include/configs/T208xQDS.h

   1 /* SPDX-License-Identifier: GPL-2.0+ */
   2 /*
   3  * Copyright 2011-2013 Freescale Semiconductor, Inc.
   4  * Copyright 2020-2021 NXP
   5  */
   6
   7 /*
   8  * T2080/T2081 QDS board configuration file
   9  */
  10
  11 #ifndef __T208xQDS_H
  12 #define __T208xQDS_H
  13
  14 #include <linux/stringify.h>
  15
  16 #define CONFIG_ICS307_REFCLK_HZ 25000000  /* ICS307 ref clk freq */
  17 #if defined(CONFIG_ARCH_T2080)
  18 #define CONFIG_FSL_SATA_V2
  19 #define CONFIG_SYS_SRIO         /* Enable Serial RapidIO Support */
  20 #define CONFIG_SRIO1            /* SRIO port 1 */
  21 #define CONFIG_SRIO2            /* SRIO port 2 */
  22 #endif
  23
  24 /* High Level Configuration Options */
  25 #define CONFIG_SYS_BOOK3E_HV    /* Category E.HV supported */
  26 #define CONFIG_ENABLE_36BIT_PHYS
  27
  28 #define CONFIG_SYS_FSL_CPC      /* Corenet Platform Cache */
  29 #define CONFIG_SYS_NUM_CPC      CONFIG_SYS_NUM_DDR_CTLRS
  30
  31 #ifdef CONFIG_RAMBOOT_PBL
  32 #define CONFIG_SYS_FSL_PBL_PBI board/freescale/t208xqds/t208x_pbi.cfg
  33
  34 #define CONFIG_SPL_FLUSH_IMAGE
  35 #define CONFIG_SPL_PAD_TO               0x40000
  36 #define CONFIG_SPL_MAX_SIZE             0x28000
  37 #define RESET_VECTOR_OFFSET             0x27FFC
  38 #define BOOT_PAGE_OFFSET                0x27000
  39 #ifdef CONFIG_SPL_BUILD
  40 #define CONFIG_SPL_SKIP_RELOCATE
  41 #define CONFIG_SPL_COMMON_INIT_DDR
  42 #define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
  43 #endif
  44
  45 #ifdef CONFIG_MTD_RAW_NAND
  46 #define CONFIG_SYS_NAND_U_BOOT_SIZE     (768 << 10)
  47 #define CONFIG_SYS_NAND_U_BOOT_DST      0x00200000
  48 #define CONFIG_SYS_NAND_U_BOOT_START    0x00200000
  49 #define CONFIG_SYS_NAND_U_BOOT_OFFS     (256 << 10)
  50 #if defined(CONFIG_ARCH_T2080)
  51 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xqds/t2080_nand_rcw.cfg
  52 #endif
  53 #endif
  54
  55 #ifdef CONFIG_SPIFLASH
  56 #define CONFIG_RESET_VECTOR_ADDRESS             0x200FFC
  57 #define CONFIG_SPL_SPI_FLASH_MINIMAL
  58 #define CONFIG_SYS_SPI_FLASH_U_BOOT_SIZE        (768 << 10)
  59 #define CONFIG_SYS_SPI_FLASH_U_BOOT_DST         (0x00200000)
  60 #define CONFIG_SYS_SPI_FLASH_U_BOOT_START       (0x00200000)
  61 #define CONFIG_SYS_SPI_FLASH_U_BOOT_OFFS        (256 << 10)
  62 #ifndef CONFIG_SPL_BUILD
  63 #define CONFIG_SYS_MPC85XX_NO_RESETVEC
  64 #endif
  65 #if defined(CONFIG_ARCH_T2080)
  66 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xqds/t2080_spi_rcw.cfg
  67 #endif
  68 #endif
  69
  70 #ifdef CONFIG_SDCARD
  71 #define CONFIG_RESET_VECTOR_ADDRESS             0x200FFC
  72 #define CONFIG_SYS_MMC_U_BOOT_SIZE      (768 << 10)
  73 #define CONFIG_SYS_MMC_U_BOOT_DST       (0x00200000)
  74 #define CONFIG_SYS_MMC_U_BOOT_START     (0x00200000)
  75 #define CONFIG_SYS_MMC_U_BOOT_OFFS      (260 << 10)
  76 #ifndef CONFIG_SPL_BUILD
  77 #define CONFIG_SYS_MPC85XX_NO_RESETVEC
  78 #endif
  79 #if defined(CONFIG_ARCH_T2080)
  80 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xqds/t2080_sd_rcw.cfg
  81 #endif
  82 #endif
  83
  84 #endif /* CONFIG_RAMBOOT_PBL */
  85
  86 #define CONFIG_SRIO_PCIE_BOOT_MASTER
  87 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
  88 /* Set 1M boot space */
  89 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000)
  90 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \
  91                 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR)
  92 #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
  93 #endif
  94
  95 #ifndef CONFIG_RESET_VECTOR_ADDRESS
  96 #define CONFIG_RESET_VECTOR_ADDRESS     0xeffffffc
  97 #endif
  98
  99 /*
 100  * These can be toggled for performance analysis, otherwise use default.
 101  */
 102 #define CONFIG_SYS_CACHE_STASHING
 103 #define CONFIG_BTB              /* toggle branch predition */
 104 #define CONFIG_DDR_ECC
 105 #ifdef CONFIG_DDR_ECC
 106 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
 107 #define CONFIG_MEM_INIT_VALUE           0xdeadbeef
 108 #endif
 109
 110 #ifndef __ASSEMBLY__
 111 unsigned long get_board_sys_clk(void);
 112 unsigned long get_board_ddr_clk(void);
 113 #endif
 114
 115 #define CONFIG_SYS_CLK_FREQ     get_board_sys_clk()
 116 #define CONFIG_DDR_CLK_FREQ     get_board_ddr_clk()
 117
 118 /*
 119  * Config the L3 Cache as L3 SRAM
 120  */
 121 #define CONFIG_SYS_INIT_L3_ADDR         0xFFFC0000
 122 #define CONFIG_SYS_L3_SIZE              (512 << 10)
 123 #define CONFIG_SPL_GD_ADDR              (CONFIG_SYS_INIT_L3_ADDR + 32 * 1024)
 124 #define SPL_ENV_ADDR                    (CONFIG_SPL_GD_ADDR + 4 * 1024)
 125 #define CONFIG_SPL_RELOC_MALLOC_ADDR    (CONFIG_SPL_GD_ADDR + 12 * 1024)
 126 #define CONFIG_SPL_RELOC_MALLOC_SIZE    (50 << 10)
 127 #define CONFIG_SPL_RELOC_STACK          (CONFIG_SPL_GD_ADDR + 64 * 1024)
 128
 129 #define CONFIG_SYS_DCSRBAR      0xf0000000
 130 #define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull
 131
 132 /* EEPROM */
 133 #define CONFIG_SYS_I2C_EEPROM_NXID
 134 #define CONFIG_SYS_EEPROM_BUS_NUM       0
 135 #define CONFIG_SYS_I2C_EEPROM_ADDR      0x57
 136 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN  1
 137
 138 /*
 139  * DDR Setup
 140  */
 141 #define CONFIG_VERY_BIG_RAM
 142 #define CONFIG_SYS_DDR_SDRAM_BASE       0x00000000
 143 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE
 144 #define CONFIG_DIMM_SLOTS_PER_CTLR      2
 145 #define CONFIG_CHIP_SELECTS_PER_CTRL    (2 * CONFIG_DIMM_SLOTS_PER_CTLR)
 146 #define CONFIG_DDR_SPD
 147 #define CONFIG_SYS_SPD_BUS_NUM  0
 148 #define CONFIG_SYS_SDRAM_SIZE   2048    /* for fixed parameter use */
 149 #define SPD_EEPROM_ADDRESS1     0x51
 150 #define SPD_EEPROM_ADDRESS2     0x52
 151 #define SPD_EEPROM_ADDRESS      SPD_EEPROM_ADDRESS1
 152 #define CTRL_INTLV_PREFERED     cacheline
 153
 154 /*
 155  * IFC Definitions
 156  */
 157 #define CONFIG_SYS_FLASH_BASE           0xe0000000
 158 #define CONFIG_SYS_FLASH_BASE_PHYS      (0xf00000000ull | CONFIG_SYS_FLASH_BASE)
 159 #define CONFIG_SYS_NOR0_CSPR_EXT        (0xf)
 160 #define CONFIG_SYS_NOR0_CSPR    (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS \
 161                                 + 0x8000000) | \
 162                                 CSPR_PORT_SIZE_16 | \
 163                                 CSPR_MSEL_NOR | \
 164                                 CSPR_V)
 165 #define CONFIG_SYS_NOR1_CSPR_EXT        (0xf)
 166 #define CONFIG_SYS_NOR1_CSPR    (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
 167                                 CSPR_PORT_SIZE_16 | \
 168                                 CSPR_MSEL_NOR | \
 169                                 CSPR_V)
 170 #define CONFIG_SYS_NOR_AMASK    IFC_AMASK(128*1024*1024)
 171 /* NOR Flash Timing Params */
 172 #define CONFIG_SYS_NOR_CSOR     CSOR_NAND_TRHZ_80
 173
 174 #define CONFIG_SYS_NOR_FTIM0    (FTIM0_NOR_TACSE(0x4) | \
 175                                 FTIM0_NOR_TEADC(0x5) | \
 176                                 FTIM0_NOR_TEAHC(0x5))
 177 #define CONFIG_SYS_NOR_FTIM1    (FTIM1_NOR_TACO(0x35) | \
 178                                 FTIM1_NOR_TRAD_NOR(0x1A) |\
 179                                 FTIM1_NOR_TSEQRAD_NOR(0x13))
 180 #define CONFIG_SYS_NOR_FTIM2    (FTIM2_NOR_TCS(0x4) | \
 181                                 FTIM2_NOR_TCH(0x4) | \
 182                                 FTIM2_NOR_TWPH(0x0E) | \
 183                                 FTIM2_NOR_TWP(0x1c))
 184 #define CONFIG_SYS_NOR_FTIM3    0x0
 185
 186 #define CONFIG_SYS_FLASH_QUIET_TEST
 187 #define CONFIG_FLASH_SHOW_PROGRESS      45 /* count down from 45/5: 9..1 */
 188
 189 #define CONFIG_SYS_MAX_FLASH_BANKS      2       /* number of banks */
 190 #define CONFIG_SYS_MAX_FLASH_SECT       1024    /* sectors per device */
 191 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000   /* Flash Erase Timeout (ms) */
 192 #define CONFIG_SYS_FLASH_WRITE_TOUT     500     /* Flash Write Timeout (ms) */
 193
 194 #define CONFIG_SYS_FLASH_EMPTY_INFO
 195 #define CONFIG_SYS_FLASH_BANKS_LIST     {CONFIG_SYS_FLASH_BASE_PHYS \
 196                                         + 0x8000000, CONFIG_SYS_FLASH_BASE_PHYS}
 197
 198 #define CONFIG_FSL_QIXIS        /* use common QIXIS code */
 199 #define QIXIS_BASE                      0xffdf0000
 200 #define QIXIS_LBMAP_SWITCH              6
 201 #define QIXIS_LBMAP_MASK                0x0f
 202 #define QIXIS_LBMAP_SHIFT               0
 203 #define QIXIS_LBMAP_DFLTBANK            0x00
 204 #define QIXIS_LBMAP_ALTBANK             0x04
 205 #define QIXIS_LBMAP_NAND                0x09
 206 #define QIXIS_LBMAP_SD                  0x00
 207 #define QIXIS_RCW_SRC_NAND              0x104
 208 #define QIXIS_RCW_SRC_SD                0x040
 209 #define QIXIS_RST_CTL_RESET             0x83
 210 #define QIXIS_RST_FORCE_MEM             0x1
 211 #define QIXIS_RCFG_CTL_RECONFIG_IDLE    0x20
 212 #define QIXIS_RCFG_CTL_RECONFIG_START   0x21
 213 #define QIXIS_RCFG_CTL_WATCHDOG_ENBLE   0x08
 214 #define QIXIS_BASE_PHYS         (0xf00000000ull | QIXIS_BASE)
 215
 216 #define CONFIG_SYS_CSPR3_EXT    (0xf)
 217 #define CONFIG_SYS_CSPR3        (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \
 218                                 | CSPR_PORT_SIZE_8 \
 219                                 | CSPR_MSEL_GPCM \
 220                                 | CSPR_V)
 221 #define CONFIG_SYS_AMASK3       IFC_AMASK(64 * 1024)
 222 #define CONFIG_SYS_CSOR3        0x0
 223 /* QIXIS Timing parameters for IFC CS3 */
 224 #define CONFIG_SYS_CS3_FTIM0            (FTIM0_GPCM_TACSE(0x0e) | \
 225                                         FTIM0_GPCM_TEADC(0x0e) | \
 226                                         FTIM0_GPCM_TEAHC(0x0e))
 227 #define CONFIG_SYS_CS3_FTIM1            (FTIM1_GPCM_TACO(0xff) | \
 228                                         FTIM1_GPCM_TRAD(0x3f))
 229 #define CONFIG_SYS_CS3_FTIM2            (FTIM2_GPCM_TCS(0x0e) | \
 230                                         FTIM2_GPCM_TCH(0x8) | \
 231                                         FTIM2_GPCM_TWP(0x1f))
 232 #define CONFIG_SYS_CS3_FTIM3            0x0
 233
 234 /* NAND Flash on IFC */
 235 #define CONFIG_NAND_FSL_IFC
 236 #define CONFIG_SYS_NAND_BASE            0xff800000
 237 #define CONFIG_SYS_NAND_BASE_PHYS       (0xf00000000ull | CONFIG_SYS_NAND_BASE)
 238
 239 #define CONFIG_SYS_NAND_CSPR_EXT        (0xf)
 240 #define CONFIG_SYS_NAND_CSPR    (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
 241                                 | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
 242                                 | CSPR_MSEL_NAND         /* MSEL = NAND */ \
 243                                 | CSPR_V)
 244 #define CONFIG_SYS_NAND_AMASK   IFC_AMASK(64*1024)
 245
 246 #define CONFIG_SYS_NAND_CSOR    (CSOR_NAND_ECC_ENC_EN   /* ECC on encode */ \
 247                                 | CSOR_NAND_ECC_DEC_EN  /* ECC on decode */ \
 248                                 | CSOR_NAND_ECC_MODE_4  /* 4-bit ECC */     \
 249                                 | CSOR_NAND_RAL_3       /* RAL = 2Byes */   \
 250                                 | CSOR_NAND_PGS_2K      /* Page Size = 2K */\
 251                                 | CSOR_NAND_SPRZ_64     /* Spare size = 64 */\
 252                                 | CSOR_NAND_PB(64))     /*Pages Per Block = 64*/
 253
 254 #define CONFIG_SYS_NAND_ONFI_DETECTION
 255
 256 /* ONFI NAND Flash mode0 Timing Params */
 257 #define CONFIG_SYS_NAND_FTIM0           (FTIM0_NAND_TCCST(0x07) | \
 258                                         FTIM0_NAND_TWP(0x18)    | \
 259                                         FTIM0_NAND_TWCHT(0x07)  | \
 260                                         FTIM0_NAND_TWH(0x0a))
 261 #define CONFIG_SYS_NAND_FTIM1           (FTIM1_NAND_TADLE(0x32) | \
 262                                         FTIM1_NAND_TWBE(0x39)   | \
 263                                         FTIM1_NAND_TRR(0x0e)    | \
 264                                         FTIM1_NAND_TRP(0x18))
 265 #define CONFIG_SYS_NAND_FTIM2           (FTIM2_NAND_TRAD(0x0f)  | \
 266                                         FTIM2_NAND_TREH(0x0a)   | \
 267                                         FTIM2_NAND_TWHRE(0x1e))
 268 #define CONFIG_SYS_NAND_FTIM3           0x0
 269
 270 #define CONFIG_SYS_NAND_DDR_LAW         11
 271 #define CONFIG_SYS_NAND_BASE_LIST       { CONFIG_SYS_NAND_BASE }
 272 #define CONFIG_SYS_MAX_NAND_DEVICE      1
 273 #define CONFIG_SYS_NAND_BLOCK_SIZE      (128 * 1024)
 274
 275 #if defined(CONFIG_MTD_RAW_NAND)
 276 #define CONFIG_SYS_CSPR0_EXT            CONFIG_SYS_NAND_CSPR_EXT
 277 #define CONFIG_SYS_CSPR0                CONFIG_SYS_NAND_CSPR
 278 #define CONFIG_SYS_AMASK0               CONFIG_SYS_NAND_AMASK
 279 #define CONFIG_SYS_CSOR0                CONFIG_SYS_NAND_CSOR
 280 #define CONFIG_SYS_CS0_FTIM0            CONFIG_SYS_NAND_FTIM0
 281 #define CONFIG_SYS_CS0_FTIM1            CONFIG_SYS_NAND_FTIM1
 282 #define CONFIG_SYS_CS0_FTIM2            CONFIG_SYS_NAND_FTIM2
 283 #define CONFIG_SYS_CS0_FTIM3            CONFIG_SYS_NAND_FTIM3
 284 #define CONFIG_SYS_CSPR1_EXT            CONFIG_SYS_NOR0_CSPR_EXT
 285 #define CONFIG_SYS_CSPR1                CONFIG_SYS_NOR0_CSPR
 286 #define CONFIG_SYS_AMASK1               CONFIG_SYS_NOR_AMASK
 287 #define CONFIG_SYS_CSOR1                CONFIG_SYS_NOR_CSOR
 288 #define CONFIG_SYS_CS1_FTIM0            CONFIG_SYS_NOR_FTIM0
 289 #define CONFIG_SYS_CS1_FTIM1            CONFIG_SYS_NOR_FTIM1
 290 #define CONFIG_SYS_CS1_FTIM2            CONFIG_SYS_NOR_FTIM2
 291 #define CONFIG_SYS_CS1_FTIM3            CONFIG_SYS_NOR_FTIM3
 292 #define CONFIG_SYS_CSPR2_EXT            CONFIG_SYS_NOR1_CSPR_EXT
 293 #define CONFIG_SYS_CSPR2                CONFIG_SYS_NOR1_CSPR
 294 #define CONFIG_SYS_AMASK2               CONFIG_SYS_NOR_AMASK
 295 #define CONFIG_SYS_CSOR2                CONFIG_SYS_NOR_CSOR
 296 #define CONFIG_SYS_CS2_FTIM0            CONFIG_SYS_NOR_FTIM0
 297 #define CONFIG_SYS_CS2_FTIM1            CONFIG_SYS_NOR_FTIM1
 298 #define CONFIG_SYS_CS2_FTIM2            CONFIG_SYS_NOR_FTIM2
 299 #define CONFIG_SYS_CS2_FTIM3            CONFIG_SYS_NOR_FTIM3
 300 #else
 301 #define CONFIG_SYS_CSPR0_EXT            CONFIG_SYS_NOR0_CSPR_EXT
 302 #define CONFIG_SYS_CSPR0                CONFIG_SYS_NOR0_CSPR
 303 #define CONFIG_SYS_AMASK0               CONFIG_SYS_NOR_AMASK
 304 #define CONFIG_SYS_CSOR0                CONFIG_SYS_NOR_CSOR
 305 #define CONFIG_SYS_CS0_FTIM0            CONFIG_SYS_NOR_FTIM0
 306 #define CONFIG_SYS_CS0_FTIM1            CONFIG_SYS_NOR_FTIM1
 307 #define CONFIG_SYS_CS0_FTIM2            CONFIG_SYS_NOR_FTIM2
 308 #define CONFIG_SYS_CS0_FTIM3            CONFIG_SYS_NOR_FTIM3
 309 #define CONFIG_SYS_CSPR1_EXT            CONFIG_SYS_NOR1_CSPR_EXT
 310 #define CONFIG_SYS_CSPR1                CONFIG_SYS_NOR1_CSPR
 311 #define CONFIG_SYS_AMASK1               CONFIG_SYS_NOR_AMASK
 312 #define CONFIG_SYS_CSOR1                CONFIG_SYS_NOR_CSOR
 313 #define CONFIG_SYS_CS1_FTIM0            CONFIG_SYS_NOR_FTIM0
 314 #define CONFIG_SYS_CS1_FTIM1            CONFIG_SYS_NOR_FTIM1
 315 #define CONFIG_SYS_CS1_FTIM2            CONFIG_SYS_NOR_FTIM2
 316 #define CONFIG_SYS_CS1_FTIM3            CONFIG_SYS_NOR_FTIM3
 317 #define CONFIG_SYS_CSPR2_EXT            CONFIG_SYS_NAND_CSPR_EXT
 318 #define CONFIG_SYS_CSPR2                CONFIG_SYS_NAND_CSPR
 319 #define CONFIG_SYS_AMASK2               CONFIG_SYS_NAND_AMASK
 320 #define CONFIG_SYS_CSOR2                CONFIG_SYS_NAND_CSOR
 321 #define CONFIG_SYS_CS2_FTIM0            CONFIG_SYS_NAND_FTIM0
 322 #define CONFIG_SYS_CS2_FTIM1            CONFIG_SYS_NAND_FTIM1
 323 #define CONFIG_SYS_CS2_FTIM2            CONFIG_SYS_NAND_FTIM2
 324 #define CONFIG_SYS_CS2_FTIM3            CONFIG_SYS_NAND_FTIM3
 325 #endif
 326
 327 #if defined(CONFIG_RAMBOOT_PBL)
 328 #define CONFIG_SYS_RAMBOOT
 329 #endif
 330
 331 #ifdef CONFIG_SPL_BUILD
 332 #define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE
 333 #else
 334 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE    /* start of monitor */
 335 #endif
 336
 337 #define CONFIG_HWCONFIG
 338
 339 /* define to use L1 as initial stack */
 340 #define CONFIG_L1_INIT_RAM
 341 #define CONFIG_SYS_INIT_RAM_LOCK
 342 #define CONFIG_SYS_INIT_RAM_ADDR        0xfdd00000 /* Initial L1 address */
 343 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH      0xf
 344 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW       0xfe03c000
 345 /* The assembler doesn't like typecast */
 346 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
 347                         ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
 348                         CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
 349 #define CONFIG_SYS_INIT_RAM_SIZE        0x00004000
 350 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - \
 351                                                 GENERATED_GBL_DATA_SIZE)
 352 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 353 #define CONFIG_SYS_MONITOR_LEN          (768 * 1024)
 354 #define CONFIG_SYS_MALLOC_LEN           (4 * 1024 * 1024)
 355
 356 /*
 357  * Serial Port
 358  */
 359 #define CONFIG_SYS_NS16550_SERIAL
 360 #define CONFIG_SYS_NS16550_REG_SIZE     1
 361 #define CONFIG_SYS_NS16550_CLK          (get_bus_freq(0)/2)
 362 #define CONFIG_SYS_BAUDRATE_TABLE       \
 363         {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
 364 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500)
 365 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600)
 366 #define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500)
 367 #define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600)
 368
 369 /*
 370  * I2C
 371  */
 372 #if !CONFIG_IS_ENABLED(DM_I2C)
 373 #define CONFIG_SYS_I2C_LEGACY
 374 #define CONFIG_SYS_FSL_I2C_SLAVE   0x7F
 375 #define CONFIG_SYS_FSL_I2C2_SLAVE  0x7F
 376 #define CONFIG_SYS_FSL_I2C3_SLAVE  0x7F
 377 #define CONFIG_SYS_FSL_I2C4_SLAVE  0x7F
 378 #define CONFIG_SYS_FSL_I2C_OFFSET  0x118000
 379 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x118100
 380 #define CONFIG_SYS_FSL_I2C3_OFFSET 0x119000
 381 #define CONFIG_SYS_FSL_I2C4_OFFSET 0x119100
 382 #define CONFIG_SYS_FSL_I2C_SPEED   100000
 383 #define CONFIG_SYS_FSL_I2C2_SPEED  100000
 384 #define CONFIG_SYS_FSL_I2C3_SPEED  100000
 385 #define CONFIG_SYS_FSL_I2C4_SPEED  100000
 386 #endif
 387
 388 #define CONFIG_SYS_I2C_FSL
 389
 390 #define I2C_MUX_PCA_ADDR_PRI    0x77 /* I2C bus multiplexer,primary */
 391 #define I2C_MUX_PCA_ADDR_SEC1   0x75 /* I2C bus multiplexer,secondary 1 */
 392 #define I2C_MUX_PCA_ADDR_SEC2   0x76 /* I2C bus multiplexer,secondary 2 */
 393 #define I2C_MUX_CH_DEFAULT      0x8
 394
 395 #define I2C_MUX_CH_VOL_MONITOR 0xa
 396
 397 /* Voltage monitor on channel 2*/
 398 #define I2C_VOL_MONITOR_ADDR           0x40
 399 #define I2C_VOL_MONITOR_BUS_V_OFFSET   0x2
 400 #define I2C_VOL_MONITOR_BUS_V_OVF      0x1
 401 #define I2C_VOL_MONITOR_BUS_V_SHIFT    3
 402
 403 #define CONFIG_VID_FLS_ENV              "t208xqds_vdd_mv"
 404 #ifndef CONFIG_SPL_BUILD
 405 #define CONFIG_VID
 406 #endif
 407 #define CONFIG_VOL_MONITOR_IR36021_SET
 408 #define CONFIG_VOL_MONITOR_IR36021_READ
 409 /* The lowest and highest voltage allowed for T208xQDS */
 410 #define VDD_MV_MIN                      819
 411 #define VDD_MV_MAX                      1212
 412
 413 /*
 414  * RapidIO
 415  */
 416 #define CONFIG_SYS_SRIO1_MEM_VIRT       0xa0000000
 417 #define CONFIG_SYS_SRIO1_MEM_PHYS       0xc20000000ull
 418 #define CONFIG_SYS_SRIO1_MEM_SIZE       0x10000000 /* 256M */
 419 #define CONFIG_SYS_SRIO2_MEM_VIRT       0xb0000000
 420 #define CONFIG_SYS_SRIO2_MEM_PHYS       0xc30000000ull
 421 #define CONFIG_SYS_SRIO2_MEM_SIZE       0x10000000 /* 256M */
 422 /*
 423  * for slave u-boot IMAGE instored in master memory space,
 424  * PHYS must be aligned based on the SIZE
 425  */
 426 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull
 427 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull
 428 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE     0x100000 /* 1M */
 429 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull
 430 /*
 431  * for slave UCODE and ENV instored in master memory space,
 432  * PHYS must be aligned based on the SIZE
 433  */
 434 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull
 435 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull
 436 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE    0x40000 /* 256K */
 437
 438 /* slave core release by master*/
 439 #define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4
 440 #define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */
 441
 442 /*
 443  * SRIO_PCIE_BOOT - SLAVE
 444  */
 445 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
 446 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000
 447 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \
 448                 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR)
 449 #endif
 450
 451 /*
 452  * eSPI - Enhanced SPI
 453  */
 454
 455 /*
 456  * General PCI
 457  * Memory space is mapped 1-1, but I/O space must start from 0.
 458  */
 459 #define CONFIG_PCIE1            /* PCIE controller 1 */
 460 #define CONFIG_PCIE2            /* PCIE controller 2 */
 461 #define CONFIG_PCIE3            /* PCIE controller 3 */
 462 #define CONFIG_PCIE4            /* PCIE controller 4 */
 463 #define CONFIG_SYS_PCI_64BIT    /* enable 64-bit PCI resources */
 464 /* controller 1, direct to uli, tgtid 3, Base address 20000 */
 465 #define CONFIG_SYS_PCIE1_MEM_VIRT       0x80000000
 466 #define CONFIG_SYS_PCIE1_MEM_PHYS       0xc00000000ull
 467 #define CONFIG_SYS_PCIE1_IO_VIRT        0xf8000000
 468 #define CONFIG_SYS_PCIE1_IO_PHYS        0xff8000000ull
 469
 470 /* controller 2, Slot 2, tgtid 2, Base address 201000 */
 471 #define CONFIG_SYS_PCIE2_MEM_VIRT       0xa0000000
 472 #define CONFIG_SYS_PCIE2_MEM_PHYS       0xc20000000ull
 473 #define CONFIG_SYS_PCIE2_IO_VIRT        0xf8010000
 474 #define CONFIG_SYS_PCIE2_IO_PHYS        0xff8010000ull
 475
 476 /* controller 3, Slot 1, tgtid 1, Base address 202000 */
 477 #define CONFIG_SYS_PCIE3_MEM_VIRT       0xb0000000
 478 #define CONFIG_SYS_PCIE3_MEM_PHYS       0xc30000000ull
 479 #define CONFIG_SYS_PCIE3_IO_VIRT        0xf8020000
 480 #define CONFIG_SYS_PCIE3_IO_PHYS        0xff8020000ull
 481
 482 /* controller 4, Base address 203000 */
 483 #define CONFIG_SYS_PCIE4_MEM_VIRT       0xc0000000
 484 #define CONFIG_SYS_PCIE4_MEM_PHYS       0xc40000000ull
 485 #define CONFIG_SYS_PCIE4_IO_PHYS        0xff8030000ull
 486
 487 #ifdef CONFIG_PCI
 488 #define CONFIG_PCI_SCAN_SHOW    /* show pci devices on startup */
 489 #endif
 490
 491 /* Qman/Bman */
 492 #ifndef CONFIG_NOBQFMAN
 493 #define CONFIG_SYS_BMAN_NUM_PORTALS     18
 494 #define CONFIG_SYS_BMAN_MEM_BASE        0xf4000000
 495 #define CONFIG_SYS_BMAN_MEM_PHYS        0xff4000000ull
 496 #define CONFIG_SYS_BMAN_MEM_SIZE        0x02000000
 497 #define CONFIG_SYS_BMAN_SP_CENA_SIZE    0x4000
 498 #define CONFIG_SYS_BMAN_SP_CINH_SIZE    0x1000
 499 #define CONFIG_SYS_BMAN_CENA_BASE       CONFIG_SYS_BMAN_MEM_BASE
 500 #define CONFIG_SYS_BMAN_CENA_SIZE       (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
 501 #define CONFIG_SYS_BMAN_CINH_BASE       (CONFIG_SYS_BMAN_MEM_BASE + \
 502                                         CONFIG_SYS_BMAN_CENA_SIZE)
 503 #define CONFIG_SYS_BMAN_CINH_SIZE       (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
 504 #define CONFIG_SYS_BMAN_SWP_ISDR_REG    0xE08
 505 #define CONFIG_SYS_QMAN_NUM_PORTALS     18
 506 #define CONFIG_SYS_QMAN_MEM_BASE        0xf6000000
 507 #define CONFIG_SYS_QMAN_MEM_PHYS        0xff6000000ull
 508 #define CONFIG_SYS_QMAN_MEM_SIZE        0x02000000
 509 #define CONFIG_SYS_QMAN_SP_CENA_SIZE    0x4000
 510 #define CONFIG_SYS_QMAN_SP_CINH_SIZE    0x1000
 511 #define CONFIG_SYS_QMAN_CENA_BASE       CONFIG_SYS_QMAN_MEM_BASE
 512 #define CONFIG_SYS_QMAN_CENA_SIZE       (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
 513 #define CONFIG_SYS_QMAN_CINH_BASE       (CONFIG_SYS_QMAN_MEM_BASE + \
 514                                         CONFIG_SYS_QMAN_CENA_SIZE)
 515 #define CONFIG_SYS_QMAN_CINH_SIZE       (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
 516 #define CONFIG_SYS_QMAN_SWP_ISDR_REG    0xE08
 517
 518 #define CONFIG_SYS_DPAA_FMAN
 519 #define CONFIG_SYS_DPAA_PME
 520 #define CONFIG_SYS_PMAN
 521 #define CONFIG_SYS_DPAA_DCE
 522 #define CONFIG_SYS_DPAA_RMAN            /* RMan */
 523 #define CONFIG_SYS_INTERLAKEN
 524
 525 /* Default address of microcode for the Linux Fman driver */
 526 #if defined(CONFIG_SPIFLASH)
 527 /*
 528  * env is stored at 0x100000, sector size is 0x10000, ucode is stored after
 529  * env, so we got 0x110000.
 530  */
 531 #define CONFIG_SYS_FMAN_FW_ADDR 0x110000
 532 #elif defined(CONFIG_SDCARD)
 533 /*
 534  * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
 535  * about 1MB (2048 blocks), Env is stored after the image, and the env size is
 536  * 0x2000 (16 blocks), 8 + 2048 + 16 = 2072, enlarge it to 2080.
 537  */
 538 #define CONFIG_SYS_FMAN_FW_ADDR (512 * 0x820)
 539 #elif defined(CONFIG_MTD_RAW_NAND)
 540 #define CONFIG_SYS_FMAN_FW_ADDR (11 * CONFIG_SYS_NAND_BLOCK_SIZE)
 541 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
 542 /*
 543  * Slave has no ucode locally, it can fetch this from remote. When implementing
 544  * in two corenet boards, slave's ucode could be stored in master's memory
 545  * space, the address can be mapped from slave TLB->slave LAW->
 546  * slave SRIO or PCIE outbound window->master inbound window->
 547  * master LAW->the ucode address in master's memory space.
 548  */
 549 #define CONFIG_SYS_FMAN_FW_ADDR 0xFFE00000
 550 #else
 551 #define CONFIG_SYS_FMAN_FW_ADDR 0xEFF00000
 552 #endif
 553 #define CONFIG_SYS_QE_FMAN_FW_LENGTH    0x10000
 554 #define CONFIG_SYS_FDT_PAD              (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
 555 #endif /* CONFIG_NOBQFMAN */
 556
 557 #ifdef CONFIG_SYS_DPAA_FMAN
 558 #define RGMII_PHY1_ADDR 0x1
 559 #define RGMII_PHY2_ADDR 0x2
 560 #define FM1_10GEC1_PHY_ADDR       0x3
 561 #define SGMII_CARD_PORT1_PHY_ADDR 0x1C
 562 #define SGMII_CARD_PORT2_PHY_ADDR 0x1D
 563 #define SGMII_CARD_PORT3_PHY_ADDR 0x1E
 564 #define SGMII_CARD_PORT4_PHY_ADDR 0x1F
 565 #endif
 566
 567 #ifdef CONFIG_FMAN_ENET
 568 #define CONFIG_ETHPRIME         "FM1@DTSEC3"
 569 #endif
 570
 571 /*
 572  * SATA
 573  */
 574 #ifdef CONFIG_FSL_SATA_V2
 575 #define CONFIG_SYS_SATA_MAX_DEVICE      2
 576 #define CONFIG_SATA1
 577 #define CONFIG_SYS_SATA1                CONFIG_SYS_MPC85xx_SATA1_ADDR
 578 #define CONFIG_SYS_SATA1_FLAGS          FLAGS_DMA
 579 #define CONFIG_SATA2
 580 #define CONFIG_SYS_SATA2                CONFIG_SYS_MPC85xx_SATA2_ADDR
 581 #define CONFIG_SYS_SATA2_FLAGS          FLAGS_DMA
 582 #define CONFIG_LBA48
 583 #endif
 584
 585 /*
 586  * USB
 587  */
 588 #ifdef CONFIG_USB_EHCI_HCD
 589 #define CONFIG_USB_EHCI_FSL
 590 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 591 #define CONFIG_HAS_FSL_DR_USB
 592 #endif
 593
 594 /*
 595  * SDHC
 596  */
 597 #ifdef CONFIG_MMC
 598 #define CONFIG_SYS_FSL_ESDHC_ADDR       CONFIG_SYS_MPC85xx_ESDHC_ADDR
 599 #define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT
 600 #endif
 601
 602 /*
 603  * Dynamic MTD Partition support with mtdparts
 604  */
 605
 606 /*
 607  * Environment
 608  */
 609 #define CONFIG_LOADS_ECHO       /* echo on for serial download */
 610 #define CONFIG_SYS_LOADS_BAUD_CHANGE    /* allow baudrate change */
 611
 612 /*
 613  * Miscellaneous configurable options
 614  */
 615 #define CONFIG_SYS_LOAD_ADDR    0x2000000 /* default load address */
 616
 617 /*
 618  * For booting Linux, the board info and command line data
 619  * have to be in the first 64 MB of memory, since this is
 620  * the maximum mapped by the Linux kernel during initialization.
 621  */
 622 #define CONFIG_SYS_BOOTMAPSZ    (64 << 20)      /* Initial map for Linux*/
 623 #define CONFIG_SYS_BOOTM_LEN    (64 << 20)      /* Increase max gunzip size */
 624
 625 #ifdef CONFIG_CMD_KGDB
 626 #define CONFIG_KGDB_BAUDRATE    230400  /* speed to run kgdb serial port */
 627 #define CONFIG_KGDB_SER_INDEX   2       /* which serial port to use */
 628 #endif
 629
 630 /*
 631  * Environment Configuration
 632  */
 633 #define CONFIG_ROOTPATH  "/opt/nfsroot"
 634 #define CONFIG_BOOTFILE  "uImage"
 635 #define CONFIG_UBOOTPATH "u-boot.bin"   /* U-Boot image on TFTP server */
 636
 637 /* default location for tftp and bootm */
 638 #define CONFIG_LOADADDR         1000000
 639 #define __USB_PHY_TYPE          utmi
 640
 641 #define CONFIG_EXTRA_ENV_SETTINGS                               \
 642         "hwconfig=fsl_ddr:"                                     \
 643         "ctlr_intlv=" __stringify(CTRL_INTLV_PREFERED) ","      \
 644         "bank_intlv=auto;"                                      \
 645         "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\
 646         "netdev=eth0\0"                                         \
 647         "uboot=" __stringify(CONFIG_UBOOTPATH) "\0"             \
 648         "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0"     \
 649         "tftpflash=tftpboot $loadaddr $uboot && "               \
 650         "protect off $ubootaddr +$filesize && "                 \
 651         "erase $ubootaddr +$filesize && "                       \
 652         "cp.b $loadaddr $ubootaddr $filesize && "               \
 653         "protect on $ubootaddr +$filesize && "                  \
 654         "cmp.b $loadaddr $ubootaddr $filesize\0"                \
 655         "consoledev=ttyS0\0"                                    \
 656         "ramdiskaddr=2000000\0"                                 \
 657         "ramdiskfile=t2080qds/ramdisk.uboot\0"                  \
 658         "fdtaddr=1e00000\0"                                     \
 659         "fdtfile=t2080qds/t2080qds.dtb\0"                       \
 660         "bdev=sda3\0"
 661
 662 /*
 663  * For emulation this causes u-boot to jump to the start of the
 664  * proof point app code automatically
 665  */
 666 #define CONFIG_PROOF_POINTS                             \
 667         "setenv bootargs root=/dev/$bdev rw "           \
 668         "console=$consoledev,$baudrate $othbootargs;"   \
 669         "cpu 1 release 0x29000000 - - -;"               \
 670         "cpu 2 release 0x29000000 - - -;"               \
 671         "cpu 3 release 0x29000000 - - -;"               \
 672         "cpu 4 release 0x29000000 - - -;"               \
 673         "cpu 5 release 0x29000000 - - -;"               \
 674         "cpu 6 release 0x29000000 - - -;"               \
 675         "cpu 7 release 0x29000000 - - -;"               \
 676         "go 0x29000000"
 677
 678 #define CONFIG_HVBOOT                           \
 679         "setenv bootargs config-addr=0x60000000; "      \
 680         "bootm 0x01000000 - 0x00f00000"
 681
 682 #define CONFIG_ALU                              \
 683         "setenv bootargs root=/dev/$bdev rw "           \
 684         "console=$consoledev,$baudrate $othbootargs;"   \
 685         "cpu 1 release 0x01000000 - - -;"               \
 686         "cpu 2 release 0x01000000 - - -;"               \
 687         "cpu 3 release 0x01000000 - - -;"               \
 688         "cpu 4 release 0x01000000 - - -;"               \
 689         "cpu 5 release 0x01000000 - - -;"               \
 690         "cpu 6 release 0x01000000 - - -;"               \
 691         "cpu 7 release 0x01000000 - - -;"               \
 692         "go 0x01000000"
 693
 694 #define CONFIG_LINUX                            \
 695         "setenv bootargs root=/dev/ram rw "             \
 696         "console=$consoledev,$baudrate $othbootargs;"   \
 697         "setenv ramdiskaddr 0x02000000;"                \
 698         "setenv fdtaddr 0x00c00000;"                    \
 699         "setenv loadaddr 0x1000000;"                    \
 700         "bootm $loadaddr $ramdiskaddr $fdtaddr"
 701
 702 #define CONFIG_HDBOOT                                   \
 703         "setenv bootargs root=/dev/$bdev rw "           \
 704         "console=$consoledev,$baudrate $othbootargs;"   \
 705         "tftp $loadaddr $bootfile;"                     \
 706         "tftp $fdtaddr $fdtfile;"                       \
 707         "bootm $loadaddr - $fdtaddr"
 708
 709 #define CONFIG_NFSBOOTCOMMAND                   \
 710         "setenv bootargs root=/dev/nfs rw "     \
 711         "nfsroot=$serverip:$rootpath "          \
 712         "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
 713         "console=$consoledev,$baudrate $othbootargs;"   \
 714         "tftp $loadaddr $bootfile;"             \
 715         "tftp $fdtaddr $fdtfile;"               \
 716         "bootm $loadaddr - $fdtaddr"
 717
 718 #define CONFIG_RAMBOOTCOMMAND                           \
 719         "setenv bootargs root=/dev/ram rw "             \
 720         "console=$consoledev,$baudrate $othbootargs;"   \
 721         "tftp $ramdiskaddr $ramdiskfile;"               \
 722         "tftp $loadaddr $bootfile;"                     \
 723         "tftp $fdtaddr $fdtfile;"                       \
 724         "bootm $loadaddr $ramdiskaddr $fdtaddr"
 725
 726 #define CONFIG_BOOTCOMMAND              CONFIG_LINUX
 727
 728 #include <asm/fsl_secure_boot.h>
 729
 730 #endif  /* __T208xQDS_H */