include/configs/T208xRDB.h

   1 /* SPDX-License-Identifier: GPL-2.0+ */
   2 /*
   3  * Copyright 2014 Freescale Semiconductor, Inc.
   4  * Copyright 2020-2021 NXP
   5  */
   6
   7 /*
   8  * T2080 RDB/PCIe board configuration file
   9  */
  10
  11 #ifndef __T2080RDB_H
  12 #define __T2080RDB_H
  13
  14 #include <linux/stringify.h>
  15
  16 #define CONFIG_ICS307_REFCLK_HZ 25000000  /* ICS307 ref clk freq */
  17 #define CONFIG_FSL_SATA_V2
  18
  19 /* High Level Configuration Options */
  20 #define CONFIG_SYS_BOOK3E_HV    /* Category E.HV supported */
  21 #define CONFIG_ENABLE_36BIT_PHYS
  22
  23 #define CONFIG_SYS_FSL_CPC      /* Corenet Platform Cache */
  24 #define CONFIG_SYS_NUM_CPC      CONFIG_SYS_NUM_DDR_CTLRS
  25
  26 #ifdef CONFIG_RAMBOOT_PBL
  27 #define RESET_VECTOR_OFFSET             0x27FFC
  28 #define BOOT_PAGE_OFFSET                0x27000
  29
  30 #ifdef CONFIG_MTD_RAW_NAND
  31 #define CONFIG_SYS_NAND_U_BOOT_SIZE     (768 << 10)
  32 #define CONFIG_SYS_NAND_U_BOOT_DST      0x00200000
  33 #define CONFIG_SYS_NAND_U_BOOT_START    0x00200000
  34 #ifndef CONFIG_MPC85XX_HAVE_RESET_VECTOR
  35 #define CONFIG_SYS_MPC85XX_NO_RESETVEC
  36 #endif
  37 #endif
  38
  39 #ifdef CONFIG_SPIFLASH
  40 #define        CONFIG_RESET_VECTOR_ADDRESS             0x200FFC
  41 #define CONFIG_SPL_SPI_FLASH_MINIMAL
  42 #define CONFIG_SYS_SPI_FLASH_U_BOOT_SIZE       (768 << 10)
  43 #define CONFIG_SYS_SPI_FLASH_U_BOOT_DST                (0x00200000)
  44 #define CONFIG_SYS_SPI_FLASH_U_BOOT_START      (0x00200000)
  45 #define CONFIG_SYS_SPI_FLASH_U_BOOT_OFFS       (256 << 10)
  46 #ifndef CONFIG_SPL_BUILD
  47 #define CONFIG_SYS_MPC85XX_NO_RESETVEC
  48 #endif
  49 #endif
  50
  51 #ifdef CONFIG_SDCARD
  52 #define        CONFIG_RESET_VECTOR_ADDRESS             0x200FFC
  53 #define CONFIG_SYS_MMC_U_BOOT_SIZE     (768 << 10)
  54 #define CONFIG_SYS_MMC_U_BOOT_DST      (0x00200000)
  55 #define CONFIG_SYS_MMC_U_BOOT_START    (0x00200000)
  56 #define CONFIG_SYS_MMC_U_BOOT_OFFS     (260 << 10)
  57 #ifndef CONFIG_SPL_BUILD
  58 #define CONFIG_SYS_MPC85XX_NO_RESETVEC
  59 #endif
  60 #endif
  61
  62 #endif /* CONFIG_RAMBOOT_PBL */
  63
  64 #define CONFIG_SRIO_PCIE_BOOT_MASTER
  65 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
  66 /* Set 1M boot space */
  67 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000)
  68 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \
  69                 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR)
  70 #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
  71 #endif
  72
  73 #ifndef CONFIG_RESET_VECTOR_ADDRESS
  74 #define CONFIG_RESET_VECTOR_ADDRESS     0xeffffffc
  75 #endif
  76
  77 /*
  78  * These can be toggled for performance analysis, otherwise use default.
  79  */
  80 #define CONFIG_SYS_CACHE_STASHING
  81 #ifdef CONFIG_DDR_ECC
  82 #define CONFIG_MEM_INIT_VALUE           0xdeadbeef
  83 #endif
  84
  85 /*
  86  * Config the L3 Cache as L3 SRAM
  87  */
  88 #define CONFIG_SYS_INIT_L3_ADDR         0xFFFC0000
  89 #define CONFIG_SYS_L3_SIZE              (512 << 10)
  90 #define CONFIG_SPL_GD_ADDR              (CONFIG_SYS_INIT_L3_ADDR + 32 * 1024)
  91 #define SPL_ENV_ADDR                    (CONFIG_SPL_GD_ADDR + 4 * 1024)
  92
  93 #define CONFIG_SYS_DCSRBAR      0xf0000000
  94 #define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull
  95
  96 /* EEPROM */
  97 #define CONFIG_SYS_I2C_EEPROM_NXID
  98 #define CONFIG_SYS_EEPROM_BUS_NUM       0
  99
 100 /*
 101  * DDR Setup
 102  */
 103 #define CONFIG_VERY_BIG_RAM
 104 #define CONFIG_SYS_DDR_SDRAM_BASE       0x00000000
 105 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE
 106 #define CONFIG_SYS_SPD_BUS_NUM  0
 107 #define CONFIG_SYS_SDRAM_SIZE   2048    /* for fixed parameter use */
 108 #define SPD_EEPROM_ADDRESS1     0x51
 109 #define SPD_EEPROM_ADDRESS2     0x52
 110 #define SPD_EEPROM_ADDRESS      SPD_EEPROM_ADDRESS1
 111 #define CTRL_INTLV_PREFERED     cacheline
 112
 113 /*
 114  * IFC Definitions
 115  */
 116 #define CONFIG_SYS_FLASH_BASE           0xe8000000
 117 #define CONFIG_SYS_FLASH_BASE_PHYS      (0xf00000000ull | CONFIG_SYS_FLASH_BASE)
 118 #define CONFIG_SYS_NOR0_CSPR_EXT        (0xf)
 119 #define CONFIG_SYS_NOR0_CSPR    (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
 120                                 CSPR_PORT_SIZE_16 | \
 121                                 CSPR_MSEL_NOR | \
 122                                 CSPR_V)
 123 #define CONFIG_SYS_NOR_AMASK    IFC_AMASK(128*1024*1024)
 124
 125 /* NOR Flash Timing Params */
 126 #define CONFIG_SYS_NOR_CSOR     CSOR_NAND_TRHZ_80
 127
 128 #define CONFIG_SYS_NOR_FTIM0    (FTIM0_NOR_TACSE(0x4) | \
 129                                 FTIM0_NOR_TEADC(0x5) | \
 130                                 FTIM0_NOR_TEAHC(0x5))
 131 #define CONFIG_SYS_NOR_FTIM1    (FTIM1_NOR_TACO(0x35) | \
 132                                 FTIM1_NOR_TRAD_NOR(0x1A) |\
 133                                 FTIM1_NOR_TSEQRAD_NOR(0x13))
 134 #define CONFIG_SYS_NOR_FTIM2    (FTIM2_NOR_TCS(0x4) | \
 135                                 FTIM2_NOR_TCH(0x4) | \
 136                                 FTIM2_NOR_TWPH(0x0E) | \
 137                                 FTIM2_NOR_TWP(0x1c))
 138 #define CONFIG_SYS_NOR_FTIM3    0x0
 139
 140 #define CONFIG_SYS_FLASH_QUIET_TEST
 141 #define CONFIG_FLASH_SHOW_PROGRESS      45 /* count down from 45/5: 9..1 */
 142
 143 #define CONFIG_SYS_MAX_FLASH_SECT       1024    /* sectors per device */
 144 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000   /* Flash Erase Timeout (ms) */
 145 #define CONFIG_SYS_FLASH_WRITE_TOUT     500     /* Flash Write Timeout (ms) */
 146 #define CONFIG_SYS_FLASH_EMPTY_INFO
 147 #define CONFIG_SYS_FLASH_BANKS_LIST     {CONFIG_SYS_FLASH_BASE_PHYS }
 148
 149 /* CPLD on IFC */
 150 #define CONFIG_SYS_CPLD_BASE    0xffdf0000
 151 #define CONFIG_SYS_CPLD_BASE_PHYS       (0xf00000000ull | CONFIG_SYS_CPLD_BASE)
 152 #define CONFIG_SYS_CSPR2_EXT    (0xf)
 153 #define CONFIG_SYS_CSPR2        (CSPR_PHYS_ADDR(CONFIG_SYS_CPLD_BASE) \
 154                                 | CSPR_PORT_SIZE_8 \
 155                                 | CSPR_MSEL_GPCM \
 156                                 | CSPR_V)
 157 #define CONFIG_SYS_AMASK2       IFC_AMASK(64*1024)
 158 #define CONFIG_SYS_CSOR2        0x0
 159
 160 /* CPLD Timing parameters for IFC CS2 */
 161 #define CONFIG_SYS_CS2_FTIM0            (FTIM0_GPCM_TACSE(0x0e) | \
 162                                         FTIM0_GPCM_TEADC(0x0e) | \
 163                                         FTIM0_GPCM_TEAHC(0x0e))
 164 #define CONFIG_SYS_CS2_FTIM1            (FTIM1_GPCM_TACO(0x0e) | \
 165                                         FTIM1_GPCM_TRAD(0x1f))
 166 #define CONFIG_SYS_CS2_FTIM2            (FTIM2_GPCM_TCS(0x0e) | \
 167                                         FTIM2_GPCM_TCH(0x8) | \
 168                                         FTIM2_GPCM_TWP(0x1f))
 169 #define CONFIG_SYS_CS2_FTIM3            0x0
 170
 171 /* NAND Flash on IFC */
 172 #define CONFIG_SYS_NAND_BASE            0xff800000
 173 #define CONFIG_SYS_NAND_BASE_PHYS       (0xf00000000ull | CONFIG_SYS_NAND_BASE)
 174
 175 #define CONFIG_SYS_NAND_CSPR_EXT        (0xf)
 176 #define CONFIG_SYS_NAND_CSPR    (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
 177                                 | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
 178                                 | CSPR_MSEL_NAND         /* MSEL = NAND */ \
 179                                 | CSPR_V)
 180 #define CONFIG_SYS_NAND_AMASK   IFC_AMASK(64*1024)
 181
 182 #define CONFIG_SYS_NAND_CSOR    (CSOR_NAND_ECC_ENC_EN   /* ECC on encode */ \
 183                                 | CSOR_NAND_ECC_DEC_EN  /* ECC on decode */ \
 184                                 | CSOR_NAND_ECC_MODE_4  /* 4-bit ECC */     \
 185                                 | CSOR_NAND_RAL_3       /* RAL = 2Byes */   \
 186                                 | CSOR_NAND_PGS_2K      /* Page Size = 2K */\
 187                                 | CSOR_NAND_SPRZ_64     /* Spare size = 64 */\
 188                                 | CSOR_NAND_PB(64))     /*Pages Per Block = 64*/
 189
 190 /* ONFI NAND Flash mode0 Timing Params */
 191 #define CONFIG_SYS_NAND_FTIM0           (FTIM0_NAND_TCCST(0x07) | \
 192                                         FTIM0_NAND_TWP(0x18)    | \
 193                                         FTIM0_NAND_TWCHT(0x07)  | \
 194                                         FTIM0_NAND_TWH(0x0a))
 195 #define CONFIG_SYS_NAND_FTIM1           (FTIM1_NAND_TADLE(0x32) | \
 196                                         FTIM1_NAND_TWBE(0x39)   | \
 197                                         FTIM1_NAND_TRR(0x0e)    | \
 198                                         FTIM1_NAND_TRP(0x18))
 199 #define CONFIG_SYS_NAND_FTIM2           (FTIM2_NAND_TRAD(0x0f)  | \
 200                                         FTIM2_NAND_TREH(0x0a)   | \
 201                                         FTIM2_NAND_TWHRE(0x1e))
 202 #define CONFIG_SYS_NAND_FTIM3           0x0
 203
 204 #define CONFIG_SYS_NAND_DDR_LAW         11
 205 #define CONFIG_SYS_NAND_BASE_LIST       { CONFIG_SYS_NAND_BASE }
 206 #define CONFIG_SYS_MAX_NAND_DEVICE      1
 207
 208 #if defined(CONFIG_MTD_RAW_NAND)
 209 #define CONFIG_SYS_CSPR0_EXT            CONFIG_SYS_NAND_CSPR_EXT
 210 #define CONFIG_SYS_CSPR0                CONFIG_SYS_NAND_CSPR
 211 #define CONFIG_SYS_AMASK0               CONFIG_SYS_NAND_AMASK
 212 #define CONFIG_SYS_CSOR0                CONFIG_SYS_NAND_CSOR
 213 #define CONFIG_SYS_CS0_FTIM0            CONFIG_SYS_NAND_FTIM0
 214 #define CONFIG_SYS_CS0_FTIM1            CONFIG_SYS_NAND_FTIM1
 215 #define CONFIG_SYS_CS0_FTIM2            CONFIG_SYS_NAND_FTIM2
 216 #define CONFIG_SYS_CS0_FTIM3            CONFIG_SYS_NAND_FTIM3
 217 #define CONFIG_SYS_CSPR1_EXT            CONFIG_SYS_NOR0_CSPR_EXT
 218 #define CONFIG_SYS_CSPR1                CONFIG_SYS_NOR0_CSPR
 219 #define CONFIG_SYS_AMASK1               CONFIG_SYS_NOR_AMASK
 220 #define CONFIG_SYS_CSOR1                CONFIG_SYS_NOR_CSOR
 221 #define CONFIG_SYS_CS1_FTIM0            CONFIG_SYS_NOR_FTIM0
 222 #define CONFIG_SYS_CS1_FTIM1            CONFIG_SYS_NOR_FTIM1
 223 #define CONFIG_SYS_CS1_FTIM2            CONFIG_SYS_NOR_FTIM2
 224 #define CONFIG_SYS_CS1_FTIM3            CONFIG_SYS_NOR_FTIM3
 225 #else
 226 #define CONFIG_SYS_CSPR0_EXT            CONFIG_SYS_NOR0_CSPR_EXT
 227 #define CONFIG_SYS_CSPR0                CONFIG_SYS_NOR0_CSPR
 228 #define CONFIG_SYS_AMASK0               CONFIG_SYS_NOR_AMASK
 229 #define CONFIG_SYS_CSOR0                CONFIG_SYS_NOR_CSOR
 230 #define CONFIG_SYS_CS0_FTIM0            CONFIG_SYS_NOR_FTIM0
 231 #define CONFIG_SYS_CS0_FTIM1            CONFIG_SYS_NOR_FTIM1
 232 #define CONFIG_SYS_CS0_FTIM2            CONFIG_SYS_NOR_FTIM2
 233 #define CONFIG_SYS_CS0_FTIM3            CONFIG_SYS_NOR_FTIM3
 234 #define CONFIG_SYS_CSPR1_EXT            CONFIG_SYS_NAND_CSPR_EXT
 235 #define CONFIG_SYS_CSPR1                CONFIG_SYS_NAND_CSPR
 236 #define CONFIG_SYS_AMASK1               CONFIG_SYS_NAND_AMASK
 237 #define CONFIG_SYS_CSOR1                CONFIG_SYS_NAND_CSOR
 238 #define CONFIG_SYS_CS1_FTIM0            CONFIG_SYS_NAND_FTIM0
 239 #define CONFIG_SYS_CS1_FTIM1            CONFIG_SYS_NAND_FTIM1
 240 #define CONFIG_SYS_CS1_FTIM2            CONFIG_SYS_NAND_FTIM2
 241 #define CONFIG_SYS_CS1_FTIM3            CONFIG_SYS_NAND_FTIM3
 242 #endif
 243
 244 #if defined(CONFIG_RAMBOOT_PBL)
 245 #define CONFIG_SYS_RAMBOOT
 246 #endif
 247
 248 #define CONFIG_HWCONFIG
 249
 250 /* define to use L1 as initial stack */
 251 #define CONFIG_L1_INIT_RAM
 252 #define CONFIG_SYS_INIT_RAM_LOCK
 253 #define CONFIG_SYS_INIT_RAM_ADDR        0xfdd00000 /* Initial L1 address */
 254 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH      0xf
 255 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW       0xfe03c000
 256 /* The assembler doesn't like typecast */
 257 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
 258                         ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
 259                         CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
 260 #define CONFIG_SYS_INIT_RAM_SIZE        0x00004000
 261 #define CONFIG_SYS_INIT_SP_OFFSET       (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 262 #define CONFIG_SYS_MONITOR_LEN          (768 * 1024)
 263
 264 /*
 265  * Serial Port
 266  */
 267 #define CONFIG_SYS_NS16550_SERIAL
 268 #define CONFIG_SYS_NS16550_REG_SIZE     1
 269 #define CONFIG_SYS_NS16550_CLK          (get_bus_freq(0)/2)
 270 #define CONFIG_SYS_BAUDRATE_TABLE       \
 271         {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
 272 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500)
 273 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600)
 274 #define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500)
 275 #define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600)
 276
 277 /*
 278  * I2C
 279  */
 280
 281 #define I2C_MUX_PCA_ADDR_PRI    0x77 /* I2C bus multiplexer,primary */
 282 #define I2C_MUX_PCA_ADDR_SEC1   0x75 /* I2C bus multiplexer,secondary 1 */
 283 #define I2C_MUX_PCA_ADDR_SEC2   0x76 /* I2C bus multiplexer,secondary 2 */
 284 #define I2C_MUX_CH_DEFAULT      0x8
 285
 286 #define I2C_MUX_CH_VOL_MONITOR  0xa
 287
 288 /* The lowest and highest voltage allowed for T208xRDB */
 289 #define VDD_MV_MIN                      819
 290 #define VDD_MV_MAX                      1212
 291
 292 /*
 293  * RapidIO
 294  */
 295 #define CONFIG_SYS_SRIO1_MEM_VIRT       0xa0000000
 296 #define CONFIG_SYS_SRIO1_MEM_PHYS       0xc20000000ull
 297 #define CONFIG_SYS_SRIO1_MEM_SIZE       0x10000000 /* 256M */
 298 #define CONFIG_SYS_SRIO2_MEM_VIRT       0xb0000000
 299 #define CONFIG_SYS_SRIO2_MEM_PHYS       0xc30000000ull
 300 #define CONFIG_SYS_SRIO2_MEM_SIZE       0x10000000 /* 256M */
 301 /*
 302  * for slave u-boot IMAGE instored in master memory space,
 303  * PHYS must be aligned based on the SIZE
 304  */
 305 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull
 306 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull
 307 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE     0x100000 /* 1M */
 308 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull
 309 /*
 310  * for slave UCODE and ENV instored in master memory space,
 311  * PHYS must be aligned based on the SIZE
 312  */
 313 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull
 314 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull
 315 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE    0x40000 /* 256K */
 316
 317 /* slave core release by master*/
 318 #define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4
 319 #define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */
 320
 321 /*
 322  * SRIO_PCIE_BOOT - SLAVE
 323  */
 324 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
 325 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000
 326 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \
 327                 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR)
 328 #endif
 329
 330 /*
 331  * eSPI - Enhanced SPI
 332  */
 333
 334 /*
 335  * General PCI
 336  * Memory space is mapped 1-1, but I/O space must start from 0.
 337  */
 338 #define CONFIG_PCIE1            /* PCIE controller 1 */
 339 #define CONFIG_PCIE2            /* PCIE controller 2 */
 340 #define CONFIG_PCIE3            /* PCIE controller 3 */
 341 #define CONFIG_PCIE4            /* PCIE controller 4 */
 342 /* controller 1, direct to uli, tgtid 3, Base address 20000 */
 343 #define CONFIG_SYS_PCIE1_MEM_VIRT       0x80000000
 344 #define CONFIG_SYS_PCIE1_MEM_PHYS       0xc00000000ull
 345 #define CONFIG_SYS_PCIE1_IO_VIRT        0xf8000000
 346 #define CONFIG_SYS_PCIE1_IO_PHYS        0xff8000000ull
 347
 348 /* controller 2, Slot 2, tgtid 2, Base address 201000 */
 349 #define CONFIG_SYS_PCIE2_MEM_VIRT       0xa0000000
 350 #define CONFIG_SYS_PCIE2_MEM_PHYS       0xc20000000ull
 351 #define CONFIG_SYS_PCIE2_IO_VIRT        0xf8010000
 352 #define CONFIG_SYS_PCIE2_IO_PHYS        0xff8010000ull
 353
 354 /* controller 3, Slot 1, tgtid 1, Base address 202000 */
 355 #define CONFIG_SYS_PCIE3_MEM_VIRT       0xb0000000
 356 #define CONFIG_SYS_PCIE3_MEM_PHYS       0xc30000000ull
 357 #define CONFIG_SYS_PCIE3_IO_VIRT        0xf8020000
 358 #define CONFIG_SYS_PCIE3_IO_PHYS        0xff8020000ull
 359
 360 /* controller 4, Base address 203000 */
 361 #define CONFIG_SYS_PCIE4_MEM_VIRT       0xc0000000
 362 #define CONFIG_SYS_PCIE4_MEM_PHYS       0xc40000000ull
 363 #define CONFIG_SYS_PCIE4_IO_PHYS        0xff8030000ull
 364
 365 #ifdef CONFIG_PCI
 366 #define CONFIG_PCI_SCAN_SHOW    /* show pci devices on startup */
 367 #endif
 368
 369 /* Qman/Bman */
 370 #ifndef CONFIG_NOBQFMAN
 371 #define CONFIG_SYS_BMAN_NUM_PORTALS     18
 372 #define CONFIG_SYS_BMAN_MEM_BASE        0xf4000000
 373 #define CONFIG_SYS_BMAN_MEM_PHYS        0xff4000000ull
 374 #define CONFIG_SYS_BMAN_MEM_SIZE        0x02000000
 375 #define CONFIG_SYS_BMAN_SP_CENA_SIZE    0x4000
 376 #define CONFIG_SYS_BMAN_SP_CINH_SIZE    0x1000
 377 #define CONFIG_SYS_BMAN_CENA_BASE       CONFIG_SYS_BMAN_MEM_BASE
 378 #define CONFIG_SYS_BMAN_CENA_SIZE       (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
 379 #define CONFIG_SYS_BMAN_CINH_BASE       (CONFIG_SYS_BMAN_MEM_BASE + \
 380                                         CONFIG_SYS_BMAN_CENA_SIZE)
 381 #define CONFIG_SYS_BMAN_CINH_SIZE       (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
 382 #define CONFIG_SYS_BMAN_SWP_ISDR_REG    0xE08
 383 #define CONFIG_SYS_QMAN_NUM_PORTALS     18
 384 #define CONFIG_SYS_QMAN_MEM_BASE        0xf6000000
 385 #define CONFIG_SYS_QMAN_MEM_PHYS        0xff6000000ull
 386 #define CONFIG_SYS_QMAN_MEM_SIZE        0x02000000
 387 #define CONFIG_SYS_QMAN_SP_CENA_SIZE    0x4000
 388 #define CONFIG_SYS_QMAN_SP_CINH_SIZE    0x1000
 389 #define CONFIG_SYS_QMAN_CENA_BASE       CONFIG_SYS_QMAN_MEM_BASE
 390 #define CONFIG_SYS_QMAN_CENA_SIZE       (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
 391 #define CONFIG_SYS_QMAN_CINH_BASE       (CONFIG_SYS_QMAN_MEM_BASE + \
 392                                         CONFIG_SYS_QMAN_CENA_SIZE)
 393 #define CONFIG_SYS_QMAN_CINH_SIZE       (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
 394 #define CONFIG_SYS_QMAN_SWP_ISDR_REG    0xE08
 395
 396 #define CONFIG_SYS_DPAA_FMAN
 397 #define CONFIG_SYS_DPAA_PME
 398 #define CONFIG_SYS_PMAN
 399 #define CONFIG_SYS_DPAA_DCE
 400 #define CONFIG_SYS_DPAA_RMAN            /* RMan */
 401 #define CONFIG_SYS_INTERLAKEN
 402
 403 #define CONFIG_SYS_FDT_PAD              (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
 404 #endif /* CONFIG_NOBQFMAN */
 405
 406 #ifdef CONFIG_SYS_DPAA_FMAN
 407 #define RGMII_PHY1_ADDR         0x01  /* RealTek RTL8211E */
 408 #define RGMII_PHY2_ADDR         0x02
 409 #define CORTINA_PHY_ADDR1       0x0c  /* Cortina CS4315 */
 410 #define CORTINA_PHY_ADDR2       0x0d
 411 /* Aquantia AQ1202 10G Base-T used by board revisions up to C */
 412 #define FM1_10GEC3_PHY_ADDR     0x00
 413 #define FM1_10GEC4_PHY_ADDR     0x01
 414 /* Aquantia AQR113C 10G Base-T used by board revisions D and up */
 415 #define AQR113C_PHY_ADDR1       0x00
 416 #define AQR113C_PHY_ADDR2       0x08
 417 #endif
 418
 419 /*
 420  * SATA
 421  */
 422 #ifdef CONFIG_FSL_SATA_V2
 423 #define CONFIG_SATA1
 424 #define CONFIG_SYS_SATA1                CONFIG_SYS_MPC85xx_SATA1_ADDR
 425 #define CONFIG_SYS_SATA1_FLAGS          FLAGS_DMA
 426 #define CONFIG_SATA2
 427 #define CONFIG_SYS_SATA2                CONFIG_SYS_MPC85xx_SATA2_ADDR
 428 #define CONFIG_SYS_SATA2_FLAGS          FLAGS_DMA
 429 #define CONFIG_LBA48
 430 #endif
 431
 432 /*
 433  * USB
 434  */
 435 #ifdef CONFIG_USB_EHCI_HCD
 436 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 437 #define CONFIG_HAS_FSL_DR_USB
 438 #endif
 439
 440 /*
 441  * SDHC
 442  */
 443 #ifdef CONFIG_MMC
 444 #define CONFIG_SYS_FSL_ESDHC_ADDR       CONFIG_SYS_MPC85xx_ESDHC_ADDR
 445 #define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT
 446 #endif
 447
 448 /*
 449  * Dynamic MTD Partition support with mtdparts
 450  */
 451
 452 /*
 453  * Environment
 454  */
 455
 456 /*
 457  * Miscellaneous configurable options
 458  */
 459
 460 /*
 461  * For booting Linux, the board info and command line data
 462  * have to be in the first 64 MB of memory, since this is
 463  * the maximum mapped by the Linux kernel during initialization.
 464  */
 465 #define CONFIG_SYS_BOOTMAPSZ    (64 << 20)      /* Initial map for Linux*/
 466 #define CONFIG_SYS_BOOTM_LEN    (64 << 20)      /* Increase max gunzip size */
 467
 468 /*
 469  * Environment Configuration
 470  */
 471 #define CONFIG_ROOTPATH  "/opt/nfsroot"
 472 #define CONFIG_UBOOTPATH "u-boot.bin"   /* U-Boot image on TFTP server */
 473
 474 #define __USB_PHY_TYPE          utmi
 475
 476 #define CONFIG_EXTRA_ENV_SETTINGS                               \
 477         "hwconfig=fsl_ddr:"                                     \
 478         "ctlr_intlv=" __stringify(CTRL_INTLV_PREFERED) ","      \
 479         "bank_intlv=auto;"                                      \
 480         "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\
 481         "netdev=eth0\0"                                         \
 482         "uboot=" __stringify(CONFIG_UBOOTPATH) "\0"             \
 483         "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0"     \
 484         "tftpflash=tftpboot $loadaddr $uboot && "               \
 485         "protect off $ubootaddr +$filesize && "                 \
 486         "erase $ubootaddr +$filesize && "                       \
 487         "cp.b $loadaddr $ubootaddr $filesize && "               \
 488         "protect on $ubootaddr +$filesize && "                  \
 489         "cmp.b $loadaddr $ubootaddr $filesize\0"                \
 490         "consoledev=ttyS0\0"                                    \
 491         "ramdiskaddr=2000000\0"                                 \
 492         "ramdiskfile=t2080rdb/ramdisk.uboot\0"                  \
 493         "fdtaddr=1e00000\0"                                     \
 494         "fdtfile=t2080rdb/t2080rdb.dtb\0"                       \
 495         "bdev=sda3\0"
 496
 497 /*
 498  * For emulation this causes u-boot to jump to the start of the
 499  * proof point app code automatically
 500  */
 501 #define PROOF_POINTS                            \
 502         "setenv bootargs root=/dev/$bdev rw "           \
 503         "console=$consoledev,$baudrate $othbootargs;"   \
 504         "cpu 1 release 0x29000000 - - -;"               \
 505         "cpu 2 release 0x29000000 - - -;"               \
 506         "cpu 3 release 0x29000000 - - -;"               \
 507         "cpu 4 release 0x29000000 - - -;"               \
 508         "cpu 5 release 0x29000000 - - -;"               \
 509         "cpu 6 release 0x29000000 - - -;"               \
 510         "cpu 7 release 0x29000000 - - -;"               \
 511         "go 0x29000000"
 512
 513 #define HVBOOT                          \
 514         "setenv bootargs config-addr=0x60000000; "      \
 515         "bootm 0x01000000 - 0x00f00000"
 516
 517 #define ALU                             \
 518         "setenv bootargs root=/dev/$bdev rw "           \
 519         "console=$consoledev,$baudrate $othbootargs;"   \
 520         "cpu 1 release 0x01000000 - - -;"               \
 521         "cpu 2 release 0x01000000 - - -;"               \
 522         "cpu 3 release 0x01000000 - - -;"               \
 523         "cpu 4 release 0x01000000 - - -;"               \
 524         "cpu 5 release 0x01000000 - - -;"               \
 525         "cpu 6 release 0x01000000 - - -;"               \
 526         "cpu 7 release 0x01000000 - - -;"               \
 527         "go 0x01000000"
 528
 529 #include <asm/fsl_secure_boot.h>
 530
 531 #endif  /* __T2080RDB_H */