include/configs/T208xRDB.h

   1 /*
   2  * Copyright 2014 Freescale Semiconductor, Inc.
   3  *
   4  * SPDX-License-Identifier:     GPL-2.0+
   5  */
   6
   7 /*
   8  * T2080 RDB/PCIe board configuration file
   9  */
  10
  11 #ifndef __T2080RDB_H
  12 #define __T2080RDB_H
  13
  14 #define CONFIG_DISPLAY_BOARDINFO
  15 #define CONFIG_T2080RDB
  16 #define CONFIG_ICS307_REFCLK_HZ 25000000  /* ICS307 ref clk freq */
  17 #define CONFIG_MMC
  18 #define CONFIG_USB_EHCI
  19 #define CONFIG_FSL_SATA_V2
  20
  21 /* High Level Configuration Options */
  22 #define CONFIG_PHYS_64BIT
  23 #define CONFIG_BOOKE
  24 #define CONFIG_E500             /* BOOKE e500 family */
  25 #define CONFIG_E500MC           /* BOOKE e500mc family */
  26 #define CONFIG_SYS_BOOK3E_HV    /* Category E.HV supported */
  27 #define CONFIG_MP               /* support multiple processors */
  28 #define CONFIG_ENABLE_36BIT_PHYS
  29
  30 #ifdef CONFIG_PHYS_64BIT
  31 #define CONFIG_ADDR_MAP 1
  32 #define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */
  33 #endif
  34
  35 #define CONFIG_SYS_FSL_CPC      /* Corenet Platform Cache */
  36 #define CONFIG_SYS_NUM_CPC      CONFIG_NUM_DDR_CONTROLLERS
  37 #define CONFIG_FSL_IFC          /* Enable IFC Support */
  38 #define CONFIG_FSL_CAAM         /* Enable SEC/CAAM */
  39 #define CONFIG_FSL_LAW          /* Use common FSL init code */
  40 #define CONFIG_ENV_OVERWRITE
  41
  42 #ifdef CONFIG_RAMBOOT_PBL
  43 #define CONFIG_SYS_FSL_PBL_PBI board/freescale/t208xrdb/t2080_pbi.cfg
  44 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xrdb/t2080_rcw.cfg
  45
  46 #define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT
  47 #define CONFIG_SPL_ENV_SUPPORT
  48 #define CONFIG_SPL_SERIAL_SUPPORT
  49 #define CONFIG_SPL_FLUSH_IMAGE
  50 #define CONFIG_SPL_TARGET               "u-boot-with-spl.bin"
  51 #define CONFIG_SPL_LIBGENERIC_SUPPORT
  52 #define CONFIG_SPL_LIBCOMMON_SUPPORT
  53 #define CONFIG_SPL_I2C_SUPPORT
  54 #define CONFIG_SPL_DRIVERS_MISC_SUPPORT
  55 #define CONFIG_FSL_LAW                  /* Use common FSL init code */
  56 #define CONFIG_SYS_TEXT_BASE            0x00201000
  57 #define CONFIG_SPL_TEXT_BASE            0xFFFD8000
  58 #define CONFIG_SPL_PAD_TO               0x40000
  59 #define CONFIG_SPL_MAX_SIZE             0x28000
  60 #define RESET_VECTOR_OFFSET             0x27FFC
  61 #define BOOT_PAGE_OFFSET                0x27000
  62 #ifdef CONFIG_SPL_BUILD
  63 #define CONFIG_SPL_SKIP_RELOCATE
  64 #define CONFIG_SPL_COMMON_INIT_DDR
  65 #define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
  66 #define CONFIG_SYS_NO_FLASH
  67 #endif
  68
  69 #ifdef CONFIG_NAND
  70 #define CONFIG_SPL_NAND_SUPPORT
  71 #define CONFIG_SYS_NAND_U_BOOT_SIZE     (768 << 10)
  72 #define CONFIG_SYS_NAND_U_BOOT_DST      0x00200000
  73 #define CONFIG_SYS_NAND_U_BOOT_START    0x00200000
  74 #define CONFIG_SYS_NAND_U_BOOT_OFFS     (256 << 10)
  75 #define CONFIG_SYS_LDSCRIPT  "arch/powerpc/cpu/mpc85xx/u-boot-nand.lds"
  76 #define CONFIG_SPL_NAND_BOOT
  77 #endif
  78
  79 #ifdef CONFIG_SPIFLASH
  80 #define        CONFIG_RESET_VECTOR_ADDRESS             0x200FFC
  81 #define CONFIG_SPL_SPI_SUPPORT
  82 #define CONFIG_SPL_SPI_FLASH_SUPPORT
  83 #define CONFIG_SPL_SPI_FLASH_MINIMAL
  84 #define CONFIG_SYS_SPI_FLASH_U_BOOT_SIZE       (768 << 10)
  85 #define CONFIG_SYS_SPI_FLASH_U_BOOT_DST                (0x00200000)
  86 #define CONFIG_SYS_SPI_FLASH_U_BOOT_START      (0x00200000)
  87 #define CONFIG_SYS_SPI_FLASH_U_BOOT_OFFS       (256 << 10)
  88 #define CONFIG_SYS_LDSCRIPT    "arch/powerpc/cpu/mpc85xx/u-boot.lds"
  89 #ifndef CONFIG_SPL_BUILD
  90 #define CONFIG_SYS_MPC85XX_NO_RESETVEC
  91 #endif
  92 #define CONFIG_SPL_SPI_BOOT
  93 #endif
  94
  95 #ifdef CONFIG_SDCARD
  96 #define        CONFIG_RESET_VECTOR_ADDRESS             0x200FFC
  97 #define CONFIG_SPL_MMC_SUPPORT
  98 #define CONFIG_SPL_MMC_MINIMAL
  99 #define CONFIG_SYS_MMC_U_BOOT_SIZE     (768 << 10)
 100 #define CONFIG_SYS_MMC_U_BOOT_DST      (0x00200000)
 101 #define CONFIG_SYS_MMC_U_BOOT_START    (0x00200000)
 102 #define CONFIG_SYS_MMC_U_BOOT_OFFS     (260 << 10)
 103 #define CONFIG_SYS_LDSCRIPT    "arch/powerpc/cpu/mpc85xx/u-boot.lds"
 104 #ifndef CONFIG_SPL_BUILD
 105 #define CONFIG_SYS_MPC85XX_NO_RESETVEC
 106 #endif
 107 #define CONFIG_SPL_MMC_BOOT
 108 #endif
 109
 110 #endif /* CONFIG_RAMBOOT_PBL */
 111
 112 #define CONFIG_SRIO_PCIE_BOOT_MASTER
 113 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
 114 /* Set 1M boot space */
 115 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000)
 116 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \
 117                 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR)
 118 #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
 119 #define CONFIG_SYS_NO_FLASH
 120 #endif
 121
 122 #ifndef CONFIG_SYS_TEXT_BASE
 123 #define CONFIG_SYS_TEXT_BASE    0xeff40000
 124 #endif
 125
 126 #ifndef CONFIG_RESET_VECTOR_ADDRESS
 127 #define CONFIG_RESET_VECTOR_ADDRESS     0xeffffffc
 128 #endif
 129
 130 /*
 131  * These can be toggled for performance analysis, otherwise use default.
 132  */
 133 #define CONFIG_SYS_CACHE_STASHING
 134 #define CONFIG_BTB              /* toggle branch predition */
 135 #define CONFIG_DDR_ECC
 136 #ifdef CONFIG_DDR_ECC
 137 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
 138 #define CONFIG_MEM_INIT_VALUE           0xdeadbeef
 139 #endif
 140
 141 #define CONFIG_SYS_MEMTEST_START        0x00200000 /* memtest works on */
 142 #define CONFIG_SYS_MEMTEST_END          0x00400000
 143 #define CONFIG_SYS_ALT_MEMTEST
 144
 145 #ifndef CONFIG_SYS_NO_FLASH
 146 #define CONFIG_FLASH_CFI_DRIVER
 147 #define CONFIG_SYS_FLASH_CFI
 148 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
 149 #endif
 150
 151 #if defined(CONFIG_SPIFLASH)
 152 #define CONFIG_SYS_EXTRA_ENV_RELOC
 153 #define CONFIG_ENV_IS_IN_SPI_FLASH
 154 #define CONFIG_ENV_SPI_BUS      0
 155 #define CONFIG_ENV_SPI_CS       0
 156 #define CONFIG_ENV_SPI_MAX_HZ   10000000
 157 #define CONFIG_ENV_SPI_MODE     0
 158 #define CONFIG_ENV_SIZE         0x2000     /* 8KB */
 159 #define CONFIG_ENV_OFFSET       0x100000   /* 1MB */
 160 #define CONFIG_ENV_SECT_SIZE    0x10000
 161 #elif defined(CONFIG_SDCARD)
 162 #define CONFIG_SYS_EXTRA_ENV_RELOC
 163 #define CONFIG_ENV_IS_IN_MMC
 164 #define CONFIG_SYS_MMC_ENV_DEV  0
 165 #define CONFIG_ENV_SIZE         0x2000
 166 #define CONFIG_ENV_OFFSET       (512 * 0x800)
 167 #elif defined(CONFIG_NAND)
 168 #define CONFIG_SYS_EXTRA_ENV_RELOC
 169 #define CONFIG_ENV_IS_IN_NAND
 170 #define CONFIG_ENV_SIZE         0x2000
 171 #define CONFIG_ENV_OFFSET       (2 * CONFIG_SYS_NAND_BLOCK_SIZE)
 172 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
 173 #define CONFIG_ENV_IS_IN_REMOTE
 174 #define CONFIG_ENV_ADDR         0xffe20000
 175 #define CONFIG_ENV_SIZE         0x2000
 176 #elif defined(CONFIG_ENV_IS_NOWHERE)
 177 #define CONFIG_ENV_SIZE         0x2000
 178 #else
 179 #define CONFIG_ENV_IS_IN_FLASH
 180 #define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
 181 #define CONFIG_ENV_SIZE         0x2000
 182 #define CONFIG_ENV_SECT_SIZE    0x20000 /* 128K (one sector) */
 183 #endif
 184
 185 #ifndef __ASSEMBLY__
 186 unsigned long get_board_sys_clk(void);
 187 unsigned long get_board_ddr_clk(void);
 188 #endif
 189
 190 #define CONFIG_SYS_CLK_FREQ     66660000
 191 #define CONFIG_DDR_CLK_FREQ     133330000
 192
 193 /*
 194  * Config the L3 Cache as L3 SRAM
 195  */
 196 #define CONFIG_SYS_INIT_L3_ADDR         0xFFFC0000
 197 #define CONFIG_SYS_L3_SIZE              (512 << 10)
 198 #define CONFIG_SPL_GD_ADDR              (CONFIG_SYS_INIT_L3_ADDR + 32 * 1024)
 199 #ifdef CONFIG_RAMBOOT_PBL
 200 #define CONFIG_ENV_ADDR                 (CONFIG_SPL_GD_ADDR + 4 * 1024)
 201 #endif
 202 #define CONFIG_SPL_RELOC_MALLOC_ADDR    (CONFIG_SPL_GD_ADDR + 12 * 1024)
 203 #define CONFIG_SPL_RELOC_MALLOC_SIZE    (50 << 10)
 204 #define CONFIG_SPL_RELOC_STACK          (CONFIG_SPL_GD_ADDR + 64 * 1024)
 205 #define CONFIG_SPL_RELOC_STACK_SIZE     (22 << 10)
 206
 207 #define CONFIG_SYS_DCSRBAR      0xf0000000
 208 #define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull
 209
 210 /* EEPROM */
 211 #define CONFIG_ID_EEPROM
 212 #define CONFIG_SYS_I2C_EEPROM_NXID
 213 #define CONFIG_SYS_EEPROM_BUS_NUM       0
 214 #define CONFIG_SYS_I2C_EEPROM_ADDR      0x50
 215 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN  2
 216
 217 /*
 218  * DDR Setup
 219  */
 220 #define CONFIG_VERY_BIG_RAM
 221 #define CONFIG_SYS_DDR_SDRAM_BASE       0x00000000
 222 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE
 223 #define CONFIG_DIMM_SLOTS_PER_CTLR      1
 224 #define CONFIG_CHIP_SELECTS_PER_CTRL    (4 * CONFIG_DIMM_SLOTS_PER_CTLR)
 225 #define CONFIG_DDR_SPD
 226 #define CONFIG_SYS_FSL_DDR3
 227 #undef CONFIG_FSL_DDR_INTERACTIVE
 228 #define CONFIG_SYS_SPD_BUS_NUM  0
 229 #define CONFIG_SYS_SDRAM_SIZE   2048    /* for fixed parameter use */
 230 #define SPD_EEPROM_ADDRESS1     0x51
 231 #define SPD_EEPROM_ADDRESS2     0x52
 232 #define SPD_EEPROM_ADDRESS      SPD_EEPROM_ADDRESS1
 233 #define CTRL_INTLV_PREFERED     cacheline
 234
 235 /*
 236  * IFC Definitions
 237  */
 238 #define CONFIG_SYS_FLASH_BASE           0xe8000000
 239 #define CONFIG_SYS_FLASH_BASE_PHYS      (0xf00000000ull | CONFIG_SYS_FLASH_BASE)
 240 #define CONFIG_SYS_NOR0_CSPR_EXT        (0xf)
 241 #define CONFIG_SYS_NOR0_CSPR    (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
 242                                 CSPR_PORT_SIZE_16 | \
 243                                 CSPR_MSEL_NOR | \
 244                                 CSPR_V)
 245 #define CONFIG_SYS_NOR_AMASK    IFC_AMASK(128*1024*1024)
 246
 247 /* NOR Flash Timing Params */
 248 #define CONFIG_SYS_NOR_CSOR     CSOR_NAND_TRHZ_80
 249
 250 #define CONFIG_SYS_NOR_FTIM0    (FTIM0_NOR_TACSE(0x4) | \
 251                                 FTIM0_NOR_TEADC(0x5) | \
 252                                 FTIM0_NOR_TEAHC(0x5))
 253 #define CONFIG_SYS_NOR_FTIM1    (FTIM1_NOR_TACO(0x35) | \
 254                                 FTIM1_NOR_TRAD_NOR(0x1A) |\
 255                                 FTIM1_NOR_TSEQRAD_NOR(0x13))
 256 #define CONFIG_SYS_NOR_FTIM2    (FTIM2_NOR_TCS(0x4) | \
 257                                 FTIM2_NOR_TCH(0x4) | \
 258                                 FTIM2_NOR_TWPH(0x0E) | \
 259                                 FTIM2_NOR_TWP(0x1c))
 260 #define CONFIG_SYS_NOR_FTIM3    0x0
 261
 262 #define CONFIG_SYS_FLASH_QUIET_TEST
 263 #define CONFIG_FLASH_SHOW_PROGRESS      45 /* count down from 45/5: 9..1 */
 264
 265 #define CONFIG_SYS_MAX_FLASH_BANKS      1       /* number of banks */
 266 #define CONFIG_SYS_MAX_FLASH_SECT       1024    /* sectors per device */
 267 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000   /* Flash Erase Timeout (ms) */
 268 #define CONFIG_SYS_FLASH_WRITE_TOUT     500     /* Flash Write Timeout (ms) */
 269 #define CONFIG_SYS_FLASH_EMPTY_INFO
 270 #define CONFIG_SYS_FLASH_BANKS_LIST     {CONFIG_SYS_FLASH_BASE_PHYS }
 271
 272 /* CPLD on IFC */
 273 #define CONFIG_SYS_CPLD_BASE    0xffdf0000
 274 #define CONFIG_SYS_CPLD_BASE_PHYS       (0xf00000000ull | CONFIG_SYS_CPLD_BASE)
 275 #define CONFIG_SYS_CSPR2_EXT    (0xf)
 276 #define CONFIG_SYS_CSPR2        (CSPR_PHYS_ADDR(CONFIG_SYS_CPLD_BASE) \
 277                                 | CSPR_PORT_SIZE_8 \
 278                                 | CSPR_MSEL_GPCM \
 279                                 | CSPR_V)
 280 #define CONFIG_SYS_AMASK2       IFC_AMASK(64*1024)
 281 #define CONFIG_SYS_CSOR2        0x0
 282
 283 /* CPLD Timing parameters for IFC CS2 */
 284 #define CONFIG_SYS_CS2_FTIM0            (FTIM0_GPCM_TACSE(0x0e) | \
 285                                         FTIM0_GPCM_TEADC(0x0e) | \
 286                                         FTIM0_GPCM_TEAHC(0x0e))
 287 #define CONFIG_SYS_CS2_FTIM1            (FTIM1_GPCM_TACO(0x0e) | \
 288                                         FTIM1_GPCM_TRAD(0x1f))
 289 #define CONFIG_SYS_CS2_FTIM2            (FTIM2_GPCM_TCS(0x0e) | \
 290                                         FTIM2_GPCM_TCH(0x8) | \
 291                                         FTIM2_GPCM_TWP(0x1f))
 292 #define CONFIG_SYS_CS2_FTIM3            0x0
 293
 294 /* NAND Flash on IFC */
 295 #define CONFIG_NAND_FSL_IFC
 296 #define CONFIG_SYS_NAND_BASE            0xff800000
 297 #define CONFIG_SYS_NAND_BASE_PHYS       (0xf00000000ull | CONFIG_SYS_NAND_BASE)
 298
 299 #define CONFIG_SYS_NAND_CSPR_EXT        (0xf)
 300 #define CONFIG_SYS_NAND_CSPR    (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
 301                                 | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
 302                                 | CSPR_MSEL_NAND         /* MSEL = NAND */ \
 303                                 | CSPR_V)
 304 #define CONFIG_SYS_NAND_AMASK   IFC_AMASK(64*1024)
 305
 306 #define CONFIG_SYS_NAND_CSOR    (CSOR_NAND_ECC_ENC_EN   /* ECC on encode */ \
 307                                 | CSOR_NAND_ECC_DEC_EN  /* ECC on decode */ \
 308                                 | CSOR_NAND_ECC_MODE_4  /* 4-bit ECC */     \
 309                                 | CSOR_NAND_RAL_3       /* RAL = 2Byes */   \
 310                                 | CSOR_NAND_PGS_2K      /* Page Size = 2K */\
 311                                 | CSOR_NAND_SPRZ_64     /* Spare size = 64 */\
 312                                 | CSOR_NAND_PB(64))     /*Pages Per Block = 64*/
 313
 314 #define CONFIG_SYS_NAND_ONFI_DETECTION
 315
 316 /* ONFI NAND Flash mode0 Timing Params */
 317 #define CONFIG_SYS_NAND_FTIM0           (FTIM0_NAND_TCCST(0x07) | \
 318                                         FTIM0_NAND_TWP(0x18)    | \
 319                                         FTIM0_NAND_TWCHT(0x07)  | \
 320                                         FTIM0_NAND_TWH(0x0a))
 321 #define CONFIG_SYS_NAND_FTIM1           (FTIM1_NAND_TADLE(0x32) | \
 322                                         FTIM1_NAND_TWBE(0x39)   | \
 323                                         FTIM1_NAND_TRR(0x0e)    | \
 324                                         FTIM1_NAND_TRP(0x18))
 325 #define CONFIG_SYS_NAND_FTIM2           (FTIM2_NAND_TRAD(0x0f)  | \
 326                                         FTIM2_NAND_TREH(0x0a)   | \
 327                                         FTIM2_NAND_TWHRE(0x1e))
 328 #define CONFIG_SYS_NAND_FTIM3           0x0
 329
 330 #define CONFIG_SYS_NAND_DDR_LAW         11
 331 #define CONFIG_SYS_NAND_BASE_LIST       { CONFIG_SYS_NAND_BASE }
 332 #define CONFIG_SYS_MAX_NAND_DEVICE      1
 333 #define CONFIG_CMD_NAND
 334 #define CONFIG_SYS_NAND_BLOCK_SIZE      (512 * 1024)
 335
 336 #if defined(CONFIG_NAND)
 337 #define CONFIG_SYS_CSPR0_EXT            CONFIG_SYS_NAND_CSPR_EXT
 338 #define CONFIG_SYS_CSPR0                CONFIG_SYS_NAND_CSPR
 339 #define CONFIG_SYS_AMASK0               CONFIG_SYS_NAND_AMASK
 340 #define CONFIG_SYS_CSOR0                CONFIG_SYS_NAND_CSOR
 341 #define CONFIG_SYS_CS0_FTIM0            CONFIG_SYS_NAND_FTIM0
 342 #define CONFIG_SYS_CS0_FTIM1            CONFIG_SYS_NAND_FTIM1
 343 #define CONFIG_SYS_CS0_FTIM2            CONFIG_SYS_NAND_FTIM2
 344 #define CONFIG_SYS_CS0_FTIM3            CONFIG_SYS_NAND_FTIM3
 345 #define CONFIG_SYS_CSPR1_EXT            CONFIG_SYS_NOR0_CSPR_EXT
 346 #define CONFIG_SYS_CSPR1                CONFIG_SYS_NOR0_CSPR
 347 #define CONFIG_SYS_AMASK1               CONFIG_SYS_NOR_AMASK
 348 #define CONFIG_SYS_CSOR1                CONFIG_SYS_NOR_CSOR
 349 #define CONFIG_SYS_CS1_FTIM0            CONFIG_SYS_NOR_FTIM0
 350 #define CONFIG_SYS_CS1_FTIM1            CONFIG_SYS_NOR_FTIM1
 351 #define CONFIG_SYS_CS1_FTIM2            CONFIG_SYS_NOR_FTIM2
 352 #define CONFIG_SYS_CS1_FTIM3            CONFIG_SYS_NOR_FTIM3
 353 #else
 354 #define CONFIG_SYS_CSPR0_EXT            CONFIG_SYS_NOR0_CSPR_EXT
 355 #define CONFIG_SYS_CSPR0                CONFIG_SYS_NOR0_CSPR
 356 #define CONFIG_SYS_AMASK0               CONFIG_SYS_NOR_AMASK
 357 #define CONFIG_SYS_CSOR0                CONFIG_SYS_NOR_CSOR
 358 #define CONFIG_SYS_CS0_FTIM0            CONFIG_SYS_NOR_FTIM0
 359 #define CONFIG_SYS_CS0_FTIM1            CONFIG_SYS_NOR_FTIM1
 360 #define CONFIG_SYS_CS0_FTIM2            CONFIG_SYS_NOR_FTIM2
 361 #define CONFIG_SYS_CS0_FTIM3            CONFIG_SYS_NOR_FTIM3
 362 #define CONFIG_SYS_CSPR1_EXT            CONFIG_SYS_NAND_CSPR_EXT
 363 #define CONFIG_SYS_CSPR1                CONFIG_SYS_NAND_CSPR
 364 #define CONFIG_SYS_AMASK1               CONFIG_SYS_NAND_AMASK
 365 #define CONFIG_SYS_CSOR1                CONFIG_SYS_NAND_CSOR
 366 #define CONFIG_SYS_CS1_FTIM0            CONFIG_SYS_NAND_FTIM0
 367 #define CONFIG_SYS_CS1_FTIM1            CONFIG_SYS_NAND_FTIM1
 368 #define CONFIG_SYS_CS1_FTIM2            CONFIG_SYS_NAND_FTIM2
 369 #define CONFIG_SYS_CS1_FTIM3            CONFIG_SYS_NAND_FTIM3
 370 #endif
 371
 372 #if defined(CONFIG_RAMBOOT_PBL)
 373 #define CONFIG_SYS_RAMBOOT
 374 #endif
 375
 376 #ifdef CONFIG_SPL_BUILD
 377 #define CONFIG_SYS_MONITOR_BASE  CONFIG_SPL_TEXT_BASE
 378 #else
 379 #define CONFIG_SYS_MONITOR_BASE  CONFIG_SYS_TEXT_BASE /* start of monitor */
 380 #endif
 381
 382 #define CONFIG_BOARD_EARLY_INIT_R       /* call board_early_init_r function */
 383 #define CONFIG_MISC_INIT_R
 384 #define CONFIG_HWCONFIG
 385
 386 /* define to use L1 as initial stack */
 387 #define CONFIG_L1_INIT_RAM
 388 #define CONFIG_SYS_INIT_RAM_LOCK
 389 #define CONFIG_SYS_INIT_RAM_ADDR        0xfdd00000 /* Initial L1 address */
 390 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH      0xf
 391 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW       0xfe03c000
 392 /* The assembler doesn't like typecast */
 393 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
 394                         ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
 395                         CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
 396 #define CONFIG_SYS_INIT_RAM_SIZE        0x00004000
 397 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - \
 398                                                 GENERATED_GBL_DATA_SIZE)
 399 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 400 #define CONFIG_SYS_MONITOR_LEN          (768 * 1024)
 401 #define CONFIG_SYS_MALLOC_LEN           (4 * 1024 * 1024)
 402
 403 /*
 404  * Serial Port
 405  */
 406 #define CONFIG_CONS_INDEX               1
 407 #define CONFIG_SYS_NS16550_SERIAL
 408 #define CONFIG_SYS_NS16550_REG_SIZE     1
 409 #define CONFIG_SYS_NS16550_CLK          (get_bus_freq(0)/2)
 410 #define CONFIG_SYS_BAUDRATE_TABLE       \
 411         {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
 412 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500)
 413 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600)
 414 #define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500)
 415 #define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600)
 416
 417 /*
 418  * I2C
 419  */
 420 #define CONFIG_SYS_I2C
 421 #define CONFIG_SYS_I2C_FSL
 422 #define CONFIG_SYS_FSL_I2C_SLAVE   0x7F
 423 #define CONFIG_SYS_FSL_I2C2_SLAVE  0x7F
 424 #define CONFIG_SYS_FSL_I2C3_SLAVE  0x7F
 425 #define CONFIG_SYS_FSL_I2C4_SLAVE  0x7F
 426 #define CONFIG_SYS_FSL_I2C_OFFSET  0x118000
 427 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x118100
 428 #define CONFIG_SYS_FSL_I2C3_OFFSET 0x119000
 429 #define CONFIG_SYS_FSL_I2C4_OFFSET 0x119100
 430 #define CONFIG_SYS_FSL_I2C_SPEED   100000
 431 #define CONFIG_SYS_FSL_I2C2_SPEED  100000
 432 #define CONFIG_SYS_FSL_I2C3_SPEED  100000
 433 #define CONFIG_SYS_FSL_I2C4_SPEED  100000
 434 #define I2C_MUX_PCA_ADDR_PRI    0x77 /* I2C bus multiplexer,primary */
 435 #define I2C_MUX_PCA_ADDR_SEC1   0x75 /* I2C bus multiplexer,secondary 1 */
 436 #define I2C_MUX_PCA_ADDR_SEC2   0x76 /* I2C bus multiplexer,secondary 2 */
 437 #define I2C_MUX_CH_DEFAULT      0x8
 438
 439 #define I2C_MUX_CH_VOL_MONITOR  0xa
 440
 441 #define CONFIG_VID_FLS_ENV              "t208xrdb_vdd_mv"
 442 #ifndef CONFIG_SPL_BUILD
 443 #define CONFIG_VID
 444 #endif
 445 #define CONFIG_VOL_MONITOR_IR36021_SET
 446 #define CONFIG_VOL_MONITOR_IR36021_READ
 447 /* The lowest and highest voltage allowed for T208xRDB */
 448 #define VDD_MV_MIN                      819
 449 #define VDD_MV_MAX                      1212
 450
 451 /*
 452  * RapidIO
 453  */
 454 #define CONFIG_SYS_SRIO1_MEM_VIRT       0xa0000000
 455 #define CONFIG_SYS_SRIO1_MEM_PHYS       0xc20000000ull
 456 #define CONFIG_SYS_SRIO1_MEM_SIZE       0x10000000 /* 256M */
 457 #define CONFIG_SYS_SRIO2_MEM_VIRT       0xb0000000
 458 #define CONFIG_SYS_SRIO2_MEM_PHYS       0xc30000000ull
 459 #define CONFIG_SYS_SRIO2_MEM_SIZE       0x10000000 /* 256M */
 460 /*
 461  * for slave u-boot IMAGE instored in master memory space,
 462  * PHYS must be aligned based on the SIZE
 463  */
 464 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull
 465 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull
 466 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE     0x100000 /* 1M */
 467 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull
 468 /*
 469  * for slave UCODE and ENV instored in master memory space,
 470  * PHYS must be aligned based on the SIZE
 471  */
 472 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull
 473 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull
 474 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE    0x40000 /* 256K */
 475
 476 /* slave core release by master*/
 477 #define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4
 478 #define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */
 479
 480 /*
 481  * SRIO_PCIE_BOOT - SLAVE
 482  */
 483 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
 484 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000
 485 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \
 486                 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR)
 487 #endif
 488
 489 /*
 490  * eSPI - Enhanced SPI
 491  */
 492 #ifdef CONFIG_SPI_FLASH
 493 #define CONFIG_SPI_FLASH_BAR
 494 #define CONFIG_SF_DEFAULT_SPEED  10000000
 495 #define CONFIG_SF_DEFAULT_MODE    0
 496 #endif
 497
 498 /*
 499  * General PCI
 500  * Memory space is mapped 1-1, but I/O space must start from 0.
 501  */
 502 #define CONFIG_PCI              /* Enable PCI/PCIE */
 503 #define CONFIG_PCIE1            /* PCIE controler 1 */
 504 #define CONFIG_PCIE2            /* PCIE controler 2 */
 505 #define CONFIG_PCIE3            /* PCIE controler 3 */
 506 #define CONFIG_PCIE4            /* PCIE controler 4 */
 507 #define CONFIG_FSL_PCI_INIT     /* Use common FSL init code */
 508 #define CONFIG_SYS_PCI_64BIT    /* enable 64-bit PCI resources */
 509 /* controller 1, direct to uli, tgtid 3, Base address 20000 */
 510 #define CONFIG_SYS_PCIE1_MEM_VIRT       0x80000000
 511 #define CONFIG_SYS_PCIE1_MEM_BUS        0xe0000000
 512 #define CONFIG_SYS_PCIE1_MEM_PHYS       0xc00000000ull
 513 #define CONFIG_SYS_PCIE1_MEM_SIZE       0x20000000      /* 512M */
 514 #define CONFIG_SYS_PCIE1_IO_VIRT        0xf8000000
 515 #define CONFIG_SYS_PCIE1_IO_BUS         0x00000000
 516 #define CONFIG_SYS_PCIE1_IO_PHYS        0xff8000000ull
 517 #define CONFIG_SYS_PCIE1_IO_SIZE        0x00010000      /* 64k */
 518
 519 /* controller 2, Slot 2, tgtid 2, Base address 201000 */
 520 #define CONFIG_SYS_PCIE2_MEM_VIRT       0xa0000000
 521 #define CONFIG_SYS_PCIE2_MEM_BUS        0xe0000000
 522 #define CONFIG_SYS_PCIE2_MEM_PHYS       0xc20000000ull
 523 #define CONFIG_SYS_PCIE2_MEM_SIZE       0x10000000 /* 256M */
 524 #define CONFIG_SYS_PCIE2_IO_VIRT        0xf8010000
 525 #define CONFIG_SYS_PCIE2_IO_BUS         0x00000000
 526 #define CONFIG_SYS_PCIE2_IO_PHYS        0xff8010000ull
 527 #define CONFIG_SYS_PCIE2_IO_SIZE        0x00010000      /* 64k */
 528
 529 /* controller 3, Slot 1, tgtid 1, Base address 202000 */
 530 #define CONFIG_SYS_PCIE3_MEM_VIRT       0xb0000000
 531 #define CONFIG_SYS_PCIE3_MEM_BUS        0xe0000000
 532 #define CONFIG_SYS_PCIE3_MEM_PHYS       0xc30000000ull
 533 #define CONFIG_SYS_PCIE3_MEM_SIZE       0x10000000      /* 256M */
 534 #define CONFIG_SYS_PCIE3_IO_VIRT        0xf8020000
 535 #define CONFIG_SYS_PCIE3_IO_BUS         0x00000000
 536 #define CONFIG_SYS_PCIE3_IO_PHYS        0xff8020000ull
 537 #define CONFIG_SYS_PCIE3_IO_SIZE        0x00010000      /* 64k */
 538
 539 /* controller 4, Base address 203000 */
 540 #define CONFIG_SYS_PCIE4_MEM_VIRT       0xc0000000
 541 #define CONFIG_SYS_PCIE4_MEM_BUS        0xe0000000
 542 #define CONFIG_SYS_PCIE4_MEM_PHYS       0xc40000000ull
 543 #define CONFIG_SYS_PCIE4_MEM_SIZE       0x10000000      /* 256M */
 544 #define CONFIG_SYS_PCIE4_IO_BUS         0x00000000
 545 #define CONFIG_SYS_PCIE4_IO_PHYS        0xff8030000ull
 546 #define CONFIG_SYS_PCIE4_IO_SIZE        0x00010000      /* 64k */
 547
 548 #ifdef CONFIG_PCI
 549 #define CONFIG_PCI_INDIRECT_BRIDGE
 550 #define CONFIG_FSL_PCIE_RESET           /* need PCIe reset errata LSZ ADD */
 551 #define CONFIG_PCI_PNP          /* do pci plug-and-play */
 552 #define CONFIG_PCI_SCAN_SHOW    /* show pci devices on startup */
 553 #define CONFIG_DOS_PARTITION
 554 #endif
 555
 556 /* Qman/Bman */
 557 #ifndef CONFIG_NOBQFMAN
 558 #define CONFIG_SYS_DPAA_QBMAN           /* Support Q/Bman */
 559 #define CONFIG_SYS_BMAN_NUM_PORTALS     18
 560 #define CONFIG_SYS_BMAN_MEM_BASE        0xf4000000
 561 #define CONFIG_SYS_BMAN_MEM_PHYS        0xff4000000ull
 562 #define CONFIG_SYS_BMAN_MEM_SIZE        0x02000000
 563 #define CONFIG_SYS_BMAN_SP_CENA_SIZE    0x4000
 564 #define CONFIG_SYS_BMAN_SP_CINH_SIZE    0x1000
 565 #define CONFIG_SYS_BMAN_CENA_BASE       CONFIG_SYS_BMAN_MEM_BASE
 566 #define CONFIG_SYS_BMAN_CENA_SIZE       (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
 567 #define CONFIG_SYS_BMAN_CINH_BASE       (CONFIG_SYS_BMAN_MEM_BASE + \
 568                                         CONFIG_SYS_BMAN_CENA_SIZE)
 569 #define CONFIG_SYS_BMAN_CINH_SIZE       (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
 570 #define CONFIG_SYS_BMAN_SWP_ISDR_REG    0xE08
 571 #define CONFIG_SYS_QMAN_NUM_PORTALS     18
 572 #define CONFIG_SYS_QMAN_MEM_BASE        0xf6000000
 573 #define CONFIG_SYS_QMAN_MEM_PHYS        0xff6000000ull
 574 #define CONFIG_SYS_QMAN_MEM_SIZE        0x02000000
 575 #define CONFIG_SYS_QMAN_SP_CENA_SIZE    0x4000
 576 #define CONFIG_SYS_QMAN_SP_CINH_SIZE    0x1000
 577 #define CONFIG_SYS_QMAN_CENA_BASE       CONFIG_SYS_QMAN_MEM_BASE
 578 #define CONFIG_SYS_QMAN_CENA_SIZE       (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
 579 #define CONFIG_SYS_QMAN_CINH_BASE       (CONFIG_SYS_QMAN_MEM_BASE + \
 580                                         CONFIG_SYS_QMAN_CENA_SIZE)
 581 #define CONFIG_SYS_QMAN_CINH_SIZE       (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
 582 #define CONFIG_SYS_QMAN_SWP_ISDR_REG    0xE08
 583
 584 #define CONFIG_SYS_DPAA_FMAN
 585 #define CONFIG_SYS_DPAA_PME
 586 #define CONFIG_SYS_PMAN
 587 #define CONFIG_SYS_DPAA_DCE
 588 #define CONFIG_SYS_DPAA_RMAN            /* RMan */
 589 #define CONFIG_SYS_INTERLAKEN
 590
 591 /* Default address of microcode for the Linux Fman driver */
 592 #if defined(CONFIG_SPIFLASH)
 593 /*
 594  * env is stored at 0x100000, sector size is 0x10000, ucode is stored after
 595  * env, so we got 0x110000.
 596  */
 597 #define CONFIG_SYS_QE_FW_IN_SPIFLASH
 598 #define CONFIG_SYS_CORTINA_FW_IN_SPIFLASH
 599 #define CONFIG_SYS_FMAN_FW_ADDR         0x110000
 600 #define CONFIG_CORTINA_FW_ADDR          0x120000
 601
 602 #elif defined(CONFIG_SDCARD)
 603 /*
 604  * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
 605  * about 1MB (2048 blocks), Env is stored after the image, and the env size is
 606  * 0x2000 (16 blocks), 8 + 2048 + 16 = 2072, enlarge it to 2080.
 607  */
 608 #define CONFIG_SYS_QE_FMAN_FW_IN_MMC
 609 #define CONFIG_SYS_CORTINA_FW_IN_MMC
 610 #define CONFIG_SYS_FMAN_FW_ADDR         (512 * 0x820)
 611 #define CONFIG_CORTINA_FW_ADDR          (512 * 0x8a0)
 612
 613 #elif defined(CONFIG_NAND)
 614 #define CONFIG_SYS_QE_FMAN_FW_IN_NAND
 615 #define CONFIG_SYS_CORTINA_FW_IN_NAND
 616 #define CONFIG_SYS_FMAN_FW_ADDR         (3 * CONFIG_SYS_NAND_BLOCK_SIZE)
 617 #define CONFIG_CORTINA_FW_ADDR          (4 * CONFIG_SYS_NAND_BLOCK_SIZE)
 618 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
 619 /*
 620  * Slave has no ucode locally, it can fetch this from remote. When implementing
 621  * in two corenet boards, slave's ucode could be stored in master's memory
 622  * space, the address can be mapped from slave TLB->slave LAW->
 623  * slave SRIO or PCIE outbound window->master inbound window->
 624  * master LAW->the ucode address in master's memory space.
 625  */
 626 #define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE
 627 #define CONFIG_SYS_CORTINA_FW_IN_REMOTE
 628 #define CONFIG_SYS_FMAN_FW_ADDR         0xFFE00000
 629 #define CONFIG_CORTINA_FW_ADDR          0xFFE10000
 630 #else
 631 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR
 632 #define CONFIG_SYS_CORTINA_FW_IN_NOR
 633 #define CONFIG_SYS_FMAN_FW_ADDR         0xEFF00000
 634 #define CONFIG_CORTINA_FW_ADDR          0xEFE00000
 635 #endif
 636 #define CONFIG_SYS_QE_FMAN_FW_LENGTH    0x10000
 637 #define CONFIG_SYS_FDT_PAD              (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
 638 #endif /* CONFIG_NOBQFMAN */
 639
 640 #ifdef CONFIG_SYS_DPAA_FMAN
 641 #define CONFIG_FMAN_ENET
 642 #define CONFIG_PHYLIB_10G
 643 #define CONFIG_PHY_AQUANTIA
 644 #define CONFIG_PHY_CORTINA
 645 #define CONFIG_PHY_REALTEK
 646 #define CONFIG_CORTINA_FW_LENGTH        0x40000
 647 #define RGMII_PHY1_ADDR         0x01  /* RealTek RTL8211E */
 648 #define RGMII_PHY2_ADDR         0x02
 649 #define CORTINA_PHY_ADDR1       0x0c  /* Cortina CS4315 */
 650 #define CORTINA_PHY_ADDR2       0x0d
 651 #define FM1_10GEC3_PHY_ADDR     0x00  /* Aquantia AQ1202 10G Base-T */
 652 #define FM1_10GEC4_PHY_ADDR     0x01
 653 #endif
 654
 655 #ifdef CONFIG_FMAN_ENET
 656 #define CONFIG_MII              /* MII PHY management */
 657 #define CONFIG_ETHPRIME         "FM1@DTSEC3"
 658 #define CONFIG_PHY_GIGE         /* Include GbE speed/duplex detection */
 659 #endif
 660
 661 /*
 662  * SATA
 663  */
 664 #ifdef CONFIG_FSL_SATA_V2
 665 #define CONFIG_LIBATA
 666 #define CONFIG_FSL_SATA
 667 #define CONFIG_SYS_SATA_MAX_DEVICE      2
 668 #define CONFIG_SATA1
 669 #define CONFIG_SYS_SATA1                CONFIG_SYS_MPC85xx_SATA1_ADDR
 670 #define CONFIG_SYS_SATA1_FLAGS          FLAGS_DMA
 671 #define CONFIG_SATA2
 672 #define CONFIG_SYS_SATA2                CONFIG_SYS_MPC85xx_SATA2_ADDR
 673 #define CONFIG_SYS_SATA2_FLAGS          FLAGS_DMA
 674 #define CONFIG_LBA48
 675 #define CONFIG_CMD_SATA
 676 #define CONFIG_DOS_PARTITION
 677 #endif
 678
 679 /*
 680  * USB
 681  */
 682 #ifdef CONFIG_USB_EHCI
 683 #define CONFIG_USB_STORAGE
 684 #define CONFIG_USB_EHCI_FSL
 685 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 686 #define CONFIG_HAS_FSL_DR_USB
 687 #endif
 688
 689 /*
 690  * SDHC
 691  */
 692 #ifdef CONFIG_MMC
 693 #define CONFIG_FSL_ESDHC
 694 #define CONFIG_SYS_FSL_ESDHC_ADDR       CONFIG_SYS_MPC85xx_ESDHC_ADDR
 695 #define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT
 696 #define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
 697 #define CONFIG_GENERIC_MMC
 698 #define CONFIG_DOS_PARTITION
 699 #endif
 700
 701 /*
 702  * Dynamic MTD Partition support with mtdparts
 703  */
 704 #ifndef CONFIG_SYS_NO_FLASH
 705 #define CONFIG_MTD_DEVICE
 706 #define CONFIG_MTD_PARTITIONS
 707 #define CONFIG_CMD_MTDPARTS
 708 #define CONFIG_FLASH_CFI_MTD
 709 #define MTDIDS_DEFAULT "nor0=fe8000000.nor,nand0=fff800000.flash," \
 710                         "spi0=spife110000.1"
 711 #define MTDPARTS_DEFAULT "mtdparts=fe8000000.nor:1m(uboot),5m(kernel)," \
 712                         "128k(dtb),96m(fs),-(user);fff800000.flash:1m(uboot)," \
 713                         "5m(kernel),128k(dtb),96m(fs),-(user);spife110000.1:" \
 714                         "1m(uboot),5m(kernel),128k(dtb),-(user)"
 715 #endif
 716
 717 /*
 718  * Environment
 719  */
 720
 721 /*
 722  * Command line configuration.
 723  */
 724 #define CONFIG_CMD_ERRATA
 725 #define CONFIG_CMD_REGINFO
 726
 727 #ifdef CONFIG_PCI
 728 #define CONFIG_CMD_PCI
 729 #endif
 730
 731 /* Hash command with SHA acceleration supported in hardware */
 732 #ifdef CONFIG_FSL_CAAM
 733 #define CONFIG_CMD_HASH
 734 #define CONFIG_SHA_HW_ACCEL
 735 #endif
 736
 737 /*
 738  * Miscellaneous configurable options
 739  */
 740 #define CONFIG_SYS_LONGHELP             /* undef to save memory */
 741 #define CONFIG_CMDLINE_EDITING          /* Command-line editing */
 742 #define CONFIG_AUTO_COMPLETE            /* add autocompletion support */
 743 #define CONFIG_SYS_LOAD_ADDR    0x2000000 /* default load address */
 744 #ifdef CONFIG_CMD_KGDB
 745 #define CONFIG_SYS_CBSIZE       1024      /* Console I/O Buffer Size */
 746 #else
 747 #define CONFIG_SYS_CBSIZE       256       /* Console I/O Buffer Size */
 748 #endif
 749 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
 750 #define CONFIG_SYS_MAXARGS      16      /* max number of command args */
 751 #define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */
 752
 753 /*
 754  * For booting Linux, the board info and command line data
 755  * have to be in the first 64 MB of memory, since this is
 756  * the maximum mapped by the Linux kernel during initialization.
 757  */
 758 #define CONFIG_SYS_BOOTMAPSZ    (64 << 20)      /* Initial map for Linux*/
 759 #define CONFIG_SYS_BOOTM_LEN    (64 << 20)      /* Increase max gunzip size */
 760
 761 #ifdef CONFIG_CMD_KGDB
 762 #define CONFIG_KGDB_BAUDRATE    230400  /* speed to run kgdb serial port */
 763 #define CONFIG_KGDB_SER_INDEX   2       /* which serial port to use */
 764 #endif
 765
 766 /*
 767  * Environment Configuration
 768  */
 769 #define CONFIG_ROOTPATH  "/opt/nfsroot"
 770 #define CONFIG_BOOTFILE  "uImage"
 771 #define CONFIG_UBOOTPATH "u-boot.bin"   /* U-Boot image on TFTP server */
 772
 773 /* default location for tftp and bootm */
 774 #define CONFIG_LOADADDR         1000000
 775 #define CONFIG_BAUDRATE         115200
 776 #define CONFIG_BOOTDELAY        10      /* -1 disables auto-boot */
 777 #define __USB_PHY_TYPE          utmi
 778
 779 #define CONFIG_EXTRA_ENV_SETTINGS                               \
 780         "hwconfig=fsl_ddr:"                                     \
 781         "ctlr_intlv=" __stringify(CTRL_INTLV_PREFERED) ","      \
 782         "bank_intlv=auto;"                                      \
 783         "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\
 784         "netdev=eth0\0"                                         \
 785         "uboot=" __stringify(CONFIG_UBOOTPATH) "\0"             \
 786         "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0"     \
 787         "tftpflash=tftpboot $loadaddr $uboot && "               \
 788         "protect off $ubootaddr +$filesize && "                 \
 789         "erase $ubootaddr +$filesize && "                       \
 790         "cp.b $loadaddr $ubootaddr $filesize && "               \
 791         "protect on $ubootaddr +$filesize && "                  \
 792         "cmp.b $loadaddr $ubootaddr $filesize\0"                \
 793         "consoledev=ttyS0\0"                                    \
 794         "ramdiskaddr=2000000\0"                                 \
 795         "ramdiskfile=t2080rdb/ramdisk.uboot\0"                  \
 796         "fdtaddr=c00000\0"                                      \
 797         "fdtfile=t2080rdb/t2080rdb.dtb\0"                       \
 798         "bdev=sda3\0"
 799
 800 /*
 801  * For emulation this causes u-boot to jump to the start of the
 802  * proof point app code automatically
 803  */
 804 #define CONFIG_PROOF_POINTS                             \
 805         "setenv bootargs root=/dev/$bdev rw "           \
 806         "console=$consoledev,$baudrate $othbootargs;"   \
 807         "cpu 1 release 0x29000000 - - -;"               \
 808         "cpu 2 release 0x29000000 - - -;"               \
 809         "cpu 3 release 0x29000000 - - -;"               \
 810         "cpu 4 release 0x29000000 - - -;"               \
 811         "cpu 5 release 0x29000000 - - -;"               \
 812         "cpu 6 release 0x29000000 - - -;"               \
 813         "cpu 7 release 0x29000000 - - -;"               \
 814         "go 0x29000000"
 815
 816 #define CONFIG_HVBOOT                           \
 817         "setenv bootargs config-addr=0x60000000; "      \
 818         "bootm 0x01000000 - 0x00f00000"
 819
 820 #define CONFIG_ALU                              \
 821         "setenv bootargs root=/dev/$bdev rw "           \
 822         "console=$consoledev,$baudrate $othbootargs;"   \
 823         "cpu 1 release 0x01000000 - - -;"               \
 824         "cpu 2 release 0x01000000 - - -;"               \
 825         "cpu 3 release 0x01000000 - - -;"               \
 826         "cpu 4 release 0x01000000 - - -;"               \
 827         "cpu 5 release 0x01000000 - - -;"               \
 828         "cpu 6 release 0x01000000 - - -;"               \
 829         "cpu 7 release 0x01000000 - - -;"               \
 830         "go 0x01000000"
 831
 832 #define CONFIG_LINUX                            \
 833         "setenv bootargs root=/dev/ram rw "             \
 834         "console=$consoledev,$baudrate $othbootargs;"   \
 835         "setenv ramdiskaddr 0x02000000;"                \
 836         "setenv fdtaddr 0x00c00000;"                    \
 837         "setenv loadaddr 0x1000000;"                    \
 838         "bootm $loadaddr $ramdiskaddr $fdtaddr"
 839
 840 #define CONFIG_HDBOOT                                   \
 841         "setenv bootargs root=/dev/$bdev rw "           \
 842         "console=$consoledev,$baudrate $othbootargs;"   \
 843         "tftp $loadaddr $bootfile;"                     \
 844         "tftp $fdtaddr $fdtfile;"                       \
 845         "bootm $loadaddr - $fdtaddr"
 846
 847 #define CONFIG_NFSBOOTCOMMAND                   \
 848         "setenv bootargs root=/dev/nfs rw "     \
 849         "nfsroot=$serverip:$rootpath "          \
 850         "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
 851         "console=$consoledev,$baudrate $othbootargs;"   \
 852         "tftp $loadaddr $bootfile;"             \
 853         "tftp $fdtaddr $fdtfile;"               \
 854         "bootm $loadaddr - $fdtaddr"
 855
 856 #define CONFIG_RAMBOOTCOMMAND                           \
 857         "setenv bootargs root=/dev/ram rw "             \
 858         "console=$consoledev,$baudrate $othbootargs;"   \
 859         "tftp $ramdiskaddr $ramdiskfile;"               \
 860         "tftp $loadaddr $bootfile;"                     \
 861         "tftp $fdtaddr $fdtfile;"                       \
 862         "bootm $loadaddr $ramdiskaddr $fdtaddr"
 863
 864 #define CONFIG_BOOTCOMMAND              CONFIG_LINUX
 865
 866 #include <asm/fsl_secure_boot.h>
 867
 868 #endif  /* __T2080RDB_H */