include/configs/T208xRDB.h

   1 /* SPDX-License-Identifier: GPL-2.0+ */
   2 /*
   3  * Copyright 2014 Freescale Semiconductor, Inc.
   4  * Copyright 2020-2021 NXP
   5  */
   6
   7 /*
   8  * T2080 RDB/PCIe board configuration file
   9  */
  10
  11 #ifndef __T2080RDB_H
  12 #define __T2080RDB_H
  13
  14 #include <linux/stringify.h>
  15
  16 #define CONFIG_ICS307_REFCLK_HZ 25000000  /* ICS307 ref clk freq */
  17 #define CONFIG_FSL_SATA_V2
  18
  19 /* High Level Configuration Options */
  20 #define CONFIG_SYS_BOOK3E_HV    /* Category E.HV supported */
  21 #define CONFIG_ENABLE_36BIT_PHYS
  22
  23 #define CONFIG_SYS_FSL_CPC      /* Corenet Platform Cache */
  24 #define CONFIG_SYS_NUM_CPC      CONFIG_SYS_NUM_DDR_CTLRS
  25
  26 #ifdef CONFIG_RAMBOOT_PBL
  27 #define CONFIG_SPL_FLUSH_IMAGE
  28 #define CONFIG_SPL_PAD_TO               0x40000
  29 #define CONFIG_SPL_MAX_SIZE             0x28000
  30 #define RESET_VECTOR_OFFSET             0x27FFC
  31 #define BOOT_PAGE_OFFSET                0x27000
  32 #ifdef CONFIG_SPL_BUILD
  33 #define CONFIG_SPL_SKIP_RELOCATE
  34 #define CONFIG_SPL_COMMON_INIT_DDR
  35 #define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
  36 #endif
  37
  38 #ifdef CONFIG_MTD_RAW_NAND
  39 #define CONFIG_SYS_NAND_U_BOOT_SIZE     (768 << 10)
  40 #define CONFIG_SYS_NAND_U_BOOT_DST      0x00200000
  41 #define CONFIG_SYS_NAND_U_BOOT_START    0x00200000
  42 #define CONFIG_SYS_NAND_U_BOOT_OFFS     (256 << 10)
  43 #endif
  44
  45 #ifdef CONFIG_SPIFLASH
  46 #define        CONFIG_RESET_VECTOR_ADDRESS             0x200FFC
  47 #define CONFIG_SPL_SPI_FLASH_MINIMAL
  48 #define CONFIG_SYS_SPI_FLASH_U_BOOT_SIZE       (768 << 10)
  49 #define CONFIG_SYS_SPI_FLASH_U_BOOT_DST                (0x00200000)
  50 #define CONFIG_SYS_SPI_FLASH_U_BOOT_START      (0x00200000)
  51 #define CONFIG_SYS_SPI_FLASH_U_BOOT_OFFS       (256 << 10)
  52 #ifndef CONFIG_SPL_BUILD
  53 #define CONFIG_SYS_MPC85XX_NO_RESETVEC
  54 #endif
  55 #endif
  56
  57 #ifdef CONFIG_SDCARD
  58 #define        CONFIG_RESET_VECTOR_ADDRESS             0x200FFC
  59 #define CONFIG_SYS_MMC_U_BOOT_SIZE     (768 << 10)
  60 #define CONFIG_SYS_MMC_U_BOOT_DST      (0x00200000)
  61 #define CONFIG_SYS_MMC_U_BOOT_START    (0x00200000)
  62 #define CONFIG_SYS_MMC_U_BOOT_OFFS     (260 << 10)
  63 #ifndef CONFIG_SPL_BUILD
  64 #define CONFIG_SYS_MPC85XX_NO_RESETVEC
  65 #endif
  66 #endif
  67
  68 #endif /* CONFIG_RAMBOOT_PBL */
  69
  70 #define CONFIG_SRIO_PCIE_BOOT_MASTER
  71 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
  72 /* Set 1M boot space */
  73 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000)
  74 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \
  75                 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR)
  76 #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
  77 #endif
  78
  79 #ifndef CONFIG_RESET_VECTOR_ADDRESS
  80 #define CONFIG_RESET_VECTOR_ADDRESS     0xeffffffc
  81 #endif
  82
  83 /*
  84  * These can be toggled for performance analysis, otherwise use default.
  85  */
  86 #define CONFIG_SYS_CACHE_STASHING
  87 #define CONFIG_BTB              /* toggle branch predition */
  88 #ifdef CONFIG_DDR_ECC
  89 #define CONFIG_MEM_INIT_VALUE           0xdeadbeef
  90 #endif
  91
  92 #ifndef __ASSEMBLY__
  93 unsigned long get_board_sys_clk(void);
  94 #endif
  95
  96 #define CONFIG_SYS_CLK_FREQ     66660000
  97
  98 /*
  99  * Config the L3 Cache as L3 SRAM
 100  */
 101 #define CONFIG_SYS_INIT_L3_ADDR         0xFFFC0000
 102 #define CONFIG_SYS_L3_SIZE              (512 << 10)
 103 #define CONFIG_SPL_GD_ADDR              (CONFIG_SYS_INIT_L3_ADDR + 32 * 1024)
 104 #define SPL_ENV_ADDR                    (CONFIG_SPL_GD_ADDR + 4 * 1024)
 105 #define CONFIG_SPL_RELOC_MALLOC_ADDR    (CONFIG_SPL_GD_ADDR + 12 * 1024)
 106 #define CONFIG_SPL_RELOC_MALLOC_SIZE    (50 << 10)
 107 #define CONFIG_SPL_RELOC_STACK          (CONFIG_SPL_GD_ADDR + 64 * 1024)
 108
 109 #define CONFIG_SYS_DCSRBAR      0xf0000000
 110 #define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull
 111
 112 /* EEPROM */
 113 #define CONFIG_SYS_I2C_EEPROM_NXID
 114 #define CONFIG_SYS_EEPROM_BUS_NUM       0
 115
 116 /*
 117  * DDR Setup
 118  */
 119 #define CONFIG_VERY_BIG_RAM
 120 #define CONFIG_SYS_DDR_SDRAM_BASE       0x00000000
 121 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE
 122 #define CONFIG_DIMM_SLOTS_PER_CTLR      1
 123 #define CONFIG_CHIP_SELECTS_PER_CTRL    (4 * CONFIG_DIMM_SLOTS_PER_CTLR)
 124 #define CONFIG_SYS_SPD_BUS_NUM  0
 125 #define CONFIG_SYS_SDRAM_SIZE   2048    /* for fixed parameter use */
 126 #define SPD_EEPROM_ADDRESS1     0x51
 127 #define SPD_EEPROM_ADDRESS2     0x52
 128 #define SPD_EEPROM_ADDRESS      SPD_EEPROM_ADDRESS1
 129 #define CTRL_INTLV_PREFERED     cacheline
 130
 131 /*
 132  * IFC Definitions
 133  */
 134 #define CONFIG_SYS_FLASH_BASE           0xe8000000
 135 #define CONFIG_SYS_FLASH_BASE_PHYS      (0xf00000000ull | CONFIG_SYS_FLASH_BASE)
 136 #define CONFIG_SYS_NOR0_CSPR_EXT        (0xf)
 137 #define CONFIG_SYS_NOR0_CSPR    (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
 138                                 CSPR_PORT_SIZE_16 | \
 139                                 CSPR_MSEL_NOR | \
 140                                 CSPR_V)
 141 #define CONFIG_SYS_NOR_AMASK    IFC_AMASK(128*1024*1024)
 142
 143 /* NOR Flash Timing Params */
 144 #define CONFIG_SYS_NOR_CSOR     CSOR_NAND_TRHZ_80
 145
 146 #define CONFIG_SYS_NOR_FTIM0    (FTIM0_NOR_TACSE(0x4) | \
 147                                 FTIM0_NOR_TEADC(0x5) | \
 148                                 FTIM0_NOR_TEAHC(0x5))
 149 #define CONFIG_SYS_NOR_FTIM1    (FTIM1_NOR_TACO(0x35) | \
 150                                 FTIM1_NOR_TRAD_NOR(0x1A) |\
 151                                 FTIM1_NOR_TSEQRAD_NOR(0x13))
 152 #define CONFIG_SYS_NOR_FTIM2    (FTIM2_NOR_TCS(0x4) | \
 153                                 FTIM2_NOR_TCH(0x4) | \
 154                                 FTIM2_NOR_TWPH(0x0E) | \
 155                                 FTIM2_NOR_TWP(0x1c))
 156 #define CONFIG_SYS_NOR_FTIM3    0x0
 157
 158 #define CONFIG_SYS_FLASH_QUIET_TEST
 159 #define CONFIG_FLASH_SHOW_PROGRESS      45 /* count down from 45/5: 9..1 */
 160
 161 #define CONFIG_SYS_MAX_FLASH_BANKS      1       /* number of banks */
 162 #define CONFIG_SYS_MAX_FLASH_SECT       1024    /* sectors per device */
 163 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000   /* Flash Erase Timeout (ms) */
 164 #define CONFIG_SYS_FLASH_WRITE_TOUT     500     /* Flash Write Timeout (ms) */
 165 #define CONFIG_SYS_FLASH_EMPTY_INFO
 166 #define CONFIG_SYS_FLASH_BANKS_LIST     {CONFIG_SYS_FLASH_BASE_PHYS }
 167
 168 /* CPLD on IFC */
 169 #define CONFIG_SYS_CPLD_BASE    0xffdf0000
 170 #define CONFIG_SYS_CPLD_BASE_PHYS       (0xf00000000ull | CONFIG_SYS_CPLD_BASE)
 171 #define CONFIG_SYS_CSPR2_EXT    (0xf)
 172 #define CONFIG_SYS_CSPR2        (CSPR_PHYS_ADDR(CONFIG_SYS_CPLD_BASE) \
 173                                 | CSPR_PORT_SIZE_8 \
 174                                 | CSPR_MSEL_GPCM \
 175                                 | CSPR_V)
 176 #define CONFIG_SYS_AMASK2       IFC_AMASK(64*1024)
 177 #define CONFIG_SYS_CSOR2        0x0
 178
 179 /* CPLD Timing parameters for IFC CS2 */
 180 #define CONFIG_SYS_CS2_FTIM0            (FTIM0_GPCM_TACSE(0x0e) | \
 181                                         FTIM0_GPCM_TEADC(0x0e) | \
 182                                         FTIM0_GPCM_TEAHC(0x0e))
 183 #define CONFIG_SYS_CS2_FTIM1            (FTIM1_GPCM_TACO(0x0e) | \
 184                                         FTIM1_GPCM_TRAD(0x1f))
 185 #define CONFIG_SYS_CS2_FTIM2            (FTIM2_GPCM_TCS(0x0e) | \
 186                                         FTIM2_GPCM_TCH(0x8) | \
 187                                         FTIM2_GPCM_TWP(0x1f))
 188 #define CONFIG_SYS_CS2_FTIM3            0x0
 189
 190 /* NAND Flash on IFC */
 191 #define CONFIG_NAND_FSL_IFC
 192 #define CONFIG_SYS_NAND_BASE            0xff800000
 193 #define CONFIG_SYS_NAND_BASE_PHYS       (0xf00000000ull | CONFIG_SYS_NAND_BASE)
 194
 195 #define CONFIG_SYS_NAND_CSPR_EXT        (0xf)
 196 #define CONFIG_SYS_NAND_CSPR    (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
 197                                 | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
 198                                 | CSPR_MSEL_NAND         /* MSEL = NAND */ \
 199                                 | CSPR_V)
 200 #define CONFIG_SYS_NAND_AMASK   IFC_AMASK(64*1024)
 201
 202 #define CONFIG_SYS_NAND_CSOR    (CSOR_NAND_ECC_ENC_EN   /* ECC on encode */ \
 203                                 | CSOR_NAND_ECC_DEC_EN  /* ECC on decode */ \
 204                                 | CSOR_NAND_ECC_MODE_4  /* 4-bit ECC */     \
 205                                 | CSOR_NAND_RAL_3       /* RAL = 2Byes */   \
 206                                 | CSOR_NAND_PGS_2K      /* Page Size = 2K */\
 207                                 | CSOR_NAND_SPRZ_64     /* Spare size = 64 */\
 208                                 | CSOR_NAND_PB(64))     /*Pages Per Block = 64*/
 209
 210 #define CONFIG_SYS_NAND_ONFI_DETECTION
 211
 212 /* ONFI NAND Flash mode0 Timing Params */
 213 #define CONFIG_SYS_NAND_FTIM0           (FTIM0_NAND_TCCST(0x07) | \
 214                                         FTIM0_NAND_TWP(0x18)    | \
 215                                         FTIM0_NAND_TWCHT(0x07)  | \
 216                                         FTIM0_NAND_TWH(0x0a))
 217 #define CONFIG_SYS_NAND_FTIM1           (FTIM1_NAND_TADLE(0x32) | \
 218                                         FTIM1_NAND_TWBE(0x39)   | \
 219                                         FTIM1_NAND_TRR(0x0e)    | \
 220                                         FTIM1_NAND_TRP(0x18))
 221 #define CONFIG_SYS_NAND_FTIM2           (FTIM2_NAND_TRAD(0x0f)  | \
 222                                         FTIM2_NAND_TREH(0x0a)   | \
 223                                         FTIM2_NAND_TWHRE(0x1e))
 224 #define CONFIG_SYS_NAND_FTIM3           0x0
 225
 226 #define CONFIG_SYS_NAND_DDR_LAW         11
 227 #define CONFIG_SYS_NAND_BASE_LIST       { CONFIG_SYS_NAND_BASE }
 228 #define CONFIG_SYS_MAX_NAND_DEVICE      1
 229 #define CONFIG_SYS_NAND_BLOCK_SIZE      (512 * 1024)
 230
 231 #if defined(CONFIG_MTD_RAW_NAND)
 232 #define CONFIG_SYS_CSPR0_EXT            CONFIG_SYS_NAND_CSPR_EXT
 233 #define CONFIG_SYS_CSPR0                CONFIG_SYS_NAND_CSPR
 234 #define CONFIG_SYS_AMASK0               CONFIG_SYS_NAND_AMASK
 235 #define CONFIG_SYS_CSOR0                CONFIG_SYS_NAND_CSOR
 236 #define CONFIG_SYS_CS0_FTIM0            CONFIG_SYS_NAND_FTIM0
 237 #define CONFIG_SYS_CS0_FTIM1            CONFIG_SYS_NAND_FTIM1
 238 #define CONFIG_SYS_CS0_FTIM2            CONFIG_SYS_NAND_FTIM2
 239 #define CONFIG_SYS_CS0_FTIM3            CONFIG_SYS_NAND_FTIM3
 240 #define CONFIG_SYS_CSPR1_EXT            CONFIG_SYS_NOR0_CSPR_EXT
 241 #define CONFIG_SYS_CSPR1                CONFIG_SYS_NOR0_CSPR
 242 #define CONFIG_SYS_AMASK1               CONFIG_SYS_NOR_AMASK
 243 #define CONFIG_SYS_CSOR1                CONFIG_SYS_NOR_CSOR
 244 #define CONFIG_SYS_CS1_FTIM0            CONFIG_SYS_NOR_FTIM0
 245 #define CONFIG_SYS_CS1_FTIM1            CONFIG_SYS_NOR_FTIM1
 246 #define CONFIG_SYS_CS1_FTIM2            CONFIG_SYS_NOR_FTIM2
 247 #define CONFIG_SYS_CS1_FTIM3            CONFIG_SYS_NOR_FTIM3
 248 #else
 249 #define CONFIG_SYS_CSPR0_EXT            CONFIG_SYS_NOR0_CSPR_EXT
 250 #define CONFIG_SYS_CSPR0                CONFIG_SYS_NOR0_CSPR
 251 #define CONFIG_SYS_AMASK0               CONFIG_SYS_NOR_AMASK
 252 #define CONFIG_SYS_CSOR0                CONFIG_SYS_NOR_CSOR
 253 #define CONFIG_SYS_CS0_FTIM0            CONFIG_SYS_NOR_FTIM0
 254 #define CONFIG_SYS_CS0_FTIM1            CONFIG_SYS_NOR_FTIM1
 255 #define CONFIG_SYS_CS0_FTIM2            CONFIG_SYS_NOR_FTIM2
 256 #define CONFIG_SYS_CS0_FTIM3            CONFIG_SYS_NOR_FTIM3
 257 #define CONFIG_SYS_CSPR1_EXT            CONFIG_SYS_NAND_CSPR_EXT
 258 #define CONFIG_SYS_CSPR1                CONFIG_SYS_NAND_CSPR
 259 #define CONFIG_SYS_AMASK1               CONFIG_SYS_NAND_AMASK
 260 #define CONFIG_SYS_CSOR1                CONFIG_SYS_NAND_CSOR
 261 #define CONFIG_SYS_CS1_FTIM0            CONFIG_SYS_NAND_FTIM0
 262 #define CONFIG_SYS_CS1_FTIM1            CONFIG_SYS_NAND_FTIM1
 263 #define CONFIG_SYS_CS1_FTIM2            CONFIG_SYS_NAND_FTIM2
 264 #define CONFIG_SYS_CS1_FTIM3            CONFIG_SYS_NAND_FTIM3
 265 #endif
 266
 267 #if defined(CONFIG_RAMBOOT_PBL)
 268 #define CONFIG_SYS_RAMBOOT
 269 #endif
 270
 271 #ifdef CONFIG_SPL_BUILD
 272 #define CONFIG_SYS_MONITOR_BASE  CONFIG_SPL_TEXT_BASE
 273 #else
 274 #define CONFIG_SYS_MONITOR_BASE  CONFIG_SYS_TEXT_BASE /* start of monitor */
 275 #endif
 276
 277 #define CONFIG_HWCONFIG
 278
 279 /* define to use L1 as initial stack */
 280 #define CONFIG_L1_INIT_RAM
 281 #define CONFIG_SYS_INIT_RAM_LOCK
 282 #define CONFIG_SYS_INIT_RAM_ADDR        0xfdd00000 /* Initial L1 address */
 283 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH      0xf
 284 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW       0xfe03c000
 285 /* The assembler doesn't like typecast */
 286 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
 287                         ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
 288                         CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
 289 #define CONFIG_SYS_INIT_RAM_SIZE        0x00004000
 290 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - \
 291                                                 GENERATED_GBL_DATA_SIZE)
 292 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 293 #define CONFIG_SYS_MONITOR_LEN          (768 * 1024)
 294
 295 /*
 296  * Serial Port
 297  */
 298 #define CONFIG_SYS_NS16550_SERIAL
 299 #define CONFIG_SYS_NS16550_REG_SIZE     1
 300 #define CONFIG_SYS_NS16550_CLK          (get_bus_freq(0)/2)
 301 #define CONFIG_SYS_BAUDRATE_TABLE       \
 302         {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
 303 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500)
 304 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600)
 305 #define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500)
 306 #define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600)
 307
 308 /*
 309  * I2C
 310  */
 311
 312 #define I2C_MUX_PCA_ADDR_PRI    0x77 /* I2C bus multiplexer,primary */
 313 #define I2C_MUX_PCA_ADDR_SEC1   0x75 /* I2C bus multiplexer,secondary 1 */
 314 #define I2C_MUX_PCA_ADDR_SEC2   0x76 /* I2C bus multiplexer,secondary 2 */
 315 #define I2C_MUX_CH_DEFAULT      0x8
 316
 317 #define I2C_MUX_CH_VOL_MONITOR  0xa
 318
 319 #define CONFIG_VID_FLS_ENV              "t208xrdb_vdd_mv"
 320 #ifndef CONFIG_SPL_BUILD
 321 #define CONFIG_VID
 322 #endif
 323 #define CONFIG_VOL_MONITOR_IR36021_SET
 324 #define CONFIG_VOL_MONITOR_IR36021_READ
 325 /* The lowest and highest voltage allowed for T208xRDB */
 326 #define VDD_MV_MIN                      819
 327 #define VDD_MV_MAX                      1212
 328
 329 /*
 330  * RapidIO
 331  */
 332 #define CONFIG_SYS_SRIO1_MEM_VIRT       0xa0000000
 333 #define CONFIG_SYS_SRIO1_MEM_PHYS       0xc20000000ull
 334 #define CONFIG_SYS_SRIO1_MEM_SIZE       0x10000000 /* 256M */
 335 #define CONFIG_SYS_SRIO2_MEM_VIRT       0xb0000000
 336 #define CONFIG_SYS_SRIO2_MEM_PHYS       0xc30000000ull
 337 #define CONFIG_SYS_SRIO2_MEM_SIZE       0x10000000 /* 256M */
 338 /*
 339  * for slave u-boot IMAGE instored in master memory space,
 340  * PHYS must be aligned based on the SIZE
 341  */
 342 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull
 343 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull
 344 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE     0x100000 /* 1M */
 345 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull
 346 /*
 347  * for slave UCODE and ENV instored in master memory space,
 348  * PHYS must be aligned based on the SIZE
 349  */
 350 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull
 351 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull
 352 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE    0x40000 /* 256K */
 353
 354 /* slave core release by master*/
 355 #define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4
 356 #define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */
 357
 358 /*
 359  * SRIO_PCIE_BOOT - SLAVE
 360  */
 361 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
 362 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000
 363 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \
 364                 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR)
 365 #endif
 366
 367 /*
 368  * eSPI - Enhanced SPI
 369  */
 370
 371 /*
 372  * General PCI
 373  * Memory space is mapped 1-1, but I/O space must start from 0.
 374  */
 375 #define CONFIG_PCIE1            /* PCIE controller 1 */
 376 #define CONFIG_PCIE2            /* PCIE controller 2 */
 377 #define CONFIG_PCIE3            /* PCIE controller 3 */
 378 #define CONFIG_PCIE4            /* PCIE controller 4 */
 379 #define CONFIG_SYS_PCI_64BIT    /* enable 64-bit PCI resources */
 380 /* controller 1, direct to uli, tgtid 3, Base address 20000 */
 381 #define CONFIG_SYS_PCIE1_MEM_VIRT       0x80000000
 382 #define CONFIG_SYS_PCIE1_MEM_PHYS       0xc00000000ull
 383 #define CONFIG_SYS_PCIE1_IO_VIRT        0xf8000000
 384 #define CONFIG_SYS_PCIE1_IO_PHYS        0xff8000000ull
 385
 386 /* controller 2, Slot 2, tgtid 2, Base address 201000 */
 387 #define CONFIG_SYS_PCIE2_MEM_VIRT       0xa0000000
 388 #define CONFIG_SYS_PCIE2_MEM_PHYS       0xc20000000ull
 389 #define CONFIG_SYS_PCIE2_IO_VIRT        0xf8010000
 390 #define CONFIG_SYS_PCIE2_IO_PHYS        0xff8010000ull
 391
 392 /* controller 3, Slot 1, tgtid 1, Base address 202000 */
 393 #define CONFIG_SYS_PCIE3_MEM_VIRT       0xb0000000
 394 #define CONFIG_SYS_PCIE3_MEM_PHYS       0xc30000000ull
 395 #define CONFIG_SYS_PCIE3_IO_VIRT        0xf8020000
 396 #define CONFIG_SYS_PCIE3_IO_PHYS        0xff8020000ull
 397
 398 /* controller 4, Base address 203000 */
 399 #define CONFIG_SYS_PCIE4_MEM_VIRT       0xc0000000
 400 #define CONFIG_SYS_PCIE4_MEM_PHYS       0xc40000000ull
 401 #define CONFIG_SYS_PCIE4_IO_PHYS        0xff8030000ull
 402
 403 #ifdef CONFIG_PCI
 404 #define CONFIG_PCI_SCAN_SHOW    /* show pci devices on startup */
 405 #endif
 406
 407 /* Qman/Bman */
 408 #ifndef CONFIG_NOBQFMAN
 409 #define CONFIG_SYS_BMAN_NUM_PORTALS     18
 410 #define CONFIG_SYS_BMAN_MEM_BASE        0xf4000000
 411 #define CONFIG_SYS_BMAN_MEM_PHYS        0xff4000000ull
 412 #define CONFIG_SYS_BMAN_MEM_SIZE        0x02000000
 413 #define CONFIG_SYS_BMAN_SP_CENA_SIZE    0x4000
 414 #define CONFIG_SYS_BMAN_SP_CINH_SIZE    0x1000
 415 #define CONFIG_SYS_BMAN_CENA_BASE       CONFIG_SYS_BMAN_MEM_BASE
 416 #define CONFIG_SYS_BMAN_CENA_SIZE       (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
 417 #define CONFIG_SYS_BMAN_CINH_BASE       (CONFIG_SYS_BMAN_MEM_BASE + \
 418                                         CONFIG_SYS_BMAN_CENA_SIZE)
 419 #define CONFIG_SYS_BMAN_CINH_SIZE       (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
 420 #define CONFIG_SYS_BMAN_SWP_ISDR_REG    0xE08
 421 #define CONFIG_SYS_QMAN_NUM_PORTALS     18
 422 #define CONFIG_SYS_QMAN_MEM_BASE        0xf6000000
 423 #define CONFIG_SYS_QMAN_MEM_PHYS        0xff6000000ull
 424 #define CONFIG_SYS_QMAN_MEM_SIZE        0x02000000
 425 #define CONFIG_SYS_QMAN_SP_CENA_SIZE    0x4000
 426 #define CONFIG_SYS_QMAN_SP_CINH_SIZE    0x1000
 427 #define CONFIG_SYS_QMAN_CENA_BASE       CONFIG_SYS_QMAN_MEM_BASE
 428 #define CONFIG_SYS_QMAN_CENA_SIZE       (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
 429 #define CONFIG_SYS_QMAN_CINH_BASE       (CONFIG_SYS_QMAN_MEM_BASE + \
 430                                         CONFIG_SYS_QMAN_CENA_SIZE)
 431 #define CONFIG_SYS_QMAN_CINH_SIZE       (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
 432 #define CONFIG_SYS_QMAN_SWP_ISDR_REG    0xE08
 433
 434 #define CONFIG_SYS_DPAA_FMAN
 435 #define CONFIG_SYS_DPAA_PME
 436 #define CONFIG_SYS_PMAN
 437 #define CONFIG_SYS_DPAA_DCE
 438 #define CONFIG_SYS_DPAA_RMAN            /* RMan */
 439 #define CONFIG_SYS_INTERLAKEN
 440
 441 /* Default address of microcode for the Linux Fman driver */
 442 #if defined(CONFIG_SPIFLASH)
 443 /*
 444  * env is stored at 0x100000, sector size is 0x10000, ucode is stored after
 445  * env, so we got 0x110000.
 446  */
 447 #define CONFIG_SYS_FMAN_FW_ADDR         0x110000
 448
 449 #elif defined(CONFIG_SDCARD)
 450 /*
 451  * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
 452  * about 1MB (2048 blocks), Env is stored after the image, and the env size is
 453  * 0x2000 (16 blocks), 8 + 2048 + 16 = 2072, enlarge it to 2080.
 454  */
 455 #define CONFIG_SYS_FMAN_FW_ADDR         (512 * 0x820)
 456
 457 #elif defined(CONFIG_MTD_RAW_NAND)
 458 #define CONFIG_SYS_FMAN_FW_ADDR         (3 * CONFIG_SYS_NAND_BLOCK_SIZE)
 459 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
 460 /*
 461  * Slave has no ucode locally, it can fetch this from remote. When implementing
 462  * in two corenet boards, slave's ucode could be stored in master's memory
 463  * space, the address can be mapped from slave TLB->slave LAW->
 464  * slave SRIO or PCIE outbound window->master inbound window->
 465  * master LAW->the ucode address in master's memory space.
 466  */
 467 #define CONFIG_SYS_FMAN_FW_ADDR         0xFFE00000
 468 #else
 469 #define CONFIG_SYS_FMAN_FW_ADDR         0xEFF00000
 470 #endif
 471 #define CONFIG_SYS_QE_FMAN_FW_LENGTH    0x10000
 472 #define CONFIG_SYS_FDT_PAD              (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
 473 #endif /* CONFIG_NOBQFMAN */
 474
 475 #ifdef CONFIG_SYS_DPAA_FMAN
 476 #define RGMII_PHY1_ADDR         0x01  /* RealTek RTL8211E */
 477 #define RGMII_PHY2_ADDR         0x02
 478 #define CORTINA_PHY_ADDR1       0x0c  /* Cortina CS4315 */
 479 #define CORTINA_PHY_ADDR2       0x0d
 480 /* Aquantia AQ1202 10G Base-T used by board revisions up to C */
 481 #define FM1_10GEC3_PHY_ADDR     0x00
 482 #define FM1_10GEC4_PHY_ADDR     0x01
 483 /* Aquantia AQR113C 10G Base-T used by board revisions D and up */
 484 #define AQR113C_PHY_ADDR1       0x00
 485 #define AQR113C_PHY_ADDR2       0x08
 486 #endif
 487
 488 #ifdef CONFIG_FMAN_ENET
 489 #define CONFIG_ETHPRIME         "FM1@DTSEC3"
 490 #endif
 491
 492 /*
 493  * SATA
 494  */
 495 #ifdef CONFIG_FSL_SATA_V2
 496 #define CONFIG_SYS_SATA_MAX_DEVICE      2
 497 #define CONFIG_SATA1
 498 #define CONFIG_SYS_SATA1                CONFIG_SYS_MPC85xx_SATA1_ADDR
 499 #define CONFIG_SYS_SATA1_FLAGS          FLAGS_DMA
 500 #define CONFIG_SATA2
 501 #define CONFIG_SYS_SATA2                CONFIG_SYS_MPC85xx_SATA2_ADDR
 502 #define CONFIG_SYS_SATA2_FLAGS          FLAGS_DMA
 503 #define CONFIG_LBA48
 504 #endif
 505
 506 /*
 507  * USB
 508  */
 509 #ifdef CONFIG_USB_EHCI_HCD
 510 #define CONFIG_USB_EHCI_FSL
 511 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 512 #define CONFIG_HAS_FSL_DR_USB
 513 #endif
 514
 515 /*
 516  * SDHC
 517  */
 518 #ifdef CONFIG_MMC
 519 #define CONFIG_SYS_FSL_ESDHC_ADDR       CONFIG_SYS_MPC85xx_ESDHC_ADDR
 520 #define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT
 521 #endif
 522
 523 /*
 524  * Dynamic MTD Partition support with mtdparts
 525  */
 526
 527 /*
 528  * Environment
 529  */
 530
 531 /*
 532  * Miscellaneous configurable options
 533  */
 534
 535 /*
 536  * For booting Linux, the board info and command line data
 537  * have to be in the first 64 MB of memory, since this is
 538  * the maximum mapped by the Linux kernel during initialization.
 539  */
 540 #define CONFIG_SYS_BOOTMAPSZ    (64 << 20)      /* Initial map for Linux*/
 541 #define CONFIG_SYS_BOOTM_LEN    (64 << 20)      /* Increase max gunzip size */
 542
 543 /*
 544  * Environment Configuration
 545  */
 546 #define CONFIG_ROOTPATH  "/opt/nfsroot"
 547 #define CONFIG_BOOTFILE  "uImage"
 548 #define CONFIG_UBOOTPATH "u-boot.bin"   /* U-Boot image on TFTP server */
 549
 550 #define __USB_PHY_TYPE          utmi
 551
 552 #define CONFIG_EXTRA_ENV_SETTINGS                               \
 553         "hwconfig=fsl_ddr:"                                     \
 554         "ctlr_intlv=" __stringify(CTRL_INTLV_PREFERED) ","      \
 555         "bank_intlv=auto;"                                      \
 556         "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\
 557         "netdev=eth0\0"                                         \
 558         "uboot=" __stringify(CONFIG_UBOOTPATH) "\0"             \
 559         "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0"     \
 560         "tftpflash=tftpboot $loadaddr $uboot && "               \
 561         "protect off $ubootaddr +$filesize && "                 \
 562         "erase $ubootaddr +$filesize && "                       \
 563         "cp.b $loadaddr $ubootaddr $filesize && "               \
 564         "protect on $ubootaddr +$filesize && "                  \
 565         "cmp.b $loadaddr $ubootaddr $filesize\0"                \
 566         "consoledev=ttyS0\0"                                    \
 567         "ramdiskaddr=2000000\0"                                 \
 568         "ramdiskfile=t2080rdb/ramdisk.uboot\0"                  \
 569         "fdtaddr=1e00000\0"                                     \
 570         "fdtfile=t2080rdb/t2080rdb.dtb\0"                       \
 571         "bdev=sda3\0"
 572
 573 /*
 574  * For emulation this causes u-boot to jump to the start of the
 575  * proof point app code automatically
 576  */
 577 #define PROOF_POINTS                            \
 578         "setenv bootargs root=/dev/$bdev rw "           \
 579         "console=$consoledev,$baudrate $othbootargs;"   \
 580         "cpu 1 release 0x29000000 - - -;"               \
 581         "cpu 2 release 0x29000000 - - -;"               \
 582         "cpu 3 release 0x29000000 - - -;"               \
 583         "cpu 4 release 0x29000000 - - -;"               \
 584         "cpu 5 release 0x29000000 - - -;"               \
 585         "cpu 6 release 0x29000000 - - -;"               \
 586         "cpu 7 release 0x29000000 - - -;"               \
 587         "go 0x29000000"
 588
 589 #define HVBOOT                          \
 590         "setenv bootargs config-addr=0x60000000; "      \
 591         "bootm 0x01000000 - 0x00f00000"
 592
 593 #define ALU                             \
 594         "setenv bootargs root=/dev/$bdev rw "           \
 595         "console=$consoledev,$baudrate $othbootargs;"   \
 596         "cpu 1 release 0x01000000 - - -;"               \
 597         "cpu 2 release 0x01000000 - - -;"               \
 598         "cpu 3 release 0x01000000 - - -;"               \
 599         "cpu 4 release 0x01000000 - - -;"               \
 600         "cpu 5 release 0x01000000 - - -;"               \
 601         "cpu 6 release 0x01000000 - - -;"               \
 602         "cpu 7 release 0x01000000 - - -;"               \
 603         "go 0x01000000"
 604
 605 #define LINUXBOOTCOMMAND                                \
 606         "setenv bootargs root=/dev/ram rw "             \
 607         "console=$consoledev,$baudrate $othbootargs;"   \
 608         "setenv ramdiskaddr 0x02000000;"                \
 609         "setenv fdtaddr 0x00c00000;"                    \
 610         "setenv loadaddr 0x1000000;"                    \
 611         "bootm $loadaddr $ramdiskaddr $fdtaddr"
 612
 613 #define HDBOOT                                  \
 614         "setenv bootargs root=/dev/$bdev rw "           \
 615         "console=$consoledev,$baudrate $othbootargs;"   \
 616         "tftp $loadaddr $bootfile;"                     \
 617         "tftp $fdtaddr $fdtfile;"                       \
 618         "bootm $loadaddr - $fdtaddr"
 619
 620 #define NFSBOOTCOMMAND                  \
 621         "setenv bootargs root=/dev/nfs rw "     \
 622         "nfsroot=$serverip:$rootpath "          \
 623         "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
 624         "console=$consoledev,$baudrate $othbootargs;"   \
 625         "tftp $loadaddr $bootfile;"             \
 626         "tftp $fdtaddr $fdtfile;"               \
 627         "bootm $loadaddr - $fdtaddr"
 628
 629 #define RAMBOOTCOMMAND                          \
 630         "setenv bootargs root=/dev/ram rw "             \
 631         "console=$consoledev,$baudrate $othbootargs;"   \
 632         "tftp $ramdiskaddr $ramdiskfile;"               \
 633         "tftp $loadaddr $bootfile;"                     \
 634         "tftp $fdtaddr $fdtfile;"                       \
 635         "bootm $loadaddr $ramdiskaddr $fdtaddr"
 636
 637 #define CONFIG_BOOTCOMMAND              LINUXBOOTCOMMAND
 638
 639 #include <asm/fsl_secure_boot.h>
 640
 641 #endif  /* __T2080RDB_H */