include/configs/T208xRDB.h

   1 /* SPDX-License-Identifier: GPL-2.0+ */
   2 /*
   3  * Copyright 2014 Freescale Semiconductor, Inc.
   4  * Copyright 2020 NXP
   5  */
   6
   7 /*
   8  * T2080 RDB/PCIe board configuration file
   9  */
  10
  11 #ifndef __T2080RDB_H
  12 #define __T2080RDB_H
  13
  14 #include <linux/stringify.h>
  15
  16 #define CONFIG_ICS307_REFCLK_HZ 25000000  /* ICS307 ref clk freq */
  17 #define CONFIG_FSL_SATA_V2
  18
  19 /* High Level Configuration Options */
  20 #define CONFIG_SYS_BOOK3E_HV    /* Category E.HV supported */
  21 #define CONFIG_ENABLE_36BIT_PHYS
  22
  23 #define CONFIG_SYS_FSL_CPC      /* Corenet Platform Cache */
  24 #define CONFIG_SYS_NUM_CPC      CONFIG_SYS_NUM_DDR_CTLRS
  25 #define CONFIG_ENV_OVERWRITE
  26
  27 #ifdef CONFIG_RAMBOOT_PBL
  28 #define CONFIG_SYS_FSL_PBL_PBI board/freescale/t208xrdb/t2080_pbi.cfg
  29
  30 #define CONFIG_SPL_FLUSH_IMAGE
  31 #define CONFIG_SPL_PAD_TO               0x40000
  32 #define CONFIG_SPL_MAX_SIZE             0x28000
  33 #define RESET_VECTOR_OFFSET             0x27FFC
  34 #define BOOT_PAGE_OFFSET                0x27000
  35 #ifdef CONFIG_SPL_BUILD
  36 #define CONFIG_SPL_SKIP_RELOCATE
  37 #define CONFIG_SPL_COMMON_INIT_DDR
  38 #define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
  39 #endif
  40
  41 #ifdef CONFIG_MTD_RAW_NAND
  42 #define CONFIG_SYS_NAND_U_BOOT_SIZE     (768 << 10)
  43 #define CONFIG_SYS_NAND_U_BOOT_DST      0x00200000
  44 #define CONFIG_SYS_NAND_U_BOOT_START    0x00200000
  45 #define CONFIG_SYS_NAND_U_BOOT_OFFS     (256 << 10)
  46 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xrdb/t2080_nand_rcw.cfg
  47 #endif
  48
  49 #ifdef CONFIG_SPIFLASH
  50 #define        CONFIG_RESET_VECTOR_ADDRESS             0x200FFC
  51 #define CONFIG_SPL_SPI_FLASH_MINIMAL
  52 #define CONFIG_SYS_SPI_FLASH_U_BOOT_SIZE       (768 << 10)
  53 #define CONFIG_SYS_SPI_FLASH_U_BOOT_DST                (0x00200000)
  54 #define CONFIG_SYS_SPI_FLASH_U_BOOT_START      (0x00200000)
  55 #define CONFIG_SYS_SPI_FLASH_U_BOOT_OFFS       (256 << 10)
  56 #ifndef CONFIG_SPL_BUILD
  57 #define CONFIG_SYS_MPC85XX_NO_RESETVEC
  58 #endif
  59 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xrdb/t2080_spi_rcw.cfg
  60 #endif
  61
  62 #ifdef CONFIG_SDCARD
  63 #define        CONFIG_RESET_VECTOR_ADDRESS             0x200FFC
  64 #define CONFIG_SYS_MMC_U_BOOT_SIZE     (768 << 10)
  65 #define CONFIG_SYS_MMC_U_BOOT_DST      (0x00200000)
  66 #define CONFIG_SYS_MMC_U_BOOT_START    (0x00200000)
  67 #define CONFIG_SYS_MMC_U_BOOT_OFFS     (260 << 10)
  68 #ifndef CONFIG_SPL_BUILD
  69 #define CONFIG_SYS_MPC85XX_NO_RESETVEC
  70 #endif
  71 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xrdb/t2080_sd_rcw.cfg
  72 #endif
  73
  74 #endif /* CONFIG_RAMBOOT_PBL */
  75
  76 #define CONFIG_SRIO_PCIE_BOOT_MASTER
  77 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
  78 /* Set 1M boot space */
  79 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000)
  80 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \
  81                 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR)
  82 #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
  83 #endif
  84
  85 #ifndef CONFIG_RESET_VECTOR_ADDRESS
  86 #define CONFIG_RESET_VECTOR_ADDRESS     0xeffffffc
  87 #endif
  88
  89 /*
  90  * These can be toggled for performance analysis, otherwise use default.
  91  */
  92 #define CONFIG_SYS_CACHE_STASHING
  93 #define CONFIG_BTB              /* toggle branch predition */
  94 #define CONFIG_DDR_ECC
  95 #ifdef CONFIG_DDR_ECC
  96 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
  97 #define CONFIG_MEM_INIT_VALUE           0xdeadbeef
  98 #endif
  99
 100 #if defined(CONFIG_SPIFLASH)
 101 #elif defined(CONFIG_SDCARD)
 102 #define CONFIG_SYS_MMC_ENV_DEV  0
 103 #endif
 104
 105 #ifndef __ASSEMBLY__
 106 unsigned long get_board_sys_clk(void);
 107 unsigned long get_board_ddr_clk(void);
 108 #endif
 109
 110 #define CONFIG_SYS_CLK_FREQ     66660000
 111 #define CONFIG_DDR_CLK_FREQ     133330000
 112
 113 /*
 114  * Config the L3 Cache as L3 SRAM
 115  */
 116 #define CONFIG_SYS_INIT_L3_ADDR         0xFFFC0000
 117 #define CONFIG_SYS_L3_SIZE              (512 << 10)
 118 #define CONFIG_SPL_GD_ADDR              (CONFIG_SYS_INIT_L3_ADDR + 32 * 1024)
 119 #define SPL_ENV_ADDR                    (CONFIG_SPL_GD_ADDR + 4 * 1024)
 120 #define CONFIG_SPL_RELOC_MALLOC_ADDR    (CONFIG_SPL_GD_ADDR + 12 * 1024)
 121 #define CONFIG_SPL_RELOC_MALLOC_SIZE    (50 << 10)
 122 #define CONFIG_SPL_RELOC_STACK          (CONFIG_SPL_GD_ADDR + 64 * 1024)
 123
 124 #define CONFIG_SYS_DCSRBAR      0xf0000000
 125 #define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull
 126
 127 /* EEPROM */
 128 #define CONFIG_ID_EEPROM
 129 #define CONFIG_SYS_I2C_EEPROM_NXID
 130 #define CONFIG_SYS_EEPROM_BUS_NUM       0
 131 #define CONFIG_SYS_I2C_EEPROM_ADDR      0x50
 132 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN  2
 133
 134 /*
 135  * DDR Setup
 136  */
 137 #define CONFIG_VERY_BIG_RAM
 138 #define CONFIG_SYS_DDR_SDRAM_BASE       0x00000000
 139 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE
 140 #define CONFIG_DIMM_SLOTS_PER_CTLR      1
 141 #define CONFIG_CHIP_SELECTS_PER_CTRL    (4 * CONFIG_DIMM_SLOTS_PER_CTLR)
 142 #define CONFIG_DDR_SPD
 143 #define CONFIG_SYS_SPD_BUS_NUM  0
 144 #define CONFIG_SYS_SDRAM_SIZE   2048    /* for fixed parameter use */
 145 #define SPD_EEPROM_ADDRESS1     0x51
 146 #define SPD_EEPROM_ADDRESS2     0x52
 147 #define SPD_EEPROM_ADDRESS      SPD_EEPROM_ADDRESS1
 148 #define CTRL_INTLV_PREFERED     cacheline
 149
 150 /*
 151  * IFC Definitions
 152  */
 153 #define CONFIG_SYS_FLASH_BASE           0xe8000000
 154 #define CONFIG_SYS_FLASH_BASE_PHYS      (0xf00000000ull | CONFIG_SYS_FLASH_BASE)
 155 #define CONFIG_SYS_NOR0_CSPR_EXT        (0xf)
 156 #define CONFIG_SYS_NOR0_CSPR    (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
 157                                 CSPR_PORT_SIZE_16 | \
 158                                 CSPR_MSEL_NOR | \
 159                                 CSPR_V)
 160 #define CONFIG_SYS_NOR_AMASK    IFC_AMASK(128*1024*1024)
 161
 162 /* NOR Flash Timing Params */
 163 #define CONFIG_SYS_NOR_CSOR     CSOR_NAND_TRHZ_80
 164
 165 #define CONFIG_SYS_NOR_FTIM0    (FTIM0_NOR_TACSE(0x4) | \
 166                                 FTIM0_NOR_TEADC(0x5) | \
 167                                 FTIM0_NOR_TEAHC(0x5))
 168 #define CONFIG_SYS_NOR_FTIM1    (FTIM1_NOR_TACO(0x35) | \
 169                                 FTIM1_NOR_TRAD_NOR(0x1A) |\
 170                                 FTIM1_NOR_TSEQRAD_NOR(0x13))
 171 #define CONFIG_SYS_NOR_FTIM2    (FTIM2_NOR_TCS(0x4) | \
 172                                 FTIM2_NOR_TCH(0x4) | \
 173                                 FTIM2_NOR_TWPH(0x0E) | \
 174                                 FTIM2_NOR_TWP(0x1c))
 175 #define CONFIG_SYS_NOR_FTIM3    0x0
 176
 177 #define CONFIG_SYS_FLASH_QUIET_TEST
 178 #define CONFIG_FLASH_SHOW_PROGRESS      45 /* count down from 45/5: 9..1 */
 179
 180 #define CONFIG_SYS_MAX_FLASH_BANKS      1       /* number of banks */
 181 #define CONFIG_SYS_MAX_FLASH_SECT       1024    /* sectors per device */
 182 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000   /* Flash Erase Timeout (ms) */
 183 #define CONFIG_SYS_FLASH_WRITE_TOUT     500     /* Flash Write Timeout (ms) */
 184 #define CONFIG_SYS_FLASH_EMPTY_INFO
 185 #define CONFIG_SYS_FLASH_BANKS_LIST     {CONFIG_SYS_FLASH_BASE_PHYS }
 186
 187 /* CPLD on IFC */
 188 #define CONFIG_SYS_CPLD_BASE    0xffdf0000
 189 #define CONFIG_SYS_CPLD_BASE_PHYS       (0xf00000000ull | CONFIG_SYS_CPLD_BASE)
 190 #define CONFIG_SYS_CSPR2_EXT    (0xf)
 191 #define CONFIG_SYS_CSPR2        (CSPR_PHYS_ADDR(CONFIG_SYS_CPLD_BASE) \
 192                                 | CSPR_PORT_SIZE_8 \
 193                                 | CSPR_MSEL_GPCM \
 194                                 | CSPR_V)
 195 #define CONFIG_SYS_AMASK2       IFC_AMASK(64*1024)
 196 #define CONFIG_SYS_CSOR2        0x0
 197
 198 /* CPLD Timing parameters for IFC CS2 */
 199 #define CONFIG_SYS_CS2_FTIM0            (FTIM0_GPCM_TACSE(0x0e) | \
 200                                         FTIM0_GPCM_TEADC(0x0e) | \
 201                                         FTIM0_GPCM_TEAHC(0x0e))
 202 #define CONFIG_SYS_CS2_FTIM1            (FTIM1_GPCM_TACO(0x0e) | \
 203                                         FTIM1_GPCM_TRAD(0x1f))
 204 #define CONFIG_SYS_CS2_FTIM2            (FTIM2_GPCM_TCS(0x0e) | \
 205                                         FTIM2_GPCM_TCH(0x8) | \
 206                                         FTIM2_GPCM_TWP(0x1f))
 207 #define CONFIG_SYS_CS2_FTIM3            0x0
 208
 209 /* NAND Flash on IFC */
 210 #define CONFIG_NAND_FSL_IFC
 211 #define CONFIG_SYS_NAND_BASE            0xff800000
 212 #define CONFIG_SYS_NAND_BASE_PHYS       (0xf00000000ull | CONFIG_SYS_NAND_BASE)
 213
 214 #define CONFIG_SYS_NAND_CSPR_EXT        (0xf)
 215 #define CONFIG_SYS_NAND_CSPR    (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
 216                                 | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
 217                                 | CSPR_MSEL_NAND         /* MSEL = NAND */ \
 218                                 | CSPR_V)
 219 #define CONFIG_SYS_NAND_AMASK   IFC_AMASK(64*1024)
 220
 221 #define CONFIG_SYS_NAND_CSOR    (CSOR_NAND_ECC_ENC_EN   /* ECC on encode */ \
 222                                 | CSOR_NAND_ECC_DEC_EN  /* ECC on decode */ \
 223                                 | CSOR_NAND_ECC_MODE_4  /* 4-bit ECC */     \
 224                                 | CSOR_NAND_RAL_3       /* RAL = 2Byes */   \
 225                                 | CSOR_NAND_PGS_2K      /* Page Size = 2K */\
 226                                 | CSOR_NAND_SPRZ_64     /* Spare size = 64 */\
 227                                 | CSOR_NAND_PB(64))     /*Pages Per Block = 64*/
 228
 229 #define CONFIG_SYS_NAND_ONFI_DETECTION
 230
 231 /* ONFI NAND Flash mode0 Timing Params */
 232 #define CONFIG_SYS_NAND_FTIM0           (FTIM0_NAND_TCCST(0x07) | \
 233                                         FTIM0_NAND_TWP(0x18)    | \
 234                                         FTIM0_NAND_TWCHT(0x07)  | \
 235                                         FTIM0_NAND_TWH(0x0a))
 236 #define CONFIG_SYS_NAND_FTIM1           (FTIM1_NAND_TADLE(0x32) | \
 237                                         FTIM1_NAND_TWBE(0x39)   | \
 238                                         FTIM1_NAND_TRR(0x0e)    | \
 239                                         FTIM1_NAND_TRP(0x18))
 240 #define CONFIG_SYS_NAND_FTIM2           (FTIM2_NAND_TRAD(0x0f)  | \
 241                                         FTIM2_NAND_TREH(0x0a)   | \
 242                                         FTIM2_NAND_TWHRE(0x1e))
 243 #define CONFIG_SYS_NAND_FTIM3           0x0
 244
 245 #define CONFIG_SYS_NAND_DDR_LAW         11
 246 #define CONFIG_SYS_NAND_BASE_LIST       { CONFIG_SYS_NAND_BASE }
 247 #define CONFIG_SYS_MAX_NAND_DEVICE      1
 248 #define CONFIG_SYS_NAND_BLOCK_SIZE      (512 * 1024)
 249
 250 #if defined(CONFIG_MTD_RAW_NAND)
 251 #define CONFIG_SYS_CSPR0_EXT            CONFIG_SYS_NAND_CSPR_EXT
 252 #define CONFIG_SYS_CSPR0                CONFIG_SYS_NAND_CSPR
 253 #define CONFIG_SYS_AMASK0               CONFIG_SYS_NAND_AMASK
 254 #define CONFIG_SYS_CSOR0                CONFIG_SYS_NAND_CSOR
 255 #define CONFIG_SYS_CS0_FTIM0            CONFIG_SYS_NAND_FTIM0
 256 #define CONFIG_SYS_CS0_FTIM1            CONFIG_SYS_NAND_FTIM1
 257 #define CONFIG_SYS_CS0_FTIM2            CONFIG_SYS_NAND_FTIM2
 258 #define CONFIG_SYS_CS0_FTIM3            CONFIG_SYS_NAND_FTIM3
 259 #define CONFIG_SYS_CSPR1_EXT            CONFIG_SYS_NOR0_CSPR_EXT
 260 #define CONFIG_SYS_CSPR1                CONFIG_SYS_NOR0_CSPR
 261 #define CONFIG_SYS_AMASK1               CONFIG_SYS_NOR_AMASK
 262 #define CONFIG_SYS_CSOR1                CONFIG_SYS_NOR_CSOR
 263 #define CONFIG_SYS_CS1_FTIM0            CONFIG_SYS_NOR_FTIM0
 264 #define CONFIG_SYS_CS1_FTIM1            CONFIG_SYS_NOR_FTIM1
 265 #define CONFIG_SYS_CS1_FTIM2            CONFIG_SYS_NOR_FTIM2
 266 #define CONFIG_SYS_CS1_FTIM3            CONFIG_SYS_NOR_FTIM3
 267 #else
 268 #define CONFIG_SYS_CSPR0_EXT            CONFIG_SYS_NOR0_CSPR_EXT
 269 #define CONFIG_SYS_CSPR0                CONFIG_SYS_NOR0_CSPR
 270 #define CONFIG_SYS_AMASK0               CONFIG_SYS_NOR_AMASK
 271 #define CONFIG_SYS_CSOR0                CONFIG_SYS_NOR_CSOR
 272 #define CONFIG_SYS_CS0_FTIM0            CONFIG_SYS_NOR_FTIM0
 273 #define CONFIG_SYS_CS0_FTIM1            CONFIG_SYS_NOR_FTIM1
 274 #define CONFIG_SYS_CS0_FTIM2            CONFIG_SYS_NOR_FTIM2
 275 #define CONFIG_SYS_CS0_FTIM3            CONFIG_SYS_NOR_FTIM3
 276 #define CONFIG_SYS_CSPR1_EXT            CONFIG_SYS_NAND_CSPR_EXT
 277 #define CONFIG_SYS_CSPR1                CONFIG_SYS_NAND_CSPR
 278 #define CONFIG_SYS_AMASK1               CONFIG_SYS_NAND_AMASK
 279 #define CONFIG_SYS_CSOR1                CONFIG_SYS_NAND_CSOR
 280 #define CONFIG_SYS_CS1_FTIM0            CONFIG_SYS_NAND_FTIM0
 281 #define CONFIG_SYS_CS1_FTIM1            CONFIG_SYS_NAND_FTIM1
 282 #define CONFIG_SYS_CS1_FTIM2            CONFIG_SYS_NAND_FTIM2
 283 #define CONFIG_SYS_CS1_FTIM3            CONFIG_SYS_NAND_FTIM3
 284 #endif
 285
 286 #if defined(CONFIG_RAMBOOT_PBL)
 287 #define CONFIG_SYS_RAMBOOT
 288 #endif
 289
 290 #ifdef CONFIG_SPL_BUILD
 291 #define CONFIG_SYS_MONITOR_BASE  CONFIG_SPL_TEXT_BASE
 292 #else
 293 #define CONFIG_SYS_MONITOR_BASE  CONFIG_SYS_TEXT_BASE /* start of monitor */
 294 #endif
 295
 296 #define CONFIG_HWCONFIG
 297
 298 /* define to use L1 as initial stack */
 299 #define CONFIG_L1_INIT_RAM
 300 #define CONFIG_SYS_INIT_RAM_LOCK
 301 #define CONFIG_SYS_INIT_RAM_ADDR        0xfdd00000 /* Initial L1 address */
 302 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH      0xf
 303 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW       0xfe03c000
 304 /* The assembler doesn't like typecast */
 305 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
 306                         ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
 307                         CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
 308 #define CONFIG_SYS_INIT_RAM_SIZE        0x00004000
 309 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - \
 310                                                 GENERATED_GBL_DATA_SIZE)
 311 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 312 #define CONFIG_SYS_MONITOR_LEN          (768 * 1024)
 313 #define CONFIG_SYS_MALLOC_LEN           (4 * 1024 * 1024)
 314
 315 /*
 316  * Serial Port
 317  */
 318 #define CONFIG_SYS_NS16550_SERIAL
 319 #define CONFIG_SYS_NS16550_REG_SIZE     1
 320 #define CONFIG_SYS_NS16550_CLK          (get_bus_freq(0)/2)
 321 #define CONFIG_SYS_BAUDRATE_TABLE       \
 322         {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
 323 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500)
 324 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600)
 325 #define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500)
 326 #define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600)
 327
 328 /*
 329  * I2C
 330  */
 331 #ifndef CONFIG_DM_I2C
 332 #define CONFIG_SYS_I2C
 333 #define CONFIG_SYS_FSL_I2C_SLAVE   0x7F
 334 #define CONFIG_SYS_FSL_I2C2_SLAVE  0x7F
 335 #define CONFIG_SYS_FSL_I2C3_SLAVE  0x7F
 336 #define CONFIG_SYS_FSL_I2C4_SLAVE  0x7F
 337 #define CONFIG_SYS_FSL_I2C_OFFSET  0x118000
 338 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x118100
 339 #define CONFIG_SYS_FSL_I2C3_OFFSET 0x119000
 340 #define CONFIG_SYS_FSL_I2C4_OFFSET 0x119100
 341 #define CONFIG_SYS_FSL_I2C_SPEED   100000
 342 #define CONFIG_SYS_FSL_I2C2_SPEED  100000
 343 #define CONFIG_SYS_FSL_I2C3_SPEED  100000
 344 #define CONFIG_SYS_FSL_I2C4_SPEED  100000
 345 #else
 346 #define CONFIG_I2C_SET_DEFAULT_BUS_NUM
 347 #define CONFIG_I2C_DEFAULT_BUS_NUMBER   0
 348 #endif
 349
 350 #define CONFIG_SYS_I2C_FSL
 351
 352 #define I2C_MUX_PCA_ADDR_PRI    0x77 /* I2C bus multiplexer,primary */
 353 #define I2C_MUX_PCA_ADDR_SEC1   0x75 /* I2C bus multiplexer,secondary 1 */
 354 #define I2C_MUX_PCA_ADDR_SEC2   0x76 /* I2C bus multiplexer,secondary 2 */
 355 #define I2C_MUX_CH_DEFAULT      0x8
 356
 357 #define I2C_MUX_CH_VOL_MONITOR  0xa
 358
 359 #define CONFIG_VID_FLS_ENV              "t208xrdb_vdd_mv"
 360 #ifndef CONFIG_SPL_BUILD
 361 #define CONFIG_VID
 362 #endif
 363 #define CONFIG_VOL_MONITOR_IR36021_SET
 364 #define CONFIG_VOL_MONITOR_IR36021_READ
 365 /* The lowest and highest voltage allowed for T208xRDB */
 366 #define VDD_MV_MIN                      819
 367 #define VDD_MV_MAX                      1212
 368
 369 /*
 370  * RapidIO
 371  */
 372 #define CONFIG_SYS_SRIO1_MEM_VIRT       0xa0000000
 373 #define CONFIG_SYS_SRIO1_MEM_PHYS       0xc20000000ull
 374 #define CONFIG_SYS_SRIO1_MEM_SIZE       0x10000000 /* 256M */
 375 #define CONFIG_SYS_SRIO2_MEM_VIRT       0xb0000000
 376 #define CONFIG_SYS_SRIO2_MEM_PHYS       0xc30000000ull
 377 #define CONFIG_SYS_SRIO2_MEM_SIZE       0x10000000 /* 256M */
 378 /*
 379  * for slave u-boot IMAGE instored in master memory space,
 380  * PHYS must be aligned based on the SIZE
 381  */
 382 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull
 383 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull
 384 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE     0x100000 /* 1M */
 385 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull
 386 /*
 387  * for slave UCODE and ENV instored in master memory space,
 388  * PHYS must be aligned based on the SIZE
 389  */
 390 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull
 391 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull
 392 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE    0x40000 /* 256K */
 393
 394 /* slave core release by master*/
 395 #define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4
 396 #define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */
 397
 398 /*
 399  * SRIO_PCIE_BOOT - SLAVE
 400  */
 401 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
 402 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000
 403 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \
 404                 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR)
 405 #endif
 406
 407 /*
 408  * eSPI - Enhanced SPI
 409  */
 410
 411 /*
 412  * General PCI
 413  * Memory space is mapped 1-1, but I/O space must start from 0.
 414  */
 415 #define CONFIG_PCIE1            /* PCIE controller 1 */
 416 #define CONFIG_PCIE2            /* PCIE controller 2 */
 417 #define CONFIG_PCIE3            /* PCIE controller 3 */
 418 #define CONFIG_PCIE4            /* PCIE controller 4 */
 419 #define CONFIG_SYS_PCI_64BIT    /* enable 64-bit PCI resources */
 420 /* controller 1, direct to uli, tgtid 3, Base address 20000 */
 421 #define CONFIG_SYS_PCIE1_MEM_VIRT       0x80000000
 422 #define CONFIG_SYS_PCIE1_MEM_PHYS       0xc00000000ull
 423 #define CONFIG_SYS_PCIE1_IO_VIRT        0xf8000000
 424 #define CONFIG_SYS_PCIE1_IO_PHYS        0xff8000000ull
 425
 426 /* controller 2, Slot 2, tgtid 2, Base address 201000 */
 427 #define CONFIG_SYS_PCIE2_MEM_VIRT       0xa0000000
 428 #define CONFIG_SYS_PCIE2_MEM_PHYS       0xc20000000ull
 429 #define CONFIG_SYS_PCIE2_IO_VIRT        0xf8010000
 430 #define CONFIG_SYS_PCIE2_IO_PHYS        0xff8010000ull
 431
 432 /* controller 3, Slot 1, tgtid 1, Base address 202000 */
 433 #define CONFIG_SYS_PCIE3_MEM_VIRT       0xb0000000
 434 #define CONFIG_SYS_PCIE3_MEM_PHYS       0xc30000000ull
 435 #define CONFIG_SYS_PCIE3_IO_VIRT        0xf8020000
 436 #define CONFIG_SYS_PCIE3_IO_PHYS        0xff8020000ull
 437
 438 /* controller 4, Base address 203000 */
 439 #define CONFIG_SYS_PCIE4_MEM_VIRT       0xc0000000
 440 #define CONFIG_SYS_PCIE4_MEM_PHYS       0xc40000000ull
 441 #define CONFIG_SYS_PCIE4_IO_PHYS        0xff8030000ull
 442
 443 #ifdef CONFIG_PCI
 444 #if !defined(CONFIG_DM_PCI)
 445 #define CONFIG_FSL_PCI_INIT     /* Use common FSL init code */
 446 #define CONFIG_SYS_PCIE1_MEM_BUS        0xe0000000
 447 #define CONFIG_SYS_PCIE1_MEM_SIZE       0x20000000      /* 512M */
 448 #define CONFIG_SYS_PCIE1_IO_BUS         0x00000000
 449 #define CONFIG_SYS_PCIE1_IO_SIZE        0x00010000      /* 64k */
 450 #define CONFIG_SYS_PCIE2_MEM_BUS        0xe0000000
 451 #define CONFIG_SYS_PCIE2_MEM_SIZE       0x10000000 /* 256M */
 452 #define CONFIG_SYS_PCIE2_IO_BUS         0x00000000
 453 #define CONFIG_SYS_PCIE2_IO_SIZE        0x00010000      /* 64k */
 454 #define CONFIG_SYS_PCIE3_MEM_BUS        0xe0000000
 455 #define CONFIG_SYS_PCIE3_MEM_SIZE       0x10000000      /* 256M */
 456 #define CONFIG_SYS_PCIE3_IO_BUS         0x00000000
 457 #define CONFIG_SYS_PCIE3_IO_SIZE        0x00010000      /* 64k */
 458 #define CONFIG_SYS_PCIE4_MEM_BUS        0xe0000000
 459 #define CONFIG_SYS_PCIE4_MEM_SIZE       0x10000000      /* 256M */
 460 #define CONFIG_SYS_PCIE4_IO_BUS         0x00000000
 461 #define CONFIG_SYS_PCIE4_IO_SIZE        0x00010000      /* 64k */
 462 #define CONFIG_PCI_INDIRECT_BRIDGE
 463 #endif
 464 #define CONFIG_PCI_SCAN_SHOW    /* show pci devices on startup */
 465 #endif
 466
 467 /* Qman/Bman */
 468 #ifndef CONFIG_NOBQFMAN
 469 #define CONFIG_SYS_BMAN_NUM_PORTALS     18
 470 #define CONFIG_SYS_BMAN_MEM_BASE        0xf4000000
 471 #define CONFIG_SYS_BMAN_MEM_PHYS        0xff4000000ull
 472 #define CONFIG_SYS_BMAN_MEM_SIZE        0x02000000
 473 #define CONFIG_SYS_BMAN_SP_CENA_SIZE    0x4000
 474 #define CONFIG_SYS_BMAN_SP_CINH_SIZE    0x1000
 475 #define CONFIG_SYS_BMAN_CENA_BASE       CONFIG_SYS_BMAN_MEM_BASE
 476 #define CONFIG_SYS_BMAN_CENA_SIZE       (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
 477 #define CONFIG_SYS_BMAN_CINH_BASE       (CONFIG_SYS_BMAN_MEM_BASE + \
 478                                         CONFIG_SYS_BMAN_CENA_SIZE)
 479 #define CONFIG_SYS_BMAN_CINH_SIZE       (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
 480 #define CONFIG_SYS_BMAN_SWP_ISDR_REG    0xE08
 481 #define CONFIG_SYS_QMAN_NUM_PORTALS     18
 482 #define CONFIG_SYS_QMAN_MEM_BASE        0xf6000000
 483 #define CONFIG_SYS_QMAN_MEM_PHYS        0xff6000000ull
 484 #define CONFIG_SYS_QMAN_MEM_SIZE        0x02000000
 485 #define CONFIG_SYS_QMAN_SP_CENA_SIZE    0x4000
 486 #define CONFIG_SYS_QMAN_SP_CINH_SIZE    0x1000
 487 #define CONFIG_SYS_QMAN_CENA_BASE       CONFIG_SYS_QMAN_MEM_BASE
 488 #define CONFIG_SYS_QMAN_CENA_SIZE       (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
 489 #define CONFIG_SYS_QMAN_CINH_BASE       (CONFIG_SYS_QMAN_MEM_BASE + \
 490                                         CONFIG_SYS_QMAN_CENA_SIZE)
 491 #define CONFIG_SYS_QMAN_CINH_SIZE       (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
 492 #define CONFIG_SYS_QMAN_SWP_ISDR_REG    0xE08
 493
 494 #define CONFIG_SYS_DPAA_FMAN
 495 #define CONFIG_SYS_DPAA_PME
 496 #define CONFIG_SYS_PMAN
 497 #define CONFIG_SYS_DPAA_DCE
 498 #define CONFIG_SYS_DPAA_RMAN            /* RMan */
 499 #define CONFIG_SYS_INTERLAKEN
 500
 501 /* Default address of microcode for the Linux Fman driver */
 502 #if defined(CONFIG_SPIFLASH)
 503 /*
 504  * env is stored at 0x100000, sector size is 0x10000, ucode is stored after
 505  * env, so we got 0x110000.
 506  */
 507 #define CONFIG_SYS_FMAN_FW_ADDR         0x110000
 508 #define CONFIG_CORTINA_FW_ADDR          0x120000
 509
 510 #elif defined(CONFIG_SDCARD)
 511 /*
 512  * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
 513  * about 1MB (2048 blocks), Env is stored after the image, and the env size is
 514  * 0x2000 (16 blocks), 8 + 2048 + 16 = 2072, enlarge it to 2080.
 515  */
 516 #define CONFIG_SYS_FMAN_FW_ADDR         (512 * 0x820)
 517 #define CONFIG_CORTINA_FW_ADDR          (512 * 0x8a0)
 518
 519 #elif defined(CONFIG_MTD_RAW_NAND)
 520 #define CONFIG_SYS_FMAN_FW_ADDR         (3 * CONFIG_SYS_NAND_BLOCK_SIZE)
 521 #define CONFIG_CORTINA_FW_ADDR          (4 * CONFIG_SYS_NAND_BLOCK_SIZE)
 522 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
 523 /*
 524  * Slave has no ucode locally, it can fetch this from remote. When implementing
 525  * in two corenet boards, slave's ucode could be stored in master's memory
 526  * space, the address can be mapped from slave TLB->slave LAW->
 527  * slave SRIO or PCIE outbound window->master inbound window->
 528  * master LAW->the ucode address in master's memory space.
 529  */
 530 #define CONFIG_SYS_FMAN_FW_ADDR         0xFFE00000
 531 #define CONFIG_CORTINA_FW_ADDR          0xFFE10000
 532 #else
 533 #define CONFIG_SYS_FMAN_FW_ADDR         0xEFF00000
 534 #define CONFIG_CORTINA_FW_ADDR          0xEFE00000
 535 #endif
 536 #define CONFIG_SYS_QE_FMAN_FW_LENGTH    0x10000
 537 #define CONFIG_SYS_FDT_PAD              (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
 538 #endif /* CONFIG_NOBQFMAN */
 539
 540 #ifdef CONFIG_SYS_DPAA_FMAN
 541 #define CONFIG_CORTINA_FW_LENGTH        0x40000
 542 #define RGMII_PHY1_ADDR         0x01  /* RealTek RTL8211E */
 543 #define RGMII_PHY2_ADDR         0x02
 544 #define CORTINA_PHY_ADDR1       0x0c  /* Cortina CS4315 */
 545 #define CORTINA_PHY_ADDR2       0x0d
 546 #define FM1_10GEC3_PHY_ADDR     0x00  /* Aquantia AQ1202 10G Base-T */
 547 #define FM1_10GEC4_PHY_ADDR     0x01
 548 #endif
 549
 550 #ifdef CONFIG_FMAN_ENET
 551 #define CONFIG_ETHPRIME         "FM1@DTSEC3"
 552 #endif
 553
 554 /*
 555  * SATA
 556  */
 557 #ifdef CONFIG_FSL_SATA_V2
 558 #define CONFIG_SYS_SATA_MAX_DEVICE      2
 559 #define CONFIG_SATA1
 560 #define CONFIG_SYS_SATA1                CONFIG_SYS_MPC85xx_SATA1_ADDR
 561 #define CONFIG_SYS_SATA1_FLAGS          FLAGS_DMA
 562 #define CONFIG_SATA2
 563 #define CONFIG_SYS_SATA2                CONFIG_SYS_MPC85xx_SATA2_ADDR
 564 #define CONFIG_SYS_SATA2_FLAGS          FLAGS_DMA
 565 #define CONFIG_LBA48
 566 #endif
 567
 568 /*
 569  * USB
 570  */
 571 #ifdef CONFIG_USB_EHCI_HCD
 572 #define CONFIG_USB_EHCI_FSL
 573 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 574 #define CONFIG_HAS_FSL_DR_USB
 575 #endif
 576
 577 /*
 578  * SDHC
 579  */
 580 #ifdef CONFIG_MMC
 581 #define CONFIG_SYS_FSL_ESDHC_ADDR       CONFIG_SYS_MPC85xx_ESDHC_ADDR
 582 #define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT
 583 #define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
 584 #endif
 585
 586 /*
 587  * Dynamic MTD Partition support with mtdparts
 588  */
 589
 590 /*
 591  * Environment
 592  */
 593
 594 /*
 595  * Miscellaneous configurable options
 596  */
 597 #define CONFIG_SYS_LOAD_ADDR    0x2000000 /* default load address */
 598
 599 /*
 600  * For booting Linux, the board info and command line data
 601  * have to be in the first 64 MB of memory, since this is
 602  * the maximum mapped by the Linux kernel during initialization.
 603  */
 604 #define CONFIG_SYS_BOOTMAPSZ    (64 << 20)      /* Initial map for Linux*/
 605 #define CONFIG_SYS_BOOTM_LEN    (64 << 20)      /* Increase max gunzip size */
 606
 607 #ifdef CONFIG_CMD_KGDB
 608 #define CONFIG_KGDB_BAUDRATE    230400  /* speed to run kgdb serial port */
 609 #define CONFIG_KGDB_SER_INDEX   2       /* which serial port to use */
 610 #endif
 611
 612 /*
 613  * Environment Configuration
 614  */
 615 #define CONFIG_ROOTPATH  "/opt/nfsroot"
 616 #define CONFIG_BOOTFILE  "uImage"
 617 #define CONFIG_UBOOTPATH "u-boot.bin"   /* U-Boot image on TFTP server */
 618
 619 /* default location for tftp and bootm */
 620 #define CONFIG_LOADADDR         1000000
 621 #define __USB_PHY_TYPE          utmi
 622
 623 #define CONFIG_EXTRA_ENV_SETTINGS                               \
 624         "hwconfig=fsl_ddr:"                                     \
 625         "ctlr_intlv=" __stringify(CTRL_INTLV_PREFERED) ","      \
 626         "bank_intlv=auto;"                                      \
 627         "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\
 628         "netdev=eth0\0"                                         \
 629         "uboot=" __stringify(CONFIG_UBOOTPATH) "\0"             \
 630         "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0"     \
 631         "tftpflash=tftpboot $loadaddr $uboot && "               \
 632         "protect off $ubootaddr +$filesize && "                 \
 633         "erase $ubootaddr +$filesize && "                       \
 634         "cp.b $loadaddr $ubootaddr $filesize && "               \
 635         "protect on $ubootaddr +$filesize && "                  \
 636         "cmp.b $loadaddr $ubootaddr $filesize\0"                \
 637         "consoledev=ttyS0\0"                                    \
 638         "ramdiskaddr=2000000\0"                                 \
 639         "ramdiskfile=t2080rdb/ramdisk.uboot\0"                  \
 640         "fdtaddr=1e00000\0"                                     \
 641         "fdtfile=t2080rdb/t2080rdb.dtb\0"                       \
 642         "bdev=sda3\0"
 643
 644 /*
 645  * For emulation this causes u-boot to jump to the start of the
 646  * proof point app code automatically
 647  */
 648 #define CONFIG_PROOF_POINTS                             \
 649         "setenv bootargs root=/dev/$bdev rw "           \
 650         "console=$consoledev,$baudrate $othbootargs;"   \
 651         "cpu 1 release 0x29000000 - - -;"               \
 652         "cpu 2 release 0x29000000 - - -;"               \
 653         "cpu 3 release 0x29000000 - - -;"               \
 654         "cpu 4 release 0x29000000 - - -;"               \
 655         "cpu 5 release 0x29000000 - - -;"               \
 656         "cpu 6 release 0x29000000 - - -;"               \
 657         "cpu 7 release 0x29000000 - - -;"               \
 658         "go 0x29000000"
 659
 660 #define CONFIG_HVBOOT                           \
 661         "setenv bootargs config-addr=0x60000000; "      \
 662         "bootm 0x01000000 - 0x00f00000"
 663
 664 #define CONFIG_ALU                              \
 665         "setenv bootargs root=/dev/$bdev rw "           \
 666         "console=$consoledev,$baudrate $othbootargs;"   \
 667         "cpu 1 release 0x01000000 - - -;"               \
 668         "cpu 2 release 0x01000000 - - -;"               \
 669         "cpu 3 release 0x01000000 - - -;"               \
 670         "cpu 4 release 0x01000000 - - -;"               \
 671         "cpu 5 release 0x01000000 - - -;"               \
 672         "cpu 6 release 0x01000000 - - -;"               \
 673         "cpu 7 release 0x01000000 - - -;"               \
 674         "go 0x01000000"
 675
 676 #define CONFIG_LINUX                            \
 677         "setenv bootargs root=/dev/ram rw "             \
 678         "console=$consoledev,$baudrate $othbootargs;"   \
 679         "setenv ramdiskaddr 0x02000000;"                \
 680         "setenv fdtaddr 0x00c00000;"                    \
 681         "setenv loadaddr 0x1000000;"                    \
 682         "bootm $loadaddr $ramdiskaddr $fdtaddr"
 683
 684 #define CONFIG_HDBOOT                                   \
 685         "setenv bootargs root=/dev/$bdev rw "           \
 686         "console=$consoledev,$baudrate $othbootargs;"   \
 687         "tftp $loadaddr $bootfile;"                     \
 688         "tftp $fdtaddr $fdtfile;"                       \
 689         "bootm $loadaddr - $fdtaddr"
 690
 691 #define CONFIG_NFSBOOTCOMMAND                   \
 692         "setenv bootargs root=/dev/nfs rw "     \
 693         "nfsroot=$serverip:$rootpath "          \
 694         "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
 695         "console=$consoledev,$baudrate $othbootargs;"   \
 696         "tftp $loadaddr $bootfile;"             \
 697         "tftp $fdtaddr $fdtfile;"               \
 698         "bootm $loadaddr - $fdtaddr"
 699
 700 #define CONFIG_RAMBOOTCOMMAND                           \
 701         "setenv bootargs root=/dev/ram rw "             \
 702         "console=$consoledev,$baudrate $othbootargs;"   \
 703         "tftp $ramdiskaddr $ramdiskfile;"               \
 704         "tftp $loadaddr $bootfile;"                     \
 705         "tftp $fdtaddr $fdtfile;"                       \
 706         "bootm $loadaddr $ramdiskaddr $fdtaddr"
 707
 708 #define CONFIG_BOOTCOMMAND              CONFIG_LINUX
 709
 710 #include <asm/fsl_secure_boot.h>
 711
 712 #endif  /* __T2080RDB_H */