include/configs/UCP1020.h

   1 /*
   2  * Copyright 2013-2015 Arcturus Networks, Inc.
   3  *           http://www.arcturusnetworks.com/products/ucp1020/
   4  * based on include/configs/p1_p2_rdb_pc.h
   5  * original copyright follows:
   6  * Copyright 2009-2011 Freescale Semiconductor, Inc.
   7  *
   8  * SPDX-License-Identifier:     GPL-2.0+
   9  */
  10
  11 /*
  12  * QorIQ uCP1020-xx boards configuration file
  13  */
  14 #ifndef __CONFIG_H
  15 #define __CONFIG_H
  16
  17 #define CONFIG_PCIE1    /* PCIE controller 1 (slot 1) */
  18 #define CONFIG_PCIE2    /* PCIE controller 2 (slot 2) */
  19 #define CONFIG_FSL_PCI_INIT     /* Use common FSL init code */
  20 #define CONFIG_PCI_INDIRECT_BRIDGE      /* indirect PCI bridge support */
  21 #define CONFIG_FSL_PCIE_RESET   /* need PCIe reset errata */
  22 #define CONFIG_SYS_PCI_64BIT    /* enable 64-bit PCI resources */
  23
  24 #if defined(CONFIG_TARTGET_UCP1020T1)
  25
  26 #define CONFIG_UCP1020_REV_1_3
  27
  28 #define CONFIG_BOARDNAME "uCP1020-64EE512-0U1-XR-T1"
  29
  30 #define CONFIG_TSEC_ENET
  31 #define CONFIG_TSEC1
  32 #define CONFIG_TSEC3
  33 #define CONFIG_HAS_ETH0
  34 #define CONFIG_HAS_ETH1
  35 #define CONFIG_ETHADDR          00:19:D3:FF:FF:FF
  36 #define CONFIG_ETH1ADDR         00:19:D3:FF:FF:FE
  37 #define CONFIG_ETH2ADDR         00:19:D3:FF:FF:FD
  38 #define CONFIG_IPADDR           10.80.41.229
  39 #define CONFIG_SERVERIP         10.80.41.227
  40 #define CONFIG_NETMASK          255.255.252.0
  41 #define CONFIG_ETHPRIME         "eTSEC3"
  42
  43 #ifndef CONFIG_SPI_FLASH
  44 #endif
  45 #define CONFIG_SYS_REDUNDAND_ENVIRONMENT
  46
  47 #define CONFIG_SYS_L2_SIZE      (256 << 10)
  48
  49 #define CONFIG_LAST_STAGE_INIT
  50
  51 #endif
  52
  53 #if defined(CONFIG_TARGET_UCP1020)
  54
  55 #define CONFIG_UCP1020
  56 #define CONFIG_UCP1020_REV_1_3
  57
  58 #define CONFIG_BOARDNAME_LOCAL "uCP1020-64EEE512-OU1-XR"
  59
  60 #define CONFIG_TSEC_ENET
  61 #define CONFIG_TSEC1
  62 #define CONFIG_TSEC2
  63 #define CONFIG_TSEC3
  64 #define CONFIG_HAS_ETH0
  65 #define CONFIG_HAS_ETH1
  66 #define CONFIG_HAS_ETH2
  67 #define CONFIG_ETHADDR          00:06:3B:FF:FF:FF
  68 #define CONFIG_ETH1ADDR         00:06:3B:FF:FF:FE
  69 #define CONFIG_ETH2ADDR         00:06:3B:FF:FF:FD
  70 #define CONFIG_IPADDR           192.168.1.81
  71 #define CONFIG_IPADDR1          192.168.1.82
  72 #define CONFIG_IPADDR2          192.168.1.83
  73 #define CONFIG_SERVERIP         192.168.1.80
  74 #define CONFIG_GATEWAYIP        102.168.1.1
  75 #define CONFIG_NETMASK          255.255.255.0
  76 #define CONFIG_ETHPRIME         "eTSEC1"
  77
  78 #ifndef CONFIG_SPI_FLASH
  79 #endif
  80 #define CONFIG_SYS_REDUNDAND_ENVIRONMENT
  81
  82 #define CONFIG_SYS_L2_SIZE      (256 << 10)
  83
  84 #define CONFIG_LAST_STAGE_INIT
  85
  86 #endif
  87
  88 #ifdef CONFIG_SDCARD
  89 #define CONFIG_RAMBOOT_SDCARD
  90 #define CONFIG_SYS_RAMBOOT
  91 #define CONFIG_SYS_EXTRA_ENV_RELOC
  92 #define CONFIG_RESET_VECTOR_ADDRESS     0x1107fffc
  93 #endif
  94
  95 #ifdef CONFIG_SPIFLASH
  96 #define CONFIG_RAMBOOT_SPIFLASH
  97 #define CONFIG_SYS_RAMBOOT
  98 #define CONFIG_SYS_EXTRA_ENV_RELOC
  99 #define CONFIG_RESET_VECTOR_ADDRESS     0x1107fffc
 100 #endif
 101
 102 #define CONFIG_SYS_TEXT_BASE_NOR        0xeff80000
 103
 104 #ifndef CONFIG_RESET_VECTOR_ADDRESS
 105 #define CONFIG_RESET_VECTOR_ADDRESS     0xeffffffc
 106 #endif
 107
 108 #ifndef CONFIG_SYS_MONITOR_BASE
 109 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE    /* start of monitor */
 110 #endif
 111
 112 #define CONFIG_MP
 113
 114 #define CONFIG_ENV_OVERWRITE
 115
 116 #define CONFIG_SYS_SATA_MAX_DEVICE      2
 117 #define CONFIG_LBA48
 118
 119 #define CONFIG_SYS_CLK_FREQ     66666666
 120 #define CONFIG_DDR_CLK_FREQ     66666666
 121
 122 #define CONFIG_HWCONFIG
 123
 124 /*
 125  * These can be toggled for performance analysis, otherwise use default.
 126  */
 127 #define CONFIG_L2_CACHE
 128 #define CONFIG_BTB
 129
 130 #define CONFIG_ENABLE_36BIT_PHYS
 131
 132 #define CONFIG_SYS_MEMTEST_START        0x00200000      /* memtest works on */
 133 #define CONFIG_SYS_MEMTEST_END          0x1fffffff
 134
 135 #define CONFIG_SYS_CCSRBAR              0xffe00000
 136 #define CONFIG_SYS_CCSRBAR_PHYS_LOW     CONFIG_SYS_CCSRBAR
 137
 138 /* IN case of NAND bootloader relocate CCSRBAR in RAMboot code not in the 4k
 139        SPL code*/
 140 #ifdef CONFIG_SPL_BUILD
 141 #define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
 142 #endif
 143
 144 /* DDR Setup */
 145 #define CONFIG_DDR_ECC_ENABLE
 146 #ifndef CONFIG_DDR_ECC_ENABLE
 147 #define CONFIG_SYS_DDR_RAW_TIMING
 148 #define CONFIG_DDR_SPD
 149 #endif
 150 #define CONFIG_SYS_SPD_BUS_NUM 1
 151 #undef CONFIG_FSL_DDR_INTERACTIVE
 152
 153 #define CONFIG_SYS_SDRAM_SIZE_LAW       LAW_SIZE_512M
 154 #define CONFIG_CHIP_SELECTS_PER_CTRL    1
 155 #define CONFIG_SYS_SDRAM_SIZE           (1u << (CONFIG_SYS_SDRAM_SIZE_LAW - 19))
 156 #define CONFIG_SYS_DDR_SDRAM_BASE       0x00000000
 157 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE
 158
 159 #define CONFIG_DIMM_SLOTS_PER_CTLR      1
 160
 161 /* Default settings for DDR3 */
 162 #define CONFIG_SYS_DDR_CS0_BNDS         0x0000003f
 163 #define CONFIG_SYS_DDR_CS0_CONFIG       0x80014302
 164 #define CONFIG_SYS_DDR_CS0_CONFIG_2     0x00000000
 165 #define CONFIG_SYS_DDR_CS1_BNDS         0x0040007f
 166 #define CONFIG_SYS_DDR_CS1_CONFIG       0x80014302
 167 #define CONFIG_SYS_DDR_CS1_CONFIG_2     0x00000000
 168
 169 #define CONFIG_SYS_DDR_DATA_INIT        0xdeadbeef
 170 #define CONFIG_SYS_DDR_INIT_ADDR        0x00000000
 171 #define CONFIG_SYS_DDR_INIT_EXT_ADDR    0x00000000
 172 #define CONFIG_SYS_DDR_MODE_CONTROL     0x00000000
 173
 174 #define CONFIG_SYS_DDR_ZQ_CONTROL       0x89080600
 175 #define CONFIG_SYS_DDR_WRLVL_CONTROL    0x8655A608
 176 #define CONFIG_SYS_DDR_SR_CNTR          0x00000000
 177 #define CONFIG_SYS_DDR_RCW_1            0x00000000
 178 #define CONFIG_SYS_DDR_RCW_2            0x00000000
 179 #ifdef CONFIG_DDR_ECC_ENABLE
 180 #define CONFIG_SYS_DDR_CONTROL          0xE70C0000      /* Type = DDR3 & ECC */
 181 #else
 182 #define CONFIG_SYS_DDR_CONTROL          0xC70C0000      /* Type = DDR3 */
 183 #endif
 184 #define CONFIG_SYS_DDR_CONTROL_2        0x04401050
 185 #define CONFIG_SYS_DDR_TIMING_4         0x00220001
 186 #define CONFIG_SYS_DDR_TIMING_5         0x03402400
 187
 188 #define CONFIG_SYS_DDR_TIMING_3         0x00020000
 189 #define CONFIG_SYS_DDR_TIMING_0         0x00330004
 190 #define CONFIG_SYS_DDR_TIMING_1         0x6f6B4846
 191 #define CONFIG_SYS_DDR_TIMING_2         0x0FA8C8CF
 192 #define CONFIG_SYS_DDR_CLK_CTRL         0x03000000
 193 #define CONFIG_SYS_DDR_MODE_1           0x40461520
 194 #define CONFIG_SYS_DDR_MODE_2           0x8000c000
 195 #define CONFIG_SYS_DDR_INTERVAL         0x0C300000
 196
 197 #undef CONFIG_CLOCKS_IN_MHZ
 198
 199 /*
 200  * Memory map
 201  *
 202  * 0x0000_0000 0x7fff_ffff      DDR             Up to 2GB cacheable
 203  * 0x8000_0000 0xdfff_ffff      PCI Express Mem 1G non-cacheable(PCIe * 2)
 204  * 0xec00_0000 0xefff_ffff      NOR flash       Up to 64M non-cacheable CS0/1
 205  * 0xf8f8_0000 0xf8ff_ffff      L2 SRAM         Up to 256K cacheable
 206  *   (early boot only)
 207  * 0xffc0_0000 0xffc3_ffff      PCI IO range    256k non-cacheable
 208  * 0xffd0_0000 0xffd0_3fff      L1 for stack    16K cacheable
 209  * 0xffe0_0000 0xffef_ffff      CCSR            1M non-cacheable
 210  */
 211
 212 /*
 213  * Local Bus Definitions
 214  */
 215 #define CONFIG_SYS_MAX_FLASH_SECT       512     /* 64M */
 216 #define CONFIG_SYS_FLASH_BASE           0xec000000
 217
 218 #define CONFIG_SYS_FLASH_BASE_PHYS      CONFIG_SYS_FLASH_BASE
 219
 220 #define CONFIG_FLASH_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \
 221         | BR_PS_16 | BR_V)
 222
 223 #define CONFIG_FLASH_OR_PRELIM          0xfc000ff7
 224
 225 #define CONFIG_SYS_FLASH_BANKS_LIST     {CONFIG_SYS_FLASH_BASE_PHYS}
 226 #define CONFIG_SYS_FLASH_QUIET_TEST
 227 #define CONFIG_FLASH_SHOW_PROGRESS      45      /* count down from 45/5: 9..1 */
 228
 229 #define CONFIG_SYS_MAX_FLASH_BANKS      1       /* number of banks */
 230
 231 #undef CONFIG_SYS_FLASH_CHECKSUM
 232 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000   /* Flash Erase Timeout (ms) */
 233 #define CONFIG_SYS_FLASH_WRITE_TOUT     500     /* Flash Write Timeout (ms) */
 234
 235 #define CONFIG_FLASH_CFI_DRIVER
 236 #define CONFIG_SYS_FLASH_CFI
 237 #define CONFIG_SYS_FLASH_EMPTY_INFO
 238 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
 239
 240 #define CONFIG_BOARD_EARLY_INIT_R       /* call board_early_init_r function */
 241
 242 #define CONFIG_SYS_INIT_RAM_LOCK
 243 #define CONFIG_SYS_INIT_RAM_ADDR        0xffd00000 /* stack in RAM */
 244 /* Initial L1 address */
 245 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS   CONFIG_SYS_INIT_RAM_ADDR
 246 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0
 247 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS
 248 /* Size of used area in RAM */
 249 #define CONFIG_SYS_INIT_RAM_SIZE        0x00004000
 250
 251 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - \
 252                                         GENERATED_GBL_DATA_SIZE)
 253 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 254
 255 #define CONFIG_SYS_MONITOR_LEN  (256 * 1024)/* Reserve 256 kB for Mon */
 256 #define CONFIG_SYS_MALLOC_LEN   (1024 * 1024)/* Reserved for malloc */
 257
 258 #define CONFIG_SYS_PMC_BASE     0xff980000
 259 #define CONFIG_SYS_PMC_BASE_PHYS        CONFIG_SYS_PMC_BASE
 260 #define CONFIG_PMC_BR_PRELIM    (BR_PHYS_ADDR(CONFIG_SYS_PMC_BASE_PHYS) | \
 261                                         BR_PS_8 | BR_V)
 262 #define CONFIG_PMC_OR_PRELIM    (OR_AM_64KB | OR_GPCM_CSNT | OR_GPCM_XACS | \
 263                                  OR_GPCM_SCY | OR_GPCM_TRLX | OR_GPCM_EHTR | \
 264                                  OR_GPCM_EAD)
 265
 266 #define CONFIG_SYS_BR0_PRELIM   CONFIG_FLASH_BR_PRELIM  /* NOR Base Address */
 267 #define CONFIG_SYS_OR0_PRELIM   CONFIG_FLASH_OR_PRELIM  /* NOR Options */
 268 #ifdef CONFIG_NAND_FSL_ELBC
 269 #define CONFIG_SYS_BR1_PRELIM   CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Addr */
 270 #define CONFIG_SYS_OR1_PRELIM   CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */
 271 #endif
 272
 273 /* Serial Port - controlled on board with jumper J8
 274  * open - index 2
 275  * shorted - index 1
 276  */
 277 #define CONFIG_CONS_INDEX               1
 278 #undef CONFIG_SERIAL_SOFTWARE_FIFO
 279 #define CONFIG_SYS_NS16550_SERIAL
 280 #define CONFIG_SYS_NS16550_REG_SIZE     1
 281 #define CONFIG_SYS_NS16550_CLK          get_bus_freq(0)
 282 #if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_INIT_MINIMAL)
 283 #define CONFIG_NS16550_MIN_FUNCTIONS
 284 #endif
 285
 286 #define CONFIG_SYS_BAUDRATE_TABLE       \
 287         {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
 288
 289 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR + 0x4500)
 290 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR + 0x4600)
 291
 292 /* I2C */
 293 #define CONFIG_SYS_I2C
 294 #define CONFIG_SYS_I2C_FSL
 295 #define CONFIG_SYS_FSL_I2C_SPEED        400000
 296 #define CONFIG_SYS_FSL_I2C_SLAVE        0x7F
 297 #define CONFIG_SYS_FSL_I2C_OFFSET       0x3000
 298 #define CONFIG_SYS_FSL_I2C2_SPEED       400000
 299 #define CONFIG_SYS_FSL_I2C2_SLAVE       0x7F
 300 #define CONFIG_SYS_FSL_I2C2_OFFSET      0x3100
 301 #define CONFIG_SYS_I2C_NOPROBES         { {0, 0x29} }
 302 #define CONFIG_SYS_SPD_BUS_NUM          1 /* For rom_loc and flash bank */
 303
 304 #define CONFIG_RTC_DS1337
 305 #define CONFIG_RTC_DS1337_NOOSC
 306 #define CONFIG_SYS_I2C_RTC_ADDR         0x68
 307 #define CONFIG_SYS_I2C_PCA9557_ADDR     0x18
 308 #define CONFIG_SYS_I2C_NCT72_ADDR       0x4C
 309 #define CONFIG_SYS_I2C_IDT6V49205B      0x69
 310
 311 /*
 312  * eSPI - Enhanced SPI
 313  */
 314 #define CONFIG_HARD_SPI
 315
 316 #define CONFIG_SF_DEFAULT_SPEED         10000000
 317 #define CONFIG_SF_DEFAULT_MODE          SPI_MODE_0
 318
 319 #if defined(CONFIG_PCI)
 320 /*
 321  * General PCI
 322  * Memory space is mapped 1-1, but I/O space must start from 0.
 323  */
 324
 325 /* controller 2, direct to uli, tgtid 2, Base address 9000 */
 326 #define CONFIG_SYS_PCIE2_NAME           "PCIe SLOT CON9"
 327 #define CONFIG_SYS_PCIE2_MEM_VIRT       0xa0000000
 328 #define CONFIG_SYS_PCIE2_MEM_BUS        0xa0000000
 329 #define CONFIG_SYS_PCIE2_MEM_PHYS       0xa0000000
 330 #define CONFIG_SYS_PCIE2_MEM_SIZE       0x20000000      /* 512M */
 331 #define CONFIG_SYS_PCIE2_IO_VIRT        0xffc10000
 332 #define CONFIG_SYS_PCIE2_IO_BUS         0x00000000
 333 #define CONFIG_SYS_PCIE2_IO_PHYS        0xffc10000
 334 #define CONFIG_SYS_PCIE2_IO_SIZE        0x00010000      /* 64k */
 335
 336 /* controller 1, Slot 2, tgtid 1, Base address a000 */
 337 #define CONFIG_SYS_PCIE1_NAME           "PCIe SLOT CON10"
 338 #define CONFIG_SYS_PCIE1_MEM_VIRT       0x80000000
 339 #define CONFIG_SYS_PCIE1_MEM_BUS        0x80000000
 340 #define CONFIG_SYS_PCIE1_MEM_PHYS       0x80000000
 341 #define CONFIG_SYS_PCIE1_MEM_SIZE       0x20000000      /* 512M */
 342 #define CONFIG_SYS_PCIE1_IO_VIRT        0xffc00000
 343 #define CONFIG_SYS_PCIE1_IO_BUS         0x00000000
 344 #define CONFIG_SYS_PCIE1_IO_PHYS        0xffc00000
 345 #define CONFIG_SYS_PCIE1_IO_SIZE        0x00010000      /* 64k */
 346
 347 #define CONFIG_PCI_SCAN_SHOW    /* show pci devices on startup */
 348 #endif /* CONFIG_PCI */
 349
 350 /*
 351  * Environment
 352  */
 353 #ifdef CONFIG_ENV_FIT_UCBOOT
 354
 355 #define CONFIG_ENV_ADDR         (CONFIG_SYS_FLASH_BASE + 0x20000)
 356 #define CONFIG_ENV_SIZE         0x20000
 357 #define CONFIG_ENV_SECT_SIZE    0x20000 /* 128K (one sector) */
 358
 359 #else
 360
 361 #define CONFIG_ENV_SPI_BUS      0
 362 #define CONFIG_ENV_SPI_CS       0
 363 #define CONFIG_ENV_SPI_MAX_HZ   10000000
 364 #define CONFIG_ENV_SPI_MODE     0
 365
 366 #ifdef CONFIG_RAMBOOT_SPIFLASH
 367
 368 #define CONFIG_ENV_SIZE         0x3000          /* 12KB */
 369 #define CONFIG_ENV_OFFSET       0x2000          /* 8KB */
 370 #define CONFIG_ENV_SECT_SIZE    0x1000
 371
 372 #if defined(CONFIG_SYS_REDUNDAND_ENVIRONMENT)
 373 /* Address and size of Redundant Environment Sector     */
 374 #define CONFIG_ENV_OFFSET_REDUND        (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
 375 #define CONFIG_ENV_SIZE_REDUND          CONFIG_ENV_SIZE
 376 #endif
 377
 378 #elif defined(CONFIG_RAMBOOT_SDCARD)
 379 #define CONFIG_FSL_FIXED_MMC_LOCATION
 380 #define CONFIG_ENV_SIZE         0x2000
 381 #define CONFIG_SYS_MMC_ENV_DEV  0
 382
 383 #elif defined(CONFIG_SYS_RAMBOOT)
 384 #define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE - 0x1000)
 385 #define CONFIG_ENV_SIZE         0x2000
 386
 387 #else
 388 #define CONFIG_ENV_BASE         (CONFIG_SYS_FLASH_BASE)
 389 #define CONFIG_ENV_SECT_SIZE    0x20000 /* 128K (one sector) */
 390 #define CONFIG_ENV_SIZE         CONFIG_ENV_SECT_SIZE
 391 #define CONFIG_ENV_ADDR         (CONFIG_ENV_BASE + 0xC0000)
 392 #if defined(CONFIG_SYS_REDUNDAND_ENVIRONMENT)
 393 /* Address and size of Redundant Environment Sector     */
 394 #define CONFIG_ENV_ADDR_REDUND  (CONFIG_ENV_ADDR + CONFIG_ENV_SIZE)
 395 #define CONFIG_ENV_SIZE_REDUND  CONFIG_ENV_SIZE
 396 #endif
 397
 398 #endif
 399
 400 #endif  /* CONFIG_ENV_FIT_UCBOOT */
 401
 402 #define CONFIG_LOADS_ECHO               /* echo on for serial download */
 403 #define CONFIG_SYS_LOADS_BAUD_CHANGE    /* allow baudrate change */
 404
 405 /*
 406  * USB
 407  */
 408 #define CONFIG_HAS_FSL_DR_USB
 409
 410 #if defined(CONFIG_HAS_FSL_DR_USB)
 411 #define CONFIG_USB_MAX_CONTROLLER_COUNT 1
 412
 413 #ifdef CONFIG_USB_EHCI_HCD
 414 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 415 #define CONFIG_USB_EHCI_FSL
 416 #endif
 417 #endif
 418
 419 #undef CONFIG_WATCHDOG                  /* watchdog disabled */
 420
 421 #ifdef CONFIG_MMC
 422 #define CONFIG_FSL_ESDHC
 423 #define CONFIG_SYS_FSL_ESDHC_ADDR       CONFIG_SYS_MPC85xx_ESDHC_ADDR
 424 #define CONFIG_MMC_SPI
 425 #endif
 426
 427 /* Misc Extra Settings */
 428 #undef CONFIG_WATCHDOG  /* watchdog disabled */
 429
 430 /*
 431  * Miscellaneous configurable options
 432  */
 433 #define CONFIG_SYS_LOAD_ADDR    0x2000000       /* default load address */
 434 #define CONFIG_SYS_HZ           1000    /* decrementer freq: 1ms tick */
 435
 436 /*
 437  * For booting Linux, the board info and command line data
 438  * have to be in the first 64 MB of memory, since this is
 439  * the maximum mapped by the Linux kernel during initialization.
 440  */
 441 #define CONFIG_SYS_BOOTMAPSZ    (64 << 20)      /* Initial Memory for Linux*/
 442 #define CONFIG_SYS_BOOTM_LEN    (64 << 20)      /* Increase max gunzip size */
 443
 444 #if defined(CONFIG_CMD_KGDB)
 445 #define CONFIG_KGDB_BAUDRATE    230400  /* speed to run kgdb serial port */
 446 #define CONFIG_KGDB_SER_INDEX   2       /* which serial port to use */
 447 #endif
 448
 449 /*
 450  * Environment Configuration
 451  */
 452
 453 #if defined(CONFIG_TSEC_ENET)
 454
 455 #if defined(CONFIG_UCP1020_REV_1_2) || defined(CONFIG_UCP1020_REV_1_3)
 456 #else
 457 #error "UCP1020 module revision is not defined !!!"
 458 #endif
 459
 460 #define CONFIG_BOOTP_SERVERIP
 461
 462 #define CONFIG_MII              /* MII PHY management */
 463 #define CONFIG_TSEC1_NAME       "eTSEC1"
 464 #define CONFIG_TSEC2_NAME       "eTSEC2"
 465 #define CONFIG_TSEC3_NAME       "eTSEC3"
 466
 467 #define TSEC1_PHY_ADDR  4
 468 #define TSEC2_PHY_ADDR  0
 469 #define TSEC2_PHY_ADDR_SGMII    0x00
 470 #define TSEC3_PHY_ADDR  6
 471
 472 #define TSEC1_FLAGS     (TSEC_GIGABIT | TSEC_REDUCED)
 473 #define TSEC2_FLAGS     (TSEC_GIGABIT | TSEC_REDUCED)
 474 #define TSEC3_FLAGS     (TSEC_GIGABIT | TSEC_REDUCED)
 475
 476 #define TSEC1_PHYIDX    0
 477 #define TSEC2_PHYIDX    0
 478 #define TSEC3_PHYIDX    0
 479
 480 #endif
 481
 482 #define CONFIG_HOSTNAME         UCP1020
 483 #define CONFIG_ROOTPATH         "/opt/nfsroot"
 484 #define CONFIG_BOOTFILE         "uImage"
 485 #define CONFIG_UBOOTPATH        u-boot.bin /* U-Boot image on TFTP server */
 486
 487 /* default location for tftp and bootm */
 488 #define CONFIG_LOADADDR         1000000
 489
 490 #if defined(CONFIG_DONGLE)
 491
 492 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
 493 "bootcmd=run prog_spi_mbrbootcramfs\0"                                  \
 494 "bootfile=uImage\0"                                                     \
 495 "consoledev=ttyS0\0"                                                    \
 496 "cramfsfile=image.cramfs\0"                                             \
 497 "dtbaddr=0x00c00000\0"                                                  \
 498 "dtbfile=image.dtb\0"                                                   \
 499 "ethaddr=" __stringify(CONFIG_ETHADDR) "\0"                             \
 500 "eth1addr=" __stringify(CONFIG_ETH1ADDR) "\0"                           \
 501 "eth2addr=" __stringify(CONFIG_ETH2ADDR) "\0"                           \
 502 "fileaddr=0x01000000\0"                                                 \
 503 "filesize=0x00080000\0"                                                 \
 504 "flashmbr=sf probe 0; "                                                 \
 505         "tftp $loadaddr $mbr; "                                         \
 506         "sf erase $mbr_offset +$filesize; "                             \
 507         "sf write $loadaddr $mbr_offset $filesize\0"                    \
 508 "flashrecovery=tftp $recoveryaddr $cramfsfile; "                        \
 509         "protect off $nor_recoveryaddr +$filesize; "                    \
 510         "erase $nor_recoveryaddr +$filesize; "                          \
 511         "cp.b $recoveryaddr $nor_recoveryaddr $filesize; "              \
 512         "protect on $nor_recoveryaddr +$filesize\0 "                    \
 513 "flashuboot=tftp $ubootaddr $ubootfile; "                               \
 514         "protect off $nor_ubootaddr +$filesize; "                       \
 515         "erase $nor_ubootaddr +$filesize; "                             \
 516         "cp.b $ubootaddr $nor_ubootaddr $filesize; "                    \
 517         "protect on $nor_ubootaddr +$filesize\0 "                       \
 518 "flashworking=tftp $workingaddr $cramfsfile; "                          \
 519         "protect off $nor_workingaddr +$filesize; "                     \
 520         "erase $nor_workingaddr +$filesize; "                           \
 521         "cp.b $workingaddr $nor_workingaddr $filesize; "                \
 522         "protect on $nor_workingaddr +$filesize\0 "                     \
 523 "hwconfig=usb1:dr_mode=host,phy_type=ulpi\0 "                           \
 524 "kerneladdr=0x01100000\0"                                               \
 525 "kernelfile=uImage\0"                                                   \
 526 "loadaddr=0x01000000\0"                                                 \
 527 "mbr=uCP1020d.mbr\0"                                                    \
 528 "mbr_offset=0x00000000\0"                                               \
 529 "mmbr=uCP1020Quiet.mbr\0"                                               \
 530 "mmcpart=0:2\0"                                                         \
 531 "mmc__mbrd=fatload mmc $mmcpart $loadaddr $mbr; "                       \
 532         "mmc erase 1 1; "                                               \
 533         "mmc write $loadaddr 1 1\0"                                     \
 534 "mmc__uboot=fatload mmc $mmcpart $loadaddr $ubootfile; "                \
 535         "mmc erase 0x40 0x400; "                                        \
 536         "mmc write $loadaddr 0x40 0x400\0"                              \
 537 "netdev=eth0\0"                                                         \
 538 "nor_recoveryaddr=0xEC0A0000\0"                                         \
 539 "nor_ubootaddr=0xEFF80000\0"                                            \
 540 "nor_workingaddr=0xECFA0000\0"                                          \
 541 "norbootrecovery=setenv bootargs $recoverybootargs"                     \
 542         " console=$consoledev,$baudrate $othbootargs; "                 \
 543         "run norloadrecovery; "                                         \
 544         "bootm $kerneladdr - $dtbaddr\0"                                \
 545 "norbootworking=setenv bootargs $workingbootargs"                       \
 546         " console=$consoledev,$baudrate $othbootargs; "                 \
 547         "run norloadworking; "                                          \
 548         "bootm $kerneladdr - $dtbaddr\0"                                \
 549 "norloadrecovery=mw.l $kerneladdr 0x0 0x00a00000; "                     \
 550         "setenv cramfsaddr $nor_recoveryaddr; "                         \
 551         "cramfsload $dtbaddr $dtbfile; "                                \
 552         "cramfsload $kerneladdr $kernelfile\0"                          \
 553 "norloadworking=mw.l $kerneladdr 0x0 0x00a00000; "                      \
 554         "setenv cramfsaddr $nor_workingaddr; "                          \
 555         "cramfsload $dtbaddr $dtbfile; "                                \
 556         "cramfsload $kerneladdr $kernelfile\0"                          \
 557 "prog_spi_mbr=run spi__mbr\0"                                           \
 558 "prog_spi_mbrboot=run spi__mbr; run spi__boot1; run spi__boot2\0"       \
 559 "prog_spi_mbrbootcramfs=run spi__mbr; run spi__boot1; run spi__boot2; " \
 560         "run spi__cramfs\0"                                             \
 561 "ramboot=setenv bootargs root=/dev/ram ramdisk_size=$ramdisk_size ro"   \
 562         " console=$consoledev,$baudrate $othbootargs; "                 \
 563         "tftp $rootfsaddr $rootfsfile; "                                \
 564         "tftp $loadaddr $kernelfile; "                                  \
 565         "tftp $dtbaddr $dtbfile; "                                      \
 566         "bootm $loadaddr $rootfsaddr $dtbaddr\0"                        \
 567 "ramdisk_size=120000\0"                                                 \
 568 "ramdiskfile=rootfs.ext2.gz.uboot\0"                                    \
 569 "recoveryaddr=0x02F00000\0"                                             \
 570 "recoverybootargs=root=/dev/mtdblock0 rootfstype=cramfs ro\0"           \
 571 "releasefpga=mw.l 0xffe0f000 0x00400000; mw.l 0xffe0f004 0x00000000; "  \
 572         "mw.l 0xffe0f008 0x00400000\0"                                  \
 573 "rootfsaddr=0x02F00000\0"                                               \
 574 "rootfsfile=rootfs.ext2.gz.uboot\0"                                     \
 575 "rootpath=/opt/nfsroot\0"                                               \
 576 "spi__boot1=fatload mmc $mmcpart $loadaddr u-boot.bin; "                \
 577         "protect off 0xeC000000 +$filesize; "                           \
 578         "erase 0xEC000000 +$filesize; "                                 \
 579         "cp.b $loadaddr 0xEC000000 $filesize; "                         \
 580         "cmp.b $loadaddr 0xEC000000 $filesize; "                        \
 581         "protect on 0xeC000000 +$filesize\0"                            \
 582 "spi__boot2=fatload mmc $mmcpart $loadaddr u-boot.bin; "                \
 583         "protect off 0xeFF80000 +$filesize; "                           \
 584         "erase 0xEFF80000 +$filesize; "                                 \
 585         "cp.b $loadaddr 0xEFF80000 $filesize; "                         \
 586         "cmp.b $loadaddr 0xEFF80000 $filesize; "                        \
 587         "protect on 0xeFF80000 +$filesize\0"                            \
 588 "spi__bootd=fatload mmc $mmcpart $loadaddr $ubootd; "                   \
 589         "sf probe 0; sf erase 0x8000 +$filesize; "                      \
 590         "sf write $loadaddr 0x8000 $filesize\0"                         \
 591 "spi__cramfs=fatload mmc $mmcpart $loadaddr image.cramfs; "             \
 592         "protect off 0xec0a0000 +$filesize; "                           \
 593         "erase 0xeC0A0000 +$filesize; "                                 \
 594         "cp.b $loadaddr 0xeC0A0000 $filesize; "                         \
 595         "protect on 0xec0a0000 +$filesize\0"                            \
 596 "spi__mbr=fatload mmc $mmcpart $loadaddr $mmbr; "                       \
 597         "sf probe 1; sf erase 0 +$filesize; "                           \
 598         "sf write $loadaddr 0 $filesize\0"                              \
 599 "spi__mbrd=fatload mmc $mmcpart $loadaddr $mbr; "                       \
 600         "sf probe 0; sf erase 0 +$filesize; "                           \
 601         "sf write $loadaddr 0 $filesize\0"                              \
 602 "tftpflash=tftpboot $loadaddr $uboot; "                                 \
 603         "protect off " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
 604         "erase " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; "  \
 605         "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize; " \
 606         "protect on " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
 607         "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize\0"\
 608 "uboot= " __stringify(CONFIG_UBOOTPATH) "\0"                            \
 609 "ubootaddr=0x01000000\0"                                                \
 610 "ubootfile=u-boot.bin\0"                                                \
 611 "ubootd=u-boot4dongle.bin\0"                                            \
 612 "upgrade=run flashworking\0"                                            \
 613 "usb_phy_type=ulpi\0 "                                                  \
 614 "workingaddr=0x02F00000\0"                                              \
 615 "workingbootargs=root=/dev/mtdblock1 rootfstype=cramfs ro\0"
 616
 617 #else
 618
 619 #if defined(CONFIG_UCP1020T1)
 620
 621 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
 622 "bootcmd=run releasefpga; run norbootworking || run norbootrecovery\0"  \
 623 "bootfile=uImage\0"                                                     \
 624 "consoledev=ttyS0\0"                                                    \
 625 "cramfsfile=image.cramfs\0"                                             \
 626 "dtbaddr=0x00c00000\0"                                                  \
 627 "dtbfile=image.dtb\0"                                                   \
 628 "ethaddr=" __stringify(CONFIG_ETHADDR) "\0"                             \
 629 "eth1addr=" __stringify(CONFIG_ETH1ADDR) "\0"                           \
 630 "eth2addr=" __stringify(CONFIG_ETH2ADDR) "\0"                           \
 631 "fileaddr=0x01000000\0"                                                 \
 632 "filesize=0x00080000\0"                                                 \
 633 "flashmbr=sf probe 0; "                                                 \
 634         "tftp $loadaddr $mbr; "                                         \
 635         "sf erase $mbr_offset +$filesize; "                             \
 636         "sf write $loadaddr $mbr_offset $filesize\0"                    \
 637 "flashrecovery=tftp $recoveryaddr $cramfsfile; "                        \
 638         "protect off $nor_recoveryaddr +$filesize; "                    \
 639         "erase $nor_recoveryaddr +$filesize; "                          \
 640         "cp.b $recoveryaddr $nor_recoveryaddr $filesize; "              \
 641         "protect on $nor_recoveryaddr +$filesize\0 "                    \
 642 "flashuboot=tftp $ubootaddr $ubootfile; "                               \
 643         "protect off $nor_ubootaddr +$filesize; "                       \
 644         "erase $nor_ubootaddr +$filesize; "                             \
 645         "cp.b $ubootaddr $nor_ubootaddr $filesize; "                    \
 646         "protect on $nor_ubootaddr +$filesize\0 "                       \
 647 "flashworking=tftp $workingaddr $cramfsfile; "                          \
 648         "protect off $nor_workingaddr +$filesize; "                     \
 649         "erase $nor_workingaddr +$filesize; "                           \
 650         "cp.b $workingaddr $nor_workingaddr $filesize; "                \
 651         "protect on $nor_workingaddr +$filesize\0 "                     \
 652 "hwconfig=usb1:dr_mode=host,phy_type=ulpi\0 "                           \
 653 "kerneladdr=0x01100000\0"                                               \
 654 "kernelfile=uImage\0"                                                   \
 655 "loadaddr=0x01000000\0"                                                 \
 656 "mbr=uCP1020.mbr\0"                                                     \
 657 "mbr_offset=0x00000000\0"                                               \
 658 "netdev=eth0\0"                                                         \
 659 "nor_recoveryaddr=0xEC0A0000\0"                                         \
 660 "nor_ubootaddr=0xEFF80000\0"                                            \
 661 "nor_workingaddr=0xECFA0000\0"                                          \
 662 "norbootrecovery=setenv bootargs $recoverybootargs"                     \
 663         " console=$consoledev,$baudrate $othbootargs; "                 \
 664         "run norloadrecovery; "                                         \
 665         "bootm $kerneladdr - $dtbaddr\0"                                \
 666 "norbootworking=setenv bootargs $workingbootargs"                       \
 667         " console=$consoledev,$baudrate $othbootargs; "                 \
 668         "run norloadworking; "                                          \
 669         "bootm $kerneladdr - $dtbaddr\0"                                \
 670 "norloadrecovery=mw.l $kerneladdr 0x0 0x00a00000; "                     \
 671         "setenv cramfsaddr $nor_recoveryaddr; "                         \
 672         "cramfsload $dtbaddr $dtbfile; "                                \
 673         "cramfsload $kerneladdr $kernelfile\0"                          \
 674 "norloadworking=mw.l $kerneladdr 0x0 0x00a00000; "                      \
 675         "setenv cramfsaddr $nor_workingaddr; "                          \
 676         "cramfsload $dtbaddr $dtbfile; "                                \
 677         "cramfsload $kerneladdr $kernelfile\0"                          \
 678 "othbootargs=quiet\0"                                                   \
 679 "ramboot=setenv bootargs root=/dev/ram ramdisk_size=$ramdisk_size ro"   \
 680         " console=$consoledev,$baudrate $othbootargs; "                 \
 681         "tftp $rootfsaddr $rootfsfile; "                                \
 682         "tftp $loadaddr $kernelfile; "                                  \
 683         "tftp $dtbaddr $dtbfile; "                                      \
 684         "bootm $loadaddr $rootfsaddr $dtbaddr\0"                        \
 685 "ramdisk_size=120000\0"                                                 \
 686 "ramdiskfile=rootfs.ext2.gz.uboot\0"                                    \
 687 "recoveryaddr=0x02F00000\0"                                             \
 688 "recoverybootargs=root=/dev/mtdblock0 rootfstype=cramfs ro\0"           \
 689 "releasefpga=mw.l 0xffe0f000 0x00400000; mw.l 0xffe0f004 0x00000000; "  \
 690         "mw.l 0xffe0f008 0x00400000\0"                                  \
 691 "rootfsaddr=0x02F00000\0"                                               \
 692 "rootfsfile=rootfs.ext2.gz.uboot\0"                                     \
 693 "rootpath=/opt/nfsroot\0"                                               \
 694 "silent=1\0"                                                            \
 695 "tftpflash=tftpboot $loadaddr $uboot; "                                 \
 696         "protect off " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
 697         "erase " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; "  \
 698         "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize; " \
 699         "protect on " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
 700         "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize\0"\
 701 "uboot= " __stringify(CONFIG_UBOOTPATH) "\0"                            \
 702 "ubootaddr=0x01000000\0"                                                \
 703 "ubootfile=u-boot.bin\0"                                                \
 704 "upgrade=run flashworking\0"                                            \
 705 "workingaddr=0x02F00000\0"                                              \
 706 "workingbootargs=root=/dev/mtdblock1 rootfstype=cramfs ro\0"
 707
 708 #else /* For Arcturus Modules */
 709
 710 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
 711 "bootcmd=run norkernel\0"                                               \
 712 "bootfile=uImage\0"                                                     \
 713 "consoledev=ttyS0\0"                                                    \
 714 "dtbaddr=0x00c00000\0"                                                  \
 715 "dtbfile=image.dtb\0"                                                   \
 716 "ethaddr=" __stringify(CONFIG_ETHADDR) "\0"                             \
 717 "eth1addr=" __stringify(CONFIG_ETH1ADDR) "\0"                           \
 718 "eth2addr=" __stringify(CONFIG_ETH2ADDR) "\0"                           \
 719 "fileaddr=0x01000000\0"                                                 \
 720 "filesize=0x00080000\0"                                                 \
 721 "flashmbr=sf probe 0; "                                                 \
 722         "tftp $loadaddr $mbr; "                                         \
 723         "sf erase $mbr_offset +$filesize; "                             \
 724         "sf write $loadaddr $mbr_offset $filesize\0"                    \
 725 "flashuboot=tftp $loadaddr $ubootfile; "                                \
 726         "protect off $nor_ubootaddr0 +$filesize; "                      \
 727         "erase $nor_ubootaddr0 +$filesize; "                            \
 728         "cp.b $loadaddr $nor_ubootaddr0 $filesize; "                    \
 729         "protect on $nor_ubootaddr0 +$filesize; "                       \
 730         "protect off $nor_ubootaddr1 +$filesize; "                      \
 731         "erase $nor_ubootaddr1 +$filesize; "                            \
 732         "cp.b $loadaddr $nor_ubootaddr1 $filesize; "                    \
 733         "protect on $nor_ubootaddr1 +$filesize\0 "                      \
 734 "format0=protect off $part0base +$part0size; "                          \
 735         "erase $part0base +$part0size\0"                                \
 736 "format1=protect off $part1base +$part1size; "                          \
 737         "erase $part1base +$part1size\0"                                \
 738 "format2=protect off $part2base +$part2size; "                          \
 739         "erase $part2base +$part2size\0"                                \
 740 "format3=protect off $part3base +$part3size; "                          \
 741         "erase $part3base +$part3size\0"                                \
 742 "hwconfig=usb1:dr_mode=host,phy_type=ulpi\0 "                           \
 743 "kerneladdr=0x01100000\0"                                               \
 744 "kernelargs=root=/dev/mtdblock1 rootfstype=cramfs ro\0"                 \
 745 "kernelfile=uImage\0"                                                   \
 746 "loadaddr=0x01000000\0"                                                 \
 747 "mbr=uCP1020.mbr\0"                                                     \
 748 "mbr_offset=0x00000000\0"                                               \
 749 "netdev=eth0\0"                                                         \
 750 "nor_ubootaddr0=0xEC000000\0"                                           \
 751 "nor_ubootaddr1=0xEFF80000\0"                                           \
 752 "norkernel=setenv bootargs $kernelargs console=$consoledev,$baudrate; " \
 753         "run norkernelload; "                                           \
 754         "bootm $kerneladdr - $dtbaddr\0"                                \
 755 "norkernelload=mw.l $kerneladdr 0x0 0x00a00000; "                       \
 756         "setenv cramfsaddr $part0base; "                                \
 757         "cramfsload $dtbaddr $dtbfile; "                                \
 758         "cramfsload $kerneladdr $kernelfile\0"                          \
 759 "part0base=0xEC100000\0"                                                \
 760 "part0size=0x00700000\0"                                                \
 761 "part1base=0xEC800000\0"                                                \
 762 "part1size=0x02000000\0"                                                \
 763 "part2base=0xEE800000\0"                                                \
 764 "part2size=0x00800000\0"                                                \
 765 "part3base=0xEF000000\0"                                                \
 766 "part3size=0x00F80000\0"                                                \
 767 "partENVbase=0xEC080000\0"                                              \
 768 "partENVsize=0x00080000\0"                                              \
 769 "program0=tftp part0-000000.bin; "                                      \
 770         "protect off $part0base +$filesize; "                           \
 771         "erase $part0base +$filesize; "                                 \
 772         "cp.b $loadaddr $part0base $filesize; "                         \
 773         "echo Verifying...; "                                           \
 774         "cmp.b $loadaddr $part0base $filesize\0"                        \
 775 "program1=tftp part1-000000.bin; "                                      \
 776         "protect off $part1base +$filesize; "                           \
 777         "erase $part1base +$filesize; "                                 \
 778         "cp.b $loadaddr $part1base $filesize; "                         \
 779         "echo Verifying...; "                                           \
 780         "cmp.b $loadaddr $part1base $filesize\0"                        \
 781 "program2=tftp part2-000000.bin; "                                      \
 782         "protect off $part2base +$filesize; "                           \
 783         "erase $part2base +$filesize; "                                 \
 784         "cp.b $loadaddr $part2base $filesize; "                         \
 785         "echo Verifying...; "                                           \
 786         "cmp.b $loadaddr $part2base $filesize\0"                        \
 787 "ramboot=setenv bootargs root=/dev/ram ramdisk_size=$ramdisk_size ro"   \
 788         "  console=$consoledev,$baudrate $othbootargs; "                \
 789         "tftp $rootfsaddr $rootfsfile; "                                \
 790         "tftp $loadaddr $kernelfile; "                                  \
 791         "tftp $dtbaddr $dtbfile; "                                      \
 792         "bootm $loadaddr $rootfsaddr $dtbaddr\0"                        \
 793 "ramdisk_size=120000\0"                                                 \
 794 "ramdiskfile=rootfs.ext2.gz.uboot\0"                                    \
 795 "releasefpga=mw.l 0xffe0f000 0x00400000; mw.l 0xffe0f004 0x00000000; "  \
 796         "mw.l 0xffe0f008 0x00400000\0"                                  \
 797 "rootfsaddr=0x02F00000\0"                                               \
 798 "rootfsfile=rootfs.ext2.gz.uboot\0"                                     \
 799 "rootpath=/opt/nfsroot\0"                                               \
 800 "spi__mbr=fatload mmc $mmcpart $loadaddr $mmbr; "                       \
 801         "sf probe 0; sf erase 0 +$filesize; "                           \
 802         "sf write $loadaddr 0 $filesize\0"                              \
 803 "spi__boot=fatload mmc $mmcpart $loadaddr u-boot.bin; "                 \
 804         "protect off 0xeC000000 +$filesize; "                           \
 805         "erase 0xEC000000 +$filesize; "                                 \
 806         "cp.b $loadaddr 0xEC000000 $filesize; "                         \
 807         "cmp.b $loadaddr 0xEC000000 $filesize; "                        \
 808         "protect on 0xeC000000 +$filesize\0"                            \
 809 "tftpflash=tftpboot $loadaddr $uboot; "                                 \
 810         "protect off " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
 811         "erase " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; "  \
 812         "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize; " \
 813         "protect on " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
 814         "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize\0"\
 815 "uboot= " __stringify(CONFIG_UBOOTPATH) "\0"                            \
 816 "ubootfile=u-boot.bin\0"                                                \
 817 "upgrade=run flashuboot\0"                                              \
 818 "usb_phy_type=ulpi\0 "                                                  \
 819 "boot_nfs= "                                                            \
 820         "setenv bootargs root=/dev/nfs rw "                             \
 821         "nfsroot=$serverip:$rootpath "                                  \
 822         "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
 823         "console=$consoledev,$baudrate $othbootargs;"                   \
 824         "tftp $loadaddr $bootfile;"                                     \
 825         "tftp $fdtaddr $fdtfile;"                                       \
 826         "bootm $loadaddr - $fdtaddr\0"                                  \
 827 "boot_hd = "                                                            \
 828         "setenv bootargs root=/dev/$bdev rw rootdelay=30 "              \
 829         "console=$consoledev,$baudrate $othbootargs;"                   \
 830         "usb start;"                                                    \
 831         "ext2load usb 0:1 $loadaddr /boot/$bootfile;"                   \
 832         "ext2load usb 0:1 $fdtaddr /boot/$fdtfile;"                     \
 833         "bootm $loadaddr - $fdtaddr\0"                                  \
 834 "boot_usb_fat = "                                                       \
 835         "setenv bootargs root=/dev/ram rw "                             \
 836         "console=$consoledev,$baudrate $othbootargs "                   \
 837         "ramdisk_size=$ramdisk_size;"                                   \
 838         "usb start;"                                                    \
 839         "fatload usb 0:2 $loadaddr $bootfile;"                          \
 840         "fatload usb 0:2 $fdtaddr $fdtfile;"                            \
 841         "fatload usb 0:2 $ramdiskaddr $ramdiskfile;"                    \
 842         "bootm $loadaddr $ramdiskaddr $fdtaddr\0 "                      \
 843 "boot_usb_ext2 = "                                                      \
 844         "setenv bootargs root=/dev/ram rw "                             \
 845         "console=$consoledev,$baudrate $othbootargs "                   \
 846         "ramdisk_size=$ramdisk_size;"                                   \
 847         "usb start;"                                                    \
 848         "ext2load usb 0:4 $loadaddr $bootfile;"                         \
 849         "ext2load usb 0:4 $fdtaddr $fdtfile;"                           \
 850         "ext2load usb 0:4 $ramdiskaddr $ramdiskfile;"                   \
 851         "bootm $loadaddr $ramdiskaddr $fdtaddr\0 "                      \
 852 "boot_nor = "                                                           \
 853         "setenv bootargs root=/dev/$jffs2nor rw "                       \
 854         "console=$consoledev,$baudrate rootfstype=jffs2 $othbootargs;"  \
 855         "bootm $norbootaddr - $norfdtaddr\0 "                           \
 856 "boot_ram = "                                                           \
 857         "setenv bootargs root=/dev/ram rw "                             \
 858         "console=$consoledev,$baudrate $othbootargs "                   \
 859         "ramdisk_size=$ramdisk_size;"                                   \
 860         "tftp $ramdiskaddr $ramdiskfile;"                               \
 861         "tftp $loadaddr $bootfile;"                                     \
 862         "tftp $fdtaddr $fdtfile;"                                       \
 863         "bootm $loadaddr $ramdiskaddr $fdtaddr\0"
 864
 865 #endif
 866 #endif
 867
 868 #endif /* __CONFIG_H */