include/configs/T208xRDB.h

   1 /* SPDX-License-Identifier: GPL-2.0+ */
   2 /*
   3  * Copyright 2014 Freescale Semiconductor, Inc.
   4  * Copyright 2020-2021 NXP
   5  */
   6
   7 /*
   8  * T2080 RDB/PCIe board configuration file
   9  */
  10
  11 #ifndef __T2080RDB_H
  12 #define __T2080RDB_H
  13
  14 #include <linux/stringify.h>
  15
  16 #define CONFIG_ICS307_REFCLK_HZ 25000000  /* ICS307 ref clk freq */
  17 #define CONFIG_FSL_SATA_V2
  18
  19 /* High Level Configuration Options */
  20 #define CONFIG_SYS_BOOK3E_HV    /* Category E.HV supported */
  21 #define CONFIG_ENABLE_36BIT_PHYS
  22
  23 #define CONFIG_SYS_FSL_CPC      /* Corenet Platform Cache */
  24 #define CONFIG_SYS_NUM_CPC      CONFIG_SYS_NUM_DDR_CTLRS
  25
  26 #ifdef CONFIG_RAMBOOT_PBL
  27 #define RESET_VECTOR_OFFSET             0x27FFC
  28 #define BOOT_PAGE_OFFSET                0x27000
  29
  30 #ifdef CONFIG_MTD_RAW_NAND
  31 #define CONFIG_SYS_NAND_U_BOOT_SIZE     (768 << 10)
  32 #define CONFIG_SYS_NAND_U_BOOT_DST      0x00200000
  33 #define CONFIG_SYS_NAND_U_BOOT_START    0x00200000
  34 #ifndef CONFIG_MPC85XX_HAVE_RESET_VECTOR
  35 #define CONFIG_SYS_MPC85XX_NO_RESETVEC
  36 #endif
  37 #endif
  38
  39 #ifdef CONFIG_SPIFLASH
  40 #define        CONFIG_RESET_VECTOR_ADDRESS             0x200FFC
  41 #define CONFIG_SPL_SPI_FLASH_MINIMAL
  42 #define CONFIG_SYS_SPI_FLASH_U_BOOT_SIZE       (768 << 10)
  43 #define CONFIG_SYS_SPI_FLASH_U_BOOT_DST                (0x00200000)
  44 #define CONFIG_SYS_SPI_FLASH_U_BOOT_START      (0x00200000)
  45 #define CONFIG_SYS_SPI_FLASH_U_BOOT_OFFS       (256 << 10)
  46 #ifndef CONFIG_SPL_BUILD
  47 #define CONFIG_SYS_MPC85XX_NO_RESETVEC
  48 #endif
  49 #endif
  50
  51 #ifdef CONFIG_SDCARD
  52 #define        CONFIG_RESET_VECTOR_ADDRESS             0x200FFC
  53 #define CONFIG_SYS_MMC_U_BOOT_SIZE     (768 << 10)
  54 #define CONFIG_SYS_MMC_U_BOOT_DST      (0x00200000)
  55 #define CONFIG_SYS_MMC_U_BOOT_START    (0x00200000)
  56 #define CONFIG_SYS_MMC_U_BOOT_OFFS     (260 << 10)
  57 #ifndef CONFIG_SPL_BUILD
  58 #define CONFIG_SYS_MPC85XX_NO_RESETVEC
  59 #endif
  60 #endif
  61
  62 #endif /* CONFIG_RAMBOOT_PBL */
  63
  64 #define CONFIG_SRIO_PCIE_BOOT_MASTER
  65 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
  66 /* Set 1M boot space */
  67 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000)
  68 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \
  69                 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR)
  70 #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
  71 #endif
  72
  73 #ifndef CONFIG_RESET_VECTOR_ADDRESS
  74 #define CONFIG_RESET_VECTOR_ADDRESS     0xeffffffc
  75 #endif
  76
  77 /*
  78  * These can be toggled for performance analysis, otherwise use default.
  79  */
  80 #define CONFIG_SYS_CACHE_STASHING
  81 #ifdef CONFIG_DDR_ECC
  82 #define CONFIG_MEM_INIT_VALUE           0xdeadbeef
  83 #endif
  84
  85 /*
  86  * Config the L3 Cache as L3 SRAM
  87  */
  88 #define CONFIG_SYS_INIT_L3_ADDR         0xFFFC0000
  89 #define CONFIG_SYS_L3_SIZE              (512 << 10)
  90 #define CONFIG_SPL_GD_ADDR              (CONFIG_SYS_INIT_L3_ADDR + 32 * 1024)
  91 #define SPL_ENV_ADDR                    (CONFIG_SPL_GD_ADDR + 4 * 1024)
  92 #define CONFIG_SPL_RELOC_MALLOC_ADDR    (CONFIG_SPL_GD_ADDR + 12 * 1024)
  93 #define CONFIG_SPL_RELOC_MALLOC_SIZE    (50 << 10)
  94 #define CONFIG_SPL_RELOC_STACK          (CONFIG_SPL_GD_ADDR + 64 * 1024)
  95
  96 #define CONFIG_SYS_DCSRBAR      0xf0000000
  97 #define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull
  98
  99 /* EEPROM */
 100 #define CONFIG_SYS_I2C_EEPROM_NXID
 101 #define CONFIG_SYS_EEPROM_BUS_NUM       0
 102
 103 /*
 104  * DDR Setup
 105  */
 106 #define CONFIG_VERY_BIG_RAM
 107 #define CONFIG_SYS_DDR_SDRAM_BASE       0x00000000
 108 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE
 109 #define CONFIG_SYS_SPD_BUS_NUM  0
 110 #define CONFIG_SYS_SDRAM_SIZE   2048    /* for fixed parameter use */
 111 #define SPD_EEPROM_ADDRESS1     0x51
 112 #define SPD_EEPROM_ADDRESS2     0x52
 113 #define SPD_EEPROM_ADDRESS      SPD_EEPROM_ADDRESS1
 114 #define CTRL_INTLV_PREFERED     cacheline
 115
 116 /*
 117  * IFC Definitions
 118  */
 119 #define CONFIG_SYS_FLASH_BASE           0xe8000000
 120 #define CONFIG_SYS_FLASH_BASE_PHYS      (0xf00000000ull | CONFIG_SYS_FLASH_BASE)
 121 #define CONFIG_SYS_NOR0_CSPR_EXT        (0xf)
 122 #define CONFIG_SYS_NOR0_CSPR    (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
 123                                 CSPR_PORT_SIZE_16 | \
 124                                 CSPR_MSEL_NOR | \
 125                                 CSPR_V)
 126 #define CONFIG_SYS_NOR_AMASK    IFC_AMASK(128*1024*1024)
 127
 128 /* NOR Flash Timing Params */
 129 #define CONFIG_SYS_NOR_CSOR     CSOR_NAND_TRHZ_80
 130
 131 #define CONFIG_SYS_NOR_FTIM0    (FTIM0_NOR_TACSE(0x4) | \
 132                                 FTIM0_NOR_TEADC(0x5) | \
 133                                 FTIM0_NOR_TEAHC(0x5))
 134 #define CONFIG_SYS_NOR_FTIM1    (FTIM1_NOR_TACO(0x35) | \
 135                                 FTIM1_NOR_TRAD_NOR(0x1A) |\
 136                                 FTIM1_NOR_TSEQRAD_NOR(0x13))
 137 #define CONFIG_SYS_NOR_FTIM2    (FTIM2_NOR_TCS(0x4) | \
 138                                 FTIM2_NOR_TCH(0x4) | \
 139                                 FTIM2_NOR_TWPH(0x0E) | \
 140                                 FTIM2_NOR_TWP(0x1c))
 141 #define CONFIG_SYS_NOR_FTIM3    0x0
 142
 143 #define CONFIG_SYS_FLASH_QUIET_TEST
 144 #define CONFIG_FLASH_SHOW_PROGRESS      45 /* count down from 45/5: 9..1 */
 145
 146 #define CONFIG_SYS_MAX_FLASH_SECT       1024    /* sectors per device */
 147 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000   /* Flash Erase Timeout (ms) */
 148 #define CONFIG_SYS_FLASH_WRITE_TOUT     500     /* Flash Write Timeout (ms) */
 149 #define CONFIG_SYS_FLASH_EMPTY_INFO
 150 #define CONFIG_SYS_FLASH_BANKS_LIST     {CONFIG_SYS_FLASH_BASE_PHYS }
 151
 152 /* CPLD on IFC */
 153 #define CONFIG_SYS_CPLD_BASE    0xffdf0000
 154 #define CONFIG_SYS_CPLD_BASE_PHYS       (0xf00000000ull | CONFIG_SYS_CPLD_BASE)
 155 #define CONFIG_SYS_CSPR2_EXT    (0xf)
 156 #define CONFIG_SYS_CSPR2        (CSPR_PHYS_ADDR(CONFIG_SYS_CPLD_BASE) \
 157                                 | CSPR_PORT_SIZE_8 \
 158                                 | CSPR_MSEL_GPCM \
 159                                 | CSPR_V)
 160 #define CONFIG_SYS_AMASK2       IFC_AMASK(64*1024)
 161 #define CONFIG_SYS_CSOR2        0x0
 162
 163 /* CPLD Timing parameters for IFC CS2 */
 164 #define CONFIG_SYS_CS2_FTIM0            (FTIM0_GPCM_TACSE(0x0e) | \
 165                                         FTIM0_GPCM_TEADC(0x0e) | \
 166                                         FTIM0_GPCM_TEAHC(0x0e))
 167 #define CONFIG_SYS_CS2_FTIM1            (FTIM1_GPCM_TACO(0x0e) | \
 168                                         FTIM1_GPCM_TRAD(0x1f))
 169 #define CONFIG_SYS_CS2_FTIM2            (FTIM2_GPCM_TCS(0x0e) | \
 170                                         FTIM2_GPCM_TCH(0x8) | \
 171                                         FTIM2_GPCM_TWP(0x1f))
 172 #define CONFIG_SYS_CS2_FTIM3            0x0
 173
 174 /* NAND Flash on IFC */
 175 #define CONFIG_SYS_NAND_BASE            0xff800000
 176 #define CONFIG_SYS_NAND_BASE_PHYS       (0xf00000000ull | CONFIG_SYS_NAND_BASE)
 177
 178 #define CONFIG_SYS_NAND_CSPR_EXT        (0xf)
 179 #define CONFIG_SYS_NAND_CSPR    (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
 180                                 | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
 181                                 | CSPR_MSEL_NAND         /* MSEL = NAND */ \
 182                                 | CSPR_V)
 183 #define CONFIG_SYS_NAND_AMASK   IFC_AMASK(64*1024)
 184
 185 #define CONFIG_SYS_NAND_CSOR    (CSOR_NAND_ECC_ENC_EN   /* ECC on encode */ \
 186                                 | CSOR_NAND_ECC_DEC_EN  /* ECC on decode */ \
 187                                 | CSOR_NAND_ECC_MODE_4  /* 4-bit ECC */     \
 188                                 | CSOR_NAND_RAL_3       /* RAL = 2Byes */   \
 189                                 | CSOR_NAND_PGS_2K      /* Page Size = 2K */\
 190                                 | CSOR_NAND_SPRZ_64     /* Spare size = 64 */\
 191                                 | CSOR_NAND_PB(64))     /*Pages Per Block = 64*/
 192
 193 /* ONFI NAND Flash mode0 Timing Params */
 194 #define CONFIG_SYS_NAND_FTIM0           (FTIM0_NAND_TCCST(0x07) | \
 195                                         FTIM0_NAND_TWP(0x18)    | \
 196                                         FTIM0_NAND_TWCHT(0x07)  | \
 197                                         FTIM0_NAND_TWH(0x0a))
 198 #define CONFIG_SYS_NAND_FTIM1           (FTIM1_NAND_TADLE(0x32) | \
 199                                         FTIM1_NAND_TWBE(0x39)   | \
 200                                         FTIM1_NAND_TRR(0x0e)    | \
 201                                         FTIM1_NAND_TRP(0x18))
 202 #define CONFIG_SYS_NAND_FTIM2           (FTIM2_NAND_TRAD(0x0f)  | \
 203                                         FTIM2_NAND_TREH(0x0a)   | \
 204                                         FTIM2_NAND_TWHRE(0x1e))
 205 #define CONFIG_SYS_NAND_FTIM3           0x0
 206
 207 #define CONFIG_SYS_NAND_DDR_LAW         11
 208 #define CONFIG_SYS_NAND_BASE_LIST       { CONFIG_SYS_NAND_BASE }
 209 #define CONFIG_SYS_MAX_NAND_DEVICE      1
 210
 211 #if defined(CONFIG_MTD_RAW_NAND)
 212 #define CONFIG_SYS_CSPR0_EXT            CONFIG_SYS_NAND_CSPR_EXT
 213 #define CONFIG_SYS_CSPR0                CONFIG_SYS_NAND_CSPR
 214 #define CONFIG_SYS_AMASK0               CONFIG_SYS_NAND_AMASK
 215 #define CONFIG_SYS_CSOR0                CONFIG_SYS_NAND_CSOR
 216 #define CONFIG_SYS_CS0_FTIM0            CONFIG_SYS_NAND_FTIM0
 217 #define CONFIG_SYS_CS0_FTIM1            CONFIG_SYS_NAND_FTIM1
 218 #define CONFIG_SYS_CS0_FTIM2            CONFIG_SYS_NAND_FTIM2
 219 #define CONFIG_SYS_CS0_FTIM3            CONFIG_SYS_NAND_FTIM3
 220 #define CONFIG_SYS_CSPR1_EXT            CONFIG_SYS_NOR0_CSPR_EXT
 221 #define CONFIG_SYS_CSPR1                CONFIG_SYS_NOR0_CSPR
 222 #define CONFIG_SYS_AMASK1               CONFIG_SYS_NOR_AMASK
 223 #define CONFIG_SYS_CSOR1                CONFIG_SYS_NOR_CSOR
 224 #define CONFIG_SYS_CS1_FTIM0            CONFIG_SYS_NOR_FTIM0
 225 #define CONFIG_SYS_CS1_FTIM1            CONFIG_SYS_NOR_FTIM1
 226 #define CONFIG_SYS_CS1_FTIM2            CONFIG_SYS_NOR_FTIM2
 227 #define CONFIG_SYS_CS1_FTIM3            CONFIG_SYS_NOR_FTIM3
 228 #else
 229 #define CONFIG_SYS_CSPR0_EXT            CONFIG_SYS_NOR0_CSPR_EXT
 230 #define CONFIG_SYS_CSPR0                CONFIG_SYS_NOR0_CSPR
 231 #define CONFIG_SYS_AMASK0               CONFIG_SYS_NOR_AMASK
 232 #define CONFIG_SYS_CSOR0                CONFIG_SYS_NOR_CSOR
 233 #define CONFIG_SYS_CS0_FTIM0            CONFIG_SYS_NOR_FTIM0
 234 #define CONFIG_SYS_CS0_FTIM1            CONFIG_SYS_NOR_FTIM1
 235 #define CONFIG_SYS_CS0_FTIM2            CONFIG_SYS_NOR_FTIM2
 236 #define CONFIG_SYS_CS0_FTIM3            CONFIG_SYS_NOR_FTIM3
 237 #define CONFIG_SYS_CSPR1_EXT            CONFIG_SYS_NAND_CSPR_EXT
 238 #define CONFIG_SYS_CSPR1                CONFIG_SYS_NAND_CSPR
 239 #define CONFIG_SYS_AMASK1               CONFIG_SYS_NAND_AMASK
 240 #define CONFIG_SYS_CSOR1                CONFIG_SYS_NAND_CSOR
 241 #define CONFIG_SYS_CS1_FTIM0            CONFIG_SYS_NAND_FTIM0
 242 #define CONFIG_SYS_CS1_FTIM1            CONFIG_SYS_NAND_FTIM1
 243 #define CONFIG_SYS_CS1_FTIM2            CONFIG_SYS_NAND_FTIM2
 244 #define CONFIG_SYS_CS1_FTIM3            CONFIG_SYS_NAND_FTIM3
 245 #endif
 246
 247 #if defined(CONFIG_RAMBOOT_PBL)
 248 #define CONFIG_SYS_RAMBOOT
 249 #endif
 250
 251 #define CONFIG_HWCONFIG
 252
 253 /* define to use L1 as initial stack */
 254 #define CONFIG_L1_INIT_RAM
 255 #define CONFIG_SYS_INIT_RAM_LOCK
 256 #define CONFIG_SYS_INIT_RAM_ADDR        0xfdd00000 /* Initial L1 address */
 257 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH      0xf
 258 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW       0xfe03c000
 259 /* The assembler doesn't like typecast */
 260 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
 261                         ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
 262                         CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
 263 #define CONFIG_SYS_INIT_RAM_SIZE        0x00004000
 264 #define CONFIG_SYS_INIT_SP_OFFSET       (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 265 #define CONFIG_SYS_MONITOR_LEN          (768 * 1024)
 266
 267 /*
 268  * Serial Port
 269  */
 270 #define CONFIG_SYS_NS16550_SERIAL
 271 #define CONFIG_SYS_NS16550_REG_SIZE     1
 272 #define CONFIG_SYS_NS16550_CLK          (get_bus_freq(0)/2)
 273 #define CONFIG_SYS_BAUDRATE_TABLE       \
 274         {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
 275 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500)
 276 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600)
 277 #define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500)
 278 #define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600)
 279
 280 /*
 281  * I2C
 282  */
 283
 284 #define I2C_MUX_PCA_ADDR_PRI    0x77 /* I2C bus multiplexer,primary */
 285 #define I2C_MUX_PCA_ADDR_SEC1   0x75 /* I2C bus multiplexer,secondary 1 */
 286 #define I2C_MUX_PCA_ADDR_SEC2   0x76 /* I2C bus multiplexer,secondary 2 */
 287 #define I2C_MUX_CH_DEFAULT      0x8
 288
 289 #define I2C_MUX_CH_VOL_MONITOR  0xa
 290
 291 /* The lowest and highest voltage allowed for T208xRDB */
 292 #define VDD_MV_MIN                      819
 293 #define VDD_MV_MAX                      1212
 294
 295 /*
 296  * RapidIO
 297  */
 298 #define CONFIG_SYS_SRIO1_MEM_VIRT       0xa0000000
 299 #define CONFIG_SYS_SRIO1_MEM_PHYS       0xc20000000ull
 300 #define CONFIG_SYS_SRIO1_MEM_SIZE       0x10000000 /* 256M */
 301 #define CONFIG_SYS_SRIO2_MEM_VIRT       0xb0000000
 302 #define CONFIG_SYS_SRIO2_MEM_PHYS       0xc30000000ull
 303 #define CONFIG_SYS_SRIO2_MEM_SIZE       0x10000000 /* 256M */
 304 /*
 305  * for slave u-boot IMAGE instored in master memory space,
 306  * PHYS must be aligned based on the SIZE
 307  */
 308 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull
 309 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull
 310 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE     0x100000 /* 1M */
 311 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull
 312 /*
 313  * for slave UCODE and ENV instored in master memory space,
 314  * PHYS must be aligned based on the SIZE
 315  */
 316 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull
 317 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull
 318 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE    0x40000 /* 256K */
 319
 320 /* slave core release by master*/
 321 #define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4
 322 #define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */
 323
 324 /*
 325  * SRIO_PCIE_BOOT - SLAVE
 326  */
 327 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
 328 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000
 329 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \
 330                 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR)
 331 #endif
 332
 333 /*
 334  * eSPI - Enhanced SPI
 335  */
 336
 337 /*
 338  * General PCI
 339  * Memory space is mapped 1-1, but I/O space must start from 0.
 340  */
 341 #define CONFIG_PCIE1            /* PCIE controller 1 */
 342 #define CONFIG_PCIE2            /* PCIE controller 2 */
 343 #define CONFIG_PCIE3            /* PCIE controller 3 */
 344 #define CONFIG_PCIE4            /* PCIE controller 4 */
 345 /* controller 1, direct to uli, tgtid 3, Base address 20000 */
 346 #define CONFIG_SYS_PCIE1_MEM_VIRT       0x80000000
 347 #define CONFIG_SYS_PCIE1_MEM_PHYS       0xc00000000ull
 348 #define CONFIG_SYS_PCIE1_IO_VIRT        0xf8000000
 349 #define CONFIG_SYS_PCIE1_IO_PHYS        0xff8000000ull
 350
 351 /* controller 2, Slot 2, tgtid 2, Base address 201000 */
 352 #define CONFIG_SYS_PCIE2_MEM_VIRT       0xa0000000
 353 #define CONFIG_SYS_PCIE2_MEM_PHYS       0xc20000000ull
 354 #define CONFIG_SYS_PCIE2_IO_VIRT        0xf8010000
 355 #define CONFIG_SYS_PCIE2_IO_PHYS        0xff8010000ull
 356
 357 /* controller 3, Slot 1, tgtid 1, Base address 202000 */
 358 #define CONFIG_SYS_PCIE3_MEM_VIRT       0xb0000000
 359 #define CONFIG_SYS_PCIE3_MEM_PHYS       0xc30000000ull
 360 #define CONFIG_SYS_PCIE3_IO_VIRT        0xf8020000
 361 #define CONFIG_SYS_PCIE3_IO_PHYS        0xff8020000ull
 362
 363 /* controller 4, Base address 203000 */
 364 #define CONFIG_SYS_PCIE4_MEM_VIRT       0xc0000000
 365 #define CONFIG_SYS_PCIE4_MEM_PHYS       0xc40000000ull
 366 #define CONFIG_SYS_PCIE4_IO_PHYS        0xff8030000ull
 367
 368 #ifdef CONFIG_PCI
 369 #define CONFIG_PCI_SCAN_SHOW    /* show pci devices on startup */
 370 #endif
 371
 372 /* Qman/Bman */
 373 #ifndef CONFIG_NOBQFMAN
 374 #define CONFIG_SYS_BMAN_NUM_PORTALS     18
 375 #define CONFIG_SYS_BMAN_MEM_BASE        0xf4000000
 376 #define CONFIG_SYS_BMAN_MEM_PHYS        0xff4000000ull
 377 #define CONFIG_SYS_BMAN_MEM_SIZE        0x02000000
 378 #define CONFIG_SYS_BMAN_SP_CENA_SIZE    0x4000
 379 #define CONFIG_SYS_BMAN_SP_CINH_SIZE    0x1000
 380 #define CONFIG_SYS_BMAN_CENA_BASE       CONFIG_SYS_BMAN_MEM_BASE
 381 #define CONFIG_SYS_BMAN_CENA_SIZE       (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
 382 #define CONFIG_SYS_BMAN_CINH_BASE       (CONFIG_SYS_BMAN_MEM_BASE + \
 383                                         CONFIG_SYS_BMAN_CENA_SIZE)
 384 #define CONFIG_SYS_BMAN_CINH_SIZE       (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
 385 #define CONFIG_SYS_BMAN_SWP_ISDR_REG    0xE08
 386 #define CONFIG_SYS_QMAN_NUM_PORTALS     18
 387 #define CONFIG_SYS_QMAN_MEM_BASE        0xf6000000
 388 #define CONFIG_SYS_QMAN_MEM_PHYS        0xff6000000ull
 389 #define CONFIG_SYS_QMAN_MEM_SIZE        0x02000000
 390 #define CONFIG_SYS_QMAN_SP_CENA_SIZE    0x4000
 391 #define CONFIG_SYS_QMAN_SP_CINH_SIZE    0x1000
 392 #define CONFIG_SYS_QMAN_CENA_BASE       CONFIG_SYS_QMAN_MEM_BASE
 393 #define CONFIG_SYS_QMAN_CENA_SIZE       (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
 394 #define CONFIG_SYS_QMAN_CINH_BASE       (CONFIG_SYS_QMAN_MEM_BASE + \
 395                                         CONFIG_SYS_QMAN_CENA_SIZE)
 396 #define CONFIG_SYS_QMAN_CINH_SIZE       (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
 397 #define CONFIG_SYS_QMAN_SWP_ISDR_REG    0xE08
 398
 399 #define CONFIG_SYS_DPAA_FMAN
 400 #define CONFIG_SYS_DPAA_PME
 401 #define CONFIG_SYS_PMAN
 402 #define CONFIG_SYS_DPAA_DCE
 403 #define CONFIG_SYS_DPAA_RMAN            /* RMan */
 404 #define CONFIG_SYS_INTERLAKEN
 405
 406 #define CONFIG_SYS_FDT_PAD              (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
 407 #endif /* CONFIG_NOBQFMAN */
 408
 409 #ifdef CONFIG_SYS_DPAA_FMAN
 410 #define RGMII_PHY1_ADDR         0x01  /* RealTek RTL8211E */
 411 #define RGMII_PHY2_ADDR         0x02
 412 #define CORTINA_PHY_ADDR1       0x0c  /* Cortina CS4315 */
 413 #define CORTINA_PHY_ADDR2       0x0d
 414 /* Aquantia AQ1202 10G Base-T used by board revisions up to C */
 415 #define FM1_10GEC3_PHY_ADDR     0x00
 416 #define FM1_10GEC4_PHY_ADDR     0x01
 417 /* Aquantia AQR113C 10G Base-T used by board revisions D and up */
 418 #define AQR113C_PHY_ADDR1       0x00
 419 #define AQR113C_PHY_ADDR2       0x08
 420 #endif
 421
 422 /*
 423  * SATA
 424  */
 425 #ifdef CONFIG_FSL_SATA_V2
 426 #define CONFIG_SATA1
 427 #define CONFIG_SYS_SATA1                CONFIG_SYS_MPC85xx_SATA1_ADDR
 428 #define CONFIG_SYS_SATA1_FLAGS          FLAGS_DMA
 429 #define CONFIG_SATA2
 430 #define CONFIG_SYS_SATA2                CONFIG_SYS_MPC85xx_SATA2_ADDR
 431 #define CONFIG_SYS_SATA2_FLAGS          FLAGS_DMA
 432 #define CONFIG_LBA48
 433 #endif
 434
 435 /*
 436  * USB
 437  */
 438 #ifdef CONFIG_USB_EHCI_HCD
 439 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 440 #define CONFIG_HAS_FSL_DR_USB
 441 #endif
 442
 443 /*
 444  * SDHC
 445  */
 446 #ifdef CONFIG_MMC
 447 #define CONFIG_SYS_FSL_ESDHC_ADDR       CONFIG_SYS_MPC85xx_ESDHC_ADDR
 448 #define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT
 449 #endif
 450
 451 /*
 452  * Dynamic MTD Partition support with mtdparts
 453  */
 454
 455 /*
 456  * Environment
 457  */
 458
 459 /*
 460  * Miscellaneous configurable options
 461  */
 462
 463 /*
 464  * For booting Linux, the board info and command line data
 465  * have to be in the first 64 MB of memory, since this is
 466  * the maximum mapped by the Linux kernel during initialization.
 467  */
 468 #define CONFIG_SYS_BOOTMAPSZ    (64 << 20)      /* Initial map for Linux*/
 469 #define CONFIG_SYS_BOOTM_LEN    (64 << 20)      /* Increase max gunzip size */
 470
 471 /*
 472  * Environment Configuration
 473  */
 474 #define CONFIG_ROOTPATH  "/opt/nfsroot"
 475 #define CONFIG_UBOOTPATH "u-boot.bin"   /* U-Boot image on TFTP server */
 476
 477 #define __USB_PHY_TYPE          utmi
 478
 479 #define CONFIG_EXTRA_ENV_SETTINGS                               \
 480         "hwconfig=fsl_ddr:"                                     \
 481         "ctlr_intlv=" __stringify(CTRL_INTLV_PREFERED) ","      \
 482         "bank_intlv=auto;"                                      \
 483         "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\
 484         "netdev=eth0\0"                                         \
 485         "uboot=" __stringify(CONFIG_UBOOTPATH) "\0"             \
 486         "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0"     \
 487         "tftpflash=tftpboot $loadaddr $uboot && "               \
 488         "protect off $ubootaddr +$filesize && "                 \
 489         "erase $ubootaddr +$filesize && "                       \
 490         "cp.b $loadaddr $ubootaddr $filesize && "               \
 491         "protect on $ubootaddr +$filesize && "                  \
 492         "cmp.b $loadaddr $ubootaddr $filesize\0"                \
 493         "consoledev=ttyS0\0"                                    \
 494         "ramdiskaddr=2000000\0"                                 \
 495         "ramdiskfile=t2080rdb/ramdisk.uboot\0"                  \
 496         "fdtaddr=1e00000\0"                                     \
 497         "fdtfile=t2080rdb/t2080rdb.dtb\0"                       \
 498         "bdev=sda3\0"
 499
 500 /*
 501  * For emulation this causes u-boot to jump to the start of the
 502  * proof point app code automatically
 503  */
 504 #define PROOF_POINTS                            \
 505         "setenv bootargs root=/dev/$bdev rw "           \
 506         "console=$consoledev,$baudrate $othbootargs;"   \
 507         "cpu 1 release 0x29000000 - - -;"               \
 508         "cpu 2 release 0x29000000 - - -;"               \
 509         "cpu 3 release 0x29000000 - - -;"               \
 510         "cpu 4 release 0x29000000 - - -;"               \
 511         "cpu 5 release 0x29000000 - - -;"               \
 512         "cpu 6 release 0x29000000 - - -;"               \
 513         "cpu 7 release 0x29000000 - - -;"               \
 514         "go 0x29000000"
 515
 516 #define HVBOOT                          \
 517         "setenv bootargs config-addr=0x60000000; "      \
 518         "bootm 0x01000000 - 0x00f00000"
 519
 520 #define ALU                             \
 521         "setenv bootargs root=/dev/$bdev rw "           \
 522         "console=$consoledev,$baudrate $othbootargs;"   \
 523         "cpu 1 release 0x01000000 - - -;"               \
 524         "cpu 2 release 0x01000000 - - -;"               \
 525         "cpu 3 release 0x01000000 - - -;"               \
 526         "cpu 4 release 0x01000000 - - -;"               \
 527         "cpu 5 release 0x01000000 - - -;"               \
 528         "cpu 6 release 0x01000000 - - -;"               \
 529         "cpu 7 release 0x01000000 - - -;"               \
 530         "go 0x01000000"
 531
 532 #include <asm/fsl_secure_boot.h>
 533
 534 #endif  /* __T2080RDB_H */