIRONMENT)
 420 /* Address and size of Redundant Environment Sector     */
 421 #define CONFIG_ENV_OFFSET_REDUND        (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
 422 #define CONFIG_ENV_SIZE_REDUND          CONFIG_ENV_SIZE
 423 #endif
 424
 425 #elif defined(CONFIG_RAMBOOT_SDCARD)
 426 #define CONFIG_ENV_IS_IN_MMC
 427 #define CONFIG_FSL_FIXED_MMC_LOCATION
 428 #define CONFIG_ENV_SIZE         0x2000
 429 #define CONFIG_SYS_MMC_ENV_DEV  0
 430
 431 #elif defined(CONFIG_SYS_RAMBOOT)
 432 #define CONFIG_ENV_IS_NOWHERE   /* Store ENV in memory only */
 433 #define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE - 0x1000)
 434 #define CONFIG_ENV_SIZE         0x2000
 435
 436 #else
 437 #define CONFIG_ENV_IS_IN_FLASH
 438 #define CONFIG_ENV_BASE         (CONFIG_SYS_FLASH_BASE)
 439 #define CONFIG_ENV_SECT_SIZE    0x20000 /* 128K (one sector) */
 440 #define CONFIG_ENV_SIZE         CONFIG_ENV_SECT_SIZE
 441 #define CONFIG_ENV_ADDR         (CONFIG_ENV_BASE + 0xC0000)
 442 #if defined(CONFIG_SYS_REDUNDAND_ENVIRONMENT)
 443 /* Address and size of Redundant Environment Sector     */
 444 #define CONFIG_ENV_ADDR_REDUND  (CONFIG_ENV_ADDR + CONFIG_ENV_SIZE)
 445 #define CONFIG_ENV_SIZE_REDUND  CONFIG_ENV_SIZE
 446 #endif
 447
 448 #endif
 449
 450 #endif  /* CONFIG_ENV_FIT_UCBOOT */
 451
 452 #define CONFIG_LOADS_ECHO               /* echo on for serial download */
 453 #define CONFIG_SYS_LOADS_BAUD_CHANGE    /* allow baudrate change */
 454
 455 /*
 456  * Command line configuration.
 457  */
 458 #define CONFIG_CMD_IRQ
 459 #define CONFIG_CMD_DATE
 460 #define CONFIG_CMD_IRQ
 461 #define CONFIG_CMD_REGINFO
 462 #define CONFIG_CMD_ERRATA
 463 #define CONFIG_CMD_CRAMFS
 464
 465 /*
 466  * USB
 467  */
 468 #define CONFIG_HAS_FSL_DR_USB
 469
 470 #if defined(CONFIG_HAS_FSL_DR_USB)
 471 #define CONFIG_USB_EHCI
 472
 473 #define CONFIG_USB_MAX_CONTROLLER_COUNT 1
 474
 475 #ifdef CONFIG_USB_EHCI
 476 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 477 #define CONFIG_USB_EHCI_FSL
 478 #endif
 479 #endif
 480
 481 #undef CONFIG_WATCHDOG                  /* watchdog disabled */
 482
 483 #ifdef CONFIG_MMC
 484 #define CONFIG_FSL_ESDHC
 485 #define CONFIG_SYS_FSL_ESDHC_ADDR       CONFIG_SYS_MPC85xx_ESDHC_ADDR
 486 #define CONFIG_MMC_SPI
 487 #define CONFIG_CMD_MMC_SPI
 488 #define CONFIG_GENERIC_MMC
 489 #endif
 490
 491 #if defined(CONFIG_MMC) || defined(CONFIG_USB_EHCI) || defined(CONFIG_FSL_SATA)
 492 #define CONFIG_DOS_PARTITION
 493 #endif
 494
 495 /* Misc Extra Settings */
 496 #undef CONFIG_WATCHDOG  /* watchdog disabled */
 497
 498 /*
 499  * Miscellaneous configurable options
 500  */
 501 #define CONFIG_SYS_LONGHELP                     /* undef to save memory */
 502 #define CONFIG_CMDLINE_EDITING                  /* Command-line editing */
 503 #define CONFIG_SYS_LOAD_ADDR    0x2000000       /* default load address */
 504 #if defined(CONFIG_CMD_KGDB)
 505 #define CONFIG_SYS_CBSIZE       1024            /* Console I/O Buffer Size */
 506 #else
 507 #define CONFIG_SYS_CBSIZE       256             /* Console I/O Buffer Size */
 508 #endif
 509 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
 510         /* Print Buffer Size */
 511 #define CONFIG_SYS_MAXARGS      16      /* max number of command args */
 512 #define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */
 513 #define CONFIG_SYS_HZ           1000    /* decrementer freq: 1ms tick */
 514
 515 /*
 516  * For booting Linux, the board info and command line data
 517  * have to be in the first 64 MB of memory, since this is
 518  * the maximum mapped by the Linux kernel during initialization.
 519  */
 520 #define CONFIG_SYS_BOOTMAPSZ    (64 << 20)      /* Initial Memory for Linux*/
 521 #define CONFIG_SYS_BOOTM_LEN    (64 << 20)      /* Increase max gunzip size */
 522
 523 #if defined(CONFIG_CMD_KGDB)
 524 #define CONFIG_KGDB_BAUDRATE    230400  /* speed to run kgdb serial port */
 525 #define CONFIG_KGDB_SER_INDEX   2       /* which serial port to use */
 526 #endif
 527
 528 /*
 529  * Environment Configuration
 530  */
 531
 532 #if defined(CONFIG_TSEC_ENET)
 533
 534 #if defined(CONFIG_UCP1020_REV_1_2)
 535 #define CONFIG_PHY_MICREL_KSZ9021
 536 #elif defined(CONFIG_UCP1020_REV_1_3)
 537 #define CONFIG_PHY_MICREL_KSZ9031
 538 #else
 539 #error "UCP1020 module revision is not defined !!!"
 540 #endif
 541
 542 #define CONFIG_BOOTP_SERVERIP
 543
 544 #define CONFIG_MII              /* MII PHY management */
 545 #define CONFIG_TSEC1_NAME       "eTSEC1"
 546 #define CONFIG_TSEC2_NAME       "eTSEC2"
 547 #define CONFIG_TSEC3_NAME       "eTSEC3"
 548
 549 #define TSEC1_PHY_ADDR  4
 550 #define TSEC2_PHY_ADDR  0
 551 #define TSEC2_PHY_ADDR_SGMII    0x00
 552 #define TSEC3_PHY_ADDR  6
 553
 554 #define TSEC1_FLAGS     (TSEC_GIGABIT | TSEC_REDUCED)
 555 #define TSEC2_FLAGS     (TSEC_GIGABIT | TSEC_REDUCED)
 556 #define TSEC3_FLAGS     (TSEC_GIGABIT | TSEC_REDUCED)
 557
 558 #define TSEC1_PHYIDX    0
 559 #define TSEC2_PHYIDX    0
 560 #define TSEC3_PHYIDX    0
 561
 562 #define CONFIG_PHY_GIGE 1       /* Include GbE speed/duplex detection */
 563
 564 #endif
 565
 566 #define CONFIG_HOSTNAME         UCP1020
 567 #define CONFIG_ROOTPATH         "/opt/nfsroot"
 568 #define CONFIG_BOOTFILE         "uImage"
 569 #define CONFIG_UBOOTPATH        u-boot.bin /* U-Boot image on TFTP server */
 570
 571 /* default location for tftp and bootm */
 572 #define CONFIG_LOADADDR         1000000
 573
 574 #define CONFIG_BOOTARGS /* the boot command will set bootargs */
 575
 576 #define CONFIG_BAUDRATE 115200
 577
 578 #if defined(CONFIG_DONGLE)
 579
 580 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
 581 "bootcmd=run prog_spi_mbrbootcramfs\0"                                  \
 582 "bootfile=uImage\0"                                                     \
 583 "consoledev=ttyS0\0"                                                    \
 584 "cramfsfile=image.cramfs\0"                                             \
 585 "dtbaddr=0x00c00000\0"                                                  \
 586 "dtbfile=image.dtb\0"                                                   \
 587 "ethaddr=" __stringify(CONFIG_ETHADDR) "\0"                             \
 588 "eth1addr=" __stringify(CONFIG_ETH1ADDR) "\0"                           \
 589 "eth2addr=" __stringify(CONFIG_ETH2ADDR) "\0"                           \
 590 "fileaddr=0x01000000\0"                                                 \
 591 "filesize=0x00080000\0"                                                 \
 592 "flashmbr=sf probe 0; "                                                 \
 593         "tftp $loadaddr $mbr; "                                         \
 594         "sf erase $mbr_offset +$filesize; "                             \
 595         "sf write $loadaddr $mbr_offset $filesize\0"                    \
 596 "flashrecovery=tftp $recoveryaddr $cramfsfile; "                        \
 597         "protect off $nor_recoveryaddr +$filesize; "                    \
 598         "erase $nor_recoveryaddr +$filesize; "                          \
 599         "cp.b $recoveryaddr $nor_recoveryaddr $filesize; "              \
 600         "protect on $nor_recoveryaddr +$filesize\0 "                    \
 601 "flashuboot=tftp $ubootaddr $ubootfile; "                               \
 602         "protect off $nor_ubootaddr +$filesize; "                       \
 603         "erase $nor_ubootaddr +$filesize; "                             \
 604         "cp.b $ubootaddr $nor_ubootaddr $filesize; "                    \
 605         "protect on $nor_ubootaddr +$filesize\0 "                       \
 606 "flashworking=tftp $workingaddr $cramfsfile; "                          \
 607         "protect off $nor_workingaddr +$filesize; "                     \
 608         "erase $nor_workingaddr +$filesize; "                           \
 609         "cp.b $workingaddr $nor_workingaddr $filesize; "                \
 610         "protect on $nor_workingaddr +$filesize\0 "                     \
 611 "hwconfig=usb1:dr_mode=host,phy_type=ulpi\0 "                           \
 612 "kerneladdr=0x01100000\0"                                               \
 613 "kernelfile=uImage\0"                                                   \
 614 "loadaddr=0x01000000\0"                                                 \
 615 "mbr=uCP1020d.mbr\0"                                                    \
 616 "mbr_offset=0x00000000\0"                                               \
 617 "mmbr=uCP1020Quiet.mbr\0"                                               \
 618 "mmcpart=0:2\0"                                                         \
 619 "mmc__mbrd=fatload mmc $mmcpart $loadaddr $mbr; "                       \
 620         "mmc erase 1 1; "                                               \
 621         "mmc write $loadaddr 1 1\0"                                     \
 622 "mmc__uboot=fatload mmc $mmcpart $loadaddr $ubootfile; "                \
 623         "mmc erase 0x40 0x400; "                                        \
 624         "mmc write $loadaddr 0x40 0x400\0"                              \
 625 "netdev=eth0\0"                                                         \
 626 "nor_recoveryaddr=0xEC0A0000\0"                                         \
 627 "nor_ubootaddr=0xEFF80000\0"                                            \
 628 "nor_workingaddr=0xECFA0000\0"                                          \
 629 "norbootrecovery=setenv bootargs $recoverybootargs"                     \
 630         " console=$consoledev,$baudrate $othbootargs; "                 \
 631         "run norloadrecovery; "                                         \
 632         "bootm $kerneladdr - $dtbaddr\0"                                \
 633 "norbootworking=setenv bootargs $workingbootargs"                       \
 634         " console=$consoledev,$baudrate $othbootargs; "                 \
 635         "run norloadworking; "                                          \
 636         "bootm $kerneladdr - $dtbaddr\0"                                \
 637 "norloadrecovery=mw.l $kerneladdr 0x0 0x00a00000; "                     \
 638         "setenv cramfsaddr $nor_recoveryaddr; "                         \
 639         "cramfsload $dtbaddr $dtbfile; "                                \
 640         "cramfsload $kerneladdr $kernelfile\0"                          \
 641 "norloadworking=mw.l $kerneladdr 0x0 0x00a00000; "                      \
 642         "setenv cramfsaddr $nor_workingaddr; "                          \
 643         "cramfsload $dtbaddr $dtbfile; "                                \
 644         "cramfsload $kerneladdr $kernelfile\0"                          \
 645 "prog_spi_mbr=run spi__mbr\0"                                           \
 646 "prog_spi_mbrboot=run spi__mbr; run spi__boot1; run spi__boot2\0"       \
 647 "prog_spi_mbrbootcramfs=run spi__mbr; run spi__boot1; run spi__boot2; " \
 648         "run spi__cramfs\0"                                             \
 649 "ramboot=setenv bootargs root=/dev/ram ramdisk_size=$ramdisk_size ro"   \
 650         " console=$consoledev,$baudrate $othbootargs; "                 \
 651         "tftp $rootfsaddr $rootfsfile; "                                \
 652         "tftp $loadaddr $kernelfile; "                                  \
 653         "tftp $dtbaddr $dtbfile; "                                      \
 654         "bootm $loadaddr $rootfsaddr $dtbaddr\0"                        \
 655 "ramdisk_size=120000\0"                                                 \
 656 "ramdiskfile=rootfs.ext2.gz.uboot\0"                                    \
 657 "recoveryaddr=0x02F00000\0"                                             \
 658 "recoverybootargs=root=/dev/mtdblock0 rootfstype=cramfs ro\0"           \
 659 "releasefpga=mw.l 0xffe0f000 0x00400000; mw.l 0xffe0f004 0x00000000; "  \
 660         "mw.l 0xffe0f008 0x00400000\0"                                  \
 661 "rootfsaddr=0x02F00000\0"                                               \
 662 "rootfsfile=rootfs.ext2.gz.uboot\0"                                     \
 663 "rootpath=/opt/nfsroot\0"                                               \
 664 "spi__boot1=fatload mmc $mmcpart $loadaddr u-boot.bin; "                \
 665         "protect off 0xeC000000 +$filesize; "                           \
 666         "erase 0xEC000000 +$filesize; "                                 \
 667         "cp.b $loadaddr 0xEC000000 $filesize; "                         \
 668         "cmp.b $loadaddr 0xEC000000 $filesize; "                        \
 669         "protect on 0xeC000000 +$filesize\0"                            \
 670 "spi__boot2=fatload mmc $mmcpart $loadaddr u-boot.bin; "                \
 671         "protect off 0xeFF80000 +$filesize; "                           \
 672         "erase 0xEFF80000 +$filesize; "                                 \
 673         "cp.b $loadaddr 0xEFF80000 $filesize; "                         \
 674         "cmp.b $loadaddr 0xEFF80000 $filesize; "                        \
 675         "protect on 0xeFF80000 +$filesize\0"                            \
 676 "spi__bootd=fatload mmc $mmcpart $loadaddr $ubootd; "                   \
 677         "sf probe 0; sf erase 0x8000 +$filesize; "                      \
 678         "sf write $loadaddr 0x8000 $filesize\0"                         \
 679 "spi__cramfs=fatload mmc $mmcpart $loadaddr image.cramfs; "             \
 680         "protect off 0xec0a0000 +$filesize; "                           \
 681         "erase 0xeC0A0000 +$filesize; "                                 \
 682         "cp.b $loadaddr 0xeC0A0000 $filesize; "                         \
 683         "protect on 0xec0a0000 +$filesize\0"                            \
 684 "spi__mbr=fatload mmc $mmcpart $loadaddr $mmbr; "                       \
 685         "sf probe 1; sf erase 0 +$filesize; "                           \
 686         "sf write $loadaddr 0 $filesize\0"                              \
 687 "spi__mbrd=fatload mmc $mmcpart $loadaddr $mbr; "                       \
 688         "sf probe 0; sf erase 0 +$filesize; "                           \
 689         "sf write $loadaddr 0 $filesize\0"                              \
 690 "tftpflash=tftpboot $loadaddr $uboot; "                                 \
 691         "protect off " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
 692         "erase " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; "  \
 693         "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize; " \
 694         "protect on " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
 695         "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize\0"\
 696 "uboot= " __stringify(CONFIG_UBOOTPATH) "\0"                            \
 697 "ubootaddr=0x01000000\0"                                                \
 698 "ubootfile=u-boot.bin\0"                                                \
 699 "ubootd=u-boot4dongle.bin\0"                                            \
 700 "upgrade=run flashworking\0"                                            \
 701 "usb_phy_type=ulpi\0 "                                                  \
 702 "workingaddr=0x02F00000\0"                                              \
 703 "workingbootargs=root=/dev/mtdblock1 rootfstype=cramfs ro\0"
 704
 705 #else
 706
 707 #if defined(CONFIG_UCP1020T1)
 708
 709 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
 710 "bootcmd=run releasefpga; run norbootworking || run norbootrecovery\0"  \
 711 "bootfile=uImage\0"                                                     \
 712 "consoledev=ttyS0\0"                                                    \
 713 "cramfsfile=image.cramfs\0"                                             \
 714 "dtbaddr=0x00c00000\0"                                                  \
 715 "dtbfile=image.dtb\0"                                                   \
 716 "ethaddr=" __stringify(CONFIG_ETHADDR) "\0"                             \
 717 "eth1addr=" __stringify(CONFIG_ETH1ADDR) "\0"                           \
 718 "eth2addr=" __stringify(CONFIG_ETH2ADDR) "\0"                           \
 719 "fileaddr=0x01000000\0"                                                 \
 720 "filesize=0x00080000\0"                                                 \
 721 "flashmbr=sf probe 0; "                                                 \
 722         "tftp $loadaddr $mbr; "                                         \
 723         "sf erase $mbr_offset +$filesize; "                             \
 724         "sf write $loadaddr $mbr_offset $filesize\0"                    \
 725 "flashrecovery=tftp $recoveryaddr $cramfsfile; "                        \
 726         "protect off $nor_recoveryaddr +$filesize; "                    \
 727         "erase $nor_recoveryaddr +$filesize; "                          \
 728         "cp.b $recoveryaddr $nor_recoveryaddr $filesize; "              \
 729         "protect on $nor_recoveryaddr +$filesize\0 "                    \
 730 "flashuboot=tftp $ubootaddr $ubootfile; "                               \
 731         "protect off $nor_ubootaddr +$filesize; "                       \
 732         "erase $nor_ubootaddr +$filesize; "                             \
 733         "cp.b $ubootaddr $nor_ubootaddr $filesize; "                    \
 734         "protect on $nor_ubootaddr +$filesize\0 "                       \
 735 "flashworking=tftp $workingaddr $cramfsfile; "                          \
 736         "protect off $nor_workingaddr +$filesize; "                     \
 737         "erase $nor_workingaddr +$filesize; "                           \
 738         "cp.b $workingaddr $nor_workingaddr $filesize; "                \
 739         "protect on $nor_workingaddr +$filesize\0 "                     \
 740 "hwconfig=usb1:dr_mode=host,phy_type=ulpi\0 "                           \
 741 "kerneladdr=0x01100000\0"                                               \
 742 "kernelfile=uImage\0"                                                   \
 743 "loadaddr=0x01000000\0"                                                 \
 744 "mbr=uCP1020.mbr\0"                                                     \
 745 "mbr_offset=0x00000000\0"                                               \
 746 "netdev=eth0\0"                                                         \
 747 "nor_recoveryaddr=0xEC0A0000\0"                                         \
 748 "nor_ubootaddr=0xEFF80000\0"                                            \
 749 "nor_workingaddr=0xECFA0000\0"                                          \
 750 "norbootrecovery=setenv bootargs $recoverybootargs"                     \
 751         " console=$consoledev,$baudrate $othbootargs; "                 \
 752         "run norloadrecovery; "                                         \
 753         "bootm $kerneladdr - $dtbaddr\0"                                \
 754 "norbootworking=setenv bootargs $workingbootargs"                       \
 755         " console=$consoledev,$baudrate $othbootargs; "                 \
 756         "run norloadworking; "                                          \
 757         "bootm $kerneladdr - $dtbaddr\0"                                \
 758 "norloadrecovery=mw.l $kerneladdr 0x0 0x00a00000; "                     \
 759         "setenv cramfsaddr $nor_recoveryaddr; "                         \
 760         "cramfsload $dtbaddr $dtbfile; "                                \
 761         "cramfsload $kerneladdr $kernelfile\0"                          \
 762 "norloadworking=mw.l $kerneladdr 0x0 0x00a00000; "                      \
 763         "setenv cramfsaddr $nor_workingaddr; "                          \
 764         "cramfsload $dtbaddr $dtbfile; "                                \
 765         "cramfsload $kerneladdr $kernelfile\0"                          \
 766 "othbootargs=quiet\0"                                                   \
 767 "ramboot=setenv bootargs root=/dev/ram ramdisk_size=$ramdisk_size ro"   \
 768         " console=$consoledev,$baudrate $othbootargs; "                 \
 769         "tftp $rootfsaddr $rootfsfile; "                                \
 770         "tftp $loadaddr $kernelfile; "                                  \
 771         "tftp $dtbaddr $dtbfile; "                                      \
 772         "bootm $loadaddr $rootfsaddr $dtbaddr\0"                        \
 773 "ramdisk_size=120000\0"                                                 \
 774 "ramdiskfile=rootfs.ext2.gz.uboot\0"                                    \
 775 "recoveryaddr=0x02F00000\0"                                             \
 776 "recoverybootargs=root=/dev/mtdblock0 rootfstype=cramfs ro\0"           \
 777 "releasefpga=mw.l 0xffe0f000 0x00400000; mw.l 0xffe0f004 0x00000000; "  \
 778         "mw.l 0xffe0f008 0x00400000\0"                                  \
 779 "rootfsaddr=0x02F00000\0"                                               \
 780 "rootfsfile=rootfs.ext2.gz.uboot\0"                                     \
 781 "rootpath=/opt/nfsroot\0"                                               \
 782 "silent=1\0"                                                            \
 783 "tftpflash=tftpboot $loadaddr $uboot; "                                 \
 784         "protect off " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
 785         "erase " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; "  \
 786         "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize; " \
 787         "protect on " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
 788         "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize\0"\
 789 "uboot= " __stringify(CONFIG_UBOOTPATH) "\0"                            \
 790 "ubootaddr=0x01000000\0"                                                \
 791 "ubootfile=u-boot.bin\0"                                                \
 792 "upgrade=run flashworking\0"                                            \
 793 "workingaddr=0x02F00000\0"                                              \
 794 "workingbootargs=root=/dev/mtdblock1 rootfstype=cramfs ro\0"
 795
 796 #else /* For Arcturus Modules */
 797
 798 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
 799 "bootcmd=run norkernel\0"                                               \
 800 "bootfile=uImage\0"                                                     \
 801 "consoledev=ttyS0\0"                                                    \
 802 "dtbaddr=0x00c00000\0"                                                  \
 803 "dtbfile=image.dtb\0"                                                   \
 804 "ethaddr=" __stringify(CONFIG_ETHADDR) "\0"                             \
 805 "eth1addr=" __stringify(CONFIG_ETH1ADDR) "\0"                           \
 806 "eth2addr=" __stringify(CONFIG_ETH2ADDR) "\0"                           \
 807 "fileaddr=0x01000000\0"                                                 \
 808 "filesize=0x00080000\0"                                                 \
 809 "flashmbr=sf probe 0; "                                                 \
 810         "tftp $loadaddr $mbr; "                                         \
 811         "sf erase $mbr_offset +$filesize; "                             \
 812         "sf write $loadaddr $mbr_offset $filesize\0"                    \
 813 "flashuboot=tftp $loadaddr $ubootfile; "                                \
 814         "protect off $nor_ubootaddr0 +$filesize; "                      \
 815         "erase $nor_ubootaddr0 +$filesize; "                            \
 816         "cp.b $loadaddr $nor_ubootaddr0 $filesize; "                    \
 817         "protect on $nor_ubootaddr0 +$filesize; "                       \
 818         "protect off $nor_ubootaddr1 +$filesize; "                      \
 819         "erase $nor_ubootaddr1 +$filesize; "                            \
 820         "cp.b $loadaddr $nor_ubootaddr1 $filesize; "                    \
 821         "protect on $nor_ubootaddr1 +$filesize\0 "                      \
 822 "format0=protect off $part0base +$part0size; "                          \
 823         "erase $part0base +$part0size\0"                                \
 824 "format1=protect off $part1base +$part1size; "                          \
 825         "erase $part1base +$part1size\0"                                \
 826 "format2=protect off $part2base +$part2size; "                          \
 827         "erase $part2base +$part2size\0"                                \
 828 "format3=protect off $part3base +$part3size; "                          \
 829         "erase $part3base +$part3size\0"                                \
 830 "hwconfig=usb1:dr_mode=host,phy_type=ulpi\0 "                           \
 831 "kerneladdr=0x01100000\0"                                               \
 832 "kernelargs=root=/dev/mtdblock1 rootfstype=cramfs ro\0"                 \
 833 "kernelfile=uImage\0"                                                   \
 834 "loadaddr=0x01000000\0"                                                 \
 835 "mbr=uCP1020.mbr\0"                                                     \
 836 "mbr_offset=0x00000000\0"                                               \
 837 "netdev=eth0\0"                                                         \
 838 "nor_ubootaddr0=0xEC000000\0"                                           \
 839 "nor_ubootaddr1=0xEFF80000\0"                                           \
 840 "norkernel=setenv bootargs $kernelargs console=$consoledev,$baudrate; " \
 841         "run norkernelload; "                                           \
 842         "bootm $kerneladdr - $dtbaddr\0"                                \
 843 "norkernelload=mw.l $kerneladdr 0x0 0x00a00000; "                       \
 844         "setenv cramfsaddr $part0base; "                                \
 845         "cramfsload $dtbaddr $dtbfile; "                                \
 846         "cramfsload $kerneladdr $kernelfile\0"                          \
 847 "part0base=0xEC100000\0"                                                \
 848 "part0size=0x00700000\0"                                                \
 849 "part1base=0xEC800000\0"                                                \
 850 "part1size=0x02000000\0"                                                \
 851 "part2base=0xEE800000\0"                                                \
 852 "part2size=0x00800000\0"                                                \
 853 "part3base=0xEF000000\0"                                                \
 854 "part3size=0x00F80000\0"                                                \
 855 "partENVbase=0xEC080000\0"                                              \
 856 "partENVsize=0x00080000\0"                                              \
 857 "program0=tftp part0-000000.bin; "                                      \
 858         "protect off $part0base +$filesize; "                           \
 859         "erase $part0base +$filesize; "                                 \
 860         "cp.b $loadaddr $part0base $filesize; "                         \
 861         "echo Verifying...; "                                           \
 862         "cmp.b $loadaddr $part0base $filesize\0"                        \
 863 "program1=tftp part1-000000.bin; "                                      \
 864         "protect off $part1base +$filesize; "                           \
 865         "erase $part1base +$filesize; "                                 \
 866         "cp.b $loadaddr $part1base $filesize; "                         \
 867         "echo Verifying...; "                                           \
 868         "cmp.b $loadaddr $part1base $filesize\0"                        \
 869 "program2=tftp part2-000000.bin; "                                      \
 870         "protect off $part2base +$filesize; "                           \
 871         "erase $part2base +$filesize; "                                 \
 872         "cp.b $loadaddr $part2base $filesize; "                         \
 873         "echo Verifying...; "                                           \
 874         "cmp.b $loadaddr $part2base $filesize\0"                        \
 875 "ramboot=setenv bootargs root=/dev/ram ramdisk_size=$ramdisk_size ro"   \
 876         "  console=$consoledev,$baudrate $othbootargs; "                \
 877         "tftp $rootfsaddr $rootfsfile; "                                \
 878         "tftp $loadaddr $kernelfile; "                                  \
 879         "tftp $dtbaddr $dtbfile; "                                      \
 880         "bootm $loadaddr $rootfsaddr $dtbaddr\0"                        \
 881 "ramdisk_size=120000\0"                                                 \
 882 "ramdiskfile=rootfs.ext2.gz.uboot\0"                                    \
 883 "releasefpga=mw.l 0xffe0f000 0x00400000; mw.l 0xffe0f004 0x00000000; "  \
 884         "mw.l 0xffe0f008 0x00400000\0"                                  \
 885 "rootfsaddr=0x02F00000\0"                                               \
 886 "rootfsfile=rootfs.ext2.gz.uboot\0"                                     \
 887 "rootpath=/opt/nfsroot\0"                                               \
 888 "spi__mbr=fatload mmc $mmcpart $loadaddr $mmbr; "                       \
 889         "sf probe 0; sf erase 0 +$filesize; "                           \
 890         "sf write $loadaddr 0 $filesize\0"                              \
 891 "spi__boot=fatload mmc $mmcpart $loadaddr u-boot.bin; "                 \
 892         "protect off 0xeC000000 +$filesize; "                           \
 893         "erase 0xEC000000 +$filesize; "                                 \
 894         "cp.b $loadaddr 0xEC000000 $filesize; "                         \
 895         "cmp.b $loadaddr 0xEC000000 $filesize; "                        \
 896         "protect on 0xeC000000 +$filesize\0"                            \
 897 "tftpflash=tftpboot $loadaddr $uboot; "                                 \
 898         "protect off " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
 899         "erase " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; "  \
 900         "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize; " \
 901         "protect on " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
 902         "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize\0"\
 903 "uboot= " __stringify(CONFIG_UBOOTPATH) "\0"                            \
 904 "ubootfile=u-boot.bin\0"                                                \
 905 "upgrade=run flashuboot\0"                                              \
 906 "usb_phy_type=ulpi\0 "                                                  \
 907 "boot_nfs= "                                                            \
 908         "setenv bootargs root=/dev/nfs rw "                             \
 909         "nfsroot=$serverip:$rootpath "                                  \
 910         "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
 911         "console=$consoledev,$baudrate $othbootargs;"                   \
 912         "tftp $loadaddr $bootfile;"                                     \
 913         "tftp $fdtaddr $fdtfile;"                                       \
 914         "bootm $loadaddr - $fdtaddr\0"                                  \
 915 "boot_hd = "                                                            \
 916         "setenv bootargs root=/dev/$bdev rw rootdelay=30 "              \
 917         "console=$consoledev,$baudrate $othbootargs;"                   \
 918         "usb start;"                                                    \
 919         "ext2load usb 0:1 $loadaddr /boot/$bootfile;"                   \
 920         "ext2load usb 0:1 $fdtaddr /boot/$fdtfile;"                     \
 921         "bootm $loadaddr - $fdtaddr\0"                                  \
 922 "boot_usb_fat = "                                                       \
 923         "setenv bootargs root=/dev/ram rw "                             \
 924         "console=$consoledev,$baudrate $othbootargs "                   \
 925         "ramdisk_size=$ramdisk_size;"                                   \
 926         "usb start;"                                                    \
 927         "fatload usb 0:2 $loadaddr $bootfile;"                          \
 928         "fatload usb 0:2 $fdtaddr $fdtfile;"                            \
 929         "fatload usb 0:2 $ramdiskaddr $ramdiskfile;"                    \
 930         "bootm $loadaddr $ramdiskaddr $fdtaddr\0 "                      \
 931 "boot_usb_ext2 = "                                                      \
 932         "setenv bootargs root=/dev/ram rw "                             \
 933         "console=$consoledev,$baudrate $othbootargs "                   \
 934         "ramdisk_size=$ramdisk_size;"                                   \
 935         "usb start;"                                                    \
 936         "ext2load usb 0:4 $loadaddr $bootfile;"                         \
 937         "ext2load usb 0:4 $fdtaddr $fdtfile;"                           \
 938         "ext2load usb 0:4 $ramdiskaddr $ramdiskfile;"                   \
 939         "bootm $loadaddr $ramdiskaddr $fdtaddr\0 "                      \
 940 "boot_nor = "                                                           \
 941         "setenv bootargs root=/dev/$jffs2nor rw "                       \
 942         "console=$consoledev,$baudrate rootfstype=jffs2 $othbootargs;"  \
 943         "bootm $norbootaddr - $norfdtaddr\0 "                           \
 944 "boot_ram = "                                                           \
 945         "setenv bootargs root=/dev/ram rw "                             \
 946         "console=$consoledev,$baudrate $othbootargs "                   \
 947         "ramdisk_size=$ramdisk_size;"                                   \
 948         "tftp $ramdiskaddr $ramdiskfile;"                               \
 949         "tftp $loadaddr $bootfile;"                                     \
 950         "tftp $fdtaddr $fdtfile;"                                       \
 951         "bootm $loadaddr $ramdiskaddr $fdtaddr\0"
 952
 953 #endif
 954 #endif
 955
 956 #endif /* __CONFIG_H */