include/configs/T208xRDB.h

   1 /* SPDX-License-Identifier: GPL-2.0+ */
   2 /*
   3  * Copyright 2014 Freescale Semiconductor, Inc.
   4  * Copyright 2020-2021 NXP
   5  */
   6
   7 /*
   8  * T2080 RDB/PCIe board configuration file
   9  */
  10
  11 #ifndef __T2080RDB_H
  12 #define __T2080RDB_H
  13
  14 #include <linux/stringify.h>
  15
  16 #define CONFIG_ICS307_REFCLK_HZ 25000000  /* ICS307 ref clk freq */
  17 #define CONFIG_FSL_SATA_V2
  18
  19 /* High Level Configuration Options */
  20 #define CONFIG_SYS_BOOK3E_HV    /* Category E.HV supported */
  21 #define CONFIG_ENABLE_36BIT_PHYS
  22
  23 #define CONFIG_SYS_FSL_CPC      /* Corenet Platform Cache */
  24 #define CONFIG_SYS_NUM_CPC      CONFIG_SYS_NUM_DDR_CTLRS
  25
  26 #ifdef CONFIG_RAMBOOT_PBL
  27 #define CONFIG_SPL_FLUSH_IMAGE
  28 #define CONFIG_SPL_PAD_TO               0x40000
  29 #define CONFIG_SPL_MAX_SIZE             0x28000
  30 #define RESET_VECTOR_OFFSET             0x27FFC
  31 #define BOOT_PAGE_OFFSET                0x27000
  32 #ifdef CONFIG_SPL_BUILD
  33 #define CONFIG_SPL_SKIP_RELOCATE
  34 #define CONFIG_SPL_COMMON_INIT_DDR
  35 #define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
  36 #endif
  37
  38 #ifdef CONFIG_MTD_RAW_NAND
  39 #define CONFIG_SYS_NAND_U_BOOT_SIZE     (768 << 10)
  40 #define CONFIG_SYS_NAND_U_BOOT_DST      0x00200000
  41 #define CONFIG_SYS_NAND_U_BOOT_START    0x00200000
  42 #endif
  43
  44 #ifdef CONFIG_SPIFLASH
  45 #define        CONFIG_RESET_VECTOR_ADDRESS             0x200FFC
  46 #define CONFIG_SPL_SPI_FLASH_MINIMAL
  47 #define CONFIG_SYS_SPI_FLASH_U_BOOT_SIZE       (768 << 10)
  48 #define CONFIG_SYS_SPI_FLASH_U_BOOT_DST                (0x00200000)
  49 #define CONFIG_SYS_SPI_FLASH_U_BOOT_START      (0x00200000)
  50 #define CONFIG_SYS_SPI_FLASH_U_BOOT_OFFS       (256 << 10)
  51 #ifndef CONFIG_SPL_BUILD
  52 #define CONFIG_SYS_MPC85XX_NO_RESETVEC
  53 #endif
  54 #endif
  55
  56 #ifdef CONFIG_SDCARD
  57 #define        CONFIG_RESET_VECTOR_ADDRESS             0x200FFC
  58 #define CONFIG_SYS_MMC_U_BOOT_SIZE     (768 << 10)
  59 #define CONFIG_SYS_MMC_U_BOOT_DST      (0x00200000)
  60 #define CONFIG_SYS_MMC_U_BOOT_START    (0x00200000)
  61 #define CONFIG_SYS_MMC_U_BOOT_OFFS     (260 << 10)
  62 #ifndef CONFIG_SPL_BUILD
  63 #define CONFIG_SYS_MPC85XX_NO_RESETVEC
  64 #endif
  65 #endif
  66
  67 #endif /* CONFIG_RAMBOOT_PBL */
  68
  69 #define CONFIG_SRIO_PCIE_BOOT_MASTER
  70 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
  71 /* Set 1M boot space */
  72 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000)
  73 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \
  74                 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR)
  75 #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
  76 #endif
  77
  78 #ifndef CONFIG_RESET_VECTOR_ADDRESS
  79 #define CONFIG_RESET_VECTOR_ADDRESS     0xeffffffc
  80 #endif
  81
  82 /*
  83  * These can be toggled for performance analysis, otherwise use default.
  84  */
  85 #define CONFIG_SYS_CACHE_STASHING
  86 #define CONFIG_BTB              /* toggle branch predition */
  87 #ifdef CONFIG_DDR_ECC
  88 #define CONFIG_MEM_INIT_VALUE           0xdeadbeef
  89 #endif
  90
  91 /*
  92  * Config the L3 Cache as L3 SRAM
  93  */
  94 #define CONFIG_SYS_INIT_L3_ADDR         0xFFFC0000
  95 #define CONFIG_SYS_L3_SIZE              (512 << 10)
  96 #define CONFIG_SPL_GD_ADDR              (CONFIG_SYS_INIT_L3_ADDR + 32 * 1024)
  97 #define SPL_ENV_ADDR                    (CONFIG_SPL_GD_ADDR + 4 * 1024)
  98 #define CONFIG_SPL_RELOC_MALLOC_ADDR    (CONFIG_SPL_GD_ADDR + 12 * 1024)
  99 #define CONFIG_SPL_RELOC_MALLOC_SIZE    (50 << 10)
 100 #define CONFIG_SPL_RELOC_STACK          (CONFIG_SPL_GD_ADDR + 64 * 1024)
 101
 102 #define CONFIG_SYS_DCSRBAR      0xf0000000
 103 #define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull
 104
 105 /* EEPROM */
 106 #define CONFIG_SYS_I2C_EEPROM_NXID
 107 #define CONFIG_SYS_EEPROM_BUS_NUM       0
 108
 109 /*
 110  * DDR Setup
 111  */
 112 #define CONFIG_VERY_BIG_RAM
 113 #define CONFIG_SYS_DDR_SDRAM_BASE       0x00000000
 114 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE
 115 #define CONFIG_DIMM_SLOTS_PER_CTLR      1
 116 #define CONFIG_CHIP_SELECTS_PER_CTRL    (4 * CONFIG_DIMM_SLOTS_PER_CTLR)
 117 #define CONFIG_SYS_SPD_BUS_NUM  0
 118 #define CONFIG_SYS_SDRAM_SIZE   2048    /* for fixed parameter use */
 119 #define SPD_EEPROM_ADDRESS1     0x51
 120 #define SPD_EEPROM_ADDRESS2     0x52
 121 #define SPD_EEPROM_ADDRESS      SPD_EEPROM_ADDRESS1
 122 #define CTRL_INTLV_PREFERED     cacheline
 123
 124 /*
 125  * IFC Definitions
 126  */
 127 #define CONFIG_SYS_FLASH_BASE           0xe8000000
 128 #define CONFIG_SYS_FLASH_BASE_PHYS      (0xf00000000ull | CONFIG_SYS_FLASH_BASE)
 129 #define CONFIG_SYS_NOR0_CSPR_EXT        (0xf)
 130 #define CONFIG_SYS_NOR0_CSPR    (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
 131                                 CSPR_PORT_SIZE_16 | \
 132                                 CSPR_MSEL_NOR | \
 133                                 CSPR_V)
 134 #define CONFIG_SYS_NOR_AMASK    IFC_AMASK(128*1024*1024)
 135
 136 /* NOR Flash Timing Params */
 137 #define CONFIG_SYS_NOR_CSOR     CSOR_NAND_TRHZ_80
 138
 139 #define CONFIG_SYS_NOR_FTIM0    (FTIM0_NOR_TACSE(0x4) | \
 140                                 FTIM0_NOR_TEADC(0x5) | \
 141                                 FTIM0_NOR_TEAHC(0x5))
 142 #define CONFIG_SYS_NOR_FTIM1    (FTIM1_NOR_TACO(0x35) | \
 143                                 FTIM1_NOR_TRAD_NOR(0x1A) |\
 144                                 FTIM1_NOR_TSEQRAD_NOR(0x13))
 145 #define CONFIG_SYS_NOR_FTIM2    (FTIM2_NOR_TCS(0x4) | \
 146                                 FTIM2_NOR_TCH(0x4) | \
 147                                 FTIM2_NOR_TWPH(0x0E) | \
 148                                 FTIM2_NOR_TWP(0x1c))
 149 #define CONFIG_SYS_NOR_FTIM3    0x0
 150
 151 #define CONFIG_SYS_FLASH_QUIET_TEST
 152 #define CONFIG_FLASH_SHOW_PROGRESS      45 /* count down from 45/5: 9..1 */
 153
 154 #define CONFIG_SYS_MAX_FLASH_SECT       1024    /* sectors per device */
 155 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000   /* Flash Erase Timeout (ms) */
 156 #define CONFIG_SYS_FLASH_WRITE_TOUT     500     /* Flash Write Timeout (ms) */
 157 #define CONFIG_SYS_FLASH_EMPTY_INFO
 158 #define CONFIG_SYS_FLASH_BANKS_LIST     {CONFIG_SYS_FLASH_BASE_PHYS }
 159
 160 /* CPLD on IFC */
 161 #define CONFIG_SYS_CPLD_BASE    0xffdf0000
 162 #define CONFIG_SYS_CPLD_BASE_PHYS       (0xf00000000ull | CONFIG_SYS_CPLD_BASE)
 163 #define CONFIG_SYS_CSPR2_EXT    (0xf)
 164 #define CONFIG_SYS_CSPR2        (CSPR_PHYS_ADDR(CONFIG_SYS_CPLD_BASE) \
 165                                 | CSPR_PORT_SIZE_8 \
 166                                 | CSPR_MSEL_GPCM \
 167                                 | CSPR_V)
 168 #define CONFIG_SYS_AMASK2       IFC_AMASK(64*1024)
 169 #define CONFIG_SYS_CSOR2        0x0
 170
 171 /* CPLD Timing parameters for IFC CS2 */
 172 #define CONFIG_SYS_CS2_FTIM0            (FTIM0_GPCM_TACSE(0x0e) | \
 173                                         FTIM0_GPCM_TEADC(0x0e) | \
 174                                         FTIM0_GPCM_TEAHC(0x0e))
 175 #define CONFIG_SYS_CS2_FTIM1            (FTIM1_GPCM_TACO(0x0e) | \
 176                                         FTIM1_GPCM_TRAD(0x1f))
 177 #define CONFIG_SYS_CS2_FTIM2            (FTIM2_GPCM_TCS(0x0e) | \
 178                                         FTIM2_GPCM_TCH(0x8) | \
 179                                         FTIM2_GPCM_TWP(0x1f))
 180 #define CONFIG_SYS_CS2_FTIM3            0x0
 181
 182 /* NAND Flash on IFC */
 183 #define CONFIG_SYS_NAND_BASE            0xff800000
 184 #define CONFIG_SYS_NAND_BASE_PHYS       (0xf00000000ull | CONFIG_SYS_NAND_BASE)
 185
 186 #define CONFIG_SYS_NAND_CSPR_EXT        (0xf)
 187 #define CONFIG_SYS_NAND_CSPR    (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
 188                                 | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
 189                                 | CSPR_MSEL_NAND         /* MSEL = NAND */ \
 190                                 | CSPR_V)
 191 #define CONFIG_SYS_NAND_AMASK   IFC_AMASK(64*1024)
 192
 193 #define CONFIG_SYS_NAND_CSOR    (CSOR_NAND_ECC_ENC_EN   /* ECC on encode */ \
 194                                 | CSOR_NAND_ECC_DEC_EN  /* ECC on decode */ \
 195                                 | CSOR_NAND_ECC_MODE_4  /* 4-bit ECC */     \
 196                                 | CSOR_NAND_RAL_3       /* RAL = 2Byes */   \
 197                                 | CSOR_NAND_PGS_2K      /* Page Size = 2K */\
 198                                 | CSOR_NAND_SPRZ_64     /* Spare size = 64 */\
 199                                 | CSOR_NAND_PB(64))     /*Pages Per Block = 64*/
 200
 201 /* ONFI NAND Flash mode0 Timing Params */
 202 #define CONFIG_SYS_NAND_FTIM0           (FTIM0_NAND_TCCST(0x07) | \
 203                                         FTIM0_NAND_TWP(0x18)    | \
 204                                         FTIM0_NAND_TWCHT(0x07)  | \
 205                                         FTIM0_NAND_TWH(0x0a))
 206 #define CONFIG_SYS_NAND_FTIM1           (FTIM1_NAND_TADLE(0x32) | \
 207                                         FTIM1_NAND_TWBE(0x39)   | \
 208                                         FTIM1_NAND_TRR(0x0e)    | \
 209                                         FTIM1_NAND_TRP(0x18))
 210 #define CONFIG_SYS_NAND_FTIM2           (FTIM2_NAND_TRAD(0x0f)  | \
 211                                         FTIM2_NAND_TREH(0x0a)   | \
 212                                         FTIM2_NAND_TWHRE(0x1e))
 213 #define CONFIG_SYS_NAND_FTIM3           0x0
 214
 215 #define CONFIG_SYS_NAND_DDR_LAW         11
 216 #define CONFIG_SYS_NAND_BASE_LIST       { CONFIG_SYS_NAND_BASE }
 217 #define CONFIG_SYS_MAX_NAND_DEVICE      1
 218
 219 #if defined(CONFIG_MTD_RAW_NAND)
 220 #define CONFIG_SYS_CSPR0_EXT            CONFIG_SYS_NAND_CSPR_EXT
 221 #define CONFIG_SYS_CSPR0                CONFIG_SYS_NAND_CSPR
 222 #define CONFIG_SYS_AMASK0               CONFIG_SYS_NAND_AMASK
 223 #define CONFIG_SYS_CSOR0                CONFIG_SYS_NAND_CSOR
 224 #define CONFIG_SYS_CS0_FTIM0            CONFIG_SYS_NAND_FTIM0
 225 #define CONFIG_SYS_CS0_FTIM1            CONFIG_SYS_NAND_FTIM1
 226 #define CONFIG_SYS_CS0_FTIM2            CONFIG_SYS_NAND_FTIM2
 227 #define CONFIG_SYS_CS0_FTIM3            CONFIG_SYS_NAND_FTIM3
 228 #define CONFIG_SYS_CSPR1_EXT            CONFIG_SYS_NOR0_CSPR_EXT
 229 #define CONFIG_SYS_CSPR1                CONFIG_SYS_NOR0_CSPR
 230 #define CONFIG_SYS_AMASK1               CONFIG_SYS_NOR_AMASK
 231 #define CONFIG_SYS_CSOR1                CONFIG_SYS_NOR_CSOR
 232 #define CONFIG_SYS_CS1_FTIM0            CONFIG_SYS_NOR_FTIM0
 233 #define CONFIG_SYS_CS1_FTIM1            CONFIG_SYS_NOR_FTIM1
 234 #define CONFIG_SYS_CS1_FTIM2            CONFIG_SYS_NOR_FTIM2
 235 #define CONFIG_SYS_CS1_FTIM3            CONFIG_SYS_NOR_FTIM3
 236 #else
 237 #define CONFIG_SYS_CSPR0_EXT            CONFIG_SYS_NOR0_CSPR_EXT
 238 #define CONFIG_SYS_CSPR0                CONFIG_SYS_NOR0_CSPR
 239 #define CONFIG_SYS_AMASK0               CONFIG_SYS_NOR_AMASK
 240 #define CONFIG_SYS_CSOR0                CONFIG_SYS_NOR_CSOR
 241 #define CONFIG_SYS_CS0_FTIM0            CONFIG_SYS_NOR_FTIM0
 242 #define CONFIG_SYS_CS0_FTIM1            CONFIG_SYS_NOR_FTIM1
 243 #define CONFIG_SYS_CS0_FTIM2            CONFIG_SYS_NOR_FTIM2
 244 #define CONFIG_SYS_CS0_FTIM3            CONFIG_SYS_NOR_FTIM3
 245 #define CONFIG_SYS_CSPR1_EXT            CONFIG_SYS_NAND_CSPR_EXT
 246 #define CONFIG_SYS_CSPR1                CONFIG_SYS_NAND_CSPR
 247 #define CONFIG_SYS_AMASK1               CONFIG_SYS_NAND_AMASK
 248 #define CONFIG_SYS_CSOR1                CONFIG_SYS_NAND_CSOR
 249 #define CONFIG_SYS_CS1_FTIM0            CONFIG_SYS_NAND_FTIM0
 250 #define CONFIG_SYS_CS1_FTIM1            CONFIG_SYS_NAND_FTIM1
 251 #define CONFIG_SYS_CS1_FTIM2            CONFIG_SYS_NAND_FTIM2
 252 #define CONFIG_SYS_CS1_FTIM3            CONFIG_SYS_NAND_FTIM3
 253 #endif
 254
 255 #if defined(CONFIG_RAMBOOT_PBL)
 256 #define CONFIG_SYS_RAMBOOT
 257 #endif
 258
 259 #ifdef CONFIG_SPL_BUILD
 260 #define CONFIG_SYS_MONITOR_BASE  CONFIG_SPL_TEXT_BASE
 261 #else
 262 #define CONFIG_SYS_MONITOR_BASE  CONFIG_SYS_TEXT_BASE /* start of monitor */
 263 #endif
 264
 265 #define CONFIG_HWCONFIG
 266
 267 /* define to use L1 as initial stack */
 268 #define CONFIG_L1_INIT_RAM
 269 #define CONFIG_SYS_INIT_RAM_LOCK
 270 #define CONFIG_SYS_INIT_RAM_ADDR        0xfdd00000 /* Initial L1 address */
 271 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH      0xf
 272 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW       0xfe03c000
 273 /* The assembler doesn't like typecast */
 274 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
 275                         ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
 276                         CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
 277 #define CONFIG_SYS_INIT_RAM_SIZE        0x00004000
 278 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - \
 279                                                 GENERATED_GBL_DATA_SIZE)
 280 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 281 #define CONFIG_SYS_MONITOR_LEN          (768 * 1024)
 282
 283 /*
 284  * Serial Port
 285  */
 286 #define CONFIG_SYS_NS16550_SERIAL
 287 #define CONFIG_SYS_NS16550_REG_SIZE     1
 288 #define CONFIG_SYS_NS16550_CLK          (get_bus_freq(0)/2)
 289 #define CONFIG_SYS_BAUDRATE_TABLE       \
 290         {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
 291 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500)
 292 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600)
 293 #define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500)
 294 #define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600)
 295
 296 /*
 297  * I2C
 298  */
 299
 300 #define I2C_MUX_PCA_ADDR_PRI    0x77 /* I2C bus multiplexer,primary */
 301 #define I2C_MUX_PCA_ADDR_SEC1   0x75 /* I2C bus multiplexer,secondary 1 */
 302 #define I2C_MUX_PCA_ADDR_SEC2   0x76 /* I2C bus multiplexer,secondary 2 */
 303 #define I2C_MUX_CH_DEFAULT      0x8
 304
 305 #define I2C_MUX_CH_VOL_MONITOR  0xa
 306
 307 /* The lowest and highest voltage allowed for T208xRDB */
 308 #define VDD_MV_MIN                      819
 309 #define VDD_MV_MAX                      1212
 310
 311 /*
 312  * RapidIO
 313  */
 314 #define CONFIG_SYS_SRIO1_MEM_VIRT       0xa0000000
 315 #define CONFIG_SYS_SRIO1_MEM_PHYS       0xc20000000ull
 316 #define CONFIG_SYS_SRIO1_MEM_SIZE       0x10000000 /* 256M */
 317 #define CONFIG_SYS_SRIO2_MEM_VIRT       0xb0000000
 318 #define CONFIG_SYS_SRIO2_MEM_PHYS       0xc30000000ull
 319 #define CONFIG_SYS_SRIO2_MEM_SIZE       0x10000000 /* 256M */
 320 /*
 321  * for slave u-boot IMAGE instored in master memory space,
 322  * PHYS must be aligned based on the SIZE
 323  */
 324 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull
 325 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull
 326 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE     0x100000 /* 1M */
 327 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull
 328 /*
 329  * for slave UCODE and ENV instored in master memory space,
 330  * PHYS must be aligned based on the SIZE
 331  */
 332 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull
 333 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull
 334 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE    0x40000 /* 256K */
 335
 336 /* slave core release by master*/
 337 #define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4
 338 #define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */
 339
 340 /*
 341  * SRIO_PCIE_BOOT - SLAVE
 342  */
 343 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
 344 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000
 345 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \
 346                 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR)
 347 #endif
 348
 349 /*
 350  * eSPI - Enhanced SPI
 351  */
 352
 353 /*
 354  * General PCI
 355  * Memory space is mapped 1-1, but I/O space must start from 0.
 356  */
 357 #define CONFIG_PCIE1            /* PCIE controller 1 */
 358 #define CONFIG_PCIE2            /* PCIE controller 2 */
 359 #define CONFIG_PCIE3            /* PCIE controller 3 */
 360 #define CONFIG_PCIE4            /* PCIE controller 4 */
 361 /* controller 1, direct to uli, tgtid 3, Base address 20000 */
 362 #define CONFIG_SYS_PCIE1_MEM_VIRT       0x80000000
 363 #define CONFIG_SYS_PCIE1_MEM_PHYS       0xc00000000ull
 364 #define CONFIG_SYS_PCIE1_IO_VIRT        0xf8000000
 365 #define CONFIG_SYS_PCIE1_IO_PHYS        0xff8000000ull
 366
 367 /* controller 2, Slot 2, tgtid 2, Base address 201000 */
 368 #define CONFIG_SYS_PCIE2_MEM_VIRT       0xa0000000
 369 #define CONFIG_SYS_PCIE2_MEM_PHYS       0xc20000000ull
 370 #define CONFIG_SYS_PCIE2_IO_VIRT        0xf8010000
 371 #define CONFIG_SYS_PCIE2_IO_PHYS        0xff8010000ull
 372
 373 /* controller 3, Slot 1, tgtid 1, Base address 202000 */
 374 #define CONFIG_SYS_PCIE3_MEM_VIRT       0xb0000000
 375 #define CONFIG_SYS_PCIE3_MEM_PHYS       0xc30000000ull
 376 #define CONFIG_SYS_PCIE3_IO_VIRT        0xf8020000
 377 #define CONFIG_SYS_PCIE3_IO_PHYS        0xff8020000ull
 378
 379 /* controller 4, Base address 203000 */
 380 #define CONFIG_SYS_PCIE4_MEM_VIRT       0xc0000000
 381 #define CONFIG_SYS_PCIE4_MEM_PHYS       0xc40000000ull
 382 #define CONFIG_SYS_PCIE4_IO_PHYS        0xff8030000ull
 383
 384 #ifdef CONFIG_PCI
 385 #define CONFIG_PCI_SCAN_SHOW    /* show pci devices on startup */
 386 #endif
 387
 388 /* Qman/Bman */
 389 #ifndef CONFIG_NOBQFMAN
 390 #define CONFIG_SYS_BMAN_NUM_PORTALS     18
 391 #define CONFIG_SYS_BMAN_MEM_BASE        0xf4000000
 392 #define CONFIG_SYS_BMAN_MEM_PHYS        0xff4000000ull
 393 #define CONFIG_SYS_BMAN_MEM_SIZE        0x02000000
 394 #define CONFIG_SYS_BMAN_SP_CENA_SIZE    0x4000
 395 #define CONFIG_SYS_BMAN_SP_CINH_SIZE    0x1000
 396 #define CONFIG_SYS_BMAN_CENA_BASE       CONFIG_SYS_BMAN_MEM_BASE
 397 #define CONFIG_SYS_BMAN_CENA_SIZE       (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
 398 #define CONFIG_SYS_BMAN_CINH_BASE       (CONFIG_SYS_BMAN_MEM_BASE + \
 399                                         CONFIG_SYS_BMAN_CENA_SIZE)
 400 #define CONFIG_SYS_BMAN_CINH_SIZE       (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
 401 #define CONFIG_SYS_BMAN_SWP_ISDR_REG    0xE08
 402 #define CONFIG_SYS_QMAN_NUM_PORTALS     18
 403 #define CONFIG_SYS_QMAN_MEM_BASE        0xf6000000
 404 #define CONFIG_SYS_QMAN_MEM_PHYS        0xff6000000ull
 405 #define CONFIG_SYS_QMAN_MEM_SIZE        0x02000000
 406 #define CONFIG_SYS_QMAN_SP_CENA_SIZE    0x4000
 407 #define CONFIG_SYS_QMAN_SP_CINH_SIZE    0x1000
 408 #define CONFIG_SYS_QMAN_CENA_BASE       CONFIG_SYS_QMAN_MEM_BASE
 409 #define CONFIG_SYS_QMAN_CENA_SIZE       (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
 410 #define CONFIG_SYS_QMAN_CINH_BASE       (CONFIG_SYS_QMAN_MEM_BASE + \
 411                                         CONFIG_SYS_QMAN_CENA_SIZE)
 412 #define CONFIG_SYS_QMAN_CINH_SIZE       (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
 413 #define CONFIG_SYS_QMAN_SWP_ISDR_REG    0xE08
 414
 415 #define CONFIG_SYS_DPAA_FMAN
 416 #define CONFIG_SYS_DPAA_PME
 417 #define CONFIG_SYS_PMAN
 418 #define CONFIG_SYS_DPAA_DCE
 419 #define CONFIG_SYS_DPAA_RMAN            /* RMan */
 420 #define CONFIG_SYS_INTERLAKEN
 421
 422 #define CONFIG_SYS_FDT_PAD              (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
 423 #endif /* CONFIG_NOBQFMAN */
 424
 425 #ifdef CONFIG_SYS_DPAA_FMAN
 426 #define RGMII_PHY1_ADDR         0x01  /* RealTek RTL8211E */
 427 #define RGMII_PHY2_ADDR         0x02
 428 #define CORTINA_PHY_ADDR1       0x0c  /* Cortina CS4315 */
 429 #define CORTINA_PHY_ADDR2       0x0d
 430 /* Aquantia AQ1202 10G Base-T used by board revisions up to C */
 431 #define FM1_10GEC3_PHY_ADDR     0x00
 432 #define FM1_10GEC4_PHY_ADDR     0x01
 433 /* Aquantia AQR113C 10G Base-T used by board revisions D and up */
 434 #define AQR113C_PHY_ADDR1       0x00
 435 #define AQR113C_PHY_ADDR2       0x08
 436 #endif
 437
 438 #ifdef CONFIG_FMAN_ENET
 439 #define CONFIG_ETHPRIME         "FM1@DTSEC3"
 440 #endif
 441
 442 /*
 443  * SATA
 444  */
 445 #ifdef CONFIG_FSL_SATA_V2
 446 #define CONFIG_SATA1
 447 #define CONFIG_SYS_SATA1                CONFIG_SYS_MPC85xx_SATA1_ADDR
 448 #define CONFIG_SYS_SATA1_FLAGS          FLAGS_DMA
 449 #define CONFIG_SATA2
 450 #define CONFIG_SYS_SATA2                CONFIG_SYS_MPC85xx_SATA2_ADDR
 451 #define CONFIG_SYS_SATA2_FLAGS          FLAGS_DMA
 452 #define CONFIG_LBA48
 453 #endif
 454
 455 /*
 456  * USB
 457  */
 458 #ifdef CONFIG_USB_EHCI_HCD
 459 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 460 #define CONFIG_HAS_FSL_DR_USB
 461 #endif
 462
 463 /*
 464  * SDHC
 465  */
 466 #ifdef CONFIG_MMC
 467 #define CONFIG_SYS_FSL_ESDHC_ADDR       CONFIG_SYS_MPC85xx_ESDHC_ADDR
 468 #define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT
 469 #endif
 470
 471 /*
 472  * Dynamic MTD Partition support with mtdparts
 473  */
 474
 475 /*
 476  * Environment
 477  */
 478
 479 /*
 480  * Miscellaneous configurable options
 481  */
 482
 483 /*
 484  * For booting Linux, the board info and command line data
 485  * have to be in the first 64 MB of memory, since this is
 486  * the maximum mapped by the Linux kernel during initialization.
 487  */
 488 #define CONFIG_SYS_BOOTMAPSZ    (64 << 20)      /* Initial map for Linux*/
 489 #define CONFIG_SYS_BOOTM_LEN    (64 << 20)      /* Increase max gunzip size */
 490
 491 /*
 492  * Environment Configuration
 493  */
 494 #define CONFIG_ROOTPATH  "/opt/nfsroot"
 495 #define CONFIG_BOOTFILE  "uImage"
 496 #define CONFIG_UBOOTPATH "u-boot.bin"   /* U-Boot image on TFTP server */
 497
 498 #define __USB_PHY_TYPE          utmi
 499
 500 #define CONFIG_EXTRA_ENV_SETTINGS                               \
 501         "hwconfig=fsl_ddr:"                                     \
 502         "ctlr_intlv=" __stringify(CTRL_INTLV_PREFERED) ","      \
 503         "bank_intlv=auto;"                                      \
 504         "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\
 505         "netdev=eth0\0"                                         \
 506         "uboot=" __stringify(CONFIG_UBOOTPATH) "\0"             \
 507         "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0"     \
 508         "tftpflash=tftpboot $loadaddr $uboot && "               \
 509         "protect off $ubootaddr +$filesize && "                 \
 510         "erase $ubootaddr +$filesize && "                       \
 511         "cp.b $loadaddr $ubootaddr $filesize && "               \
 512         "protect on $ubootaddr +$filesize && "                  \
 513         "cmp.b $loadaddr $ubootaddr $filesize\0"                \
 514         "consoledev=ttyS0\0"                                    \
 515         "ramdiskaddr=2000000\0"                                 \
 516         "ramdiskfile=t2080rdb/ramdisk.uboot\0"                  \
 517         "fdtaddr=1e00000\0"                                     \
 518         "fdtfile=t2080rdb/t2080rdb.dtb\0"                       \
 519         "bdev=sda3\0"
 520
 521 /*
 522  * For emulation this causes u-boot to jump to the start of the
 523  * proof point app code automatically
 524  */
 525 #define PROOF_POINTS                            \
 526         "setenv bootargs root=/dev/$bdev rw "           \
 527         "console=$consoledev,$baudrate $othbootargs;"   \
 528         "cpu 1 release 0x29000000 - - -;"               \
 529         "cpu 2 release 0x29000000 - - -;"               \
 530         "cpu 3 release 0x29000000 - - -;"               \
 531         "cpu 4 release 0x29000000 - - -;"               \
 532         "cpu 5 release 0x29000000 - - -;"               \
 533         "cpu 6 release 0x29000000 - - -;"               \
 534         "cpu 7 release 0x29000000 - - -;"               \
 535         "go 0x29000000"
 536
 537 #define HVBOOT                          \
 538         "setenv bootargs config-addr=0x60000000; "      \
 539         "bootm 0x01000000 - 0x00f00000"
 540
 541 #define ALU                             \
 542         "setenv bootargs root=/dev/$bdev rw "           \
 543         "console=$consoledev,$baudrate $othbootargs;"   \
 544         "cpu 1 release 0x01000000 - - -;"               \
 545         "cpu 2 release 0x01000000 - - -;"               \
 546         "cpu 3 release 0x01000000 - - -;"               \
 547         "cpu 4 release 0x01000000 - - -;"               \
 548         "cpu 5 release 0x01000000 - - -;"               \
 549         "cpu 6 release 0x01000000 - - -;"               \
 550         "cpu 7 release 0x01000000 - - -;"               \
 551         "go 0x01000000"
 552
 553 #include <asm/fsl_secure_boot.h>
 554
 555 #endif  /* __T2080RDB_H */